Search Results (302)

This study investigates the improvement effect and micro-mechanism of guar gum and palm fibers, two eco-friendly materials, on expansive soil. The study uses disintegration tests, unconfined compressive strength tests, triaxial compression tests, and SEM analysis to evaluate the enhancement of mechanical properties. The results show that the guar gum–palm fiber composite significantly improves the compressive and shear strength of expansive soil. The optimal ratio is 2% guar gum, 0.4% palm fiber, and 6 mm palm fiber length. Increasing fiber length initially boosts and then reduces unconfined compressive strength. Guar gum increases unconfined compressive strength by 187.18%, further improved by 20.9% with palm fibers. When fiber length is fixed, increasing palm fiber content increases and then stabilizes peak stress and shear strength (cohesion and internal friction angle), improving by 27.30%, 52.1%, and 12.4%, respectively, compared to soil improved with only guar gum. Micro-analysis reveals that guar gum enhances bonding between soil particles via a gel matrix, improving water stability and mechanical properties, while palm fibers reinforce the soil and inhibit crack propagation. The synergistic effect significantly enhances composite-improved soil performance, offering economic and environmental benefits, and provides insights for expansive soil engineering management. Full article

Sustainability in the construction sector has become a fundamental objective for mitigating escalating environmental challenges; given that concrete is the most widely used man-made material, extending its service life is therefore critical. Among durability concerns, magnesium sulfate (MgSO₄) attack is particularly deleterious to concrete structures. Therefore, this study investigates the short- and long-term performance of concrete produced with copper slag (CS)—a massive waste generated by copper mining activities worldwide—employed as a supplementary cementitious material (SCM), together with recycled coarse aggregate (RCA), obtained from concrete construction and demolition waste, when exposed to MgSO₄. CS was used as a 15 vol% cement replacement, while RCA was incorporated at 0%, 20%, 50%, and 100 vol%. Compressive strength, bulk density, water absorption, and porosity were measured after water curing (7–388 days) and following immersion in a 5 wt.% MgSO₄ solution for 180 and 360 days. Microstructural characteristics were assessed using scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric analysis with its differential thermogravimetric derivative (TG-DTG), and Fourier transform infrared spectroscopy (FTIR) techniques. The results indicated that replacing 15% cement with CS reduced 7-day strength by ≤10%, yet parity with the reference mix was reached at 90 days. Strength losses increased monotonically with RCA content. Under MgSO₄ exposure, all mixtures experienced an initial compressive strength gain during the short-term exposures (28–100 days), attributed to the pore-filling effect of expansive sulfate phases. However, at long-term exposure (180–360 days), a clear strength decline was observed, mainly due to internal cracking, brucite formation, and the transformation of C–S–H into non-cementitious M–S–H gel. Based on these findings, the combined use of CS and RCA at low replacement levels shows potential for producing environmentally friendly concrete with mechanical and durability performance comparable to those of concrete made entirely with virgin materials. Full article

Co_0.95R_0.05Fe₂O₄ nanoparticles with R = La, Pr, Nd, Sm, and Eu were synthesized via an environmentally friendly sol–gel method. The prepared samples were studied using X-ray diffraction measurements (XRD), transmission electron microscopy (TEM), X-ray photoelectron microscopy (XPS), and magnetic measurements. All compounds were found to be single phases adopting a cubic Fd-3m structure. EDS analysis confirmed the presence of Co, Fe, R, and oxygen in all cases. The XPS measurements reveal that the Co 2p core-level spectra are characteristic for Co³⁺ ions, as indicated by the 2p_3/2 and 2p_1/2 binding energies and spin–orbit splitting values. The analysis of the Fe 2p core-level spectra reveals the presence of both Fe³⁺ and Fe²⁺ ions in the investigated samples. The doped samples exhibit lower saturation magnetizations than the pristine sample. Very good agreement with the saturation magnetization values was obtained if we assumed that the light rare-earth ions occupy octahedral sites and their magnetic moments align parallel to those of the 3d transition metal ions. The ZFC-FC curves indicate that some nanoparticles remain superparamagnetic, while others exhibit ferrimagnetic ordering at room temperature, suggesting the presence of interparticle interactions. The M_r/M_s ratio at room temperature reflects the dominance of magnetostatic interactions. Full article

