Search Results (345)

New-generation geostationary meteorological satellite radiometric imagers widely employ multi-column redundant long-linear-array detectors, for which the Best Detector Selection (BDS) strategy is crucial for enhancing the quality of remote sensing data. Addressing the limitation of current BDS methods that often rely on a single metric and thus fail to fully exploit the detector’s comprehensive performance, this paper proposes a detector evaluation method based on a modified Z-score. This method systematically categorizes detector metrics into three types: positive, negative, and uniformity. It introduces, for the first time, spectral response deviation (SRD) as an effective quantitative measure for the Spectral Response Function (SRF) and employs a robust normalization strategy using the Interquartile Range (IQR) instead of standard deviation, enabling multi-dimensional detector evaluation and selection. Validation using laboratory data from the FY-4C/AGRI long-wave infrared band demonstrates that, compared to traditional single-metric optimization strategies, the best detectors selected by our method show significant improvement across multiple performance indicators, markedly enhancing both data quality and overall system performance. The proposed method features low computational complexity and strong adaptability, supporting on-orbit real-time detector optimization and dynamic updates, thereby providing reliable technical support for high-quality processing of remote sensing data from geostationary meteorological satellites. Full article

Predicting internal quality parameters, such as Brix and water content, of apples, is essential for quality control. Existing near-infrared (NIR) and hyperspectral imaging (HSI)-based techniques have limited applicability due to their dependence on equipment and environmental sensitivity. In this study, a transportable quality assessment system was proposed using spatiotemporal domain analysis with long-wave infrared (LWIR)-based thermal diffusion phenomics, enabling non-destructive prediction of the internal Brix of apples during transport. After cooling, the thermal gradient of the apple surface during the cooling-to-equilibrium interval was extracted. This gradient was used as an input variable for multiple linear regression, Ridge, and Lasso models, and the prediction performance was assessed. Overall, 492 specimens of 5 cultivars of apple (Hongro, Arisoo, Sinano Gold, Stored Fuji, and Fuji) were included in the experiment. The thermal diffusion response of each specimen was imaged at a sampling frequency of 8.9 Hz using LWIR-based thermal imaging, and the temperature changes over time were compared. In cross-validation of the integrated model for all cultivars, the coefficient of determination (R²_cv) was 0.80, and the RMSEcv was 0.86 °Brix, demonstrating stable prediction accuracy within ±1 °Brix. In terms of cultivar, Arisoo (Cultivar 2) and Fuji (Cultivar 5) showed high prediction reliability (R²_cv = 0.74–0.77), while Hongro (Cultivar 1) and Stored Fuji (Cultivar 4) showed relatively weak correlations. This is thought to be due to differences in thermal diffusion characteristics between cultivars, depending on their tissue density and water content. The LWIR-based thermal diffusion analysis presented in this study is less sensitive to changes in reflectance and illuminance compared to conventional NIR and visible light spectrophotometry, as it enables real-time measurements during transport without requiring a separate light source. Surface heat distribution phenomics due to external heat sources serves as an index that proximally reflects changes in the internal Brix of apples. Later, this could be developed into a reliable commercial screening system to obtain extensive data accounting for diversity between cultivars and to elucidate the effects of interference using external environmental factors. Full article

Accurate modelling of reflection, transmission, absorption, and emission at material interfaces is essential for infrared imaging, rendering, and the simulation of optical and sensing systems. This need is particularly pronounced across the short-wave to long-wave infrared (SWIR–LWIR) spectrum, where many materials exhibit dispersion- and wavelength-dependent attenuation described by complex refractive indices. In this work, we introduce a unified formulation of the full Fresnel equations that directly incorporates wavelength-dependent complex refractive-index data and provides physically consistent interface behaviour for both dielectrics and conductors. The approach reformulates the classical Fresnel expressions to eliminate sign ambiguities and numerical instabilities, resulting in a stable evaluation across incidence angles and for strongly absorbing materials. We demonstrate the model through spectral-rendering simulations that illustrate realistic reflectance and transmittance behaviour for materials with different infrared optical properties. To assess its suitability for thermal-infrared applications, we also compare the simulated long-wave emission of a heated glass sphere with measurements from a LWIR camera. The agreement between measured and simulated radiometric trends indicates that the proposed formulation offers a practical and physically grounded tool for wavelength-parametric interface modelling in infrared imaging, supporting applications in spectral rendering, synthetic data generation, and infrared system analysis. Full article

