Search Results (102)

In this study, we investigated how co-solvent and polymer combinations affect the performance of dye-sensitized solar cells (DSSCs) using TiO₂- and ZnO-modified carbon nanotube (CNT) composite papers as photoelectrodes. Co-solvents such as N,N-dimethylformamide (DMF) and ethylene glycol (EG) were incorporated into polyethylene glycol (PEG)- and poly(ethylene oxide) (PEO)-based gel electrolytes to increase the amount of dissolved I₂/KI redox species and evaluate their influence on the wettability of the electrolyte on CNT composite paper electrodes. PEG-based electrolytes containing DMF or EG improved the fill factor (FF) and power conversion efficiency (PCE) relative to the baseline formulation, with the EG–PEG electrolyte achieving the best single-device PCE of 15.58 × 10⁻³% using the CNT/ZnO composite paper. Replacing PEG with PEO or using PEG + PEO blends led to reduced performance, possibly because the modified polymer composition affected electrolyte wetting, spreading behavior, and penetration into the porous electrode. These results suggest that the wettability and viscosity-related behavior of gel electrolytes are important empirical factors associated with the performance of flexible paper DSSCs, and provide practical guidance for the design of paper-based photovoltaic devices. Full article

The dynamic self-assembly and phase separation of donor–acceptor blends are processes that dictate the nanoscale morphology in organic solar cells. Here, we employ a fluidics-inspired framework, integrating dissipative particle dynamics simulations with percolation theory, to investigate the morphogenesis of two non-fullerene systems: P3HT-PPerAcr and P3HT-PFTBT. We analyze monomeric and homopolymer blends, and copolymer macrostructures, focusing on how key parameters such as temperature and polymer chain flexibility govern the dynamic evolution towards percolating networks. Our simulations captured the fundamental fluidic behavior and universal scaling near the critical percolation threshold (χ_c). The critical exponent β revealed distinct universality classes dictated by system compatibility and flexibility: monomeric and flexible homopolymer blends below the critical temperature (T_c) exhibit mean field behavior (β ≈ 1). In contrast, monomeric systems above χ_c and flexible copolymers below χ_c display 3D percolation behavior (β ≈ 0.45). In the case of flexible copolymeric macromolecules, above percolation threshold a quasi-bidimensional behavior emerge with (β ≈ 0.1). Notably, semi-rigid and rigid homopolymeric and copolymeric linear architectures induce a dimensional crossover, yielding quasi-2D (β ≈ 0.14) and quasi-1D (β ≈ 0.0) morphologies. These findings establish a direct link between tunable fluidic interactions, chain dynamics, and the emergence of optimal bicontinuous percolation networks. Full article

Focusing on PM6 as the electron-donating polymer and the non-fullerene acceptors Y12 and PY-IT, this study investigates their chemical, optical, and morphological properties, as well as their compatibility in bulk heterojunction (BHJ) architectures. All materials were characterized in thin-film form using Fourier transform infrared (FTIR), and Raman spectroscopy. Binary blends of PM6:Y12 and PM6:PY-IT, along with the ternary PM6:PY-IT:Y12 system, were dissolved in o-xylene and processed into active layers by blade coating under ambient conditions. Optical properties were analyzed in solution and in thin films, providing insights into light-absorption efficiency and spectral complementarity. Nanoscale morphology and molecular packing were examined using atomic force microscopy (AFM) and grazing-incidence wide-angle X-ray scattering (GIWAXS), revealing correlations between material organization and device performance. The results highlight the importance of optimizing material selection, ink formulation, and film morphology to maximize charge-generation efficiency. Power-conversion efficiencies (PCEs) of 13.95%, 12.04%, and 12.17% were achieved for PM6:Y12, PM6:PY-IT, and PM6:PY-IT:Y12 devices, respectively. The ternary PM6:PY-IT:Y12 system demonstrated performance comparable to PM6:PY-IT, with improved miscibility and nearly aggregate-free morphologies, suggesting potential for further efficiency gains. These findings offer valuable guidance for designing high-performance, sustainable active layers, contributing to the development of next-generation organic photovoltaic technologies. Full article

