Search Results (576)

In response to increasingly stringent emission regulations, low-carbon fuels have received significant attention as sustainable energy sources for internal combustion engines. This study investigates four representative low-carbon fuels, methane, methanol, hydrogen, and ammonia, by systematically summarizing their combustion characteristics and emission profiles, along with a review of existing after-treatment technologies tailored to each fuel type. For methane engines, unburned hydrocarbon (UHC) produced during low-temperature combustion exhibits poor oxidation reactivity, necessitating integration of oxidation strategies such as diesel oxidation catalyst (DOC), particulate oxidation catalyst (POC), ozone-assisted oxidation, and zoned catalyst coatings to improve purification efficiency. Methanol combustion under low-temperature conditions tends to produce formaldehyde and other UHCs. Due to the lack of dedicated after-treatment systems, pollutant control currently relies on general-purpose catalysts such as three-way catalyst (TWC), DOC, and POC. Although hydrogen combustion is carbon-free, its high combustion temperature often leads to elevated nitrogen oxide (NO_x) emissions, requiring a combination of optimized hydrogen supply strategies and selective catalytic reduction (SCR)-based denitrification systems. Similarly, while ammonia offers carbon-free combustion and benefits from easier storage and transportation, its practical application is hindered by several challenges, including low ignitability, high toxicity, and notable NO_x emissions compared to conventional fuels. Current exhaust treatment for ammonia-fueled engines primarily depends on SCR, selective catalytic reduction-coated diesel particulate filter (SDPF). Emerging NO_x purification technologies, such as integrated NO_x reduction via hydrogen or ammonia fuel utilization, still face challenges of stability and narrow effective temperatures. Full article

Compression–ignition engines emit particulate matter (PM) (soot), prompting the widespread use of diesel particulate filters (DPFs) in the automotive sector. An alternative method for PM reduction involves the use of ultrasonic waves to disperse and modify the structure of exhaust particles. This article presents experimental results of the effects of ultrasonic emitter parameters, including the number, arrangement, and power, along with the engine speed, on the exhaust smoke density. Tests were conducted on a laboratory prototype equipped with six ultrasonic emitters spaced 0.17 m apart. The exhaust source was a diesel engine from a construction excavator, based on the MTZ-80 tractor design, delivering 80 HP and a displacement of 4750 cm³. A regression model was developed to describe the relationship between the engine speed, emitter power and spacing, and smoke density. The optimal configuration was found to involve an emitter power of 319.35 W and a spacing of 1.361 m for a given engine speed. Under the most effective conditions—an engine speed of 1500 rpm, six active emitters, and a total power of 600 W—smoke emissions were reduced by 18%. These findings support the feasibility of using ultrasonic methods as complementary or alternative exhaust gas filtration techniques for non-road diesel engines. Full article

In recent decades, environmental requirements for reducing the toxic components emitted from vehicle exhausts have decreased drastically. Technologies for after-treatment of diesel vehicle emissions are being improved continuously in order to meet increasingly stringent regulations. Passenger cars are a significant source of air pollution, especially in urban areas. The EU has decided to phase out internal combustion engines. Stricter Real Driving Emissions (RDE) testing procedures have also been introduced, aiming to assess the emissions of nitrogen oxides (NO_x) and particle number (PN). The present work investigates the interaction between performance and smoke emissions of a diesel vehicle on a pre-established route in an urban environment with an everyday (normal) driving style. The results showed that when the vehicle is technically sound and meets its technical specifications, smoke emissions are within normal limits. Full article

Researchers have tended to blend isopropanol (IPA) with other fuels in diesel engines to reduce emissions and improve performance. However, low-reactivity controlled compression ignition via port injection at a low cetane number results in a well-mixed charge of low-reactivity fuel, air, and recirculated exhaust gas (EGR). This study’s novel approach combines critical elements, such as the mass fraction of port-injected IPA, EGR ratio, and charge temperature, to improve combustion characteristics and lessen emissions from a diesel engine. The results demonstrated that the injection of IPA and the installation of EGR at the inlet reduced NO_x, smoke, and PM_2.5. On the contrary, HC and CO increased with the port-injection of IPA and EGR. Preheating air at the inlet can suppress the emissions of HC and CO. Under 1500 rpm and 60% load, when compared to diesel at the same EGR ratio and charge temperature, the maximum smoke decrease rate (26%) and PM_2.5 decrease rate (21%) occur at 35% IPA, 45 °C, and 10% EGR, while the maximum NO_x decrease rate (24%) occurs at 35% IPA, 60 °C, and 20% EGR. These findings support the novelty of the research. Conversely, it modestly increased CO and HC emissions. However, port-injecting IPA increased thermal efficiency by up to 24% at 60 °C, 1500 rpm, and 60% load with EGR. Full article