Fourier transform infrared (FTIR) spectroscopy-based gas remote sensing has been widely applied for long-range atmospheric composition analysis. However, when deployed for longwave infrared methane detection, spectral features of methane are significantly interfered by water vapor variations at the edge of atmospheric window, which compromises detection performance. To address the spectral fitting degradation caused by relative changes between methane and water vapor signals, this study incorporates temperature, relative humidity, and sensing distance into the cost function, establishing a continuous optimization space with concentration path lengths (CLs) as variables, which are the product of the concentration and path length. A hybrid differential evolution and Levenberg–Marquardt (D-LM) algorithm is developed to enhance parameter estimation accuracy. Combined with a three-layer atmospheric model for real-time reference spectrum generation, the algorithm identifies the optimal spectral combination that provides the best match to the measured data. Algorithm performance is validated through two experimental configurations: Firstly, adaptive detection using synthetic spectra covering various humidity–methane concentration combinations is conducted; simulation results demonstrate that the proposed method significantly reduces the mean squared error (MSE) of fitting residuals by 95.8% compared to the traditional LASSO method, effectively enhancing methane spectral feature extraction under high-water-vapor conditions. Then, a continuous monitoring of controlled methane releases over a 500 m open path under high-outdoor-humidity conditions is carried out to validate outdoor performance of the proposed algorithm; field measurement analysis further confirms the method’s robustness, achieving a reduction in fitting residuals of approximately 57% and improving spectral structure fitting. The proposed approach provides a reliable technical pathway for adaptive gas cloud detection under complex atmospheric conditions. Full article

We present an inverse designed metalens for long-wave infrared (LWIR) imaging tailored to consumer and Internet of Things (IoT) platforms. Conventional LWIR optics either rely on costly specialty materials or suffer from low efficiency and narrow fields of view (FoV), limiting scalability. Our approach integrates adjoint-based inverse design with fabrication-aware constraints and a cone-shaped source model that efficiently captures oblique incidence during optimization. The resulting multi-level metalens achieves a wide FoV up to 100° while maintaining robust focusing efficiency and stable angle-to-position mapping on low-power $4\times 4$ microbolometer arrays representative of edge devices. We further demonstrate application-level imaging on $4\times 4$ microbolometer arrays, showing that the proposed metalens delivers a substantially wider FoV than a commercial narrow FoV lens while meeting low-resolution, low-cost, and low-power constraints for edge LWIR modules. By eliminating bulky multi-element stacks and reducing cost and form factor, the proposed design provides a practical pathway to compact, energy-efficient LWIR modules for consumer applications such as occupancy analytics, smart-building automation, mobile sensing, and outdoor fire surveillance. Full article

Polarization beam combining (PBC) is an important technology for enhancing laser brightness. The conventional bulk polarization beam combiners are Brewster plates and birefringent polarization prisms. However, in the mid- and long-wave infrared range, the beam combining performance is limited by the transmission and birefringent coefficient of the available materials. In this paper, a polarization beam combiner based on a reflection metasurface was proposed. The phases of incident beams with orthogonal linear polarizations were individually manipulated by the side lengths of the rectangular silicon pillar. A metasurface polarization beam combiner operating band was designed and fabricated. When the two beams at 4.6 μm with orthogonal linear polarizations were incident on the metasurface at angles of −13.3° and 13.3°, respectively, they were reflected in the 0°-direction. The overall beam combining efficiency was 88.9%. When both of the quantum cascade lasers used in the experiments were in the fundamental transverse Gaussian mode, the measured beam quality factors M² of the combined beam were 1.21 and 1.14 along the fast and slow axes, respectively. Both simulation and experimental results demonstrated that the proposed metasurface was an efficient polarization beam combiner with negligible wavefront distortion. It is a promising alternative to traditional bulk optics for the mid- and long-wave infrared. Full article

Fused deposition modeling (FDM) is one of the most widely adopted additive manufacturing (AM) technologies due to its accessibility and versatility; however, ensuring process reliability and product quality remains a significant challenge. This work introduces a novel methodology to evaluate the fidelity of programmed extruder head trajectories and speeds against those executed during the printing process. The approach integrates infrared thermography and image processing. A type-V ASTM D638-14 polylactic acid (PLA) specimen was fabricated using 16 layers, and its G-code data were systematically compared with kinematic variables extracted from long-wave infrared (LWIR) thermal images. The results demonstrate that the approach enables the detection of deviations in nozzle movement, providing valuable insights into layer deposition accuracy and serving as an early indicator for potential defect formation. This thermal image–based monitoring can serve as a non-invasive tool for in situ quality control (QC) in FDM, supporting process optimization and improved reliability of AM polymer components. These findings contribute to the advancement of smart sensing strategies for integration into industrial additive manufacturing workflows. Full article

