Search Results (830)

The aim of this work was to produce bone scaffolds containing whey protein isolate and pearl powder and to conduct a preliminary assessment of the biomedical potential in vitro and in vivo. This included analysis of structural, physicochemical, mechanical, and biological properties, which revealed that biomaterials containing pearl powder exhibited an enhanced porous structure, increasing absorptive properties, and decreasing proteolytic capacity with increasing inorganic component content. Pearl powder content in the biomaterials did not clearly influence their mechanical properties or their ability to release calcium ions, as well as proteins. Extracts obtained from all tested biomaterials showed no cytotoxicity in vitro. The surfaces of all biomaterials promoted normal human osteoblast growth, proliferation, and osteogenic differentiation. Furthermore, all biomaterials did not display toxicity in vivo, but no changes in Danio rerio were observed after evaluation of the biomaterial containing the highest amount of pearl powder–10% v/w (marked as WPI/P10). Taking all the obtained results into account, it appears that this biomaterial can be promising for bone scaffolds and similar applications, thanks to its porous structure, high cytocompatibility in vitro, and lack of toxicity in vivo. However, advanced studies will be conducted in the future. Full article

A small, strongly schistose Ni-laterite occurrence at the Vermion ophiolite (40°26′ Ν, 22°10′ Ε), Northen Greece, along a strong shear zone, is characterized by relatively high Ni, Co and Mn contents, magnetite as the dominant mineral, garnet (grossularite), theophrastite [β-Ni(OH)₂], otwayite-like phase (ideally Ni₂CO₃(OH)₂.H₂O), (Ni, Co, Mn)-hydroxides, and Ni-phyllosilicates. New analytical data, including black-white and color back-scattered electron images (BSEIs), elemental mapping and scanning, and Raman Spectroscopy, alongside silicates and hydroxides revealed the presence of varying silica content (less than 1 to 29 wt.%) in theophrastite and in (Ni, Co, Mn ± Fe)-hydroxides, although the X-ray powder diffraction data correspond to those of pure hydroxides. The gradual stacking of fine fibrous otwayite-like crystals to the boundaries of successive thin layers and within layers themselves, results in porous mineral phases of varying density shifting towards more compact mineral with increasing residence time. The presented data suggest that a potential explanation of the presence of Si in theophrastite may be the precipitation of Si after initial Ni-hydroxyl-carbonate fine crystals deposition. A potential sequence of the stability of Ni-minerals at Vermion may be as follows: Hydroxyl-carbonates < [β-Ni(OH)₂] (theophrastite) < (Ni, Co, Mn)(OH)₂ < Ni-phyllosilicates; this may be a significant factor for Ni-exploration in Ni-larerite deposits. Full article

The practical application of powdered photocatalysts is significantly hindered by challenges in recyclability and structural instability. This work proposes a sustainable immobilization strategy by integrating BiVO₄ nanoparticles into a sodium alginate (SA) aerogel scaffold through a facile freeze-drying approach. The abundant hydroxyl/carboxyl groups of SA enable uniform dispersion of BiVO₄ within the porous network, while the aerogel architecture enhances light-harvesting efficiency and mass transfer kinetics. Innovatively, peroxymonosulfate (PMS) was introduced to synergistically couple photocatalysis with sulfate radical-based advanced oxidation processes (SR-AOPs), where the photogenerated electrons from BiVO₄ effectively activate PMS to yield high-activity ·SO₄⁻ radicals. The optimized BiVO₄/SA aerogel achieves nearly complete removal of Rhodamine B within 2 h under visible light, which is competitive to pure BiVO₄ powders. In addition, the mechanically robust aerogel exhibits exceptional reusability, retaining ~90% efficiency after five cycles without structural collapse. This work provides a paradigm for designing recyclable photocatalyst carriers with dual oxidation pathways, demonstrating significant potential for industrial wastewater treatment. Full article