Some additives currently used to enhance drilling mud’s rheological qualities have a substantial economic impact on society. Carboxymethyl cellulose (CMC) and calcium carbonate (CaCO₃) are currently imported. Food crops have influences on food security; hence, this research explored the potential of utilizing cow bone powder (CBP), a bio-waste product and a renewable resource, as an environmentally friendly fluid-loss additive for drilling applications, in comparison with CaCO₃. Both samples (CBP and CaCO₃) were evaluated to determine the most efficient powder sizes (coarse, medium, and fine powder), concentrations (5–15 g), and aging conditions (before or after aging) that would offer improved rheological and fluid-loss control. The results obtained showed that CBP had a significant impact on mud rheology when compared to CaCO₃. Decreasing the particle size (coarse to fine particles) and increasing the concentration from 5 to 15 g positively impacted mud rheology. Among all the conditions analyzed, fine-particle CBP with a 15 g concentration produced the best characteristics, including in the apparent viscosity (37 cP), plastic viscosity (29 cP), and yield point (25.5 lb/100 ft²), and a gel strength of 16 lb/100 ft² (10 s) and 28 lb/100 ft² (10 min). The filtration control ability of CaCO₃ was observed to be better than that of the coarse and medium CBP particle sizes; however, fine-particle-size CBP demonstrated a 6.1% and 34.6% fluid-loss reduction at 10 g and 15 g concentrations when compared to respective amounts of CaCO₃. The thermal behavior of the Mud Samples demonstrated that it positively impacted rheology before aging. In contrast, after aging, it exhibited a negative effect where samples grew more viscous and exceeded the API standard range for mud properties. Therefore, CBP’s excellent rheological and fluid-loss control ability makes it a potential, sustainable, and economically viable alternative to conventional materials. This superior performance enhances the thinning properties of drilling muds in stationary and circulating conditions. Full article

The dependence of conventional epoxy resins on fossil fuels and the environmental and health hazards associated with bisphenol A (BPA) demand the creation of sustainable alternatives. Because lignin is a natural resource and has an aromatic ring skeleton structure, it could be used as an alternative to fossil fuels. This study effectively resolved this challenge by utilizing a sustainable one-step epoxidation process to transform lignin into a bio-based epoxy resin. The results verified the successful synthesis of epoxidized bamboo lignin through systematic characterization employing Fourier transform infrared spectroscopy, hydrogen spectroscopy/two-dimensional heteronuclear single-quantum coherent nuclear magnetic resonance, quantitative phosphorus spectroscopy, and gel permeation chromatography. Lignin-based epoxy resins had an epoxy equivalent value of 350–400 g/mol and a weight-average molecular weight of 4853 g/mol. Studies on the curing kinetics revealed that polyetheramine (PEA-230) demonstrated the lowest apparent activation energy (46.2 kJ/mol), signifying its enhanced curing efficiency and potential for energy conservation. Mechanical testing indicated that the PEA-230 cured network demonstrated the maximum tensile strength (>25 MPa), whereas high-molecular-weight polyetheramine (PEA-2000) imparted enhanced elongation to the material. Lignin-based epoxy resins demonstrated superior heat stability. This study demonstrates the conversion of bamboo lignin into bio-based epoxy resins using a simple, environmentally friendly synthesis process, demonstrating the potential to reduce fossil resource use, efficiently use waste, develop sustainable thermosetting materials, and promote a circular bioeconomy. Full article

