Search Results (34)

Calcium leaching is a key degradation mechanism governing the long-term durability of cement-based materials, particularly in marine environments where multi-ionic interactions significantly alter dissolution behavior. In this study, the solid–liquid equilibrium of calcium in hardened Portland cement exposed to NaCl solution and artificial seawater was experimentally established. A wide range of equilibrium states was achieved by varying the liquid-to-solid ratio, and the corresponding aqueous chemistry and phase assemblage were characterized using ICP-AES, XRD, and SEM-EDS. The results show that both NaCl solution and seawater substantially increase the equilibrium calcium concentration compared to deionized water, with a much stronger effect observed in seawater. In NaCl solution, the equilibrium relationship follows a classical three-stage decalcification process. In contrast, seawater induces coupled dissolution–precipitation reactions due to the presence of Mg²⁺ and SO₄²⁻, leading to rapid and extensive decalcification within a narrow calcium concentration range. The findings provide important experimental evidence for improving thermodynamic models and predicting the long-term degradation of Portland cement concrete in marine environments. Full article

Water-based lubricants (WBLs) are increasingly being considered for electrified drivetrain applications; however, their electrochemical stability toward bearing steels remains insufficiently understood. This study evaluated the corrosion behavior of through-hardened AISI 52100 bearing steel in novel WBLs to elucidate the corrosion kinetics and surface degradation mechanisms. Round steel disks were cleaned and tested in 50 wt% aqueous dilutions of glycerol, ethylene glycol (MEG), polyethylene glycol (PEG), and polyalkylene glycol (PAG). Electrochemical measurements were conducted using a three-electrode cell in accordance with ASTM G3-14, employing open circuit potential (OCP), linear polarization resistance (LPR), electrochemical impedance spectroscopy (EIS), and potentiodynamic polarization curves. Among the uninhibited fluids, DI water exhibited the highest corrosion current density (19.85 µA/cm²), while glycerol- and PEG-based systems showed the lowest values (0.79 and 0.85 µA/cm², respectively), attributed to organic adsorption at the steel/electrolyte interface. EIS analysis revealed a single charge-transfer-controlled process across all fluids, consistent with a weak, non-passive interfacial oxide whose protective character is modulated by organic adsorption. The addition of NaNO₃ produced divergent effects depending on the base fluid chemistry: the corrosion activity was reduced in DI water and glycerol systems through enhanced passivation, while PEG- and PAG-based formulations showed increased corrosion current densities and reduced charge transfer resistance, attributed to competitive disruption of the polymer boundary layer by nitrate ions. Surface characterization by SEM/EDAX and white-light interferometry corroborated the electrochemical findings, revealing fluid-dependent corrosion morphologies ranging from uniform attack in DI water to localized pitting in polymer-based systems, with NaNO₃ shifting the corrosion mode in PEG/PAG systems from localized to combined localized and uniform attack. These findings highlight the critical role of fluid chemistry in controlling corrosion processes in water-based lubricants and provide mechanistic insight for the development of corrosion-stable formulations for high-performance electrified drivetrain applications. Full article

Geopolymer concrete (GPC) has emerged as a promising low-carbon alternative to ordinary Portland cement (OPC), yet wider adoption is limited by the lack of standardised mix-design procedures. Precursor, activator, curing, and aggregates strongly interact to affect properties, but findings are scattered and hard to generalise. This review consolidates and normalises published findings to clarify how key parameters-precursor type, activator dosage and concentration, activator-to-binder ratio, curing temperature, and aggregate gradation-control fresh and hardened performance. Overall trends indicate that calcium-rich systems enhance early strength by 80–100% at typical replacement levels; while optimum activator conditions of 12 M NaOH and sodium silicate/sodium hydroxide ratio = 2.5 commonly improve strength by 40–60% relative to sub-optimal ratios; alkaline activator-to-binder ratios of 0.4–0.7 provide the most practical strength-workability balance. Heat curing at 80–100 °C significantly accelerates early-age property development by 50–200% compared to ambient curing, depending on duration and activator chemistry. A target-strength mix design is demonstrated through a 40 MPa case study. Using a compiled dataset for fly ash (FA)-based GPC, a modulus–strength framework is proposed; common OPC code equations over-predict elastic modulus for 15–50 MPa, and calibration yields a conservative, code-compatible relation: E = $2.75\sqrt{f{c}_{MPa}}$. Key limitations are highlighted, including variability in raw materials and durability uncertainties, and future directions are proposed toward performance-based design and standardisation to support structural use of GPC in sustainable infrastructure. Full article

