Search Results (381)

The lodging resistance of rice is a prerequisite for ensuring yield and rice quality. An in-depth analysis of key traits affecting rice lodging resistance is crucial for guiding the cultivation of excellent rice varieties and field production. Given consumer demand for high-quality rice and frequent extreme weather conditions, this study focused on six high-quality conventional rice varieties and compared the main stem internode physical traits, stem and sheath plumpness traits, main stem mechanical properties, yield-related traits, and panicle characteristics of the plants based on field phenotype measurements. Among them, three varieties showed lodging resistance in the field, while the other three varieties all experienced varying degrees of lodging susceptibility. The results showed that lodging-resistant varieties exhibited a more reasonable internode structure, lower plant height, gravity center height, and relative gravity center height, as well as shorter and thicker second internodes (N2). Additionally, they had higher sheath phimosis degree, greater bending stress, internode-breaking moment, and plant-breaking moment, along with a lower lodging index compared to lodging-susceptible varieties. Specifically, lodging-resistant varieties had 0.83–9.61% lower plant height, 4.11–16.10% lower gravity center height, and 0.09–12.68% lower relative gravity center height than those of lodging-susceptible varieties. Their N2 internode length was 8.96–44.69% shorter, while stem and sheath weight ratios were 16.37–268.58% and 8.27–165.01% higher than those of lodging-susceptible varieties, respectively. At the same time, lodging-resistant varieties exhibit the ability to stabilize yield while reducing their own risk of lodging by increasing effective panicles and reducing single panicle weight. In addition, NX42, LD3, and SY17 were ultimately evaluated as low-risk lodging varieties in this study. This study aims to address the lodging problem of high-quality conventional rice and analyze the key mechanisms underlying its lodging resistance. The research provides important theoretical support for genetic improvement of high-quality conventional rice. Full article

Sewer systems are essential for sustainable infrastructure management, influencing environmental, social, and economic aspects. However, sewer network capacity is under significant pressure, with many systems overwhelmed by challenges such as climate change, ageing infrastructure, and increasing inflow and infiltration, particularly through groundwater infiltration (GWI). Current research in this area has primarily focused on general sewer performance, with limited attention to high-resolution, spatially explicit assessments of sewer exposure to GWI, highlighting a critical knowledge gap. This study responds to this gap by developing a high-resolution GWI assessment. This is achieved by integrating fuzzy-analytical hierarchy process (AHP) with geographic information systems (GISs) and machine learning (ML) to generate GWI probability maps across the Dawlish region, southwest United Kingdom, complemented by sensitivity analysis to identify the key drivers of sewer network vulnerability. To this end, 16 hydrological–hydrogeological thematic layers were incorporated: elevation, slope, topographic wetness index, rock, alluvium, soil, land cover, made ground, fault proximity, fault length, mass movement, river proximity, flood potential, drainage order, groundwater depth (GWD), and precipitation. A GWI probability index, ranging from 0 to 1, was developed for each 1 m × 1 m area per season. The model domain was then classified into high-, intermediate-, and low-GWI-risk zones using K-means clustering. A consistency ratio of 0.02 validated the AHP approach for pairwise comparisons, while locations of storm overflow (SO) discharges and model comparisons verified the final outputs. SOs predominantly coincided with areas of high GWI probability and high-risk zones. Comparison of AHP-weighted GIS output clustered via K-means with direct K-means clustering of AHP-weighted layers yielded a Kappa value of 0.70, with an 81.44% classification match. Sensitivity analysis identified five key factors influencing GWI scores: GWD, river proximity, flood potential, rock, and alluvium. The findings underscore that proxy-based geospatial and machine learning approaches offer an effective and scalable method for mapping sewer network exposure to GWI. By enabling high-resolution risk assessment, the proposed framework contributes a novel proxy and machine-learning-based screening tool for the management of smart cities. This supports predictive maintenance, optimised infrastructure investment, and proactive management of GWI in sewer networks, thereby reducing costs, mitigating environmental impacts, and protecting public health. In this way, the method contributes not only to improved sewer system performance but also to advancing the sustainability and resilience goals of smart cities. Full article

