Search Results (1,386)

Titanium dioxide (TiO₂), a widely used semiconductor in photocatalysis owing to its adequate potential for water hydrolysis, chemical stability, low toxicity, and low cost. However, its efficiency is limited by fast charge-carrier recombination and poor visible light absorption. Coupling TiO₂ with a p-type semiconductor, such as nickel oxide (NiO), forming a p-n heterojunction, decreases the recombination of charge carriers and increases photocatalytic activity. In this work, the surface of TiO₂ modified with NiO nanoparticles (NPs) induced by radiolysis for photocatalytic hydrogen production was studied. The photocatalytic activity of NiO/TiO₂ was evaluated using methanol as a hole scavenger under UV–visible light. All modified samples presented superior photocatalytic activity compared to bare TiO₂. The dynamics of the charge carriers, a key electronic phenomenon in photocatalysis, was investigated by time-resolved microwave conductivity (TRMC). The results highlight the crucial role of Ni-based NPs modification in enhancing the separation of the charge carrier and activity under UV–visible irradiation. Furthermore, the results revealed that under visible irradiation, NiO-NPs inject electrons into the conduction band of titanium dioxide. Full article

Blood is a widely used sample for diagnosing diseases such as malaria and diabetes. While diagnostic techniques have advanced, sample preparation remains labor-intensive, requiring steps like mixing and centrifugation. Microfluidic technologies have automated parts of this process, including cell lysis, yet challenges persist. Electrical lysis offers a chemical-free, continuous approach, but lysing small cells like red blood cells requires high electric fields, which can damage electrodes and cause system failures. Here, we present a microfluidic device utilizing ion concentration polarization (ICP) for rapid blood cell lysis at 75 V. Fluorescence imaging confirmed the formation of an ion depletion region near the Nafion^® nanochannel membrane, where the electric field was concentrated across the entire microchannel width. This phenomenon enabled the efficient trapping and lysis of blood cells under these conditions. Continuous blood injection achieved a lysis time of 0.3 s with an efficiency exceeding 99.4%. Moreover, lysed cell contents accumulated near the Nafion membrane, forming a concentrated lysate. This approach eliminates the need for high-voltage circuits or chemical reagents, offering a simple yet effective method for blood cell lysis. The proposed device is expected to advance lab-on-a-chip and point-of-care diagnostics by enabling rapid and continuous sample processing. Full article

Capturing CO₂ emitted by coal chemical enterprises and injecting it into oil reservoirs not only effectively improves the recovery rate and development efficiency of tight oil reservoirs in the Ordos Basin but also addresses the carbon emission problem constraining the development of the region. Since initiating field experiments in 2012, the Ordos Basin has become a significant base for CCUS (Carbon capture, Utilization, and Storage) technology application and demonstration in China. However, over the years, projects have primarily focused on enhancing the recovery rate of CO₂ flooding, while issues such as potential reservoir damage and its extent have received insufficient attention. This oversight hinder the long-term development and promotion of CO₂ flooding technology in the region. Experimental results were comprehensively analyzed using techniques including nuclear magnetic resonance (NMR), X-ray diffraction (XRD), scanning electron microscopy (SEM), inductively coupled plasma (ICP), and ion chromography (IG). The findings indicate that under current reservoir temperature and pressure conditions, significant asphaltene deposition and calcium carbonate precipitation do not occur during CO₂ flooding. The reservoir’s characteristics-high feldspar content, low carbon mineral content, and low clay mineral content determine that the primary mechanism affecting physical properties under CO₂ flooding in the Chang 4 + 5 tight sandstone reservoir is not, as traditional understand, carbon mineral dissolution or primary clay mineral expansion and migration. Instead, feldspar corrosion and secondary particles migration are the fundamental reasons for the changes in reservoir properties. As permeability increases, micro pore blockage decreases, and the damaging effect of CO₂ flooding on reservoir permeability diminishes. Permeability and micro pore structure are therefore significant factors determining the damage degree of CO₂ flooding inflicts on tight reservoirs. In addition, temperature and pressure have a significant impact on the extent of reservoir damage caused by CO₂ flooding in the study region. At a given reservoir temperature, increasing CO₂ injection pressure can mitigate reservoir damage. It is recommended to avoid conducting CO₂ flooding projects in reservoirs with severe pressure attenuation, low permeability, and narrow pore throats as much as possible to prevent serious damage to the reservoir. At the same time, the production pressure difference should be reasonably controlled during the production process to reduce the risk and degree of calcium carbonate precipitation near oil production wells. Full article