Progressive research on reducing engine emissions is highly valued due to the emissions’ significant environmental and health impacts. This comprehensive comparative study examines the catalytic efficiency of manganese (Mn) and cerium silica (Ce-Si) synthesis catalyst-based molds in a diesel engine using a selective catalytic reduction (SCR) technique with diesel and diesel–plastic oil blend (DPB) (B50). In addition to Fourier transform infrared spectroscopy (FTIR) studies, X-ray diffraction (XRD), scanning electron microscopy (SEM), and the Brunauer–Emmett–Teller (BET) method are utilized to characterize the produced molds before and after exhaust gas passes. The Ce-Si-based mold demonstrates superior redox capacity, better adsorption capacity, and better thermal stability, attributed to enhanced oxygen storage and structural integrity compared to the Mn-based mold. Under minimum load conditions, nitrogen oxide (NO) reduction efficiency peaks at 80.70% for the Ce-Si-based mold in the SCR treatment with DPB fuel. Additionally, significant reductions of 86.84%, 65.75%, and 88.88% in hydrocarbon (HC), carbon monoxide (CO), and smoke emissions, respectively, are achieved in the SCR treatment under optimized conditions. Despite a wide temperature range, Ce-Si-based mold promotes high surface area and superior gas diffusion properties. Overall, the Ce-Si-based mold provides efficient emission control in diesel engines, which paves a path for developing better environmental sustainability. The outcomes contribute to advancing environmental sustainability by supporting the achievement of SDGs 7, 11, and 13. Full article

Alternative fuels to fossil fuels have been a focus of research since the 1980s, due to the oil crisis. Biofuels for diesel engines are obtained from various types of fats, primarily vegetable oils. Soybean and rapeseed oil are mainly used to produce biofuels. The aim of the research undertaken was to compare the performance characteristics of a 1.3 JTD engine fueled with methyl esters from hemp compared to biofuels made from rapeseed and fossil fuels. Energy parameters and exhaust emissions were measured. The fuels used were 100% biofuels obtained from vegetable oils by transesterification using methanol and KOH. It was shown to be possible to use HME (hemp methyl esters) biofuels as an alternative fuel to RME (rapeseed methyl esters) or DF (diesel fuel) without significant changes in engine performance. The density and heat of combustion of such fuels results in a 6% reduction in power and 17% in NO_x emissions, as well as a decrease in HC (hydrocarbons), CO₂, and smoke emissions. Full article

In the era of depletion of fossil fuels, there is an intensive search for renewable fuels for the internal combustion engine, which is the most efficient thermal machine in the power range of several kW to several MW. Hence, this article discusses the results of research on the combustion of renewable fuels such as hydrotreated vegetable oil (HVO) and the rapeseed methyl ester (RME) with the addition of hydrogen, injected in its gaseous form into the intake manifold. The thermodynamic analysis presented in the article discusses progress in the combustion process of these fuels depending on the hydrogen content. The parameters for diesel fuel combustion are given as a reference point. Based on the obtained results, one can conclude that adding hydrogen increases the maximum combustion pressure in the cylinder and significantly accelerates the combustion process in the premixed combustion phase, thus reducing the share of the diffusion combustion phase. This significantly affects exhaust toxic emissions. In connection with this, a shortening of the flame kernels development phase was observed, calculated as the time expressed by the crank angle, to release heat of 10%, and a slight extension of the main combustion phase, managed as the period of the heat released from 10 to 90% was observed as well. Full article