This study systematically examines the fluidity, setting time, mechanical properties, and microstructural evolution of metakaolin-based geopolymer grouting materials with a relatively high water-to-solid (W/S) ratio window. A four-factor, three-level orthogonal experimental design was employed to identify the dominant factors and main effect trends of W/S ratio, alkali dosage, water glass modulus (Ms, molar ratio of SiO₂ to Na₂O in alkali solution), and steel slag content on the material’s performance. The results indicated that the W/S ratio predominantly governed fluidity, while the alkali content was the primary controlling factor for setting time and early-age strength. An intermediate range of water glass modulus with a value of 1.6 provided balanced performance. The incorporation of steel slag with a range of 10–20% showed an age-dependent contribution: it not only tended to improve the rheology of the paste but also the later-age strength. XRD, FTIR, and SEM/EDS results suggested that the hardened binders were dominated by amorphous products, where alumimosilicate gel (N-A-S-H) and Ca-containing gel (C-S-H/C-A-S-H) may coexist depending on calcium availability and activator chemistry. The proposed parameter ranges are valid within the studied design space and provide guidance for the mix design of high-W/S geopolymer grout. Full article

Aluminum alloys require improved surface performance to satisfy the demands of today’s aerospace, automotive, marine, and structural applications. This paper compares three key surface hardening methods: diffusion-assisted microalloying, thermomechanical deformation-based treatments, and composite/hybrid reinforcing procedures. Diffusion-assisted Zn/Mg enrichment allows for localized precipitation hardening but is limited by the native Al₂O₃ barrier, slow solute mobility, alloy-dependent solubility, and shallow hardened depths. In contrast, thermomechanical techniques such as shot peening, surface mechanical attrition treatment (SMAT), and laser shock peening produce ultrafine/nanocrystalline layers, high dislocation densities, and deep compressive residual stresses, allowing for predictable increases in hardness, fatigue resistance, and corrosion performance. Composite and hybrid reinforcement systems, such as SiC, B₄C, graphene, and graphite-based aluminum matrix composites (AMCs), use load transfer, Orowan looping, interfacial strengthening, and solid lubrication effects to enhance wear resistance and through-thickness strengthening. Comparative evaluations show that, while diffusion-assisted procedures are still labor-intensive and solute-sensitive, thermomechanical treatments are more industrially established and scalable. Composite and hybrid systems provide the best tribological and load-bearing performance but necessitate more sophisticated processing approaches. Recent corrosion studies show that interfacial chemistry, precipitate distribution, and galvanic coupling all have a significant impact on pitting and stress corrosion cracking (SCC). These findings highlight the importance of treating corrosion as a fundamental design variable in all surface hardening techniques. This work uses unified tables and drawings to provide a thorough examination of strengthening mechanisms, corrosion and fatigue behavior, hardening depth, alloy suitability, and industrial feasibility. Future research focuses on overcoming diffusion barriers, establishing next-generation gradient topologies and hybrid processing approaches, improving strength ductility corrosion trade-offs, and utilizing machine-learning-guided alloy design. This research presents the first comprehensive framework for selecting multifunctional aluminum surfaces in demanding aerospace, automotive, and marine applications by seeing composite reinforcements as supplements rather than strict alternatives to diffusion-assisted and thermomechanical approaches. Full article

