Search Results (24)

Evaporative cooling (EC) offers an energy-efficient alternative to direct expansion (DX) cooling but suffers from high water consumption. This limitation can be mitigated by pre-cooling incoming fresh air using cooler exhaust air via energy recovery. This study presents and optimizes a solar-driven EC system integrated with underfloor air distribution (UFAD) to enhance thermal comfort and minimize water use in a temporary office in Riyadh’s arid climate. A 3D CFD model was developed and validated against published data to simulate indoor airflow, providing data for thermal comfort evaluation using the predicted mean vote model in cases with and without energy recovery. A year-round hourly energy analysis revealed that the solar-driven EC-UFAD system reduces grid power consumption by 93.5% compared to DX-based UFAD under identical conditions. Energy recovery further cuts annual EC water usage by up to 31.3%. Operational costs decreased by 84% without recovery and 87% with recovery versus DX-UFAD. Full article

In response to the significant increase in cooling needs for the built environment due to climate change, hybrid air conditioning units can provide energy efficient alternatives to vapor compression systems. This paper reviews the reported energy performance of integrated air conditioning systems consisting of three types of hybrid options: direct expansion (DX) combined with evaporative cooling, DX with desiccant, and evaporative cooling combined with desiccant. In addition, the reported analyses of integrating these hybrid systems with phase change materials (PCMs) and/or photovoltaic (PV) systems are considered. The evaluated analyses generally confirm that integrated air conditioning systems offer substantial energy saving potential compared to traditional vapor compression cooling units, resulting in substantial economic and environmental benefits. Specifically, hybrid systems can reduce the annual energy consumption for space cooling by 87% compared to traditional air conditioning units. This review analysis indicates that hybrid systems can have a coefficient of performance (COP) ranging from 6 to 16 compared to merely 3 to 5 for conventional systems. Additionally, liquid desiccant cooling systems have reported notable improvements in dehumidification efficiency and energy savings, with payback periods as low as three years. Future work should focus more on real-building applications and on conducting more comprehensive cost–benefit analyses, especially when integrating more than two technologies together. Full article

Integrated thermal management system (ITMS) technology for electric vehicles (EV) has become a major industry research direction. However, R290 refrigerants are still not applied on a large scale in EVs. Therefore, we developed a suitable thermal management system for R290 in this study. This architecture adapts an unusual indirect design, which can coordinate the heat between the air conditioner, battery pack, and electric motor. We focused on heat pump air conditioning systems for EV thermal management; thus, we carried out the performance analysis of R290 under the cooling and heating conditions of our ITMS through an experimental approach. The current study explores various aspects affecting the performance of heat-pump air conditioners: refrigerant charge, electronic expansion valve (EXV) opening, compressor speed, and performance between R290 and R134a under different external temperatures. We aim to improve cooling and heating efficiencies. Among these parameters, the EXV opening and compressor speed have the greatest impact on the performance of the ITMS, as evidenced by the optimal EXV opening and lower compressor speed to maximize the coefficient of performance (COP) and increase the heat transfer rate. In addition, this study has shown that, compared to an ITMS equipped with R134a, R290 has a smaller refrigerant charge, better heat transfer rate and COP under heating conditions, and similar performance under cooling conditions. Full article

According to extant Italian legislation implementing the Renewable Energy Directive, the mandatory renewable quota for a new building is 60% referring to a single service (e.g., heating during winter) or to multiple services (e.g., heating during winter and air conditioning during summer), depending on which services are actually present. The obligation to satisfy this minimum value often leads heating and ventilation plant designers to provide heat pump systems in industrial buildings, typically air/water or direct expansion type coupled with air terminals (air heaters or ventilation units) or radiant floors. The question is: Is this always the most advantageous option for industrial buildings? A typical industrial building was modeled by Trnsys^® in two different climates. Based on the calculated thermal heating loads, the condensing radiant tubes and heat pump coupled with the air heaters systems were analyzed through dynamic simulation, evaluating their performance from an energy, environmental impact, and economic point of view. The analysis carried out revealed that a heat pump system is not always the most advantageous solution depending on the climate, the characteristics of the building (less or more thermal insulation, which corresponds to existing buildings rather than new ones), and the size of the photovoltaics system eventually installed on the roof. Full article

This study introduces a novel direct expansion air conditioning (DX AC) system with three evaporators (DX-TE) to enhance indoor temperature and humidity control. Operating in two modes, the DX-TE system provides variable cooling output, adapting to fluctuating indoor cooling loads while maintaining uniform air supply. Experimental and simulation studies were conducted to investigate the system’s operational characteristics. An experimental setup was established to obtain preliminary steady-state data, followed by the development and validation of a steady-state mathematical model. Simulation studies were then performed to optimize the evaporator sizes. The results indicate that the DX-TE system delivers variable cooling capacities at a constant compressor speed and airflow rate, outperforming conventional variable frequency DX AC systems in cooling and dehumidification. The evaporator area ratio significantly impacts the system’s performance, with smaller ratios yielding a larger output range. As the area ratio increases from 1:1 to 1:3, the cooling capacity range in Modes 1 and 2 increases by 33.6% and 14.3%, respectively, while the dehumidification range expands by 58.6% and 51.69%. Full article