In this paper, a novel venturi jet reactor is innovatively proposed for the process of hydrazine hydrate production using the urea method. In order to investigate the performance of this reactor in depth, we used the computational fluid dynamics method to optimize the design of the structure of the new venturi jet reactor based on the flow field condition, the degree of mixing uniformity, and the efficiency of the reactor using the component transport model. The results showed that the moderate increase of the distance of mixing tube to nozzle and nozzle diameter seven could help to improve the efficiency of the jet reactor; however, in terms of the mixing effect, the increase of the distance of mixing tube to nozzle led to the mixing effect to be enhanced and then weakened, while the increase in the nozzle diameter was not conducive to the full mixing of the two fluids. In addition, the effects of ratio of throat length to diameter and constriction angle on the efficiency of the jet reactor showed nonlinear characteristics, and the optimal values existed in the study range. Based on the above analysis, this paper determines the optimal range of structural parameters, i.e., the distance of mixing tube to nozzle of 7–13 mm, the nozzle outlet diameter of 5–7 mm, the ratio of throat length to diameter of 3–5, and the constriction angle of 30–40°, and the study provides guidance for the industrial application of the venturi jet reactor. Full article

Preferential flow in coal mining subsidence areas leads to shallow soil moisture loss, vegetation reducing and ecological degradation. However, the factors influencing the development of preferential flow remain unclear. This study analyzed the morphological characteristics of preferential flow using a staining tracer test in coal mining subsidence areas along the middle reaches of the Yellow River Basin. Characteristic parameters including the dye-stained area ratio, preferential flow ratio, length index, variation coefficient were comparatively evaluated under different initial soil moisture conditions. Results showed that shallow soils exhibited substrate flow, while preferential flow occurred in deeper soil layers below the matrix flow. As initial soil moisture increased, the extent of both substrate flow and preferential flow decreased. The dye-stained area ratio declined with increasing soil depth, and the relationship between dye-stained area and soil layer depth was best described by a cubic function. Higher initial soil moisture reduced maximum infiltration depth and length indices while increasing the coefficient of the stained pattern. Furthermore, a higher of initial soil water content corresponded to a lower preferential flow index. Overall, increased initial soil moisture may reduce the extent of preferential flow and the rapid infiltration of water into soil. These findings provides a basis for further hydrological studies in coal mining subsidence areas in arid and semi-arid regions and offer scientific support for ecological restoration efforts in mining areas. Full article

The topography of the flood path significantly influences the hydraulic characteristics of flood events, necessitating in-depth analysis to better understand the continuous dynamics during dam failure scenarios. These analyses are useful for the hydraulic evaluation of infrastructures downstream of a dam site. This study examined the effects of four distinct converging configurations of guide-banks on the propagation of unsteady flow in a rectangular channel. The configurations studied included trapezoidal and crescent side contractions, as well as trapezoidal and crescent barriers located at the channel’s center, each with varying lengths and widths. Numerical simulations using computational fluid dynamics (CFD) simulation were validated against experimental data from the literature. The results reveal that the flow experienced a depth increase upon encountering converging geometries, leading to the formation of a hydraulic jump and the subsequent upstream progression of the resulting wave. The width of the obstacles and contractions had a marked influence on the flow profile. Increased channel contraction led to a more pronounced initial water elevation rise when the flood flow encountered the topography, resulting in a deeper reflected wave that propagated upstream at less time. The reflected wave increased the water elevations up to 0.64, 0.72, and 0.80 times the initial reservoir level (0.25 m), respectively, for cases with 33%, 50%, and 66% contraction ratios to the channel width (0.3 m). For the same cases at a certain time of t = 5.0 s, the reflected wave reached 1.1 m downstream, 0.5 m downstream, and 0.1 m upstream of the initial dam location. Waves generated by the trapezoidal configuration affected the upstream in less time than those formed by the crescent contraction. The length of the transitions or their placement (middle of/across the channel) did not significantly affect the flow profile upstream; however, within the converging zone, longer configurations resulted in a wider increased water elevation. Overall, the intensity of the hydraulic response can be related to one factor in all cases, namely, the convergence intensity of the flow lines as they entered the contractions. Full article