Although the transition to electric vehicles (EVs) is well underway and expected to continue in global car markets, most vehicles on the world’s roads will be powered by internal combustion engine vehicles (ICEVs) and fossil fuels for the foreseeable future, possibly well past 2050. Thus, good environmental performance and effective emission control of ICE vehicles will continue to be of paramount importance if the world is to achieve the stated air and climate pollution reduction goals. In this study, we review 228 publications and identify four main issues confronting these objectives: (1) cheating by vehicle manufacturers, (2) tampering by vehicle owners, (3) malfunctioning emission control systems, and (4) inadequate in-service emission programs. With progressively more stringent vehicle emission and fuel quality standards being implemented in all major markets, engine designs and emission control systems have become increasingly complex and sophisticated, creating opportunities for cheating and tampering. This is not a new phenomenon, with the first cases reported in the 1970s and continuing to happen today. Cheating appears not to be restricted to specific manufacturers or vehicle types. Suspicious real-world emissions behavior suggests that the use of defeat devices may be widespread. Defeat devices are primarily a concern with diesel vehicles, where emission control deactivation in real-world driving can lower manufacturing costs, improve fuel economy, reduce engine noise, improve vehicle performance, and extend refill intervals for diesel exhaust fluid, if present. Despite the financial penalties, undesired global attention, damage to brand reputation, a temporary drop in sales and stock value, and forced recalls, cheating may continue. Private vehicle owners resort to tampering to (1) improve performance and fuel efficiency; (2) avoid operating costs, including repairs; (3) increase the resale value of the vehicle (i.e., odometer tampering); or (4) simply to rebel against established norms. Tampering and cheating in the commercial freight sector also mean undercutting law-abiding operators, gaining unfair economic advantage, and posing excess harm to the environment and public health. At the individual vehicle level, the impacts of cheating, tampering, or malfunctioning emission control systems can be substantial. The removal or deactivation of emission control systems increases emissions—for instance, typically 70% (NO_x and EGR), a factor of 3 or more (NO_x and SCR), and a factor of 25–100 (PM and DPF). Our analysis shows significant uncertainty and (geographic) variability regarding the occurrence of cheating and tampering by vehicle owners. The available evidence suggests that fleet-wide impacts of cheating and tampering on emissions are undeniable, substantial, and cannot be ignored. The presence of a relatively small fraction of high-emitters, due to either cheating, tampering, or malfunctioning, causes excess pollution that must be tackled by environmental authorities around the world, in particular in emerging economies, where millions of used ICE vehicles from the US and EU end up. Modernized in-service emission programs designed to efficiently identify and fix large faults are needed to ensure that the benefits of modern vehicle technologies are not lost. Effective programs should address malfunctions, engine problems, incorrect repairs, a lack of servicing and maintenance, poorly retrofitted fuel and emission control systems, the use of improper or low-quality fuels and tampering. Periodic Test and Repair (PTR) is a common in-service program. We estimate that PTR generally reduces emissions by 11% (8–14%), 11% (7–15%), and 4% (−1–10%) for carbon monoxide (CO), hydrocarbons (HC), and oxides of nitrogen (NO_x), respectively. This is based on the grand mean effect and the associated 95% confidence interval. PTR effectiveness could be significantly higher, but we find that it critically depends on various design factors, including (1) comprehensive fleet coverage, (2) a suitable test procedure, (3) compliance and enforcement, (4) proper technician training, (5) quality control and quality assurance, (6) periodic program evaluation, and (7) minimization of waivers and exemptions. Now that both particulate matter (PM, i.e., DPF) and NO_x (i.e., SCR) emission controls are common in all modern new diesel vehicles, and commonly the focus of cheating and tampering, robust measurement approaches for assessing in-use emissions performance are urgently needed to modernize PTR programs. To increase (cost) effectiveness, a modern approach could include screening methods, such as remote sensing and plume chasing. We conclude this study with recommendations and suggestions for future improvements and research, listing a range of potential solutions for the issues identified in new and in-service vehicles. Full article

With the implementation of China’s low-sulfur fuel policy, the characteristics of volatile organic compounds (VOCs) emitted from ship exhausts have changed significantly, and the influence of these emissions on the local atmosphere of port cities needs to be evaluated. In this study, the characteristics of localized source profiles of ship-emitted VOCs with respect to different ship types, fuel types, and engine operating conditions were analyzed in Guangzhou Port. Oxygenated VOCs (OVOCs) dominated in ferry (91.1%), cargo ship (87.0%), and tugboat (54.4% ± 7.9%) emissions (diesel fuel), while alkanes (56.3% ± 1.6%) and alkenes (36.0% ± 0.9%) were major species in multi-purpose ship (LNG fuel) emissions. These results suggest the dominance of OVOCs in the exhaust emissions of diesel-type ships and the prominent difference in ship-emitted VOCs between diesel and LNG fuel ships, which also influenced the emission characteristics of VOCs from main and auxiliary engines. Based on the measured source profiles, ship emissions contributed 18.2% ± 0.8% (summer), 8.7% ± 1.9% (winter), 6.0% ± 1.1% (spring), and 5.6% ± 1.7% (autumn) to VOCs in the port area, and 7.8% ± 1.5% in July and 5.0% ± 0.5% in September in the urban area. An air mass trajectory analysis revealed that the south wind transported the ship exhaust emissions to the port area and inland urban area, which explained the higher contributions of ship emissions in summer and more ship emissions received in the port area than in the urban area. Therefore, estimating the influence of ship emissions on ambient air quality in port cities requires integrating local ship source profiles, locations, and meteorological conditions. This study provides insights into the ship-emitted VOC characteristics given China’s low-sulfur fuel policy and their differential contributions to urban atmospheric VOCs. Full article