This work deals with the catalytic steam reforming of raw syngas to increase the efficiency of coupling gasification with downstream processes (such as fuel cells and catalytic chemical syntheses) by producing high-temperature, ready-to-use syngas without cooling it for cleaning and conditioning. Such a combination is considered a key point for the future exploitation of syngas produced by steam gasification of biogenic solid fuel. The design and construction of an integrated gasification and gas conditioning system were proposed approximately 20 years ago; however, they still require further in-depth study for practical applications. A 3D model of the freeboard of a pilot-scale, fluidized bed gasification plant equipped with catalytic ceramic candles was used to investigate the optimal operating conditions for in situ syngas upgrading. The global kinetic parameters for methane and tar reforming reactions were determined experimentally. A fluidized bed gasification reactor (~5 kWth) equipped with a 45 cm long segment of a fully commercial filter candle in its freeboard was used for a series of tests at different temperatures. Using a computational fluid dynamics (CFD) description, the relevant parameters for apparent kinetic equations were obtained in the frame of a first-order reaction model to describe the steam reforming of key tar species. As a further step, a CFD model of the freeboard of a 100 kWth gasification plant, equipped with six catalytic ceramic candles, was developed in ANSYS FLUENT^®. The composition of the syngas input into the gasifier freeboard was obtained from experimental results based on the pilot-scale plant. Simulations showed tar catalytic conversions of 80% for toluene and 41% for naphthalene, still insufficient compared to the threshold limits required for operating solid oxide fuel cells (SOFCs). An overly low freeboard temperature level was identified as the bottleneck for enhancing gas catalytic conversions, so further simulations were performed by injecting an auxiliary stream of O₂/steam (50/50 wt.%) through a series of nozzles at different heights. The best simulation results were obtained when the O₂/steam stream was fed entirely at the bottom of the freeboard, achieving temperatures high enough to achieve a tar content below the safe operating conditions for SOFCs, with minimal loss of hydrogen content or LHV in the fuel gas. Full article

Polystyrene (PS), a thermoplastic polymer, is used in many applications due to its mechanical performance, good chemical inertness, and excellent processability. However, it is doped with different nanomaterials for reasons such as improving its electrical conductivity and mechanical properties. In this study, carbon nanotube (CNT)-added PS composites were produced with the aim of combining the properties of CNTs, such as their low weight and high tensile strength and Young’s modulus, with the versatility, processability, and mechanical properties of PS. In this study, multi-walled carbon nanotube (MWCNT)-reinforced polystyrene (PS) composites with different percentage ratios (0.1, 0.2, and 0.3 wt%) were prepared by a plastic injection molding method. The mechanical, microstructural, and thermal properties of the fabricated PS/MWCNT composites were characterized by Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FTIR) Spectroscopy, Atomic Force Microscopy (AFM) and Thermogravimetric Analysis (TGA) techniques. AFM analyses were carried out to investigate the surface properties of MWCNT-reinforced composite materials by evaluating the root mean square (RMS) values. These analyses show that the RMS value for MWCNT-reinforced composite materials decreases as the weight percentage of MWCNTs increases. The TGA results show that there is no change in the degradation temperature of the 0.1%- and 0.2%-doped MWCNT composites compared to pure polystyrene, but the degradation of the 0.3%-doped MWCNT composite is almost complete at a temperature of 539 °C. Among the PS/MWCNT composites, the 0.3%-doped MWCNT composite exhibits more thermal stability than pure PS and other composites. Similarly, the values of the percentage elongation and tensile strength of 0.3% MWCNT-doped composites was obtained as 1.91% and 12.174% mm², respectively. These values are higher than the values of 0.1% and 0.2% MWCNT-doped composite materials. In conclusion, the mechanical and thermal properties of MWCNT-reinforced PS polymers provide promising results for researchers working in this field. Full article