The efficiency of organic solar cells is constantly improving thanks to more advanced materials. Electron donor polymers, such as PM6 and its derivatives, as well as non-fullerene acceptors (NFAs) Y6 and ITIC and their derivatives, have become the standard materials for organic solar cell studies. To broaden the absorption range of solar cells, so-called ternary organic solar cells have been developed, which add a third material to the active layer. In this work, two chromophores based on the derivatives of the Janus-dione (s-indacene-1,3,5,7(2H,6H)-tetraone) central acceptor fragment, namely TIIC-1 and TIIC-2, were synthesized. Materials were characterized using theoretical and experimental methods, including UV-Vis absorption measurements, cyclic voltammetry, photoemission yield spectroscopy, and photoconductivity. The materials were incorporated as ternary components in PM6:Y7 bulk heterojunction solar cells. The power conversion efficiency (PCE) of PM6:Y7:TIIC-1 ternary solar cells was improved compared to binary PM6:Y7 reference cells. The PCE increased from 11.9% in binary blends to 12.5% in ternary cells. This increase is attributed to the cascade-like energy level arrangement, which facilitates charge transfer in the photoactive layer. Full article

The optical properties, electronic structure and morphology of thin films of the polymer donor PTB7-Th blended with either the fullerene acceptor PC70BM or the non-fullerene acceptor ZY-4Cl were systematically investigated to evaluate their annealing-induced evolution. Thin films were characterized using UV–Vis–NIR absorption spectroscopy, spectroscopic ellipsometry, ATR-FTIR spectroscopy, atomic force microscopy (AFM), and nano-IR analysis. In situ stepwise thermal annealing revealed distinct changes in absorption edge parameters, indicating thermally induced modifications in the electronic structure of the blend films. Ellipsometric analysis showed that elevated temperatures significantly affect the refractive index and extinction coefficient spectra. AFM measurements demonstrated markedly different surface morphology evolution for the two blend systems, with pronounced needle-shaped crystallites formation observed in PTB7-Th:ZY-4Cl films after annealing at 100 °C. Nano-IR characterization identified these crystallites as predominantly PTB7-Th, indicating phase separation driven by thermal treatment. The combined optical and structural results reveal distinct annealing-induced changes in the blend. Finally, BHJ solar cells, based on PTB7-Th:PC70BM and PTB7-Th:ZY-4Cl active layers, were fabricated, and their photovoltaic response was demonstrated. Full article

This study investigates the feasibility of adding gold nanoparticles (Au-NPs) to vanadium oxide (V₂O_x) serving the hole transport layer (HTL) material oin polymer solar cells to enhance cell performance. The first part of this study used Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as a baseline and optimized the parameters of this HTL material. Then, the V₂O_x was substituted as the HTL material, and its parameters were optimized again. The second part involved incorporating an aqueous solution of gold nanoparticles (Au-NPs) with an average particle size of approximately 80 nm into V₂O_x. Due to the excitation of localized surface plasmon resonance (LSPR) by Au-NPs, the addition of Au-NPs to the V₂O_x layer can enhance the absorption efficiency of the P3HT:PCBM blended film. Therefore, compared with V₂O_x alone, the solar cells with Au-NPs incorporated into the V₂O₅ hole transport layer demonstrate improved power conversion efficiency (PCE). Full article

