Search Results (298)

The development of gas sensors with high sensitivity and low operating temperatures is essential for practical applications in environmental monitoring and industrial safety. SnO₂-based gas sensors, despite their widespread use, often suffer from high working temperatures and limited sensitivity to H₂ gas, which presents significant challenges for their performance and application. This study addresses these issues by introducing a novel SnO₂-based sensor featuring a three-dimensional (3D) nanostructure, designed to enhance sensitivity and allow for room-temperature operation. This work lies in the use of a 3D anodic aluminum oxide (AAO) template to deposit SnO₂ nanoparticles through ultrasonic spray pyrolysis, followed by modification with platinum (Pt) nanoparticles to further enhance the sensor’s response. The as-prepared sensors were extensively characterized, and their H₂ sensing performance was evaluated. The results show that the 3D nanostructure provides a uniform and dense distribution of SnO₂ nanoparticles, which significantly improves the sensor’s sensitivity and repeatability, especially in H₂ detection at room temperature. This work demonstrates the potential of utilizing 3D nanostructures to overcome the traditional limitations of SnO₂-based sensors. Full article

This study reports the synthesis and evaluation of iron molybdate (Fe₂(MoO₄)₃) and iron tungstate (FeWO₄) as photocatalysts for the degradation of a real industrial effluent from aluminum anodizing processes under visible light irradiation. The oxides were synthesized via a co-precipitation method in an aqueous medium, followed by microwave-assisted hydrothermal treatment. Structural and morphological characterizations were performed using X-ray diffraction, field-emission scanning electron microscopy, Raman spectroscopy, ultraviolet–visible (UV–vis), and photoluminescence (PL) spectroscopies. The effluent was characterized by means of ionic chromatography, total organic carbon (TOC) analysis, physicochemical parameters (pH and conductivity), and UV–vis spectroscopy. Both materials exhibited well-crystallized structures with distinct morphologies: Fe₂(MoO₄)₃ presented well-defined exposed (001) and (110) surfaces, while FeWO₄ showed a highly porous, fluffy texture with irregularly shaped particles. In addition to morphology, both materials exhibited narrow bandgaps—2.11 eV for Fe₂(MoO₄)₃ and 2.03 eV for FeWO₄. PL analysis revealed deep defects in Fe₂(MoO₄)₃ and shallow defects in FeWO₄, which can influence the generation and lifetime of reactive oxygen species. These combined structural, electronic, and morphological features significantly affected their photocatalytic performance. TOC measurements revealed degradation efficiencies of 32.2% for Fe₂(MoO₄)₃ and 45.3% for FeWO₄ after 120 min of irradiation. The results highlight the critical role of morphology, optical properties, and defect structures in governing photocatalytic activity and reinforce the potential of these simple iron-based oxides for real wastewater treatment applications. Full article

Synthetic nanopores were recently demonstrated with memristive and nonlinear voltage-current behaviors, akin to ion channels in a cell membrane. Such ionic devices are considered a promising candidate for the development of brain-inspired neuromorphic computing techniques. In this work, we show the composite behavior of nanopore-array large memristors, formed with different membrane materials, pore sizes, electrolytes, and device arrangements. Anodic aluminum oxide (AAO) membranes with 5 nm and 20 nm diameter pores and track-etched polycarbonate (PCTE) membranes with 10 nm diameter pores are tested and shown to demonstrate memristive and nonlinear behaviors with approximately 10⁷–10¹⁰ pores in parallel when electrolyte concentration across the membranes is asymmetric. Ion diffusion through the large number of channels induces time-dependent electrolyte asymmetry that drives the system through different memristive states. The behaviors of series composite memristors with different configurations are also presented. In addition to helping understand fluidic devices and circuits for neuromorphic computing, the results also shed light on the development of field-assisted ion-selection-membrane filtration techniques as well as the investigations of large neurons and giant synapses. Further work is needed to de-embed parasitic components of the measurement setup to obtain intrinsic large memristor properties. Full article