The design, synthesis, and application of composite materials based on manganese dioxide (MnO₂) for energy storage are pivotal in advancing efficient, sustainable, and high-performance energy storage systems. The MnO₂ is widely recognized for its abundance, low cost, environmental friendliness, and excellent electrochemical properties, making it a promising candidate for use in supercapacitors, batteries, fuel cells, and other energy storage systems. This study offers a comprehensive overview of how various materials influence the performance of MnO₂ as an energy storage medium. Specifically, the design of composite materials is examined with respect to morphological control, integration with conductive additives, doping strategies, and structural engineering, all of which impact the final material properties. Additionally, the influence of diverse synthetic techniques—including hydrothermal synthesis, electrochemical deposition, sol–gel processing, co-precipitation, and templating methods—is evaluated. The latest attempts through which the developed composites showcase improved structural stability, inherent conductivity, and electron mobility compared to the original first material are presented in this review article. The presented results have been quite promising for the synthesis of great-performing materials with improved electrochemical data compared to that of MnO₂ alone, competing with other significant energy storage materials. This review highlights future prospects for the development of state-of-the-art devices, large-scale production applications, and the use of environmentally friendly materials and methods. It is anticipated that this research will provide valuable insights to facilitate further improvements in performance and broaden the scope of practical applications in this rapidly evolving field of composite materials. Full article

We synthesized QM-AgNPs (Dianthus superbus L.-AgNPs, Qu Mai-AgNPs) by an economical and environmentally friendly method using Dianthus superbus L. extract as a reducing and stabilizing agent. The resulting QM-AgNPs were comprehensively characterized and evaluated for their antioxidant, cytotoxic, and antibacterial activities. Herein, TEM analysis revealed that the QM-AgNPs were predominantly spherical, polydisperse, and exhibited a core particle size ranging from 11 to 18 nm. In contrast, DLS analysis showed a larger hydrodynamic diameter (primarily 60–87 nm), reflecting the hydrated shell and surface biomolecular corona. The crystalline nature of QM-AgNPs was confirmed by XRD and SAED spectra while FTIR spectroscopy indicated the presence of functional groups from the plant extract that may contribute to nanoparticle stabilization. Functional assessments demonstrated that QM-AgNPs exhibited strong antioxidant activity, with efficient DPPH radical scavenging, and selective cytotoxicity against A549 cancer cells while sparing normal cells. Moreover, QM-AgNPs showed significant antibacterial activity against both Staphylococcus aureus (Gram-positive) and Escherichia coli (Gram-negative), likely due to membrane disruption and the leakage of intracellular contents. To explore practical applications, we developed a GEL@AgNPs coating system for the postharvest preservation of grapes. As a result, the reduced weight loss and decay rate suggest a potential role for QM-AgNPs in extending fruit freshness. Comprehensive shelf-life studies are planned to further substantiate the potential of QM-AgNPs as an effective material for active food packaging applications. Full article

Aiming at the problems of serious pavement temperature diseases, low efficiency and high loss of ice-breaking methods, high occupancy rate of waste tires and the low utilization rate and insufficient durability of rubber particles, this paper aims to improve the service level of roads and ensure the safety of winter pavements. A pavement material with high efficiency, low carbon and environmental friendliness for active snow melting and ice breaking is developed. Firstly, NaOH, NaClO and KH550 were used to optimize the treatment of rubber particles. The hydrophilic properties, surface morphology and phase composition of rubber particles before and after optimization were studied, and the optimal treatment method of rubber particles was determined. Then, the optimized rubber particles were used to replace the natural aggregate in the polyurethane gel mixture by the volume substitution method, and the optimum polyurethane gel dosages and molding and curing processes were determined. Finally, the influence law of the road performance of RPGM was compared and analyzed by means of an indoor test, and the ice-breaking effect of RPGM was explored. The results showed that the contact angles of rubber particles treated with three solutions were reduced by 22.5%, 30.2% and 36.7%, respectively. The surface energy was improved, the element types on the surface of rubber particles were reduced and the surface impurities were effectively removed. Among them, the improvement effect of the KH550 solution was the most significant. With the increase in rubber particle content from 0% to 15%, the dynamic stability of the mixture gradually increases, with a maximum increase of 23.5%. The maximum bending strain increases with the increase in its content. The residual stability increases first and then decreases with the increase in rubber particle content, and the increase ranges are 1.4%, 3.3% and 0.5%, respectively. The anti-scattering performance increases with the increase in rubber content, and an excessive amount will lead to an increase in the scattering loss rate, but it can still be maintained below 5%. The fatigue life of polyurethane gel mixtures with 0%, 5%, 10% and 15% rubber particles is 2.9 times, 3.8 times, 4.3 times and 4.0 times higher than that of the AC-13 asphalt mixture, respectively, showing excellent anti-fatigue performance. The friction coefficient of the mixture increases with an increase in the rubber particle content, which can be increased by 22.3% compared with the ordinary asphalt mixture. RPGM shows better de-icing performance than traditional asphalt mixtures, and with an increase in rubber particle content, the ice-breaking ability is effectively improved. When the thickness of the ice layer exceeds 9 mm, the ice-breaking ability of the mixture is significantly weakened. Mainly through the synergistic effect of stress coupling, thermal effect and interface failure, the bonding performance of the ice–pavement interface is weakened under the action of driving load cycle, and the ice layer is loosened, broken and peeled off, achieving efficient de-icing. Full article