Dimethyl carbonate (DMC) and polyoxymethylene dimethyl ethers (PODE also known as OME) are possible diesel additives that can be produced sustainably using green methanol. DMC can be produced from CO₂ and methanol, while PODE can be produced from methanol and formaldehyde. In this study both DMC and PODE were investigated as drop-in diesel fuel additives regarding material compatibility, injection behavior, as well as particle and exhaust emissions. Both DMC and PODE are known to be incompatible with certain materials used as seals in the fuel injection system. Therefore, the material compatibility of both neat DMC and PODE as well as blends with B0 was investigated, with both PFTE and FFKM showing good compatibility. The hydraulic injection behavior of DMC–diesel and PODE–diesel blends was investigated experimentally, showing the need for compensating injection quantities for DMC and PODE blends to match neat diesel power output due to their lower calorific values. Energetic compensation can be achieved by higher injection pressures or longer injection durations. Engine tests have been conducted with both DMC–diesel and PODE–diesel blends, demonstrating the potential to mitigate the particle–NO_X trade-off. Full article

This study presents a comprehensive analysis of combustion mechanisms and emission formation in marine diesel engines using biodiesel blends through experimental validation and computational fluid dynamics simulation using Matlab 2024a. Two marine engines were tested—YANMAR 6HAL2-DTN (200 kW, 1200 rpm) and Niigatta Engineering 6L34HX (2471 kW, 600 rpm)—with biodiesel ratios B0, B20, B50, and B100 at loads from 10% to 100%. The methodology combines detailed experimental measurements of exhaust emissions, fuel consumption, and engine performance with three-dimensional CFD simulations employing k-ε RNG turbulence model, Kelvin–Helmholtz–Rayleigh–Taylor droplet breakup model, and extended Zeldovich mechanism for NOx formation modeling. Key findings demonstrate that biodiesel’s oxygen content (10–12% by mass) increases maximum combustion temperature by 25 °C at 50% load, resulting in NOx emissions increase of 5–13% across all loads. Conversely, CO emissions decrease by 7–10% due to enhanced oxidation reactions. CFD analysis reveals that B100 exhibits 12% greater spray penetration depth, 20% larger Sauter Mean Diameter, and 20–25% slower evaporation rate compared to B0. The thermal Zeldovich mechanism dominates NOx formation (>90%), with prompt-NO and fuel-NO contributions increasing from 6.5% and 0.3% for B0 to 7.2% and 1.3% for B100, respectively, at 25% load. Optimal injection timing varies with biodiesel ratio: 13–15° BTDC for B0 reducing to 10–12° BTDC for B100. These quantitative insights enable evidence-based optimization of marine diesel engines for improved environmental performance while maintaining operational efficiency. Full article

A wide experimental campaign was developed on an automotive turbocharged diesel engine, using two blends between diesel oil and waste cooking oil methyl esters (WCOME) and neat biodiesel. A conventional B7 diesel oil was considered as a reference fuel. The two blends, respectively, included 40 and 70% of WCOME, on a volumetric basis. The influence of biodiesel was analyzed by testing the engine in two part-load operating conditions, applying proper control strategies to the exhaust gas recirculation (EGR) circuit and rail pressure, to assess the interactions between the engine management and the tested fuels. The variable nozzle turbine (VNT) was controlled to obtain a constant level of intake pressure in the two experimental points. Referring to biodiesel effects at constant operating mode, higher WCOME content generally resulted in better efficiency and soot emission, while NO_X emission was negatively affected. EGR activation allowed for limited NO formation but with penalties in soot emission. Furthermore, interactions between the EGR circuit and turbocharger operations and control led to higher fuel consumption and lower efficiency. Finally, the increase in rail pressure corresponded to better soot emission and penalties in NO_X emission. Combining all these effects, the selection of EGR rate and rail pressure values higher than the standard levels resulted in better efficiency, NO_X, and soot emissions when comparing blends and neat biodiesel to conventional B7, granting advantages not only with regard to greenhouse gas emissions. Combustion parameters were also assessed, showing that combustion stability and combustion noise were not negatively affected by biodiesel use. Combustion duration was reduced when using WCOME and its blend, even if the center of combustion was slightly shifted along the expansion stroke. The main contribution of this investigation to the scientific and technical knowledge on biodiesel application to internal combustion engines is related to the development of tests on diesel–biodiesel blends with high WCOME content or neat WCOME, identifying their effects on NO_X emissions, the definition of integrated strategies of HP EGR system, fuel rail pressure, and VNT for the simultaneous reduction in NO_X and soot emissions, and the detailed assessment of the influence of biodiesel on a wide range of combustion parameters. Full article