We developed a novel and portable magnetic nanochannel electrochemical sensor for the sensitive detection of cadmium ions (Cd²⁺), which pose serious risks to food safety and human health. The sensor was fabricated by co-modifying an anodic aluminum oxide (AAO) nanochannel membrane with a composite of glutathione (GSH) and ferric oxide nanoparticles (Fe₃O₄), denoted as GSH@Fe₃O₄. This modified membrane was then integrated with a screen-printed carbon electrode (SPCE) to construct the GSH@Fe₃O₄/GSH@AAO/SPCE sensing platform. The performance of the sensor was evaluated using differential pulse voltammetry (DPV), which demonstrated a strong linear correlation between the peak current response and the concentration of Cd²⁺ in the range of 5–120 μg/L. The calibration equation was I_DPV(μA) = −0.31 + 0.98·C_{Cd²⁺(μg/L)}, with an excellent correlation coefficient (R² = 0.999, n = 3). The calculated limit of detection (LOD) was as low as 0.1 μg/L, indicating the high sensitivity of the system. These results confirm the successful construction of the GSH@Fe₃O₄/GSH@AAO/SPCE portable nanochannel sensor. This innovative sensing platform provides a rapid, sensitive, and user-friendly approach for the on-site monitoring of heavy metal contamination in agricultural products, especially grains. Full article

This work aims to clarify whether the individual advantages of the two commonly used silicate- and aluminate-based electrolytes for the plasma electrolytic oxidation (PEO) of steel can be combined in a two-step process. The first PEO step was carried out in an aluminate–phosphate electrolyte with pulsed voltage and anodic amplitudes between 150 V and 200 V. The second PEO step was carried out at an increased anodic voltage amplitude of 400 V in a silicate–phosphate electrolyte. As a reference, PEO was conducted in a single step in the same silicate–phosphate electrolyte at an increased anodic voltage amplitude of up to 400 V. The microstructural layer analysis was carried out using SEM and EDX analyses, Raman spectroscopy and XRD analysis. Heterogeneous layers containing iron oxide and iron phosphate form in the silicate–phosphate electrolyte at anodic voltage amplitudes up to 300 V by electrochemical reactions. Further increasing the anodic voltage amplitude up to 400 V results in heterogeneous layers, too. PEO in the aluminate–phosphate electrolyte at 150 V causes the formation of thin, amorphous layers mainly consisting of aluminum and iron oxides. At 200 V amplitude, a PEO layer with pronounced open porosity is formed, which primarily consists of the crystalline phases corundum and hercynite. During subsequent PEO in the silicate–phosphate electrolyte, the previously formed layers were replaced by a macroscopically homogeneous layer that is mostly nanocrystalline and may contain amorphous iron(-aluminum) phosphates and oxides as well as silicon oxide. It can be concluded that the two-step PEO process is suitable for the production of more homogeneous PEO layers. Full article

Plasma electrolytic oxidation (PEO) is an advanced electrochemical surface treatment technology. It can effectively improve the corrosion resistance of magnesium and its alloys. This paper aims to form protective PEO coatings on an AZ31 substrate with different electrolytes, while monitoring the micro-discharge evolution by noise intensity and morphology analysis. By setting the PEO parameters and monitoring process characteristics, such as current density, spark appearance, and noise intensity, it was deduced that the PEO process consists of the following three stages: anodic oxidation, spark discharge, and micro-arc discharge. The PEO oxide coating formed on the AZ31 alloy exhibits various irregular volcano-like structures. Oxygen species are uniformly distributed along the coating cross-section. Phosphorus species tend to be enriched inwards to the coating/magnesium substrate interface, while aluminum piles up towards the surface region. Surface roughness of the PEO coating formed in the silicate-based electrolyte was the lowest in an arithmetic average height (Sa) of 0.76 μm. Electrochemical analysis indicated that the corrosion current density of the PEO coating decreased by about two orders of magnitude compared to that of untreated blank AZ31 substrate, while, at the same time, the open-circuit potential shifted significantly to the positive direction. The corrosion current density of the 10 min/400 V coating was 1.415 × 10⁻⁶ A/cm², approximately 17% lower than that of the 2 min/400 V coating (1.738 × 10⁻⁶ A/cm²). For a fixed 10 min treatment, the longer the PEO duration time, the lower the corrosion current density. Finally, the tested potentiodynamic polarization curve reveals the impact of different types of PEO electrolytes and different durations of PEO treatment on the corrosion resistance of the oxide coating surface. Full article

A superhydrophobic surface with hierarchical micro/nano-array structures was successfully fabricated on 6061 aluminum alloy through a combination of femtosecond laser etching and anodic oxidation. Femtosecond laser etching formed a regularly arranged microscale “pit-protrusion” array on the aluminum alloy surface. After modification with a fluorosilane ethanol solution, the surface exhibited superhydrophobicity with a contact angle of 154°. Subsequently, the anodic oxidation process formed an anodic oxide film dominated by an array of aluminum oxide (Al₂O₃) nanopores at the submicron scale. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses revealed that the nanopore structures uniformly and continuously covered the laser-ablated layer. This hierarchical structure significantly increased the surface water contact angle to 162°. Wettability analysis showed that the prepared composite coating formed an air layer accounting for 91% of the surface area. Compared with the sample only treated by femtosecond laser etching, the presence of the Al₂O₃ nanopore structure significantly enhanced the mechanical durability, superhydrophobic durability, and corrosion resistance of the superhydrophobic surface. The proposed multi-step fabrication strategy offers an innovative method for creating multifunctional, durable superhydrophobic coatings and has important implications for their large-scale industrial use. Full article