This study introduces a controlled laboratory setup for hyperspectral longwave infrared (LWIR) imaging of soils, designed to bridge the gap between laboratory measurements and remote sensing observations. A Fourier-transform hyperspectral LWIR imaging spectrometer (Telops Hyper-Cam LW) was employed, together with a specialized heating plate, rigorous calibration protocols, and a Spatial Averaging Before Blackbody Fitting (SABBF) method to enable accurate LWIR indoor measurements. Unlike established laboratory techniques that measure reflectance and calculate emissivity indirectly, this setup enables direct passive measurement of soil emissivity, replicating airborne and spaceborne LWIR measurements of the surface. The emissivity spectra of 12 variable soil samples obtained with the lab setup were compared and validated based on LWIR Hyper-Cam LW spectra acquired under outdoor conditions, then were subsequently analyzed to determine the mineral composition of each sample. Spectral features and indices were used to estimate the relative content of quartz, clay minerals, and carbonates, from the most to least abundant. The results demonstrate that the laboratory-based setup preserves spectral fidelity while offering improved repeatability, scheduling flexibility, and reduced dependence on weather. Beyond replicating outdoor measurements, this controlled setup is easy to install and provides a reproducible framework for LWIR soil spectroscopy that could be considered for standard laboratory protocols, enabling reliable mineral identification, calibration/validation of airborne and satellite LWIR data, and broader applications in soil monitoring and environmental remote sensing. Full article

Collisions with fallen pedestrians pose a lethal challenge to current advanced driver-assistance systems. This paper introduces and quantitatively validates the Advanced Falling Object Detection System (AFODS), a novel safety framework designed to mitigate this risk. AFODS architecturally integrates long-wave infrared, near-infrared stereo and ultrasonic sensors, processed through a novel artificial intelligence pipeline that combines YOLOv7-Tiny for object detection with a recurrent neural network for proactive threat assessment, thereby enabling the system to predict falls before they are complete. In a rigorous controlled study using simulated adverse conditions, AFODS achieved a 98.2% detection rate at night, a condition where standard systems fail. This paper details the system’s ISO 26262-aligned architecture and validation results, proposing a framework for a new benchmark in active vehicle safety, demonstrated under controlled test conditions. Full article

Integrating metasurface-based polarizing filters atop photodetectors enables the expansion of detection capabilities from intensity to polarization, offering significant potential for applications requiring high-precision discrimination in scientific, industrial, and defense sectors. However, such metasurfaces often introduce optical efficiency losses. Here, we present a long-wave infrared (8.6 μm) circularly polarized photodetector capable of direct chiral discrimination, eliminating the need for additional optical components. The polarization selectivity arises from Guided-Mode resonances (GMRs) excited by two horizontally offset right-trapezoidal unit cells within a chiral metasurface. This design exhibits a pronounced transmittance contrast (~100%) between left circularly polarized light (LCP) and right circularly polarized light (RCP) while maintaining fabrication simplicity via a conventional single-step lithographic process. The proposed detector is expected to achieve high-dimensional physical characterization by resolving polarization-encoded vectorial information, demonstrating enhanced performance in complex environments. Full article

Land surface temperature (LST) is a critical variable for understanding energy exchanges and water balance at the Earth’s surface, as well as for calculating turbulent heat flux and long-wave radiation at the surface–atmosphere interface. Remote sensing techniques, particularly using satellite platforms like Landsat 8 OLI/TIRS and Sentinel-2A, have facilitated detailed LST mapping. Sentinel-2 offers high spatial and temporal resolution multispectral data, but it lacks thermal infrared bands, which Landsat 8 can provide a 30 m resolution with less frequent revisits compared to Sentinel-2. This study employs Sentinel-2 spectral indices as independent variables and Landsat 8-derived LST data as the target variable within a machine-learning framework, enabling LST prediction at a 10 m resolution. This method applies grid search-based hyperparameter-tuned machine learning algorithms—Random Forest (RF), Gradient Boosting Machine (GBM), Support Vector Machine (SVM), and k-Nearest Neighbours (kNN)—to model complex nonlinear relationships between the spectral indices (NDVI, NDWI, NDBI, and BSI) and LST. Grid search, combined with cross-validation, enhanced the model’s prediction accuracy for both pre- and post-monsoon seasons. This approach surpasses earlier methods that either employed untuned models or failed to integrate Sentinel-2 data. This study demonstrates that capturing urban thermal dynamics at fine spatial and temporal scales, combined with tuned machine learning models, can enhance the capability of urban heat island monitoring, climate adaptation planning, and sustainable environmental management models. Full article

