Search Results (510)

Soil microbial communities are crucial for ecosystem services, soil fertility, and the resilience of agroecosystems. This study investigated how long-term (31 years) agronomic practices—tillage, NPK fertilization, and cropping system—along with measured environmental variables influence the microbial biomass and its community composition in Chernozem soil under corn cultivation. The polyfactorial field experiment included three tillage treatments ((moldboard (MT), ripped (RT), strip (ST)), two fertilization regimes (NPK (N: 160; P: 26; K: 74 kg/ha), and unfertilized control) and two cropping systems (corn monoculture and corn–wheat biculture). The soil samples (0–30 cm) were collected in June and September 2023. Microbial biomass and community structure were quantified using phospholipid fatty acid (PLFA) analysis, which allowed the estimation of total microbial biomass and community composition (arbuscular mycorrhizal (AM) fungi, fungi, Gram-negative (GN) and Gram-positive (GP) bacteria, actinomycetes). Our results showed that microbial biomass increased from June to September, rising by 270% in unfertilized plots and by 135% in NPK-fertilized plots, due to higher soil moisture. Reduced tillage, especially ST, promoted significantly higher microbial biomass, with biomass reaching 290% and 182% of that in MT plots in June and September, respectively. MT had a higher ratio of bacteria-to-fungi compared to RT and ST, indicating a greater sensitivity of fungi to disturbance. NPK fertilization lowered soil pH by about one unit (to 4.1–4.8) and reduced microbial biomass—by 2% in June and 48% in September—compared to the control, with the particular suppression of AM fungi. The cropping system had a smaller overall effect on microbial biomass. Full article

This study aims to clarify the longitudinal flexural cracking characteristics in hogging moment regions and propose a practical calculation method for the cracking load and ultimate bearing capacity for a steel–GFRP strips–UHPC composite deck structure. The longitudinal flexural behavior of two steel–GFRP strips–UHPC composite beams in the hogging moment region is determined through a three-point loading test method. Their failure modes and mechanisms, crack propagation and distribution characteristics are analyzed considering the influence of the reinforcement ratio. The variation of the law of mid-span displacement, maximum crack width, strains and interface slip with load are discussed. Calculation methods for the cracking load and ultimate bearing capacity of steel–GFRP strips–UHPC composite beams are proposed. The results show that with the increase of the reinforcement ratio, the cracking load and ultimate bending capacity are improved by 11.1% and 6.0%, respectively. However, the development of cracks is inhibited, as the crack width, average crack spacing and strain of the reinforcement bars are reduced as the reinforcement ratio increases. The maximum crack width changes linearly with the load as it is less than 0.2 mm. The theoretical cracking load and ultimate bearing capacity of the composite beams considering the tensile contribution of UHPC achieve good agreement with the experimental values. Full article

Continuous SiC fiber-reinforced SiC matrix composites (SiC/SiC), as structural heat protection integrated materials, are often used in parts for large-area heat protection and sharp leading edges, and there are a variety of low-velocity impact events in their service. In this paper, a drop hammer impact test was conducted using narrow strip samples to simulate the low-velocity impact damage process of sharp-edged components. During the test, different impact energies and impact times were set to focus on investigating the low-velocity impact damage characteristics of 2.5D SiC/SiC composites. To further analyze the damage mechanism, computed tomography (CT) was used to observe the crack propagation paths and distribution states of the composites before and after impact, while scanning electron microscopy (SEM) was employed to characterize the differences in the micro-morphology of their fracture surfaces. The results show that the in-plane impact behavior of a 2.5D needled SiC/SiC composite strip samples differs from the conventional three-stage pattern. In addition to the three stages observed in the energy–time curve—namely in the quasi-linear elastic region, the severe load drop region, and the rebound stage after peak impact energy—a plateau stage appears when the impact energy is 1 J. During the impact process, interlayer load transfer is achieved through the connection of needled fibers, which continuously provide significant structural support, with obvious fiber pull-out and debonding phenomena. When the samples are subjected to two impacts, damage accumulation occurs inside the material. Under conditions with the same total energy, multiple impacts cause more severe damage to the material compared to a single impact. Full article