Porous CaCO₃ vaterite particles have been widely used as drug carriers for biomedical applications due to their high biocompatibility and low production costs. However, controlling the particle size and porosity of CaCO₃ nanoparticles with the desired crystalline phase is still challenging. In this study, we have systematically investigated the preparation of CaCO₃ nanoparticles under various conditions including precursor types/ratios/concentrations, additive concentrations (ethylene glycol), and temperatures. The materials were fully characterized by optical microscopy, scanning and transmission electron microscopy, infrared spectroscopy, powder X-ray diffraction, dynamic laser scattering, thermogravimetric analysis, and gas sorption. The impacts of the reaction parameters were rationalized and the mechanism for the formation of porous vaterite particles was suggested. It was possible to produce porous vaterite nanoparticles (200 nm) under the optimized conditions, which were further used as drug carrier to upload a model drug curcumin. The potential of using these vaterite particles for controlled drug release was demonstrated. Full article

The rational design of high-performance microwave absorbers with broadband coverage, superior attenuation, and environmental durability is critical for addressing challenges in both defense and civilian technologies. High-entropy alloys (HEAs) exhibit atomic-scale asymmetric arrangements, demonstrating exceptional potential for microwave absorption through their unique lattice distortion, high entropy, sluggish diffusion, and “cocktail effect”. This critical review article provides an overview of the progress made in the development and understanding of HEA-based microwave absorbing materials. Initially, the microwave dissipation mechanisms for HEAs were analyzed, where atomic-scale distortions enhance polarization loss and broaden resonance bandwidth. Subsequently, key synthesis techniques like mechanical alloying and carbothermal shock are discussed, highlighting non-equilibrium processing for phase engineering. Building on these foundations, the discussion then progresses to evaluate four principal material design approaches: (1) compositionally-tuned powders, (2) multifunctional core–shell structures, (3) phase-controlled architectures, and (4) two-dimensional/porous configurations, each demonstrating distinct performance advantages. Finally, the discussion concludes by addressing current challenges in quantitative property modeling and industrial scalability while outlining future directions, including machine learning-assisted design and flexible integration, providing comprehensive guidance for developing next-generation high-performance microwave absorbing materials. Full article

TiAl alloy offers advantages including low density, high specific strength and stiffness, and excellent high-temperature creep resistance. It is widely used in the aerospace, automotive, and chemical sectors, as well as in other fields. However, at temperatures of 800 °C and above, it forms a porous oxide film predominantly composed of TiO₂, which fails to provide adequate protection. Applying high-temperature protective coatings is therefore essential. Oxides demonstrating protective efficacy at elevated temperatures include Al₂O₃, Cr₂O₃, and SiO₂. The Pilling–Bedworth Ratio (PBR)—defined as the ratio of the volume of the oxide formed to the volume of the metal consumed—serves as a critical criterion for assessing oxide film integrity. A PBR value greater than 1 but less than 2 indicates superior film integrity and enhanced oxidation resistance. Among common oxides, Al₂O₃ exhibits a PBR value within this optimal range (1−2), rendering aluminum-based compound coatings the most extensively utilized. Aluminum coatings can be applied via methods such as pack cementation, thermal spraying, and hot-dip aluminizing. Pack cementation, being the simplest to operate, is widely employed. In this study, a powder mixture with the composition Al:Al₂O₃:NH₄Cl:CeO₂ = 30:66:3:1 was used to aluminize γ-TiAl intermetallic compound specimens via pack cementation at 600 °C for 5 h. Subsequent isothermal oxidation at 900 °C for 20 h yielded an oxidation kinetic curve adhering to the parabolic rate law. This treatment significantly enhanced the high-temperature oxidation resistance of the γ-TiAl intermetallic compound, thereby broadening its potential application scenarios. Full article