Introduction: Sepsis-associated encephalopathy (SAE) is an acute brain dysfunction secondary to systemic infection, occurring without direct central nervous system involvement. Despite its clinical relevance, reliable biomarkers for diagnosing SAE and assessing its severity remain limited. This study aimed to evaluate the feasibility of amide proton transfer-weighted (APTw) chemical exchange saturation transfer (CEST) MRI as a non-invasive molecular imaging technique for detecting metabolic alterations related to neuroinflammation in SAE. Using a lipopolysaccharide (LPS)-induced rat model, we focused on hippocampal changes associated with neuronal inflammation. Materials and Methods: Twenty-one Sprague–Dawley rats (8 weeks old, male) were divided into three groups: control (CTRL, n = 7), LPS-induced sepsis at 5 mg/kg (LPS05, n = 7), and 10 mg/kg (LPS10, n = 7). Sepsis was induced via a single intraperitoneal injection of LPS. APTw imaging was performed using a 7 T preclinical MRI system, and signal quantification in the hippocampus was conducted using the magnetization transfer ratio asymmetry analysis. Results and Discussion: APTw imaging at 7 T demonstrated significantly elevated hippocampal APTw signals in SAE model rats (LPS05 and LPS10) compared to the control (CTRL) group: CTRL (−1.940 ± 0.207%) vs. LPS05 (−0.472 ± 0.485%) (p < 0.001) and CTRL vs. LPS10 (−0.491 ± 0.279%) (p < 0.001). However, no statistically significant difference was observed between the LPS05 and LPS10 groups (p = 0.994). These results suggest that APTw imaging can effectively detect neuroinflammation-related metabolic alterations in the hippocampus. Conclusion: Our findings support the feasibility of APTw CEST imaging as a non-invasive molecular MRI technique for SAE, with potential applications in diagnosis, disease monitoring, and therapeutic evaluation. Full article

Mesoporous silicon dioxide films have been shown to be well suited as adhesion-promoting interlayers for generating high-strength polymer–metal interfaces. These films can be fabricated via microwave plasma-enhanced chemical vapor deposition using the precursor hexamethyldisiloxane and oxygen as working gas. The resulting mesoporous structures enable polymer infiltration during overmolding, which leads to a nanoscale form-locking mechanism after solidification. This mechanism allows for efficient stress transfer across the interface and makes the resulting adhesion highly dependent on the morphology of the deposited film. To gain a deeper understanding of the underlying deposition mechanisms and improve process stability, this work investigates the growth behavior of mesoporous silica films using a multiple regression analysis approach. The seven process parameters coating time, distance, chamber pressure, substrate temperature, flow rate, plasma pulse duration, and pause-to-pulse ratio were systematically varied within a Design of Experiments framework. The resulting films were characterized by their free surface area, mean agglomerate diameter, and film thickness using digital image analysis, white light interferometry, and atomic force microscopy. The deposited films exhibit a wide range of morphological appearances, ranging from quasi-dense to dust-like structures. As part of this research, the free surface area varied from 15 to 55 percent, the mean agglomerate diameter from 17 to 126 nm, and the film thickness from 35 to 1600 nm. The derived growth model describes the deposition process with high statistical accuracy. Furthermore, all coatings were overmolded via injection molding and subjected to mechanical testing, allowing a direct correlation between film morphology and their performance as adhesion-promoting interlayers. Full article