The use of short cylinders of recycled aggregate concrete (RAC) reinforced with basalt fiber-reinforced polymer (BFRP) circumferential strips and polyvinyl chloride (PVC) tubes has been proven effective in previous studies. However, BFRP circumferential strips are cumbersome to install and do not ensure the integrity of the BFRP strips. Therefore, this study investigates axial compression experiments on RAC short cylinders reinforced with BFRP spiral strips and PVC tubes. A combination of experimental studies, finite element simulations, and theoretical analyses revealed that the winding angle and spacing of BFRP strips significantly affect the load-bearing capacity and ductility of the restrained specimens. Additionally, an improved strength model was developed based on an existing model. When evaluated using both computational and experimental results, the equations generated in this study showed an average error of less than 10%. The findings indicate that the composite structure provides effective reinforcement and offers valuable reference information for practical applications. Full article

This paper assesses the complexity and diversity of vegetation in grassy strips with spontaneous plants between tree rows in three fruit orchards (plum, cherry, apple) in Dolj County, Romania, using structural and biodiversity indices. It addresses the lack of data on spontaneous vegetation in Romanian orchards, supporting improved plantation management and native biodiversity conservation. The study found that grassy strips supported high wild herbaceous diversity and a complex, heterogeneous ecological structure, with the apple orchard showing the highest biodiversity. Species diversity, evaluated through species richness, evenness, and diversity indices (Shannon, Simpson, Menhinick, Gleason, etc.), showed species richness ranging from 30 species in the cherry orchard to 40 in the apple orchard. Several species, including Capsella bursa-pastoris, Geranium pusillum, Poa pratensis, Veronica hederifolia, Lolium perenne, and Convolvulus arvensis, were present in 100% of samples, making them constant species from a phytosociological perspective. Their presence indicates relatively stable plant communities in each orchard. From a phytocoenological view, an ecological plant community is defined not only by species composition but also by constancy and co-occurrence in sampling units. Dominance remained low in all orchards, indicating no single plant dominated, while evenness showed a uniform distribution of species. Full article

This work presents a comprehensive evaluation of the heat-sealability of films developed from chañar brea gum (CBG), a biopolymer with potential for packaging applications. Heat sealability is a critical property in the packaging industry, as it directly determines the integrity and functionality of the final product. The films were prepared by the 10% casting method with the addition of glycerin, and heat sealing was performed at 140 °C using a heat sealer. Heat sealing was performed on 2 cm × 10 cm strips of chañar gum in the horizontal (CBG-H) and vertical (CBG-V) directions. This study employs a joint determination to explore the fundamental properties of the films, including proximate analysis, antioxidant capacity, FTIR, DSC, TGA-DTGA, XRD, mechanical testing, water vapor permeability, sorption, and biodegradability. By integrating the results of all these determinations, this study seeks to evaluate and explain the “intimate relationships”—i.e., the complex interconnections among the molecular structure, composition, thermal behavior, mechanical properties, and barrier properties of channier gum films—and how these fundamental properties dictate and control their heat sealability. The thermal stability of CBG is up to 200 °C, with a melting point of 152.48 °C. The interstrand spacing was very similar at 4.88 nm for CBG and 4.66 nm for CBG-H. The SEM images of the heat seal show rounded shapes on the surface, while in the cross section, it is homogeneous and almost without gaps. The WVP decreased from 1.7 to 0.37 for CBG and CBG-H, respectively. The Young’s modulus decreased from 132 MPa for CBG to 96.5 MPa for CBG-H. The heat sealability is 656 N/m, with a biodegradability of 4 days. This comprehensive approach is crucial for optimizing the sealing process and designing functional and efficient biodegradable packages. Full article