This study aimed to develop a functional powder using whey and milk matrices, leveraging the protective capacity of chia–alginate hydrogels and the advantages of electrohydrodynamic spraying (EHDA), a non-thermal technique suitable for encapsulating probiotic cells under stress conditions commonly encountered in food processing. A hydrogel matrix composed of chia seed mucilage and sodium alginate was used to form a biopolymeric network that protected probiotic cells during processing. The encapsulation efficiency reached 99.0 ± 0.01%, and bacterial viability remained above 9.9 log₁₀ CFU/mL after lyophilization, demonstrating the excellent protective capacity of the hydrogel matrix. Microstructural analysis using confocal laser scanning microscopy (CLSM) revealed well-retained cell morphology and homogeneous distribution within the hydrogel matrix while, in contrast, scanning electron microscopy (SEM) showed spherical, porous microcapsules with distinct surface characteristics influenced by the encapsulation method. Encapsulates were incorporated into beverages flavored with red fruits and pear and subsequently freeze-dried. The resulting powders were analyzed for moisture, protein, lipids, carbohydrates, fiber, and color determinations. The results were statistically analyzed using ANOVA and response surface methodology, highlighting the impact of ingredient ratios on nutritional composition. Raman spectroscopy identified molecular features associated with casein, lactose, pectins, anthocyanins, and other functional compounds, confirming the contribution of both matrix and encapsulants maintaining the structural characteristics of the product. The presence of antioxidant bands supported the functional potential of the powder formulations. Chia–alginate hydrogels effectively encapsulated L. reuteri, maintaining cell viability and enabling their incorporation into freeze-dried beverage powders. This approach offers a promising strategy for the development of next-generation functional food gels with enhanced probiotic stability, nutritional properties, and potential application in health-promoting dairy systems. Full article

Porous intermetallic compounds have the properties of porous materials as well as a combination of covalent and metallic bonds, and they exhibit high porosity, structural stability, and corrosion resistance. In this work, a porous TiNi₃ intermetallic compound was fabricated through reactive synthesis of elemental powders. Next, detailed studies of its phase composition and pore structure characteristics at different sintering temperatures, as well as its corrosion behavior against an alkaline environment, were carried out. The results show that the as-prepared porous TiNi₃ intermetallic compound has abundant pore structures, with an open porosity of 56.5%, which can be attributed to a combination of the bridging effects of initial powder particles and the Kirkendall effect occurring during the sintering process. In 1 M KOH solution, a higher positive corrosion potential (−0.979 V_SCE) and a lower corrosion current density (1.18 × 10⁻⁴ A∙cm⁻²) were exhibited by the porous TiNi₃ intermetallic compound, compared to the porous Ni, reducing the thermodynamic corrosion tendency and the corrosion rate. The corresponding corrosion process is controlled by the charge transfer process, and the increased charge transfer resistance value (713.9 Ω⋅cm²) of TiNi₃ makes it more difficult to charge-transfer than porous Ni (204.5 Ω⋅cm²), thus decreasing the rate of electrode reaction. The formation of a more stable passive film with the incorporation of Ti contributes to this improved corrosion resistance performance. Full article

Reaction bonding (RB) using Al powder is an effective method for preparing porous ceramics with low shrinkage, high porosity, and high strength. However, it remains challenging to optimize mechanical strength and oil conductivity simultaneously for atomizer applications. Herein, aiming at addressing this issue, porous Al₂O₃ ceramics with ultra-high mechanical strength and oil conductivity were fabricated via the RB process using polymethyl methacrylate (PMMA) microspheres as the pore-forming agent. The pore structure was gradually optimized by regulating the additive amount, particle size, and particle gradation of PMMA microspheres. The bimodal pores, formed by Al oxidation-induced hollow structures (enhancing bonding force) and burnout of large-sized PMMA microspheres, significantly improved mechanical strength; meanwhile, three-dimensional interconnected pores derived from particle gradation increased the diversity and quantity of oil-conduction channels, boosting oil conductivity. Consequently, under an open porosity of 58.2 ± 0.1%, a high compressive strength of 7.9 ± 0.3 MPa (a 54.7% improvement) and an excellent oil conductivity of 2.1 ± 0.0 mg·s⁻¹ (a 46.5% improvement) were achieved. This superior performance combination, overcoming the trade-off between strength and oil conductivity, demonstrates substantial application potential in atomizers. Full article