Background/Objectives: Medium- and long-chain triacylglycerol (MLCT) and 2′-fucosyllactose (2′-FL) are functional ingredients abundant in human milk; however, their effects on small intestinal development and health remain largely unknown, and no research has explored their potential combined effects. Methods: In this study, growing C57BL/6 mice (3 weeks old) were fed diets without or with 2.5 g/100 g of MLCT, 2′-FL, or the combination (MLCT + 2′-FL; 5:1) for 21 days. Body weight, major organ indices, small intestinal morphology-related indicators (small intestinal length, villus height, crypt depth, villus height/crypt depth (V/C) ratio, and epithelial cell proliferation), and intestinal barrier function markers (goblet cell and Paneth cell count, protein expression of ZO-1 and occludin, and levels of sIgA and LPS) were measured. Results: In addition to the shared promotion of epithelial cell proliferation, MLCT intervention raised villus height and crypt depth, while 2′-FL intervention elevated Paneth cell count and sIgA levels. Notably, MLCT + 2′-FL intervention offered additional advantages (increasing the V/C ratio, goblet cell count, and expression of ZO-1 and occludin) without affecting crypt depth. 16S rRNA sequencing analysis of cecal contents revealed that all three interventions mainly affected beta diversity rather than alpha diversity, and enriched differentially abundant bacterial taxa: Erysipelotrichaceae, Faecalibaculum, UBA1819, and Faecalitalea in the MLCT group; Enterobacteriaceae, Escherichia, and Allobaculum in the 2′-FL group; Bifidobacterium, Romboutsia, Clostridia, and several other bacterial taxa in the MLCT + 2′-FL group. Conclusions: These results indicate that MLCT and 2′-FL interventions alone appear to provide different benefits for small intestinal development, and their combination may confer more comprehensive advantages. Full article

Skywells are crucial for climate regulation in traditional Chinese dwelling architecture, exhibiting significant variations across climatic regions. This study focuses on humid–hot China, using Huangshan, to explore skywell parameters’ impact on thermal comfort and energy efficiency. Field research on 24 buildings in the World Heritage Site Xidi, Hong Villages, and Chinese Historical Pingshan Village, combined with Grasshopper’s Ladybug tool, established a parametric model. Using orthogonal design, performance simulation, and Python-based machine learning, six morphological parameters were analyzed: width-to-length ratio, height-to-width ratio, orientation, hall depth, wing width, and shading width. After NSGA-II multi-objective optimization, the summer Percentage of Time Comfortable (P_TC) increased by 5.3%, 38.14 h; the Universal Thermal Climate Index (UTCI) relatively improved by 2%; energy consumption decreased by 8.6%, 0.14 kWh/m²; and the useful daylight illuminance increased by 28%, 128.4 h. This confirms the climate adaptability of courtyard-style buildings in humid–hot China and identifies optimized skywell parameters within the study scope. Full article

Suction caisson anchor foundations have been widely applied in oil and gas platforms but remain in the exploratory stage for floating offshore wind power applications, where research on their anchor load-bearing characteristics is insufficient. This study focuses on the influence of length-to-diameter ratio, loading angle, and loading point depth on the anchor load-bearing characteristics of suction caisson anchor foundations. Through numerical simulation, the load–displacement curves, internal force distribution along the caisson body, movement mode transitions, and soil failure characteristics were obtained. The results indicate that loading point depth and loading angle alter the movement mode of the suction caisson anchor foundation, directly affecting its bearing capacity. Smaller loading angles result in higher bearing capacity, which initially increases with loading point depth, peaks at 0.6 L, and then decreases at 0.8 L due to a transition in the foundation’s movement mode. Similarly, as the length-to-diameter ratio decreases, the bearing capacity and overall movement amplitude of the foundation decrease, leading to a shift in the optimal loading point position. The circumferential soil pressure and horizontal soil resistance distributions vary significantly with loading angle and depth. The findings of this study provide valuable reference for the design and application of suction caisson anchor foundations. Full article

This study conducts numerical analysis of fatigue crack propagation in deck-rib welded joints of orthotropic steel decks (OSDs) using linear elastic fracture mechanics. The stress intensity factor for central surface cracks under constant range bending stress is calculated, and single and multi-crack propagation are simulated by a numerical integration method. The research results show that deck geometry critically influences crack propagation behavior. Wider decks accelerate propagation of cracks after the crack depth exceeds half the deck thickness, thicker decks exhibit linearly faster propagation rates yet retain larger residual section to bear loads, and increased weld penetration reduces fatigue life. Initial defects rapidly converge to a preferred propagation path, stabilizing near $a_f/c_f\approx 0.1$ ($a_f$ is the failure crack depth and $c_f$ is the half surface crack length) regardless of initial aspect ratio. For multi-crack scenarios, defect density dominates merging, doubling density increases final cracks by 45%. Merged cracks adhere closely to the single-crack path, while total section loss escalates with defect density and deck thickness but remains stress range independent. The identified convergence preferred propagation path enables depth estimation from surface-length measurements during real bridge inspections. Full article