Unconventional hydrocarbon reservoirs with low matrix permeability (<0.3 mD), high temperatures, and sour conditions present significant challenges for stimulation and production enhancement. This study examines field trials for a large oil and gas operator in the UAE, focusing on tight carbonate deposits with reservoir temperatures above 93 °C and high sour gas content. A novel multi-stage chemical stimulation workflow was created, beginning with a pre-flush phase that alters rock wettability and reduces interfacial tension at the micro-scale. This was followed by a second phase that increased near-wellbore permeability and ensured proper acid placement. The treatment’s core used a thermally stable, corrosion-resistant retarded acid system designed to slow reaction rates, allow deeper acid penetration, and build prolonged conductive wormholes. Simulations revealed considerable acid penetration of the formation beyond the near-wellbore zone. The post-treatment field data showed a tenfold improvement in injectivity, which corresponded closely to the acid penetration profiles predicted by modeling. Furthermore, oil production demonstrated sustained, high oil production of 515 bpd on average for several months after the treatment, in contrast to the previously unstable and low-rate production. Finally, the findings support a reproducible and technologically advanced stimulation technique for boosting recovery in ultra-tight carbonate reservoirs using the acid retardation effect where traditional stimulation fails. Full article

Fruit rot seriously damages pomelo production. Given concerns regarding the safety of chemical agents, biological alternatives are becoming more preferable. Therefore, the experiment aimed to (i) identify the pathogens causing pomelo fruit rot disease and (ii) select Trichoderma spp. strains controlling the determined pathogens in Ben Tre, Vietnam. Three pathogenic fungal strains isolated from diseased pomelo fruits were selected. The three pathogenic fungal strains were randomly injected into 9 healthy pomelo fruits. The strain PCP-B02-A2 led to a completely rotten fruit on day 17 after infection, while strains PCP-B02-B2 and PCP-B03-A1 had infected spots whose lengths were 17.5 and 28.1 mm, became larger, and eventually led to the whole fruit rot. The pathogens were identified by the internal transcribed spacer (ITS) technique as Colletotrichum gloeosporioides PCP-B02-A2, Pseudopestalotiopsis camelliae sinensis PCP-B03-A1, and P. chinensis PCP-B02-B2. Twenty-five Trichoderma spp. strains were isolated. The ITS technique identified four strains, including Trichoderma asperellum TP-B01, T. harzianum TP-B08, T. harzianum TP-B09, and T. asperellum TP-C25. The PCP-B02-A2 strain had antagonism at 66.7–68.7%, while those of PCP-B02-B2 and PCP-B03-A1 were 64.2–71.1% and 55.7–57.4%, respectively. Full article

Magnetic field (MF) priming provides a chemical-free alternative to conventional methods; however, static exposure approaches are often limited by spatial heterogeneity in field–seed interaction caused by fixed seed positioning, undermining both treatment uniformity and reproducibility. To address this, the present study investigated the effects of dynamic MF exposure on the germination and early growth of Khao Dawk Mali 105 (KDML 105) rice seeds. A novel MF testing apparatus was developed using a 150 mT permanent magnet and a vortex-based air injection system designed to continuously rotate and redistribute seeds, ensuring uniform exposure. Seeds were treated for 0, 5, 10, 15, and 20 min to evaluate effects on vigor, germination, and seedling growth. The results showed that 5 and 10 min exposures significantly enhanced seed vigor (93.00% and 94.67%, respectively) compared to the control (83.33%), with 10 min yielding the highest improvement (p < 0.05, DMRT). Shoot and root growth also increased by 14.21% and 99.59%, respectively. These findings suggest that moderate-duration dynamic MF exposure is an efficient, eco-friendly priming technique for improving seed vigor and early growth. Future research should explore long-term agronomic impacts, economic feasibility, and varietal responses. The apparatus’s scalable design supports integration into industrial seed processing lines, advancing sustainable rice production. Full article