Biodiesel and 2-methylfuran (MF) exhibit significant potential as alternative fuels due to advancements in their production techniques. Despite this potential, the low cetane number (CN) of biodiesel–MF (BMF) blends limits their practical use in diesel engines due to poor auto-ignition characteristics and extended ignition delays. This study addresses this issue by investigating the impact of the cetane improver 2-ethylhexyl nitrate (2-EHN) on the performance and emissions of a BMF30 blend. The blend consists of 70% biodiesel and 30% MF, with 2-EHN added at concentrations of 1% and 1.5% to enhance ignition properties. The experiments were conducted on a four-cylinder, four-stroke, direct-injection compression ignition (DICI) engine at a constant speed of 1800 rpm with brake mean effective pressures (BMEP) ranging from 0.13 to 1.13 MPa. The results showed that 2-EHN improved the CN of the BMF30 blend, leading to earlier combustion initiation and longer combustion duration. At low BMEP (0.13 MPa), 2-EHN increased the peak rate of heat release and in-cylinder pressure, whereas at higher BMEP (0.88 MPa), these parameters decreased. The key findings include a reduction in brake-specific fuel consumption (BSFC) by 5.49–7.33% and an increase in brake thermal efficiency (BTE) by 3.30–4.69%. Additionally, NOx emissions decreased by 9.4–17.48%, with the highest reduction observed at 1.5% 2-EHN. CO emissions were reduced by 45.1–85.5% and soot emissions also declined. Hydrocarbon (HC) emissions decreased by 14.56–24.90%. These findings demonstrate that adding 2-EHN to BMF30 blends enhances engine performance, reduces key emissions, and offers a promising alternative fuel for diesel engines. Full article

This paper presents the results of naturally aspirated compression ignition (CI) internal combustion engine (ICE) bench tests of fuels in the form of a blend of diesel oil with recycled oil (RF) in the form of tire pyrolysis oil (TPO) as an admixture with the content of pyrolytic oil with the blend being 10% m/m (D90+RF10). The results relate to reference conditions in which the engine is fed with pure diesel oil (D100). The experiment included the evaluation of engine performance and the determination of the content of selected substances in the exhaust gas for brake-set engine loads equal to 5 Nm, 10 Nm, 15 Nm, and 20 Nm. For each load, engine operating parameters and emissions of selected exhaust components were recorded at preset speeds in the range of 1400–2400 rpm for each engine load. The hourly fuel consumption and exhaust gas temperature were determined. The contents of CO₂, CO, and HC in the exhaust gas were measured. The consumption of D90+RF10 increased by 56%, and CO₂ emissions were 21.7% higher at low loads. The addition of sulfur-containing pyrolytic oil as an admixture to diesel oil resulted in SO_x emissions. The results show the suitability of pyrolytic oil and the possibility of using it as an admixture to fossil fuels. In order to meet SO_x emission levels in land-based installations and for vehicle propulsion, it is necessary to desulfurize fuel or desulfurize deSO_x exhaust gas systems. The CO and HC emission levels in the exhaust gases from the engine powered by the D90+RF10 fuel meet current requirements for motor vehicle exhaust composition. Full article

With conventional fuels dwindling and emissions rising, there is a necessity to develop and assess innovative substitute fuel for compression ignition (CI) engines. This study investigates the potential of magnesium oxide (MgO) nanoparticles as a sustainable additive to enhance the performance and reduce emissions of used cooking oil (UCO) biodiesel–diesel blends in CI engines. MgO nanoparticles were biosynthesized using Citrus aurantium peel extract, offering an environmentally friendly production method. A single-cylinder CI engine was used to test the performance of diesel fuel (B0), a 20% biodiesel blend (B20), and B20 blends with 30 ppm (B20M30) and 60 ppm (B20M60) MgO nanoparticles. Engine performance parameters (brake thermal efficiency (BTE), brake-specific fuel consumption (BSFC), and exhaust gas temperature (EGT)) and emission characteristics (CO, NO_x, unburnt hydrocarbons (HCs), and smoke opacity) were measured. The B20M60 blend showed a 2.38% reduction in BSFC and a 3.38% increase in BTE compared to B20, with significant reductions in unburnt HC, CO, and smoke opacity. However, NO_x emissions increased by 6.57%. The green synthesis method enhances sustainability, offering a promising pathway for cleaner and more efficient CI engine operation using UCO biodiesel, demonstrating the effectiveness of MgO nanoparticles. Full article