Coalbed methane (CBM), a significant unconventional natural gas resource, holds a crucial position in China’s ongoing energy structure transformation. However, the inherent low permeability, high brittleness, and strong sensitivity of CBM reservoirs to drilling fluids often lead to severe formation damage during drilling operations, consequently impairing well productivity. To address these challenges, this study developed a novel low-damage, plugging, and anti-collapse water-based drilling fluid gel system (ACWD) specifically designed for coalbed methane drilling. Laboratory investigations demonstrate that the ACWD system exhibits superior overall performance. It exhibits stable rheological properties, with an initial API filtrate loss of 1.0 mL and a high-temperature, high-pressure (HTHP) filtrate loss of 4.4 mL after 16 h of hot rolling at 120 °C. It also demonstrates excellent static settling stability. The system effectively inhibits the hydration and swelling of clay and coal, significantly reducing the linear expansion of bentonite from 5.42 mm (in deionized water) to 1.05 mm, and achieving high shale rolling recovery rates (both exceeding 80%). Crucially, the ACWD system exhibits exceptional plugging performance, completely sealing simulated 400 µm fractures with zero filtrate loss at 5 MPa pressure. It also significantly reduces core damage, with an LS-C1 core damage rate of 7.73%, substantially lower than the 19.85% recorded for the control polymer system (LS-C2 core). Field application in the JX-1 well of the Ordos Basin further validated the system’s effectiveness in mitigating fluid loss, preventing wellbore instability, and enhancing drilling efficiency in complex coal formations. This study offers a promising, relatively environmentally friendly, and cost-effective drilling fluid solution for the safe and efficient development of coalbed methane resources. Full article

Aerogels have gained much interest in the last decades due to their specific properties, such as high porosity, high surface area, and low density, which have caused them to be used in multiple and varied fields. As the applicability of aerogels is tightly correlated to their morpho-structural features, special consideration must be allocated to the fabrication method. An emerging technique for producing nanostructured materials with tailored morphology and dimensions is represented by continuous-flow microfluidics. In this context, this work explores the synergic combination of aerogel-based materials with microfluidic synthesis platforms to generate advanced nanocomposite adsorbents for water decontamination. Specifically, this study presents the novel synthesis of a magnetic silica-based aerogel using a custom-designed 3D microfluidic platform, offering enhanced control over nanoparticle incorporation and gelation compared to conventional sol–gel techniques. The resulting gel was further dried via supercritical CO₂ extraction to preserve its unique nanostructure. The multi-faceted physicochemical investigations (XRD, DLS, FT-IR, RAMAN, SEM, and TEM) confirmed the material’s uniform morphology, high porosity, and surface functionalization. The HR-MS FT-ICR analysis has also demonstrated the advanced material’s adsorption capacity for various pesticides, suggesting its adequacy for further environmental applications. An exceptional 93.7% extraction efficiency was registered for triazophos, underscoring the potential of microfluidic synthesis approaches in engineering advanced, eco-friendly adsorbent materials for water decontamination of relevant organic pollutants. Full article