Conductive polymers play a crucial role in the advancement of modern technologies, particularly in the field of organic photovoltaics (OPVs). Due to advantages such as flexibility, low specific weight, ease of processing, and low production costs, polymeric materials present an attractive alternative to traditional photovoltaic materials. This study investigates the properties of a polymer blend composed of PCPDTBT (donor) and PNDI(2HD)2T (acceptor), used as the active layer in bulk heterojunction (BHJ) solar cells. The motivation behind this research was the search for a novel n-type polymer material with potentially better properties than the commonly used P(NDI2OD-T2). Comprehensive characterization of thin films made from the individual polymers and their blend was conducted using Fourier Transform Infrared Spectroscopy (FTIR), Atomic Force Microscopy (AFM), Scanning Electron Microscopy (SEM), Ultraviolet-Visible Spectroscopy (UV-Vis), four-point probe conductivity measurements, and photovoltaic testing. The prepared films were continuous, uniform, and exhibited low surface roughness (R_a < 2.5 nm). Spectroscopic analysis showed that the blend absorbs light in a broad range of the spectrum, with slight bathochromic shifts compared to individual polymers. Electrical measurements indicated that the blend’s conductivity (9.1 µS/cm) was lower than that of pure PCPDTBT but higher than that of PNDI(2HD)2T, with an optical band gap of 1.34 eV. Photovoltaic devices fabricated using the blend demonstrated an average power conversion efficiency (PCE) of 6.45%, with a short-circuit current of 14.37 mA/cm² and an open-circuit voltage of 0.89 V. These results confirm the feasibility of using PCPDTBT:PNDI(2HD)2T blends as active layers in BHJ solar cells and provide a promising direction for further optimization in terms of polymer ratio and processing conditions. Full article

Global warming and environmental pollution due to the overuse and exploitation of fossil fuels are the main issues affecting humans’ well-being. Solar energy is considered to be one of the most promising candidates for providing human society with a clean and sustainable energy supply. Thin-film organic solar cells (TFOSCs) use organic semiconductors as light-absorbing layer materials. TFOSCs have attracted wide research interest due to several advantages, such as easy fabrication, affordability, light weight, and environmental friendliness. Over the years, TFOSCs have been dominated by donor–acceptor blends based on polymer donors and fullerene acceptors. However, a new class of non-fullerene acceptors (NFAs) has gained prominence in TFOSCs owing to their significant improvement in the power conversion efficiency (PCE) of non-fullerene-based devices. In this study, the One-Dimensional Solar Cell Capacitance Simulator (SCAPS-1D) numerical simulator was used to study the performance of a device with a configuration of FTO/PDINO/PBDB-T/ITIC/CFTS/Al. Here, the PBDB-T/ITIC polymer blend represents poly[(2,6-(4,8-bis(5-(2 ethylhexyl)thiophen-2-yl)benzo [1,2-b:4,5-b]dithiophene)-co-(1,3-di(5-thiophene-2-yl)-5,7-bis(2-ethylhexyl)benzo [1,2-c:4,5-c]dithiophene-4,8-dione)] (PBDB)/3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)-indanone)-5,5,11,11-tetraki(4-hexylphenyl)-dithieno[2,3-d:2,3-d]-s-indaceno [1,2-b:5,6-b]dithiophene) (ITIC) and the non-fullerene acceptor (NFA) and serves as the absorber layer. The electron transport layer (ETL) was 2,9-Bis[3-(dimethyloxidoamino)propyl]anthra[2,1,9-def:6,5,10-d’e’f’]diisoquinoline-1,3,8,10(2H,9H)-tetrone (PDINO), and Cu₂FeSnS₄ (CFTS) was used as a hole transport layer (HTL). This research article aims to address the global challenges of environmental pollution and global warming caused by the overuse of fossil fuels by exploring alternative energy solutions. Upon optimization, the device achieved a power conversion efficiency (PCE) of 16.86%, a fill factor (FF) of 79.12%, a short-circuit current density (J_SC) of 33.19 mA cm⁻², and an open-circuit voltage (V_OC) of 0.64 V. The results obtained can guide the fabrication of NFA-based TFOSCs in the near future. Full article

