Search Results (684)

In this study, multicomponent PLA-based biocomposites were developed. In particular, both native fibrous cellulose and cellulose with modified morphology obtained through ball milling treatments were incorporated into the polyester matrix in combination with an oligomeric plasticizer, specifically a lactic acid oligomer (OLA). The resulting materials were analyzed in terms of their morphology, thermal and mechanical properties over time, water vapor permeability, and degradation under soil burial conditions in comparison to neat PLA and unplasticized PLA/cellulose composites. The cellulose phase significantly affected the mechanical properties and enhanced their long-term stability, addressing a common limitation of PLA/plasticizer blends. Additionally, water vapor permeability increased in all composites. Finally, the ternary systems exhibited a significantly higher degradation rate in soil burial conditions compared to PLA, evidenced by larger weight loss and reduction in the molecular weight of the PLA phase. The degradation rate was notably influenced by the morphology of the cellulose phase. Full article

The inferior electrical conductivity and elevated hardness of AgSnO₂ electrical contact materials have impeded their development. To investigate the effects of Co, Bi, and La doping on the stability and electrical properties of AgSnO₂, this study established interfacial models of doped AgSnO₂ based on first-principles calculations initiated from the atomic structures of constituent materials, subsequently computing electronic structure parameters. The results indicate that doping effectively enhances the interfacial stability and bonding strength of AgSnO₂ and thereby predicted improved electrical contact performance. Doped SnO₂ powders were prepared experimentally using the sol–gel method, and AgSnO₂ contacts were fabricated using high-energy ball milling and powder metallurgy. Testing of wettability and electrical contact properties revealed reductions in arc energy, arcing time, contact resistance, and welding force post-doping. Three-dimensional profilometry and scanning electron microscopy (SEM) were employed to characterize electrical contact surfaces, elucidating the arc erosion mechanism of AgSnO₂ contact materials. Among the doped variants, La-doped electrical contact materials exhibited optimal performance (the lowest interfacial energy was 1.383 eV/Ų and wetting angle was 75.6°). The mutual validation of experiments and simulations confirms the feasibility of the theoretical calculation method. This study provides a novel theoretical method for enhancing the performance of AgSnO₂ electrical contact materials. Full article

The uniform distribution of APIs is essential in tablet formulations, particularly in direct compression, where powder blending is the only means of ensuring dose homogeneity. This study evaluated the influence of three mixing techniques—V-type mixer, planetary ball mill, and vibratory ball mill—on the physical properties and content uniformity of naproxen sodium tablets. Blends consisting of naproxen sodium, cellulose, PVP, calcium carbonate, and magnesium stearate were prepared under varied mixing intensities and characterized in terms of flowability, compressibility, and particle size distribution. The resulting tablets were analyzed for weight, thickness, hardness, friability, and API content using a simplified bypass HPLC method. The V-type mixer yielded tablets with the most consistent weight and thickness, despite the poorest blend flow properties. Vibratory milling produced the hardest tablets and best API content uniformity, although high-energy processing introduced variability at longer mixing times. The analytical method proved fast and robust, allowing for reliable API quantification without full chromatographic separation. These findings underscore the need to balance mechanical blending energy with formulation properties and support the use of streamlined analytical strategies in pharmaceutical development. Full article

Ball-end milling cutters are normally used for complex surface machining. During the milling process, the tool posture and cutting parameters of the ball-end milling cutters have a significant impact on chip formations and morphological changes. Based on the Cutter Workpiece Engagement (CWE) model, this study establishes a chip flow model for ball-end milling cutters with consideration of the tool posture variation. The machining experiments of Ti-6Al-4V with a 15° inclined plane and different feed directions were carried out. The influence mechanism of time-varying tool posture on chip formation was systematically investigated. The results reveal an interaction between the chip flow direction and the cutting velocity direction. The included angle between the chip flow directions at the maximum and minimum contact points in the CWE area affects the degree of chip curling, with a smaller angle leading to weaker curling. This research provides a theoretical foundation for the optimization of posture parameters of ball-end milling cutters and expounds on the influence of the chip flow angle on chip deformation. Full article