The emphasis on sustainable and environmentally friendly practices in geotechnical engineering has generated interest in alternative soil stabilizing techniques. The present study examines the application of xanthan gum (XG) and guar gum (GG) to enhance the strength of a sand–bentonite composite and explore their potential for use as landfill liners or impervious barriers. The mixtures, consisting of 25% bentonite and 75% sand, were treated with XG and GG concentrations of different percentages (0.5%, 1%, 2%, and 3% by dry mass). The test results indicated that a 2% addition was optimal for both biopolymers. Using this optimum value of XG and GG significantly increased the unconfined compressive strength (UCS) by almost 3-fold compared to the strength of untreated samples. Meanwhile, XG demonstrated a slightly higher impact on strength attributed to its robust gel-forming and binding properties. Comparisons between the two biopolymers highlighted XG’s superior performance, with UCS improvements of up to 20% over GG-treated samples. These results underscore the potential of biopolymers as effective, sustainable alternatives to traditional stabilizers, providing both mechanical enhancements and environmental benefits. The present study contributes valuable insights into green soil stabilization techniques, supporting the development of more sustainable construction practices. Fourier Transform Infrared Spectroscopy (FTIR) was conducted to analyze the chemical interactions between sand–bentonite mixtures and biopolymers, which possibly provide insights into the bonding mechanisms responsible for the observed improvements in mechanical and volumetric behavior. Full article

The widespread phase-out of long-chain per- and poly-fluoroalkyl substances (PFASs) has created an urgent need for durable, fluorine-free water-repellent finishes that match the performance of legacy chemistries while minimising environmental impact. Here, the performance of an eco-friendly hybrid organic–inorganic treatment obtained by the in situ hydrolysis–condensation of triethoxy(octyl)silane (OS) in an amino-terminated polydimethylsiloxane (APT-PDMS) aqueous dispersion was investigated. The sol was applied to plain-weave cotton and polyester by a pad-dry-cure process and benchmarked against a commercial fluorinated finish. Morphology and chemistry were characterised by SEM–EDS, ATR-FTIR, and Raman spectroscopy; wettability was assessed by static contact angle, ISO 4920 spray ratings, and AATCC 193 water/alcohol repellence; and durability, handle, and breathability were evaluated through repeated laundering, bending stiffness, and water-vapour transmission rate measurements. The silica/PDMS coating formed a uniform, strongly adherent nanostructured layer conferring static contact angles of 130° on cotton and 145° on polyester. After five ISO 105-C10 wash cycles, the treated fabrics still displayed a spray rating of 5/5 and AATCC 193 grade 7, outperforming or equalling the fluorinated control, while causing ≤5% loss of water-vapour permeability and only a marginal increase in bending stiffness. These results demonstrate that the proposed one-step, water-borne sol–gel process affords a sustainable, industrially scalable route to high-performance, durable, water-repellent finishes for both natural and synthetic textiles, offering a viable alternative to PFAS-based chemistry for outdoor apparel and technical applications. Full article

Chestnut blight, caused by Cryphonectria parasitica (Murrill) M.E. Bar, is a destructive fungal disease threatening chestnut cultivation and production. In response to the limitations of chemical control, biological control using antagonistic microbes has gained increasing attention. A rhizosphere-derived bacterium, strain D39, was isolated from healthy chestnut trees and identified as Bacillus amyloliquefaciens based on morphological characteristics and the phylogenetic analysis of 16S rRNA and gyrA genes. The antifungal activity of strain D39 against C. parasitica was evaluated using dual-culture and double-layer Oxford cup assays. The strain exhibited broad-spectrum and stable antagonistic effects and harbored five key genes associated with antimicrobial compound biosynthesis (srfAA, ituC, fenD, bmyB, and bacA), as confirmed by PCR. A 145 kDa extracellular protein with strong antifungal activity was extracted and purified by ammonium sulfate precipitation, DEAE ion-exchange chromatography, and Sephadex G-75 gel filtration. LC-MS analysis identified the protein as a serine peptidase belonging to the S8 family, and its structure was predicted using multiple bioinformatic tools. In pot experiments, treatment with the strain D39 significantly reduced disease severity, achieving control efficiencies of 66.07% and 70.89% at 10 and 20 days post-inoculation, respectively. These results demonstrate that B. amyloliquefaciens D39 has strong potential as a biocontrol agent against chestnut blight, offering an effective and environmentally friendly alternative for disease management. Full article