This study explored the potential of reusing eggshell powders as a renewable activating agent for producing porous carbon materials from coffee husk. Carbonization and activation experiments were conducted by heating the samples at a rate of 10 °C/min up to 850 °C under a nitrogen atmosphere. A custom-designed double steel-mesh sample holder was used to hold approximately 2.0 g coffee husk on the top, with varying masses of eggshell at the bottom to achieve eggshells to coffee husk mass ratios of 2:1, 4:1, 6:1 and 8:1. The results demonstrated that CO₂ released from the thermal decomposition of the eggshell powder significantly enhanced pore development at 850 °C. Compared to the pore properties of carbon material produced without eggshell (e.g., BET surface area of 321 m²/g), the activated carbon samples exhibited substantially improved pore properties (e.g., BET surface area in the range of 592 to 715 m²/g). Furthermore, the pore characteristics improved consistently with increasing eggshell content. Observations by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and Fourier-transform infrared spectroscopy (FTIR) confirmed the structural and chemical transformations of the resulting carbon materials. Under optimal carbonization-activation conditions, the resulting carbon materials derived from coffee husk exhibited microporous structures and slit-shaped pores, as indicated by the Type I isotherms and H4 hysteresis loops. Full article

Date seeds, a by-product of the pitted-date industry, are often discarded as waste. This study investigated the interaction between date seed powder and starch at different concentrations (0, 1, 5, 10, and 20 g/25 g composite) and temperatures (40 °C and 70 °C). The results revealed that the hygroscopicity of date seed powder (9.94 g/100 g) was lower than starch (13.39 g/100 g), and its water absorption (75.8%) was also lower than starch (88.3%), leading to a reduced absorbance capacity in composites. However, the solubility increased with a higher date seed content due to its greater solubility (17.8 g/L) compared to starch (1.6 g/L). A morphological analysis showed rough, agglomerated particles in date seed powder, while starch had smooth, spherical shapes. This study also found that the composites formed larger particles at 40 °C and porous structures at 70 °C. Crystallinity decreased from 41.6% to 12.8% (40 °C) and from 24.0% to 11.3% (70 °C). A thermal analysis revealed three endothermic peaks (glass transitions and solid melting), with an additional oil-melting peak in high-seed samples. FTIR spectra showed changes in peak intensities and locations upon seed incorporation. Overall, these findings revealed that, the incorporation of date seed powder–starch composites into bakery formulations offers a promising strategy for developing fiber-enriched products, positioning them as functional ingredients with added nutritional value. Full article

In order to improve the durability of loess-based composite coal gangue porous planting concrete (LCPC), the effects of fly ash and slag powder content on the durability and microstructure of LCPC were studied. In this paper, fly ash and slag powder were mixed into LCPC, and freeze-thaw cycle and dry-wet cycle tests were carried out. The compressive strength, dynamic elastic modulus, and mass change were used as evaluation indices to determine the optimal mix ratio for LCPC durability. Scanning electron microscopy (SEM) was performed, and the experimental design was carried out with the water–cement ratio, fly ash, and slag powder content as variables. The microstructure characteristics of LCPC were analyzed. The results show that the maximum number of freeze-thaw cycles can reach 35 times and the maximum number of dry-wet cycles can reach 50 when 5% fly ash and 20% slag powder are used. With an increase in the water-cement ratio, the skeleton of the loess gradually became complete, and its structure became more compact. In the micro-morphology diagram, the mixed fly ash and slag powder particles are not obvious, but with an increase in dosage, the size of the cracks and pores gradually decreases. The incorporation of fly ash and slag powder can play a positive role in the durability of LCPC and improvement of its microstructure. The results of this study are crucial for improving the application performance of ecological restoration, soil improvement, and long-term stability of structures, and can provide a scientific basis for the sustainable development of environmentally friendly building materials. Full article