Mechanochemical and transition-metal-catalyzed reactions of alkynes, exhibiting significant advantages like short reaction time, solvent-free, high yield and good selectivity, were considered to be green and sustainable pathways to access functionalized molecules and obtained increasing attention due to the superiorities of mechanochemical processes and the reactivities of alkynes. The ball milling and CuI-catalyzed Sonogashira coupling of alkyne and aryl iodide avoided the use of common palladium catalysts. The mechanochemical Rh(III)- and Au(I)-catalyzed C–H alkynylations of indoles formed the 2-alkynylated and 3-alkynylated indoles selectively. The mechanochemical and copper-catalyzed azide-alkyne cycloaddition (CuAAC) between alkynes and azides were developed to synthesize 1,2,3-triazoles. Isoxazole could be formed through ball-milling-enabled and Ru-promoted cycloaddition of alkyne and hydroxyimidel chloride. In this review, the generation of mechanochemical and transition-metal-catalyzed reactions of alkynes was highlighted. Firstly, the superiority and application of transition-metal-catalyzed reactions of alkynes were briefly introduced. After presenting the usefulness of green chemistry and mechanochemical reactions, mechanochemical and transition-metal-catalyzed reactions of alkynes were classified and demonstrated in detail. Based on different kinds of reactions of alkynes, mechanochemical and transition-metal-catalyzed coupling, cycloaddition and alkenylation reactions were summarized and the proposed reaction mechanisms were disclosed if available. Full article

The permanent magnet integrated motor (PMIM) for ball mills has the problems of difficult assembly and poor air gap uniformity adjustment due to the magnetic pull force in the conventional magnetic assembly. In this study, a non-magnetic assembly technology based on the installation of a permanent magnet after assembly was first proposed, and the analytical models of conventional magnetic assembly and non-magnetic assembly were established. On this basis, combined with the finite element method, the mechanical performance difference between the two assembly methods in the assembly, lifting, and centering stages were compared and analyzed. In addition, a device for adjusting the air gap was designed for the non-magnetic assembly technology, and the stress and deformation of the structure of this device were analyzed. The results showed that the total assembly load by using the non-magnetic assembly technique was significantly reduced by 71.8%, the maximum stress in the assembly process was reduced by 66.3%, and the maximum deformation was reduced by 66.7%, which significantly reduced the difficulty of assembly. Finally, a 210 W permanent magnet integrated motor for ball mills was designed and successfully assembled, which proves the effectiveness of the assembly technology. Full article

Fe and Cu powders were mixed at a 50:50 ratio. Then, Fe-Cu alloys were prepared using the ball milling technique with different milling times of 6, 12, 18, 24, 30, 36, and 42 h. The crystalline structure was analyzed using X-ray diffraction (XRD), and it was found that the optimum milling time was 30 h. The homogeneity of the Fe and Cu elements in the Fe–Cu alloys was analyzed using the scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM–EDX) mapping technique. Additionally, the crystal orientation of the Fe–Cu alloys was investigated using transmission electron microscopy (TEM). To fabricate the cathode for nitrate removal via electrolysis, an Fe–Cu alloy milled for 30 h was deposited onto a copper substrate using mechanical milling, then annealed at 800 °C. A pulsed DC electrolysis method was developed to test the nitrate removal efficiency of the Fe–Cu-coated cathode. The anode used was an Al sheet. The synthesized wastewater was prepared from KNO₃. Nitrate removal experiments from the synthesized wastewater were performed for durations of 0–4 h. The results show that the nitrate removal efficiency at 4 h was 96.90% compared to 74.40% with the Cu cathode. Full article

Magnesium-containing multi-principal element alloys (MPEAs) are promising for lightweight applications due to their low density, high specific strength, and biocompatibility. This study examines two Mg-Ti-Zn alloy compositions, equal molar MgTiZn (TZ) and Mg₄TiZn (4TZ), synthesized via ball milling followed by spark plasma sintering, focusing on their microstructures and corrosion behaviors. X-ray diffraction and transmission electron microscopy revealed the formation of intermetallic phases, including Ti₂Zn and Mg₂₁Zn₂₅ in TZ, while 4TZ exhibited a predominantly Mg-rich phase. Potentiodynamic polarization and immersion tests in 0.1 M NaCl solution showed that both alloys had good corrosion resistance, with values of 3.65 ± 0.65 µA/cm² for TZ and 4.58 ± 1.64 µA/cm² for 4TZ. This was attributed to the formation of a TiO₂-rich surface film in the TZ, as confirmed by X-ray photoelectron spectroscopy (XPS), which contributed to enhanced passivation and lower corrosion current density. Both alloys displayed high hardness, 5.5 ± 1.0 GPa for TZ and 5.1 ± 0.9 GPa for 4TZ, and high stiffness, with Young’s modulus values of 98.2 ± 11.2 GPa for TZ and 100.8 ± 9.6 GPa for 4TZ. These findings highlight the potential of incorporating Ti and Zn via mechanical alloying to improve the corrosion resistance of Mg-containing MPEAs and Mg-based alloys. Full article