The effects of varying dietary metabolizable energy (ME) and crude protein (CP) levels, along with their interactive effects, on the apparent nutrient metabolism, development of digestive organs, intestinal morphology, and microbiota composition in Jingyuan chickens during the growing phase were evaluated. A total of 540 seven-week-old male Jingyuan chickens were randomly assigned to nine groups, with six replicates per group and 10 chickens per replicate. The trial lasted for 11 weeks. A 3 × 3 factorial design was adopted, comprising three levels of ME, namely, low (11.28 MJ/kg, LE group), medium (11.70 MJ/kg, ME group), and high (12.12 MJ/kg, HE group) and three levels of CP, namely, low (14.00%, LP group), medium (15.50%, MP group), and high (17.00%, HP group). The levels of ME and CP, along with their interactions, had significant effects on the average daily gain (ADG), average daily feed intake, feed conversion ratio (FCR), apparent metabolizable rate of CP, gizzard weight, duodenal lengths, jejunal villus height (VH), crypt depth (CD), and muscle layer thickness (MLT) (p < 0.05). The combination of medium level ME (11.70 MJ/kg) and medium level CP (15.50%) (MEMP group) exhibited the best performance, with the highest ADG and the lowest FCR (p < 0.05). Moreover, this group showed significantly higher duodenal length, jejunal CD, VH/CD and MLT compared with the other groups (p < 0.05). Dietary ME and CP levels greatly influenced cecal microbiota composition. Chickens in the MEMP group exhibited an increased abundance of Erysipelotrichaceae, Syntrophomonadaceae, Akkermansia, and Clostridia_vadinBB60_group, and there was an obvious decrease in the relative abundance of Desulfobacterota (p < 0.05). This study demonstrated that dietary ME and CP levels, along with their interactions, could significantly influence the growth performance, apparent nutrient metabolism, and intestinal development of Jingyuan chickens during the growing phase. Dietary ME and CP levels modulated the cecal microbiota composition, potentially inhibiting the abundance of harmful bacteria Desulfobacterota, while enriching the abundance of beneficial bacteria, thereby enhancing gut development and nutrient absorption. The combination of medium-level ME and CP (11.70 MJ/kg ME, 15.50% CP) demonstrated the most favorable outcomes in our study. Full article

Lock-in thermography is a widely adopted infrared nondestructive testing technique that detects subsurface defects by applying modulated thermal waves and analyzing the resulting surface temperature variations. However, quantitatively characterizing subsurface defects at varying depths remains a significant challenge. This study explores the lateral resolution of subsurface defect detection using phase-based lock-in thermography, integrating analytical modeling, finite element simulation, and phase difference analysis. The results demonstrate that defect visibility and boundary definition are highly influenced by the excitation frequency. The thermal diffusion length, which is inversely proportional to the square root of the excitation frequency, governs both the penetration depth and the lateral spread of thermal energy. Higher frequencies enhance lateral resolution, whereas lower frequencies improve the detectability of deeper defects. Detection becomes particularly difficult for defects with small radii or low radius-to-depth ratios. A critical radius-to-depth threshold of 2 is identified as essential for reliable boundary delineation. These findings offer practical guidance for selecting excitation frequencies to achieve an optimal balance between depth sensitivity and lateral resolution in thermal-wave-based nondestructive evaluation. Full article

Fecal microbiota transplantation (FMT) promotes growth performance and intestinal development in yellow-feathered broilers, but whether the virome and metabolites contribute to its growth-promoting effect remains unclear. This study removed the microbiota from FMT filtrate using a 0.45 μm filter membrane, retaining the virome and metabolites to perform fecal virome transplantation (FVT), aiming to investigate its regulatory role in broiler growth. Healthy yellow-feathered broilers with high body weights (top 10% of the population) were used as FVT donors. Ninety-six 8-day-old healthy male yellow-feathered broilers (95.67 ± 3.31 g) served as FVT recipients. Recipient chickens were randomly assigned to a control group and an FVT group. The control group was gavaged with 0.5 mL of normal saline daily, while the FVT group was gavaged with 0.5 mL of FVT solution daily. Growth performance, immune and antioxidant capacity, intestinal development and related gene expression, and microbial diversity were measured. The results showed that FVT improved the feed utilization rate of broilers (the feed conversion ratio decreased by 3%; p < 0.05), significantly increased jejunal length (21%), villus height (69%), and crypt depth (84%) (p < 0.05), and regulated the jejunal barrier: insulin-like growth factor-1 (IGF-1) (2.5 times) and Mucin 2 (MUC2) (63 times) were significantly upregulated (p < 0.05). FVT increased the abundance of beneficial bacteria Lactobacillales. However, negative effects were also observed: Immunoglobulin A (IgA), Immunoglobulin G (IgG), Immunoglobulin M (IgM), Interleukin-1 beta (IL-1β), Interleukin-6 (IL-6), Tumor Necrosis Factor-alpha (TNF-α), and Interferon-gamma (IFN-γ) in broilers were significantly upregulated (p < 0.05), indicating immune system overactivation. Duodenal barrier-related genes Mucin 2 (MUC2), Occludin (OCLN), Claudin (CLDN1), and metabolism-related genes solute carrier family 5 member 1 (SLC5A1) and solute carrier family 7 member 9 (SLC7A9) were significantly downregulated (p < 0.05). The results of this trial demonstrate that, besides the microbiota, the gut virome and metabolites are also functional components contributing to the growth-promoting effect of FMT. The differential responses in the duodenum and jejunum reveal spatial heterogeneity and dual effects of FVT on the intestine. The negative effects limit the application of FMT/FVT. Identifying the primary functional components of FMT/FVT to develop safe and targeted microbial preparations is one potential solution. Full article