The objective of the current research is to investigate the role of Neusilin US2 as a porous carrier for improving the drug loading and stability of Ezetimibe (EZB) by hot melt extrusion (HME). The amorphous solid dispersions (ASDs) were developed from 10–40% of drug loading using Kollidon VA 64 (Copovidone) as a polymer matrix and Neusilin US2 as a porous carrier. The solid-state characterization of EZB was studied using differential scanning calorimetry (DSC), powder X-ray diffraction (PXRD), and Fourier transform infrared spectroscopy (FTIR). The formulation blends were characterized for flow properties, and CTC (compressibility, tabletability, compactibility) profile. The in-vitro drug release profiles were studied in 0.1 N HCl (pH 1.2). The incorporation of Neusilin US2 has facilitated the development of ASDs up to 40% of drug loading. The CTC profile has demonstrated excellent tabletability for the ternary (EZB, copovidone and Neusilin) dispersions over binary dispersion (EZB and copovidone) formulations. The tablet formulations with binary (20%) and ternary (30% and 40%) dispersions have demonstrated complete dissolution of the drug in 30 min in 0.1 N HCl (pH 1.2). The incorporation of copovidone has prevented the recrystallization of the drug in the solution state. Upon storage of formulations at accelerated conditions, the stability of ternary dispersion tablets was preserved attributing to the entrapment of the drug within Neusilin pores thereby inhibiting molecular mobility. Based on the observations, the current research concludes that it is feasible to incorporate Neusilin US2 to improve the drug loading and stability of ASD systems. Full article

Additively manufactured (AM) parts have been applied in many areas with the risk of cavitation erosion (CE), and pores are common defects in AM metals. However, the role of pores in CE is still unclear, and a systematic investigation is needed. In this study, 316L stainless steel was selected as a model material and produced using laser powder bed fusion; the porosity was 6.4%. The morphological evolution of various pores during CE was investigated via electron backscatter diffraction and scanning electron microscopy. It was found that material removal easily occurred around large polygonal pores. The critical size for large polygonal pores was estimated to be between 13 and 20 μm. For narrow pores, concavity first appeared around the pores during CE, and then the narrow pores closed. Small spherical pores with sizes of 3–9 μm showed strong resistance to CE, and no damage occurred within the 60 min CE period. The main reason that different pores played different roles in CE was analyzed. Finally, factors for improving the CE resistance of AM metals were suggested. The research results are helpful for understanding the CE behaviors of AM metals and porous materials. Full article

Microstructural, mechanical and qualitative phase identification of durable mullite-based ceramics obtained by utilization of waste clay–diatomite has been studied. Mullite-based ceramics were fabricated using waste clay–diatomite from the Baroševac open-cast coal mine, Kolubara (Serbia). The raw material consists mainly of SiO₂ (70.5 wt%) and a moderately high content of Al₂O₃ (13.8 wt%). In order to achieve the stoichiometric mullite composition (3Al₂O₃-2SiO₂), the raw material was mixed with an appropriate amount of Al(NO₃)₃·9H₂O. After preparing the precursor powder, the green compacts were sintered at 1300, 1400 and 1500 °C for 2 h. During the process, rod-shaped mullite grains were formed, measuring approximately 5 µm in length and a diameter of 500 nm (aspect ratio 10:1). The microstructure of the sample sintered at 1500 °C resulted in a well-developed, porous, nest-like morphology. According to the X-ray diffraction analysis, the sample at 1400 °C consisted of mullite, cristobalite and corundum phases, while the sample sintered at 1500 °C contained mullite (63.24 wt%) and an amorphous phase that reached 36.7 wt%. Both samples exhibited exceptional compressive strength—up to 188 MPa at 1400 °C. However, the decrease in compressive strength to 136 MPa at 1500 °C is attributed to changes in the phase composition, the disappearance of the corundum phase and alterations in the microstructure. This occurred despite an increase in bulk density to 2.36 g/cm³ (approximately 82% of theoretical density) and a complete reduction in open porosity. The residual glassy phase (36.7 wt% at 1500 °C) is probably the key factor influencing the mechanical properties at room temperature in these ceramics produced from waste clay–diatomite. However, the excellent mechanical stability of the samples sintered at 1400 and 1500 °C, achieved without binders or additives and using mined diatomaceous earth, supports further research into mullite-based insulating materials. Mullite-based materials obtained from mining waste might be successfully used in the field of energy-efficient refractory materials and thermal insulators. for high-temperature applications Full article