It has been demonstrated that the traditional hydrometallurgical method is still economically viable in several industrial applications such as Bayer, Boix, Platsol, Sherrit-Gordon, and so on. The conventional extraction technique of valuable metals from their ores using an aqua medium has several challenges. The following can be listed for the illustration of this: (1) Inorganic acids used during the leaching process have been proven to be non-environmentally friendly and ready to lead to non-selective processes in general, except in rare cases used in alkaline environments. (2) Special linings are required in the reactors used due to the corrosive impact of acids such as HCl and H₂SO_4, especially when leaching at high temperatures, rendering all processes costly. (3) Practically, using inorganic acids while leaching samples containing amorphous silicate phases leads to gel formation. Solvometallurgy overcomes these challenges by substituting the aqueous phase for other polar solvents, such as polar molecular organic or ionic solvents. The advantage of this substitution lies in the ability to manipulate metal ion distribution using solvents with varying solvation properties. This review examines the potential of solvometallurgical processes (solvoleaching) over conventional hydrometallurgy as viable alternatives for metal extraction from sulfide ores. It highlights the key distinctions between hydrometallurgy and solvometallurgy while emphasizing the potential economic and environmental advantages solvometallurgy offers. Full article

Red mud (RM) is a strongly alkaline waste residue produced during alumina production, and its high alkali and fine particle characteristics are prone to cause soil, water, and air pollution. Phosphogypsum (PG), as a by-product of the wet process phosphoric acid industry, poses a significant risk of fluorine leaching and threatens the ecological environment and human health due to its high fluorine content and strong acidic properties. In this study, RM-based cemented paste backfill (RCPB) based on the synergistic curing of PG and ordinary Portland cement (OPC) was proposed, aiming to achieve a synergistic enhancement of the material’s mechanical properties and fluorine fixation efficacy by optimizing the slurry concentration (63–69%). Experimental results demonstrated that increasing slurry concentration significantly improved unconfined compressive strength (UCS). The 67% concentration group achieved a UCS of 3.60 MPa after 28 days, while the 63%, 65%, and 69% groups reached 2.50 MPa, 3.20 MPa, and 3.40 MPa, respectively. Fluoride leaching concentrations for all groups were below the Class I groundwater standard (≤1.0 mg/L), with the 67% concentration exhibiting the lowest leaching value (0.6076 mg/L). The dual immobilization mechanism of fluoride ions was revealed by XRD, TGA, and SEM-EDS characterization: (1) Ca²⁺ and F⁻ to generate CaF₂ precipitation; (2) hydration products (C-S-H gel and calixarenes) immobilized F⁻ by physical adsorption and chemical bonding, where the alkaline component of the RM (Na₂O) further promotes the formation of sodium hexafluoroaluminate (Na₃AlF₆) precipitation. The system pH stabilized at 9.0 ± 0.3 after 28 days, mitigating alkalinity risks. High slurry concentrations (67–69%) reduced material porosity by 40–60%, enhancing mechanical performance. It was confirmed that the synergistic effect of RM and PG in the RCPB system could effectively neutralize the alkaline environment and optimize the hydration environment, and, at the same time, form CaF₂ as well as complexes encapsulating and adsorbing fluoride ions, thus significantly reducing the risk of fluorine migration. The aim is to improve the mechanical properties of materials and the fluorine-fixing efficiency by optimizing the slurry concentration (63–69%). The results provide a theoretical basis for the efficient resource utilization of PG and RM and open up a new way for the development of environmentally friendly building materials. Full article