This study follows the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) framework, combining bibliometric mapping and mechanistic synthesis to provide a unified evidence-based review of cementitious grouts in ground support systems. The bibliometric layer quantifies global research activity, while the systematic synthesis interprets how material composition, pozzolanic chemistry, and rheology control grout performance and sustainability. This study presents a systematic review complemented by bibliometric analysis to synthesise global research trends and technical advances in grout design. A dataset of 1200 articles was screened, from which 101 journal papers met the inclusion and quality criteria and were analysed in detail. Co-occurrence mapping of author keywords was then used to identify research hotspots and collaborative structures. The bibliometric analysis revealed that Construction and Building Materials is the leading outlet. Co-authorship mapping highlighted strong international collaboration, with leading clusters centred on supplementary cementitious materials, rheology, and microstructural analysis. The technical review consolidates five interrelated themes: reinforcement mechanisms, cementitious grouts, chemical reactions and pozzolanic reactivity, fresh and hardened state properties, and microstructural development with rheological behaviour. Across these themes, supplementary cementitious materials and waste-derived binders have emerged as central to both performance enhancement and carbon reduction, while advanced experimental and modelling techniques have refined understanding of microstructural evolution and grout–rock–bolt interactions. Collectively, the findings underline that cementitious grouts are no longer passive fillers but engineered composites designed for mechanical efficiency, durability, and environmental responsibility. Key research gaps remain in the standardisation of rheological testing, long-term durability under complex field conditions, and integration of life-cycle assessment into grout development. Addressing these challenges will be critical for the design of next-generation grouts capable of meeting the dual imperatives of safety and sustainability in mining and civil engineering. Full article

This paper deals with an important issue, which is the influence of failure caused by the quality of matrix post-curing on the strength of complex and difficult materials of the “new generation” such as fibre composites, particularly with a polymer matrix. In recent years, significant advances in the field of adhesive materials chemistry have led to the constant development of bonding technology. The effectiveness of bonding depends, to a large extent, on the suitable selection of the adhesive and the use of appropriate surface treatment technology. It is difficult to imagine virtually any modern industry without adhesive joints, be it the aircraft, aerospace or automotive industries, which simultaneously highlights the great importance of adhesives and adhesive materials for the present-day economy. In modern technology, it is extremely important to obtain the right combination of modern construction materials. The statistical analysis of the components showed the complexity of the layered composite structure. The proposed model of the weakest micro-volume developed in this study indirectly reflects the experimentally based curing variables that affect the stresses of the components in the composite (laminate) structure. The strength of fibrous composite structures based on the Markov chain theory considers technological aspects during hardening. The model proposed in the paper was validated on the basis of examples from the literature and experimental data obtained in the research project. The numerical results are in good agreement with the literature database and measurement data. The presented model could be a novel method, which allows better insight into the curing process of epoxy resins. Full article

The surface chemistry of epoxy resin and its composites is critical for their long-term performance across various applications. In this study, we investigate the main reactions occurring on the surface of DEGBA/DEGBF epoxy resin following curing, post-curing, and thermal post-curing processes using Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS). ToF-SIMS analysis elucidated molecular details, including curing and cross-linking progression, cross-link characteristics, cured resin structure, residual unreacted hardener, cross-linking density, and reaction pathways. Principal Components Regression analysis (PCR) was applied to distinguish between cured and post-cured samples, focusing on specific ions indicative of the curing process. The completion of curing was associated with ions such as C₁₄H₇O⁺, CHO⁺, CH₃O⁺, and C₂₁H₂₄O₄⁺, while unreacted hardener was indicated by C₂₁H₂₄O₄⁺ ions. Cross-linking density and the intensities of aliphatic hydrocarbons were crucial in differentiating curing stages. Calibration ensured that all ion intensities totaled to one, and specific ions were tracked to monitor the states from uncured to post-cured. Negative spectra provided insights into the consumption of hardener molecules during curing and post-curing. The results demonstrated that post-curing enhances the properties of epoxy resin by promoting further cross-linking, reducing residual unreacted groups, and forming a more extensive covalent network. This results in improved mechanical and thermal stability. The molecular changes observed through ToF-SIMS data effectively distinguish between curing and post-curing reactions, contributing to a better understanding and optimization of epoxy resin properties for various applications. Full article