Planar heterojunction (PHJ) is employed to obtain proper vertical phase separation for highly efficient polymer solar cells (PSCs). However, it heavily relies on the choice of orthogonal solvent in the production process. Here, we fabricated a pseudo-bilayer bulk heterojunction (PBHJ) PSC with cross-distribution in the vertical direction by preparing two layers of PM6 and BTP-eC9 blends in an o-XY solution with different dilution ratios to study the morphological evolution of PBHJ film. We found that the PBHJ film exhibits more uniform and suitable continuous interpenetrating network morphology and proper phase separation in the vertical direction for the formation of p-i-n structure. This provides an effective channel for exciton dissociation and charge transport, which is confirmed by both exciton generation simulations and charge dynamics measurements. The PBHJ devices can effectively inhibit trap recombination and accelerate charge separation and transfer. Based on good active layer morphology and balanced charge mobility, all-green solvent-processed PSCs with champion power conversion efficiencies (PCEs) of 18.48% and 16.83% are obtained in PM6:BTP-eC9 and PTQ10:BTP-eC9 systems, respectively. This work reveals the potential mechanism of morphological evolution induced by the PBHJ structure and provides an alternative approach for developing solution processing PSCs. Full article

In organic solar cells, the aggregation and crystallization of polymers are significant for bulk heterojunction. Blending with acceptor materials, polymer donor materials can adjust their aggregation by the movement of the chain segments. In this paper, the unfused structures based on thiophene and carbazole are respectively designed and introduced into the donor-acceptor copolymer donor materials to investigate the influence of flexible and rigid structures on polymer-aggregation leading photoelectric performance. The material and quantum chemical property investigations show that the selection and design of the blocks are important for the properties of the terpolymers, and the resulting polymer:Y6 devices achieve improvements in performance from 13.85% to 15.66% (especially for fill factors from 63.37% up to 69.81%). This result contributes to designing and optimizing efficient polymers. Full article

Organic solar cells (OSCs) are considered a very promising technology to convert solar energy to electricity and a feasible option for the energy market because of the advantages of light weight, flexibility, and roll-to-roll manufacturing. They are mainly characterized by a bulk heterojunction structure where a polymer donor is blended with an electron acceptor. Their performance is highly affected by the design of donor–acceptor conjugated polymers and the choice of suitable acceptor. In particular, benzotriazole, a typical electron-deficient penta-heterocycle, has been combined with various donors to provide wide bandgap donor polymers, which have received a great deal of attention with the development of non-fullerene acceptors (NFAs) because of their suitable matching to provide devices with relevant power conversion efficiency (PCE). Moreover, different benzotriazole-based polymers are gaining more and more interest because they are considered promising acceptors in OSCs. Since the development of a suitable method to choose generally a donor/acceptor material is a challenging issue, this review is meant to be useful especially for organic chemical scientists to understand all the progress achieved with benzotriazole-based polymers used as donors with NFAs and as acceptors with different donors in OSCs, in particular referring to the PCE. Full article

This work inspects the utilization of all-polymer solar cells (APSCs) in indoor applications under LED illumination, with a focus on boosting efficiency through simulation-based design. The study employs a SCAPS TCAD device simulator to investigate the performance of APSCs under white LED illumination at 1000 lux, with a power density of 0.305 mW/cm². Initially, the simulator is validated against experimental results obtained from a fabricated cell utilizing CD1:PBN-21 as an absorber blend and PEDOT:PSS as a hole transportation layer (HTL), where the initial measured efficiency is 16.75%. The simulation study includes an examination of both inverted and conventional cell structures. In the conventional structure, where no electron transportation layer (ETL) is present, various materials are evaluated for their suitability as the HTL. NiO emerges as the most promising HTL material, demonstrating the potential to achieve an efficiency exceeding 27%. Conversely, in the inverted configuration without an HTL, the study explores different ETL materials to engineer the band alignment at the interface. Among the materials investigated, ZnS emerges as the optimal choice, recording an efficiency of approximately 33%. In order to reveal the efficiency limitations of these devices, the interface and bulk defects are concurrently investigated. The findings of this study underscore the significance of careful material selection and structural design in optimizing the performance of APSCs for indoor applications. Full article