This study presents a novel flake powder metallurgy approach for fabricating Al/CNT composites, combining the dual-matrix (DM) method with shift-speed ball milling (SSBM) to optimize mechanical performance. Samples prepared via DM-SSBM were systematically compared to those produced by conventional high-speed ball milling (HSBM), single-stage SSBM, and dual-matrix (DM) routes. Tensile testing revealed that the DM₁MR₅₀-SSBM composite achieved a superior balance of strength and ductility, with an ultimate tensile strength of ~267 MPa, elongation of ~9.9%, and the highest energy absorption capacity (~23.4 MJ/m³) among all tested samples. In contrast, the HSBM sample, while achieving the highest tensile strength (~328 MPa), exhibited limited elongation (~4.7%), resulting in lower overall toughness. The enhanced mechanical response of the DM-SSBM composites is attributed to improved CNT dispersion, refined cold-welding interfaces, and pure Al matrix softness, which together facilitate superior load transfer and hinder crack propagation under tensile stress. In the final consolidated state, aluminum forms a continuous matrix embedding the CNTs, justifying the use of the term “aluminum matrix” to describe the composite structure. These findings highlight the DM-SSBM approach as a promising method for developing lightweight, high-toughness aluminum composites suitable for energy-absorbing structural applications. Full article

In this study, we investigate the environmental stability of the sulfide-based argyrodite solid electrolyte Li₆PS₅Cl₀.₅Br₀.₅, a promising candidate for all-solid-state lithium batteries due to its high ionic conductivity and favorable mechanical properties. Despite its potential, the material’s sensitivity to ambient air humidity presents challenges for large-scale battery manufacturing. Moisture exposure leads to performance degradation and the release of toxic hydrogen sulfide (H₂S) gas, raising concerns for workplace safety. The objectives of this study are to validate the electrolyte synthesis process, evaluate the effects of air humidity exposure on its reactivity and ionic conductivity, and establish a standardized protocol for assessing environmental stability. We report a synthesis method based on ball milling and heat treatment that achieves an ionic conductivity of 2.11 mS/cm, along with a fundamental study incorporating modeling and formulation approaches to evaluate the electrolyte’s environmental stability. Furthermore, we introduce a simplified testing method for assessing environmental stability, which may serve as a benchmark protocol for the broader class of argyrodite solid electrolytes. Full article

This study examines the mechanical and microstructural properties of graphene-reinforced AA2219 composites developed for hydrogen storage tank inner liner applications. A novel processing route combining high-energy ball milling, ultrasonic-assisted stir casting, and squeeze casting was used to achieve homogeneous dispersion of 0.5 wt.% graphene nanoplatelets and minimise agglomeration. The composites were subjected to T6 and T8 ageing treatments to optimize their properties. Microstructural analysis revealed refined grains, uniform Al₂Cu precipitate distribution, and stable graphene retention. Mechanical testing showed that the as-cast composite exhibited a UTS of 308.6 MPa with 13.68% elongation. After T6 treatment, the UTS increased to 353.6 MPa with an elongation of 11.24%. T8 treatment further improved the UTS to 371.5 MPa, with an elongation of 8.54%. Hardness improved by 46%, from 89.6 HV (as-cast) to 131.3 HV (T8). Fractography analysis indicated a shift from brittle to ductile fracture modes after heat treatment. The purpose of this work is to develop lightweight, high-strength composites for hydrogen storage applications. The novelty of this study lies in the integrated processing approach, which ensures uniform graphene dispersion and superior mechanical performance. The results demonstrate the suitability of these composites for advanced aerospace propulsion systems. Full article

To improve the combustion performance of boron powder, a method was developed for synthesizing boron–magnesium–titanium (B-Mg-Ti) ternary composite powders with controlled metal content. Boron–magnesium (B-Mg) base materials were first prepared via electrical explosion, followed by the incorporation of titanium powder at varying mass fractions (1 wt.%, 3 wt.%, 5 wt.%, and 7 wt.%) through mechanical ball milling. Field emission scanning electron microscopy (FE-SEM) revealed that the addition of titanium promoted a more uniform dispersion of magnesium within the boron agglomerates. Moreover, nanoscale titanium particles were observed to be embedded on the particle surfaces, confirming successful microscale composite formation. Particle size distribution was measured using a Malvern 3000 laser particle size analyzer, and results showed that the particle size of the ternary composites decreased gradually with increasing titanium content. Specific surface area was determined via the Brunauer–Emmett–Teller (BET) method, with all samples exhibiting values greater than 15 m²/g, indicating good surface reactivity. Furthermore, the rheological behavior of the B-Mg-Ti composite powders, when combined with terminal hydroxyl polybutadiene (HTPB)—a typical binder in solid propellants—was evaluated. Viscosity measurements were conducted using a rotational rheometer at constant temperatures of 20 °C and 70 °C. The results demonstrated a marked decrease in viscosity with increasing titanium content, suggesting that titanium incorporation enhances the flowability of the composite powders. This study systematically evaluated the influence of titanium content on the structural and physicochemical properties of B-Mg-Ti composite powders, thereby providing a valuable experimental foundation for the optimized design of boron-based combustion systems and the enhancement of their processing and application performance. Full article