Environmental issues and the reduction of fossil fuel resources will lead to the partial or total substitution of petroleum-based materials with natural, raw, renewable ones. One expanding domain is the obtaining of engineering materials from vegetable oils for sustainable, eco-friendly polymers for different applications. Herein, the authors propose a simplified and green synthesis pathway for a thermally curable, acrylated and epoxidized soybean oil matrix formulation containing only epoxidized soybean oil, acrylic acid, a reactive diluent (5%) and just 0.15 mL of catalyst. The small amount of reactive diluent significantly reduced the initial system viscosity while eliminating the need for adding solvent, hardener, activator, etc. Both the thermally cured composite with a 2% TiO₂ microparticle filler and its pristine matrix were comparably characterized in terms of structural, thermal, morphological, dielectric and wettability by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetry, scanning electron microscopy, broadband dielectric spectrometry and contact angle measurements. The 2% filler in the composite generated superior thermal stability via lower mass loss (48.89% vs. 57.14%) and higher degradation temperatures (395 °C vs. 387 °C), increased the glass transition temperature from −20 °C to −10 °C, rendered the microcomposite hydrophobic by increasing the contact angle from 88° to 96° and enhanced dielectric properties compared to the pristine matrix. All investigations recommend the microcomposite for protective coatings, capacitors, sensors and electronic circuits. This study brings new contributions to green chemistry and sustainable materials. Full article

Sustainability and the quest for a more robust construction material cannot be divorced from each other. While Portland cement has revolutionized the construction sector, its environmental toll, particularly in greenhouse gas emissions and global warming, cannot be ignored. Addressing this dilemma requires embracing alternatives like geopolymer cement/geopolymer binder (GPC/GPB). Over the last few decades, considerable strides have been achieved in advancing GPC as a sustainable construction material, including its utilization in pavement construction. Despite these advances, gaps still exist in GPC optimal potential in pavement construction, as most studies have concentrated on specific attributes rather than on a comprehensive evaluation. To bridge this gap, this review adopts a novel, holistic approach by integrating environmental impacts with performance metrics. To set the stage, this review first delves into the geopolymer concept from a chemistry perspective, providing an essential broad overview for exploring GPC’s innovations and implications in pavement applications. The findings reveal that GPC not only significantly reduces greenhouse gas emissions and energy consumption compared to Portland cement but also enhances pavement performance. Further, GPC concrete pavement exhibits superior mechanical, durability, and thermal properties to ensure its long-term performance in pavement applications. However, challenges to GPC utilization as a pavement material include the variability of raw materials, the need for suitable hardeners, the lack of standardized codes and procedures, cost competitiveness, and limited field data. Despite these challenges, the process of geopolymerization presents GPC as a sustainable material for pavement construction, aligning with Sustainable Development Goals (SDGs) 3, 9, 11, and 12. Full article

The liquid crystal state (LC) in polymer chemistry is a topic discussed in varied materials research. The anisotropic properties typical of these compounds are mostly the result of the presence of mesogens in the structure of liquid crystals. This article traces the development of liquid crystal science, focusing on liquid crystal epoxy resins (LCERs) and emphasizing the crucial role of mesogens and their diverse effect on the materials. It also highlights the importance of understanding the morphology of LC polymers, explaining their profound impact on material properties and performance. It explores the cross-linking process of liquid crystal resins and composites, describing how changes in structural factors affect material structure. The article also provides information about hardeners and their influence on the cross-linked structure. Various nanofillers were also discussed, elucidating their impact on the resulting composites. Full article