Ternary organic solar cells contain a single three-component photoactive layer with a wide absorption window, achieved without the need for multiple stacking. However, adding a third component into a well-known binary blend can influence the energetics, optical window, charge carrier transport, crystalline order and conversion efficiency. In the form of binary blends, the low-bandgap regioregular polymer donor poly(3-hexylthiophene-2,5-diyl), known as P3HT, is combined with the acceptor PC₆₁BM, an inexpensive fullerene derivative. Two different non-fullerene acceptors (ITIC and eh-IDTBR) are added to this binary blend to form ternary blends. A systematic comparison between binary and ternary systems was carried out as a function of the thermal annealing temperature of organic layers (100 °C and 140 °C). The power conversion efficiency (PCE) is improved due to increased fill factor (FF) and open-circuit voltage (V_oc) for thermal-annealed ternary blends at 140 °C. The transport properties of electrons and holes were investigated in binary and ternary blends following a Space-Charge-Limited Current (SCLC) protocol. A favorable balanced hole–electron mobility is obtained through the incorporation of either ITIC or eh-IDTBR. The charge transport behavior is correlated with the bulk heterojunction (BHJ) morphology deduced from atomic force microscopy (AFM), contact water angle (CWA) measurement and 2D grazing-incidence X-ray diffractometry (2D-GIXRD). Full article

Electron and hole transporting layers play a major role in high-performance and stable organic-based optoelectronic devices. This paper demonstrates detailed device engineering of multi-junction organic photovoltaics built on two different metal oxide-based electron and hole transport (buffer) layers prepared by thermal or solution-processed methods. The main focus is on the device processing parameters as well as practical details of preparation of buffer layers to give the research community a clear, step-by-step recipe to successfully replicate and build series and parallel connected multi-junction solution-based organic solar cells for their needs. Here, the recipes and deposition conditions of two metal oxide buffer layers are presented in detail, based on basic commercially available materials and tools, to achieve well-engineered tandem (multi-junction) solution-processed organic solar cells. The buffer layers have appropriate energy levels for electrical selectivity of anode and cathode electrodes, and they are highly stable and chemically compatible with processing of solution-based polymer solar cells. To demonstrate the engineering steps of multi-junction devices, the PCE10:PC70BM blend is used as the active layer for all subcells. Then, to improve the power conversion efficiency of the single-junction photovoltaic device, PCE10:PC70BM blend is used in combination with DPPx:PC70BM with different absorption spectra for bottom and top subcell active layers. An optimized series tandem device with 10.6% power conversion efficiency is demonstrated. Generally, the device structures reported here can also be used for other types of optoelectronic devices, such as light emitting diodes and photodetectors. Full article

Based on experimental results, this theoretical study presents a new approach for investigating polymers’ solar cells. P-type PZT:C1 and N-type PBDB:T were used to construct a blend for use as a photoactive layer for the proposed all-polymer solar cell. Initially, an architecture of an ITO/PEDOT:PSS/PBDB:T/PZT:C1/PFN-Br/Ag all-polymer solar device calibrated with experimental results achieved a PCE of 14.91%. A novel inverted architecture of the same solar device, proposed for the first time in this paper, achieved a superior PCE of 19.92%. Furthermore, the optimization of the doping of the transport layers is proposed in this paper. Moreover, the defect density and the thickness of the polymer are studied, and a PCE of 22.67% was achieved by the optimized cell, which is one of the highest PCEs of polymer solar devices. Finally, the optimized polymer solar cell showed good stability amidst temperature variations. This theoretical study sheds light on the inverted structure of all-polymer solar devices. Full article