Miraruira is a medicinal plant-based product (MPBP) that is widely used in the state of Amazonas for the treatment of diabetes, though its botanical identity remains unclear, which raises concerns about authenticity and therapeutic consistency. One solution to this problem is the use of mass spectrometry-based approaches, which have emerged as powerful tools for verifying botanical origin based on chemical composition. Thus, to confirm the botanical authenticity of miraruira, direct-injection mass spectrometry (DI-MS) and chemometric analyses (PCA and HCA) were conducted on methanol fractions of Salacia impressifolia and Connarus ruber, both suspected sources of miraruira, as well as commercial samples obtained in street markets in Manaus, Brazil. Additionally, the hexane extracts of C. ruber and the commercial samples were screened for benzoquinones using DI-MS, as these compounds are recurrent in the genus Connarus. The DI-MS and PCA analyses revealed distinct chemical profiles for each species, and identified mangiferin and epicatechin as chemical markers for S. impressifolia and C. ruber, respectively. Furthermore, PCA demonstrated that all the commercial samples exhibited chemical profiles closely aligned with C. ruber. However, the HCA indicated variability among these samples, suggesting C. ruber or related Connarus species are the primary sources of miraruira. Moreover, embelin, rapanone, and suberonone were identified as the main compounds in the hexane extracts of C. ruber and the commercial products. This study successfully confirmed the botanical authenticity of miraruira, identified key bioactive compounds related to its traditional use in the treatment of diabetes symptoms, and demonstrated the effectiveness of DI-MS as a valuable tool for addressing authenticity issues in MPBPs. Full article

Underground production and injection operations result in mechanical compaction and mineral chemical reactions that alter porosity and permeability. These changes impact the flow and, eventually, the long-term sustainability of reservoirs utilized for CO₂ sequestration and geothermal energy. Even though mechanical and chemical deformations in rocks take place at the pore scale, it is important to investigate their impact at the continuum scale. Rock deformation can be examined using intergranular pressure solution (IPS) models, primarily for uniaxial compaction. Because the reaction rate parameters are estimated using empirical methods and the assumption of constant mineral saturation indices, these models frequently overestimate the rates of compaction and strain by several orders of magnitude. This study presents a new THMC algorithm by combining thermo-mechanical computation with a fractal approach and hydrochemical computations using PHREEQC to evaluate the pressure solution. Thermal stress and strain under axisymmetric conditions are calculated analytically by combining a derived hollow circle mechanical structure with a thermal resistance model. Based on the pore scale, porosity and its impact on the overall excessive stress and strain rate in a domain are estimated by applying the fractal scaling law. Relevant datasets from CO₂ core flooding experiments are used to validate the proposed approach. The comparison is consistent with experimental findings, and the novel analytical method allows for faster inspection compared to numerical simulations. Full article

A varied family of polyphenolic chemicals, flavonoids, are becoming more and more important in bone tissue engineering because of their osteogenic, anti-inflammatory, and antioxidant effects. Recent developments incorporating flavonoids into different biomaterial platforms to improve bone regeneration are emphasized in this study. Osteocalcin (OCN) expression was 2.1-fold greater in scaffolds loaded with flavonoids—such as those made of polycaprolactone (PCL)—greatly increasing human mesenchymal stem cell (hMSC) proliferation and mineralization. Comparably, a threefold increase in calcium deposition indicates increased mineralization when hydroxyapatite (HA) was functionalized with flavonoids such as quercetin. These HA scaffolds with flavonoids also showed a 45% decrease in osteoclast activity, therefore promoting balanced bone remodeling. Concurrent with flavonoids like EGCG and quercetin, chitosan-based scaffolds encouraged osteogenic differentiation with increases in osteogenic markers like osteopontin (OPN) and alkaline phosphatase (ALP) expression by up to 82%. These scaffolds also showed 82% bone defect repair after six weeks in vivo, suggesting their promise in rapid bone regeneration. With an increase of up to 32% in the bone volume-to-total volume ratio (BV/TV) and 28% greater bone–implant contact (BIC), flavonoid coatings on titanium implants enhanced osteointegration in implantology. Displaying successful osteogenesis and immunomodulation, the addition of flavonoids into metal–organic frameworks (MOFs) and injectable hydrogels demonstrated a 72% increase in new bone formation in vivo. Though further research is required to confirm long-term clinical effectiveness, these findings show the great promise of flavonoid-functionalized biomaterials in bone regeneration. Full article