The growing demand for compact, low-power infrared (IR) sensors necessitates advanced solutions for on-chip spectral selectivity, particularly for integration with Thermal Metal-Oxide-Semiconductor (TMOS) devices. This paper investigates the design and analysis of CMOS-compatible metal–insulator–metal (MIM) metamaterial absorbers tailored for selective absorption in the long-wave infrared (LWIR) region. We present a design methodology utilizing an equivalent-circuit model, which provides intuitive physical insight into the absorption mechanism and significantly reduces computational costs compared to full-wave electromagnetic simulations. An important rule in this design methodology is demonstrating how the resonance wavelength of these absorbers can be precisely tuned across the LWIR spectrum by engineering the geometric parameters of the top metallic patterns and, critically, by optimizing the dielectric substrate’s refractive index and thickness, which assist in designing small period MIM absorber units which are important in infrared thermal sensor pixels. Our results demonstrate that the resonance wavelength of these absorbers can be precisely tuned across the LWIR spectrum by engineering the geometric parameters of the top metallic patterns and by optimizing the dielectric substrate’s refractive index and thickness. Specifically, the selection of silicon as the dielectric material, owing to its high refractive index and low losses, facilitates compact designs with high-quality factors. The transmission line model provides intuitive insight into how near-perfect absorption is achieved when the absorber’s input impedance matches the free-space impedance. This work presents a new approach for the methodology of designing MIM absorbers in the mid-infrared and long-wave infrared (LWIR) regions, utilizing the intuitive insights provided by equivalent circuit modeling. This study validates a highly efficient design approach for high-performance, spectrally selective MIM absorbers for LWIR radiation, paving the way for their monolithic integration with TMOS sensors to enable miniaturized, cost-effective, and functionally enhanced IR sensing systems. Full article

Remote sensing of wildland fires has become an integral part of fire science. Airborne sensors provide high spatial resolution and can provide high temporal resolution, enabling fire behavior monitoring at fine scales. Fire agencies frequently use airborne long-wave infrared (LWIR) imagery for fire monitoring and to aid in operational decision-making. While tactical remote sensing systems may differ from scientific instruments, our objective is to illustrate that operational support data has the capacity to aid scientific fire behavior studies and to facilitate the data analysis. We present an image processing algorithm that automatically delineates active fire edges in tactical LWIR orthomosaics. Several thresholding and edge detection methodologies were investigated and combined into a new algorithm. Our proposed method was tested on tactical LWIR imagery acquired during several fires in California in 2020 and compared to manually annotated mosaics. Jaccard index values ranged from 0.725 to 0.928. The semi-automated algorithm successfully extracted active fire edges over a wide range of image complexity. These results contribute to the integration of infrared fire observations captured during firefighting operations into scientific studies of fire spread and support landscape-scale fire behavior modeling efforts. Full article

High-speed impact is a critical mechanism for structural damage. The infrared signatures generated during fragment formation provide essential data for damage assessment, protective system design, and target identification. This study investigated an aluminum alloy blunt projectile penetrating a target plate by employing smoothed particle hydrodynamics to simulate the debris ejection thermal and infrared properties. The infrared signatures of the debris clouds were calculated using Mie scattering theory under a spherical particle approximation. The reverse Monte Carlo methodology was applied to solve the radiative transfer equations and quantify the infrared emission characteristics. The infrared radiation characteristics of the debris cloud were investigated for projectile impact velocities of 800, 1000, and 1200 m/s. The results showed that the anterior debris regions reached peak temperatures of approximately 1200 K, with a temperature rise of 150–200 K per 200 m/s velocity increase behind the target. The medium-wave (3–5 μm) infrared intensity of the debris cloud was higher than the long-wave (8–12 μm) infrared intensity. The development of debris clouds enhanced the dispersion effect and slowed the increase in infrared radiation intensity in the same time interval. This study provides theoretical foundations for the dynamic infrared radiation characteristics of fragments generated by high-velocity projectile impacts. The infrared radiation characteristics within typical spectral bands can be utilized to assess hit probability and kill effectiveness. Full article

In urban heat islands with sun-exposed roofs, the cooling potential of unfinished attics is often insufficient. Attics and the adjacent floor often overheat and do not cool sufficiently during tropical nights. Because of heritage-preservation requirements and limited structural reserve in historic roof constructions, it is often not possible to install heat-dissipating photovoltaic modules or add a superimposed cold-roof assembly above the existing roof skin. A possible solution is ‘infrared (IR) shading’, which uses interior IR-shading elements to shield long-wave radiation from the solar-heated roof skin. The research had two goals: (i) develop and evaluate lightweight IR-shading elements that can be reversibly mounted at rafter level on the attic side; and (ii) investigate how rafter-field ventilation can remove heat from the IR-shading elements. Full article