The corrosion of high-strength steel wires is a key factor impacting the durability and reliability of cable-stayed bridges. In this study, the corrosion pit features on a high-strength steel wire, which had been in service for 27 years, were extracted and modeled using three-dimensional point cloud data obtained through 3D surface scanning. The Otsu method was applied for image binarization, and each corrosion pit was geometrically represented as an ellipse. Key pit parameters—including length, width, depth, aspect ratio, and a defect parameter—were statistically analyzed. Results of the Kolmogorov–Smirnov (K–S) test at a 95% confidence level indicated that the directional angle component (θ) did not conform to any known probability distribution. In contrast, the pit width (b) and defect parameter (Φ) followed a generalized extreme value distribution, the aspect ratio (b/a) matched a Beta distribution, and both the pit length (a) and depth (d) were best described by a Gaussian mixture model. The obtained results provide valuable reference for assessing the stress state, in-service performance, and predicted remaining service life of operational stay cables. Full article

We investigate the temperature evolution in the three-dimensional skin tissue exposed to a millimeter-wave electromagnetic beam that is not necessarily perpendicular to the skin surface. This study examines the effect of the beam’s incident angle. The incident angle influences the thermal heating in two aspects: (i) the beam spot projected onto the skin is elongated compared to the intrinsic beam spot in a perpendicular cross-section, resulting in a lower power per skin area; and (ii) inside the tissue, the beam propagates at the refracted angle relative to the depth direction. At millimeter-wavelength frequencies, the characteristic penetration depth is sub-millimeter, whereas the lateral extent of the beam spans at least several centimeters in applications. We explore the small ratio of the penetration depth to the lateral length scale in a nondimensional formulation and derive a leading-term asymptotic solution for the temperature distribution. This analysis does not rely on a small incident angle and is therefore applicable to arbitrary angles of incidence. Based on the asymptotic solution, we establish scaling laws for the three-dimensional skin temperature, the skin surface temperature, and the skin volume in which thermal nociceptors are activated. Full article

Articulated Tugs and Barges (ATBs) are increasingly recognised for their effectiveness in transporting chemicals, petroleum, bulk goods, and containers, primarily due to their exceptional flexibility and fuel efficiency. Recent projections indicate that the ATB market is on track for significant growth, which is expected to lead to an increase in the annual growth rate from 2025 to 2032. This study aims to analyse the current advancements in ATB technology and provide insights into the ATB fleet and the systems that connect tugboats and barges. Furthermore, it highlights the advantages of this transportation system, especially regarding its role in enhancing energy efficiency within the maritime transport sector. Currently, there is limited information available in the public domain about ATBs compared to other commercial vessels. The analysis reveals that much of the required information for modern ATB design is not accessible outside specialised design companies. The study also focuses on conceptual design aspects, which include the main dimensions, articulated connections, propulsion systems, and machinery, concluding with an evaluation of economic viability. Special emphasis is placed on defining the main dimensions, which is a critical part of the complex design process. In this context, the ratios of length to beam (L/B), beam to draft (B/D), beam to depth (B/T), draft to depth (T/D), and power to the number of tugs cubed (Pw/N³) are established as design control parameters in the conceptual design phase. This aspect underscores the novelty of the present study. Additionally, the economic viability is analysed in terms of both CAPEX (capital expenditures) and OPEX (operational expenditures). While CAPEX does not significantly differ between the methods used in different types of commercial ships, OPEX should account for the unique characteristics of ATB vessels. Full article