Prefabricated unidirectional carbon fiber reinforced polymer (CFRP) composite strips are extensively used as a means of infrastructure rehabilitation through adhesive bonding to the external surface of structural concrete elements. Most data to date are from laboratory tests ranging from a few months to 1–2 years providing an insufficient dataset for prediction of long-term durability. This investigation focuses on the assessment of the response of three different prefabricated CFRP systems exposed to water, seawater, and alkaline solutions for 5 years of immersion in deionized water conducted at three temperatures of 23, 37.8 and 60 °C, all well below the glass transition temperature levels. Overall response is characterized through tensile and short beam shear (SBS) testing at periodic intervals. It is noted that while the three systems are similar, with the dominant mechanisms of deterioration being related to matrix plasticization followed by fiber–matrix debonding with levels of matrix and interface deterioration being accelerated at elevated temperatures, their baseline characteristics and distributions are different emphasizing the need for greater standardization. While tensile modulus does not degrade appreciably over the 5-year period of exposure with final levels of deterioration being between 7.3 and 11.9%, both tensile strength and SBS strength degrade substantially with increasing levels based on temperature and time of immersion. Levels of tensile strength retention can be as low as 61.8–66.6% when immersed in deionized water at 60 °C, those for SBS strength can be 38.4–48.7% at the same immersion condition for the three FRP systems. Differences due to solution type are wider in the short-term and start approaching asymptotic levels within FRP systems at longer periods of exposure. The very high levels of deterioration in SBS strength indicate the breakdown of the materials at the fiber–matrix bond and interfacial levels. It is shown that the level of deterioration exceeds that presumed through design thresholds set by specific codes/standards and that new safety factors are warranted in addition to expanding the set of characteristics studied to include SBS or similar interface-level tests. Alkali solutions are also shown to have the highest deteriorative effects with deionized water having the least. Simple equations are developed to enable extrapolation of test data to predict long term durability and to develop design thresholds based on expectations of service life with an environmental factor of between 0.56 and 0.69 for a 50-year expected service life. Full article

Gel-polymer electrolytes offer a promising route toward safer and more stable sodium-ion batteries, but conventional polymer systems often suffer from low ionic conductivity and limited voltage stability. In this study, we developed composite GPEs by embedding methylammonium lead chloride (CH₃NH₃PbCl₃, MPCl) into a UV-crosslinked ethoxylated trimethylolpropane triacrylate (ETPTA) matrix, with sodium alginate (SA) as an ionic conduction enhancer. Three types of membranes—GPE-P, GPE-El, and GPE-Eh—were synthesized and systematically compared. Among them, the high-MPCl formulation (GPE-Eh) exhibited the best performance, achieving a high ionic conductivity of 2.14 × 10⁻³ S·cm⁻¹, a sodium-ion transference number of 0.66, and a wide electrochemical window of approximately 4.9 V vs. Na⁺/Na. In symmetric Na|GPE|Na cells, GPE-Eh enabled stable sodium plating/stripping for over 600 h with low polarization. In Na|GPE|NVP cells, it delivered a high capacity retention of ~79% after 500 cycles and recovered ~89% of its initial capacity after high-rate cycling. These findings demonstrate that the perovskite–polymer composite structure significantly improves ion transport, interfacial stability, and electrochemical durability, offering a viable path for the development of next-generation quasi-solid-state sodium-ion batteries. Full article

We investigate the impact of normal linear strips—both perpendicular and parallel to the direction of vortex motion—on the dynamics of fractional vortices in a two-band superconducting slab. In the absence of pinning, composite vortices dominate throughout the sample, while non-composite (dissociated) vortices appear only near the vortex entry edge, with energy dissipation primarily governed by the motion of composite structures. To modulate vortex behavior, we introduce linear regions of locally suppressed superconductivity, oriented either perpendicular or parallel to the vortex trajectory. A single perpendicular strip confines fractional vortices to the injection region, whereas two perpendicular strips stabilize composite vortices in the central domain and induce fractional vortex states near the boundaries. In contrast, parallel strips promote the dissociation of vortices across the entire sample, significantly altering the spatial configuration and dynamics of the vortex matter. Furthermore, the interband correlation coefficient serves as a direct indicator of the degree of spatial overlap between vortices in the two condensates. These findings highlight the critical role of pinning geometry in shaping vortex dynamics and energy dissipation, offering new strategies for controlling flux behavior in multiband superconductors for technological applications. Full article