The Structural Health Monitoring (SHM) capabilities of a well-studied self-healing epoxy resin based on disulfide bonds, through the addition of carbon nanotubes (CNTs), are studied. Since these materials demonstrated, in recent works, a high dependency of the dynamic hardener content on the repair performance, this study aimed to analyze the effect of the vitrimeric chemistry on the electromechanical properties by studying different 2-aminophenyl disulfide (2-AFD) hardener and CNT contents. The electrical conductivity increases with both the CNT and AFD contents, in general. Moreover, an excess of AFD close to the stoichiometric ratio with a low CNT content improved the tensile strength by 45%, while higher AFD contents promoted its detriment by 41% due to a reduced crosslinking density. However, no significant difference in the mechanical properties was observed at a higher CNT content, regardless of the AFD ratio. The developed materials demonstrate a robust electromechanical response at quasi-static conditions. The sensitivity significantly increases at higher AFD ratios, from 0.69 to 2.22 for the 0.2 wt.%. CNT system, which is advantageous due to the enhanced repair performance of these vitrimeric materials with a higher hardener content. These results reveal the potential use of self-healing vitrimers as integrated SHM systems capable of detecting damages and self-repairing autonomously. Full article

In the current work, we design a novel medium Mn steel with a superior mechanical property and no Lüders band. For industrial applications, a “low Mn addition” chemical composition and two kinds of different annealing processes with various initial microstructures were introduced. Consequently, the sample subjected to full austenitized quenching plus intercritical annealing process exhibited an outstanding mechanical property without the Lüders band. The microstructural evolution and austenite reverted transformation behavior were discussed in detail. In addition, austenite stability was estimated by chemistry stability and mechanical stabilization. It seemed that the austenite stability was significantly influenced by the morphological component. Thus, the sample with single lath-like ferrite and austenite exhibited the most excellent mechanical property. Furthermore, the “Lüders band” phenomenon was considered to rely on the restriction of martensitic recovery and recrystallization by lath-like morphology. The occurrence of the Lüders band was attributed to the low work-hardening ability caused by dynamic recovery. The formation of lath-like morphology could prevent the occurrence and propagation of the Lüders band by increasing the dislocation density and active TRIP effect. Full article

This study aims to develop a material-saving performance prediction model for fast-hardening alkali-activated slag/silica fume blended pastes. The hydration process in the early stage and the microstructural properties after 24 h were analyzed using design of experiments (DoE). The experimental results show that the curing time and the FTIR wavenumber of the Si-O-T (T = Al, Si) bond in the band range of 900–1000 cm⁻¹ after 24 h can be predicted accurately. In detailed investigations, low wavenumbers from FTIR analysis were found to correlate with reduced shrinkage. The activator exerts a quadratic and not a silica modulus-related conditioned linear influence on the performance properties. Consequently, the prediction model based on FTIR measurements proved to be suitable in evaluation tests for predicting the material properties of those binders in the building chemistry sector. Full article

Even if cement is a well-consolidated material, the chemistry of cement (and the chemistry inside cement) remains very complex and still non-obvious. What is sure is that the hydration mechanism plays a pivotal role in the development of cements with specific final chemical compositions, mechanical properties, and porosities. This document provides a survey of the chemistry behind such inorganic material. The text has been organized into five parts describing: (i) the manufacture process of Portland cement, (ii) the chemical composition and hydration reactions involving a Portland cement, (iii) the mechanisms of setting, (iv) the classification of the different types of porosities available in a cement, with particular attention given to the role of water in driving the formation of pores, and (v) the recent findings on the use of recycled waste materials in cementitious matrices, with a particular focus on the sustainable development of cementitious formulations. From this study, the influence of water on the main relevant chemical transformations occurring in cement clearly emerged, with the formation of specific intermediates/products that might affect the final chemical composition of cements. Within the text, a clear distinction between setting and hardening has been provided. The physical/structural role of water in influencing the porosities in cements has been analyzed, making a correlation between types of bound water and porosities. Lastly, some considerations on the recent trends in the sustainable reuse of waste materials to form “green” cementitious composites has been discussed and future considerations proposed. Full article