In order to improve the air pollution problem in northern China in winter, coal-to-electricity (CtE) projects are being vigorously implemented. Although the CtE project has a positive effect on alleviating air pollution and accelerating clean energy development, the economic benefits of electric heating are currently poor. In this study, a system based on vehicle-to-home (V2H) and photovoltaic power generation that can effectively improve the benefits of CtE projects is proposed. First, a V2H-based village microgrid is proposed. The winter temperature and direct radiation of the Beijing CtE project area are analyzed. Extreme operating conditions and typical operating conditions are constructed for potential analysis. After that, a bi-layer optimization model for energy management considering travel characteristics is proposed. The upper layer is a village-level microgrid energy-dispatching model considering meeting the heating load demand, and the lower layer is a multi-vehicle energy distribution model considering the battery degradation. The results show that the distribution grid expansion capacity of the electric heating system based on V2H and PV generation is reduced by 45.9%, and the residents’ electricity bills are reduced by 68.5%. The consumption of PV can be completed. This study has effectively increased the benefits of electric heating in northern China during winter. This helps the CtE project to be further promoted without leading to large subsidies from the government and the State Grid. Full article

The Energy Efficiency Directive (EED, Directive 2012/27/EU) has made mandatory the installation of individual metering systems in the case of buildings with centralized heating/cooling and hot water sources (multi-apartment and multi-purpose buildings), provided it is economically and technically feasible. Individual metering of heating/cooling systems is mainly based on thermal energy meters (TEM), which are widely used for direct metering in heating applications. On the other hand, direct metering of energy consumption in cooling systems still represents a challenge, given the different types of cooling units and the lack of regulations from the technical and legal points of view. In this context, this paper briefly overviews the available centralized cooling systems and the possible solutions for metering and sub-metering, which depend on the specific application. Vapour Compression Refrigeration (VCR) systems are spreading worldwide for air conditioning applications. Particular attention has been paid to the direct metering of cooling energy and specifically to refrigerant flow rate measurement, which represents a critical issue because of the small-diameter pipes and the different thermodynamic properties of the fluid used. Thus, an experimental campaign has been developed and carried out in order to compare a clamp-on ultrasonic flowmeter with a more accurate Coriolis one in a direct expansion (DE) system. The experimental tests have been performed at two different temperature conditions, showing a relative error in the mass flow rate measurements within ±10%. Full article

A hybrid air conditioning system, which is composed of a novel gravity-assisted heat pipe (GAHP)-based indirect evaporative cooler (IEC) and direct expansion (DX) cooling coil, is proposed and investigated here. After developing a mathematical model to describe the performance of the GAHP-based IEC, the hybrid system is evaluated during the cooling design day for providing thermal comfort for an office building in Poland. The results are obtained and compared with the combination of a rotary heat exchanger (RHE) and DX cooling coil as the conventional hybrid system. The comparison is performed by analyzing cooling capacity, electricity consumption, and coefficient of performance profiles, which describe the technical, energy, and efficiency aspects, respectively. The results show that the GAHP-based IEC hybrid system is able to enhance the energy performance significantly compared to the conventional one. The proposed hybrid HVAC system improves COP by 39.2% and reduces electricity consumption by 45.0%, according to the design-day of 24 August and the outdoor temperature of 30 °C. As a result, the total operating cost for the assumed cooling season is reduced by 51.7%. Full article

For a comfortable thermal environment, the main parameters are indoor air humidity and temperature. These parameters are strongly coupled, causing the need to search for multivariable control alternatives that allow efficient results. Therefore, in order to control both the indoor air humidity and temperature for direct expansion (DX) air conditioning (A/C) systems, different controllers have been designed. In this paper, a discrete-time neural inverse optimal control scheme for trajectories tracking and reduced energy consumption of a DX A/C system is presented. The dynamic model of the plant is approximated by a recurrent high-order neural network (RHONN) identifier. Using this model, a discrete-time neural inverse optimal controller is designed. Unscented Kalman filter (UKF) is used online for the neural network learning. Via simulation the scheme is tested. The proposed approach effectiveness is illustrated with the obtained results and the control proposal performance against disturbances is validated. Full article