This study investigates the industrial potential of red gypsum (RG), a major by-product of titanium dioxide (TiO₂) production, for the development of thermoplastic polypropylene (PP)-based composites via melt extrusion, targeting agricultural applications. Prior to compounding, RG was thermally treated at approximately 200 °C to remove residual moisture and chemically bound water, resulting in its anhydrous form (CaSO₄). PP/RG composites were then formulated with RG loadings up to 20 wt.%, employing stearic acid (SA) as a compatibilizer. The resulting materials were thoroughly characterized and successfully processed through industrial-scale injection molding up to 250 °C. Morphological and FTIR analyses confirmed the role of SA in enhancing both filler dispersion and interfacial adhesion between RG and the PP matrix. SEM images revealed finer and more uniformly distributed RG particles, resulting in a reduced loss of ductility and elongation at break typically associated with filler addition. Specifically, the Young’s Modulus increased from 1.62 GPa (neat PP) up to 3.21 GPa with 20 wt.% RG and 0.6 wt.% SA. The addition of 0.6 wt.% SA also helped limit the reduction in stress at break from 46.68 MPa (neat PP) to 34.05 MPa and similarly mitigated the decrease in Charpy impact energy, which declined slightly from 2.66 kJ/m² (neat PP) to 2.24 kJ/m² for composites containing 20 wt.% RG. Preliminary phytotoxicity was assessed using germination tests on Lepidium sativum L. seeds. Eluates from both untreated and SA-treated RG powders resulted in germination indices below 80%, indicating phytotoxicity likely due to high sulfate ion concentrations. In contrast, eluates from composite pellets exhibited germination indices equal to or exceeding 100%, demonstrating the absence of phytotoxic effects. These results highlight the suitability of the developed composites for applications in floriculture and horticulture. The optimized composite pellets were successfully processed via injection molding to manufacture plant pots, which exhibited a dark brown coloration, confirming the effective pigmenting function of RG. These results demonstrate the potential of red gypsum to serve both as a functional filler and pigment in PP composites, providing a sustainable alternative to iron oxide pigments and promoting the valorization of industrial waste through resource recovery. Full article

The blast furnace (BF) and basic oxygen route account for approximately 70% of the global steel production and create 1.8 tons of CO₂ per ton of steel, produced primarily due to the use of coke and pulverized coal (PC) at the BF. With global pressure to reduce CO₂ emissions, optimization of BF operation is crucial, which is possible through optimizing fuel consumption, and improving process stability. Understanding the complex combustion and flow dynamics in the raceway region is essential for enhancing reducing agent utilization. Modeling plays a key role in predicting these behaviors and providing insights into the process; however, validation of these models is crucial for their reliability but difficult in the complex and hostile BF raceway region. In this study, a validated raceway model developed at Swerim was used to evaluate four different cases, namely R1 (Reference), R2 (Low oxygen to blast), R3 (High blast moisture), and R4 (High PC) using an injection coal from SSAB Oxelösund. During actual experiments, the temperature distribution in the raceway was measured using a thermovision camera (TVC) to validate the CFD simulation results. The combined use aims to cross-validate the results simultaneously to establish a reliable framework for future parametric studies of raceway behavior under varying operational conditions using CFD simulations The results indicated that it is possible to measure the temperature within the raceway region using TVC at depths indicated to be 0.5–0.7 m, when not obscured by the coal plume, or <0.5 m, when obscured. TVC measurements are clearly quantitatively affected when obscured, indicated by considerably lower temperatures in the order of 200 °C between similar process conditions. A decrease of O₂ injection results in an extended raceway region as the conditions become less chemically favorable for combustion due to a lower reactant content offsetting the ignition point and reducing the reaction rate in the raceway. An increased moisture content in the blast results in a reduced size of the race-way region as energy is consumed as latent energy and cracks water. An increase in PC rate results in a larger/wider raceway region, as more PC is devolatilized and combusted early on, resulting in larger gas volumes expanding the raceway region outwards, perpendicular to the injection. Full article