The development of robust and scalable tablet manufacturing methods remains a key objective in pharmaceutical technology, especially when dealing with active pharmaceutical ingredients (APIs) and excipients that exhibit suboptimal processing properties. This study evaluated two alternative manufacturing strategies for tablets containing sodium naproxen (20%, API), dolomite (65%, sustainable mineral filler), cellulose (7%), polyvinylpyrrolidone (5%, binder), and magnesium stearate (3%, lubricant). The direct compression method used a vibrating ball mill (SPEX SamplePrep 8000M), while the indirect method employed wet granulation using a pan granulator at different inclination angles. Physical properties of raw materials and granules were assessed, and final tablets were evaluated for mass, thickness, mechanical resistance, abrasiveness, and API content uniformity. Direct compression using vibratory mixing for 5–10 min (DT2, DT3) resulted in average tablet masses close to the target (0.260 g) and improved reproducibility compared to a reference V-type blender. Wet granulation produced tablets with the lowest abrasiveness (<1.0%) and minimal variability in dimensions and API content. The best uniformity (SD < 0.5%) was observed in batch IT2. Overall, vibratory mixing proved capable of achieving tablet quality comparable to that of wet granulation, while requiring fewer processing steps. This highlights its potential as an efficient and scalable alternative in solid dosage manufacturing. Full article

The manufacture of barium sulfide or barium salts (BaS, BaCl₂, Ba (OH)₂, among others) requires high-purity barite ores (>90%). In this study, a new method to produce barium sulfide from low-grade barite ores (60% purity) is proposed. The method involves gravitational concentration of barite ore on a shaking table followed by mechanical activation of the barite concentrate with metallurgical coke in a ball mill. The mechanically activated mixture undergoes carbothermic reduction with an argon flow, resulting in the conversion of barite concentrate into barium sulfide. Gravitational concentration studies conducted using a shaking table demonstrated that, upon optimizing key operational parameters—namely, the wash-water flow rate, length, stroke frequency, the splitter positions of the concentrate, middlings, and tailings—a barite concentrate with a purity exceeding 95% BaSO₄ was successfully achieved. Mechanical activation of the barite/coal mixture lowered the initial temperature of the carbothermic reduction from 1100 K to 990 K, enabling complete conversion of barite to BaS, as confirmed by thermogravimetric curves and XRD analysis. Furthermore, the activation energy during the carbothermic reduction ranged from 300 to 500 kJ/mol, suggesting a complex reduction process of barite with metallurgical coke that is difficult to represent by a single reaction. Full article

To enhance the performance of polyurethane foams, fillers are often incorporated into the matrix. However, the interaction between the filler and the polyurethane matrix is crucial for achieving the desired property improvements. Therefore, surface modification of the fillers plays a vital role in optimizing this interaction. The current study aims to activate the surface of expanded vermiculite and perlite with dextrin to incorporate additional functional groups on the surface of the fillers via the ball-milling process, thereby improving the reaction with a polymer matrix. Applied surface activation with dextrin resulted in the formation of dextrin-Si-O-Si-dextrin linkages in the fillers, allowing for a maximum improvement of 11% and 9% in water absorption, as well as slightly positive changes in the water contact angle of polyurethane foam with dextrin-activated perlite and vermiculite, respectively, compared to non-activated fillers. It also resulted in noticeable differences in the foaming times and viscosity of the premixes, affecting the structure of rigid polyurethane foam composites. Compared to non-activated perlite and vermiculite filler polyurethane foam composites, the dynamic viscosity of polyurethane foam composites with dextrin-activated perlite and vermiculite reduced maximally 16 and 21 times, respectively. At the same time, the closed cell content increased, resulting in lower thermal conductivity values up to a 7.5 wt.% filler concentration. In addition, a rise in mechanical performance was also achieved. Compressive strength increased by a maximum of 61% and 71%, while tensile strength increased by a maximum of 36% and 20% for polyurethane foam composites with dextrin-activated perlite and vermiculite, respectively. Full article