This study investigates the effectiveness of strain-hardening cementitious composites (SHCC) reinforced with glass fiber (GF) mesh in enhancing the torsional behavior of reinforced concrete (RC) beams with circular openings. Eight full-scale RC beams were tested under pure torsion, including two control beams and six strengthened beams with varying configurations of horizontal, vertical, and combined SHCC-GF mesh retrofitting. The experimental program evaluated the influence of single- and double-layer GF mesh reinforcement on torsional capacity, crack propagation, stiffness, and energy absorption. The results demonstrated that the presence of an opening reduced the ultimate torsional capacity by 29%, elastic stiffness by 48%, and energy absorption by 64% compared to the solid control beam. Strengthening with horizontal SHCC strips restored 21–35% of the lost capacity, while vertical strips performed even better, achieving 44–61% improvement. The combined horizontal–vertical configuration with a double-layer GF mesh proved the most effective, increasing ultimate load by 91% compared to the unstrengthened beam with an opening. Finite element models (FEM) are developed using ABAQUS to simulate the performance of the tested beams. Full article

This study investigated the application of neural network techniques to predict the mechanical properties of low-carbon hot-rolled steel strips using industrial data. A feedforward neural network (FFNN) model was developed to predict the yield strength (YS), ultimate tensile strength (UTS), and elongation (%EL) based on the chemical composition and processing parameters. For the low-carbon hot-rolled steel strip (C: 0.02–0.06%, Mn: 0.17–0.38%), 435 datasets were utilized with 17 input parameters, including 15 composition elements, finish rolling temperature (FRT), and coil target temperature (CTT). The model was trained using 335 datasets and tested using 100 randomly selected datasets. The optimum network architecture consisted of two hidden layers with 34 neurons each, achieving a mean squared error of 0.014 after 200,000 iterations. The model predictions showed excellent agreement with the actual values, with mean percentage errors of 4.44%, 3.54%, and 4.84% for the YS, UTS, and %EL, respectively. The study further examined the influence of FRT and CTT on mechanical properties, demonstrating that FRT has more complex effects on mechanical properties than CTT. The model successfully predicted property variations with different processing parameters, thereby providing a valuable tool for alloy design and process optimization in steel manufacturing. Full article

The use of recycled aggregate concrete (RAC) in construction mitigates environmental pollution by repurposing demolition waste, but its lower compressive strength compared to natural aggregate concrete (NAC) limits broader application. Although carbon fiber reinforced polymer (CFRP) composites and polyvinyl chloride (PVC) tubes have individually been shown to improve concrete strength and ductility, existing studies focus on fully wrapped CFRP jackets on NAC columns and do not systematically explore CFRP–PVC hybrid confinement using strips on RAC. To address this research gap, this study investigates the axial compressive behavior of CFRP–PVC–RAC columns by varying CFRP strip width (from 25 to 75 mm), strip spacing (from 31 to 77.5 mm), and the number of CFRP layers (one to nine) over a central PVC tube. Axial compression tests reveal that specimens with a central CFRP strip width equal to or greater than 75 mm achieve peak loads up to 1331 kN and that, after rupture of the central strip, the remaining strips continue to carry load, producing a more gradual stress–strain decline and enhanced ductility compared to fully wrapped controls (peak load 1219 kN). These results show that CFRP–PVC composites enhance the axial compressive strength and ductility of RAC columns. The confinement mechanism increases the ultimate axial strain and redistributes transverse stresses, delaying brittle failure and improving deformation capacity. When two or more CFRP layers are applied, strip width and spacing affect axial stress by no more than three percent. Increasing layers from one to four raises axial strength by approximately 23 percent, whereas adding layers beyond four yields diminishing returns, with less than a six percent increase. Finally, a multilayer lateral confined pressure formula is derived and validated against thirty-two specimens, exhibiting errors no greater than three percent and accurately predicting effective confinement. These findings offer practical guidance for optimizing strip dimensions and layering in CFRP–PVC reinforcement of RAC columns, achieving material savings without compromising performance. Full article