This paper proposes the analysis of real monitored data for evaluating the relationship between occupants’ comfort conditions and the energy balance inside an existing, nearly zero-energy building under different operational strategies for the heating, ventilation, and air-conditioning system. During the wintertime, the adaptive comfort approach is applied for choosing the temperature setpoint when an air-to-air heat pump provides both heating and ventilation. The results indicate that in very insulated buildings with high solar gains, the setpoint should be decided taking into consideration both the solar radiation and the outdoor temperature. Indeed, when the room has large glazed surfaces, the solar radiation can also guarantee acceptable indoor conditions when a low setpoint (e.g., 18.7 °C) is considered. The electricity consumption can be reduced from 17% to 43% compared to a conventional setpoint (e.g., 20 °C). For the summertime, the analysis suggests the adoption of a dynamic approach that should be based on the outdoor conditions and differentiated according to room characteristics. Considering the indoor comfort and the maximization of renewable integration, the direct expansion system has better performance than the heat pump; this last system should be integrated with a pre-handling unit to be energy convenient. Full article

Efficient air cooling systems for hot climatic conditions, such as southern Europe, are required. Regenerative indirect evaporative cooler (RIEC) and desiccant regenerative indirect evaporative cooler (DRIEC) could be interesting alternatives to direct expansion conventional systems (DX). The main objective of this work was to evaluate the seasonal performance of three air cooling systems in terms of thermal comfort, ventilation and energy consumption. DRIEC was the recommended system to serve a standard classroom in terms of thermal comfort and RIEC in terms of ventilation and energy consumption. Full article

Efficient air-cooling systems for hot climatic conditions, such as Southern Europe, are required in the context of nearly Zero Energy Buildings, nZEB. Innovative air-cooling systems such as regenerative indirect evaporative coolers, RIEC and desiccant regenerative indirect evaporative coolers, DRIEC, can be considered an interesting alternative to direct expansion air-cooling systems, DX. The main aim of the present work was to evaluate the seasonal performance of three air-cooling systems in terms of air quality, thermal comfort and energy consumption in a standard classroom. Several annual energy simulations were carried out to evaluate these indexes for four different climate zones in the Mediterranean area. The simulations were carried out with empirically validated models. The results showed that DRIEC and DX improved by 29.8% and 14.6% over RIEC regarding thermal comfort, for the warmest climatic conditions, Lampedusa and Seville. However, DX showed an energy consumption three and four times higher than DRIEC for these climatic conditions, respectively. RIEC provided the highest percentage of hours with favorable indoor air quality for all climate zones, between 46.3% and 67.5%. Therefore, the air-cooling systems DRIEC and RIEC have a significant potential to reduce energy consumption, achieving the user’s thermal comfort and improving indoor air quality. Full article

This study provides a general procedure to generate a direct expansion (DX) cooling coil system for a roof top unit (RTU), which is a typical heating ventilation and air-conditioning (HVAC) system for commercial buildings in the United States. Experimental data from a full-scale unoccupied 2-story commercial building is used for the HVAC modeling. The regression for identifying the model coefficients was carried out with multiple stages, and the results were validated with measured data. The model’s applicability was evaluated with multiple case studies, including a building energy simulation (BES) program validation, model-based predictive control (MPC), and fault diagnostics and detection (FDD). Full article

When using a certain type of Heating, Ventilation & Air Conditioning (HVAC) systems, it is primary to obtain their steady-state operating behaviors for achieving a better indoor thermal environment. This paper reports a development of a white-box-based dynamic model for a direct expansion (DX) air conditioning (A/C) system to predict its steady-state operating performance under variable speed operation. The established model consists of five sub-models, i.e., a compressor, an electronic expansion valve, an evaporator, a condenser and a conditioned space. Each sub-model was developed based on partial lumped parameter approach. Using the available data generated from an experimental DX A/C system, both transient and steady-state behaviors predictions agreed well with the experimental ones. With the help of the validated white-box model, the inherent steady-state operating performance expressed in terms of the relationship among total cooling capacity (TCC), equipment sensible heat ratio (E SHR) and coefficient of performance (COP) under various speed combinations of compressor and supply fan were further examined. The results show that a higher COP could be achieved when the DX A/C system was operated at a higher fan speed or a lower compressor speed for dealing with a larger required E SHR. This model could be helpful for A/C system design and controller development. Full article

Evaporative cooling can be integrated into fresh-air-handling units, to reduce cooling demand. This study considers a hybrid fresh-air-handling unit which incorporates a vapor-compression cooling cycle and indirect evaporative cooling to condition an ambient primary airstream to a desired supply air state. The cooling effects of using various modes (vapor compression only; direct expansion with mist; direct expansion with water shower; and direct expansion with mist and water shower) are compared when the fresh-air-handling unit operates in harsh (hot and humid) climatic conditions experienced in Qatar. Experimental analysis is based on actual ambient conditions measured from August 2018 to July 2019. It is found that the best-performing wet mode of operation saves more than 60% of the energy required by a conventional direct expansion cooling system operating under the same ambient conditions. In hot, dry conditions, the coefficient of performance of the fresh-air-handling unit when using the indirect evaporative mode of operation is double the coefficient of performance when operating with direct expansion mode only. Full article