Background/Objectives: To evaluate the concentrations of trace elements in tear fluid among athletes using particle-induced X-ray emission (PIXE), and to assess the associations with gender, sports intensity, and nutritional supplement intake. Methods: In this cohort study, 84 athletes engaged in high- or low-intensity sports completed a demographic and supplement-use questionnaire. Tear samples were collected using Schirmer strips and analyzed for elemental composition with PIXE, a high-sensitivity technique suited for small biological samples. Multivariate and nonparametric statistical analyses were used to compare groups. Results: There were 46 males and 38 females, aged 17–63 years (mean 30.21 years). Tear phosphorus, potassium, and sulfur concentrations were higher in women than men and higher in women participating in low-intensity compared to high-intensity sports. Tear concentrations of magnesium were higher in men participating in high-intensity sports compared to low-intensity sports. They were higher in men than women regardless of supplement intake. Iron concentrations were higher in men than women only when neither group was taking supplements. Smoking had a slight inverse relationship to iron values. Iron levels were particularly high in men participating in intense sports and low in smokers. Magnesium supplements were associated with raised magnesium levels in tears. Conclusions: This study demonstrates an association between trace element levels in human tears and gender, sports intensity, and food supplement intake. PIXE enables the evaluation of trace element concentration in tears, which may serve as potential biomarkers for the clinical assessment of athletes’ health. Full article

The Soil and Water Assessment Tool (SWAT) was utilized to analyze the spatiotemporal distribution patterns of composite non-point source pollution in the Yapu Port Basin, China, and to quantify the pollutant load contributions from various sources. Scenario-based simulations were designed to assess the effectiveness of different mitigation strategies, focusing on both agricultural and urban non-point source pollution control. The watershed was divided into 39 sub-watersheds and 106 hydrologic response units (HRUs). Model calibration and validation were conducted using the observed data on runoff, total phosphorus (TP), and total nitrogen (TN). The results demonstrate good model performance, with coefficients of determination (R²) ≥ 0.85 and Nash–Sutcliffe efficiencies (NSEs) ≥ 0.84, indicating its applicability to the study area. Temporally, pollutant loads exhibited a positive correlation with precipitation, with peak values observed during the annual flood season. Spatially, pollution intensity increased from upstream to downstream, with the western region of the watershed showing higher loss intensity. Pollution was predominantly concentrated in the downstream region. Based on the composite source analysis, a series of management measures were designed targeting both agricultural and urban non-point source pollution. Among individual measures, fertilizer reduction in agricultural fields and the establishment of vegetative buffer strips demonstrated the highest effectiveness. Combined management strategies significantly enhanced pollution control, with average TN and TP load reductions of 22.18% and 22.70%, respectively. The most effective scenario combined fertilizer reduction, improved urban stormwater utilization, vegetative buffer strips, and grassed swales in both farmland and orchards, resulting in TN and TP reductions of 67.2% and 56.2%, respectively. Full article

The sharp rise in the worldwide production of biodiesel has created an excess in the crude glycerol market, so it is essential to develop new added-value alternatives for crude glycerol. This paper describes a study on fermenting high concentrations of two types of medium-pure crude glycerol to solvents by Clostridium pasteurianum. The effect of media composition (iron, yeast extract, and vitamins) on solvents production was assessed by a full factorial design with pure glycerol. Granular activated carbon (GAC) adsorption was highly effective in removing impurities from crude glycerol. Following GAC pretreatment, fermentation of glycerol at initial concentration as high as 60 g L⁻¹ was possible, resulting in a butanol production of ~9 g L⁻¹. Based on these results, a batch fermentation with in situ gas stripping and pH controlled at ≥6.5 was shown to be the best alternative to enhance biomass growth, glycerol uptake, and solvent production. The combination of controlling pH in the early stages of fermentation with in situ butanol removal stabilised the metabolism of the strain and showed that the fermentation performance with crude glycerol is very similar to that of pure glycerol. With a notable uptake of glycerol (>83%), solvent production was >11 g L⁻¹ butanol (yield > 0.21 g g⁻¹_{glycerol consumed}) and >6 g L⁻¹ 1,3-propanediol (yield > 0.13 g g⁻¹_{glycerol consumed}). Setting the fermentation conditions to achieve a high uptake of high levels of glycerol with a similar product distribution is of great interest for the viability of the industrial processing of crude glycerol into chemicals via biological conversion. Full article