This study focuses on the design and optimization of a monopolar electrode configuration for the hybrid electrochemical treatment of real washing machine wastewater. A combined electrocoagulation (EC) and electro-oxidation (EO) system was optimized to maximize pollutant removal efficiency while minimizing energy consumption. The monopolar setup employed mixed metal oxide (MMO) and aluminum anodes, along with a stainless steel cathode, operating under controlled conditions with sodium chloride as the supporting electrolyte. An applied current density of 15 mA cm⁻² achieved 90% chemical oxygen demand (COD) removal, 98% surfactant degradation, complete turbidity reduction within 120 min, and pH stabilization near 8. Additionally, electrochemical disinfection achieved <2 MPN/100 mL, with no detectable phenols and the presence of organic anions such as oxalate and acetate. These results demonstrate the effectiveness of an optimized monopolar EC–EO system as a cost-efficient and sustainable strategy for wastewater treatment and potential water reuse. Further studies should focus on refining energy consumption and monitoring reaction by-products to enhance large-scale applicability. Full article

The low hardness and insufficient wear resistance of aluminum and its alloys restrict their broader application in various fields. The application of surface protective coatings can effectively enhance the hardness and wear resistance of aluminum and its alloys. This article provides a comprehensive review of the recent research progress of wear-resistant coatings fabricated on aluminum and its alloys. The relevant achievements in the recent research works of preparing wear-resistant coatings by one-step methods (such as anodic oxidation, micro-arc oxidation, cold spraying, plasma spraying, and electrodeposition) and two-step methods (anodic oxidation and physical vapor deposition, micro-arc oxidation and sealing, magnetron sputtering, and plasma nitriding) are mainly introduced. The working principles of each coating preparation method, along with their impacts on the microstructure and tribological performance of the coatings, were systematically examined. Additionally, a comparative analysis was conducted to evaluate the advantages and disadvantages of each coating preparation method. Full article

The projected global energy demand for 2050 drives the imperative search for alternative and environmentally friendly energy sources. An emerging and promising alternative is microbial fuel cells assisted with microalgae. This research evaluated the potential of Chlorella sp. biomass in electricity production using microbial fuel cells (MFCs) with a single chamber and activated carbon and zinc electrodes at the laboratory scale over 20 days of operation. Maximum values of voltage (1271 ± 2.52 mV), current (4.77 ± 0.02 mA), power density (247.514 mW/cm²), current density (0.551 mA/cm²), and internal resistance (200.83 ± 0.327 Ω) were obtained. The biomass-maintained pH values of 7.32 ± 0.03–7.74 ± 0.02 and peaks of electrical conductivity of 2450 ± 17.1 µS/cm and oxidation-reduction potential of 952 ± 20 mV were reached. Meanwhile, cell density and absorbance increased to average values of 2.2933 × 10⁷ ± 1.15 × 10⁶ cells/mL and 3.471 ± 0.195 absorbance units (AU), respectively. Scanning electron microscopy micrographs allowed the observation of filamentous structures of the formed biofilm attached to carbon particles, and energy-dispersive X-ray spectroscopy spectra of the anodes determined the predominance of oxygen, carbon, silicon, aluminum, and iron. Finally, this research demonstrates the great potential of Chlorella sp. biomass for sustainable bioelectricity generation in MFCs. Full article

We explored anodic aluminum oxide (AAO) stealth materials combining low infrared emissivity and visible structural coloration through multi-parameter modulation. Using DC ion gold sputtering and UHV magnetron chromium sputtering, we successfully prepared an AAO stealth material with high-saturation visible structural coloration and low infrared emissivity (ε < 0.17). Quantitative evaluation based on the CIE Lab color difference model indicated that the gold-coated samples had high matching accuracy with PANTONE standard colors ($\mathsf{\Delta }{E}_{ab}^{*}$ < 1.6). The chromium-coated samples had slightly lower matching accuracy ($\mathsf{\Delta }{E}_{ab}^{*}$ < 3.0), but still displayed rich coloration, with color difference within human-perceptible tolerance limits. Full article

With the evolution of micro/nanotechnology, anodic aluminum oxide (AAO) has received attention for sensor applications due to its regular and high-aspect-ratio nanopore structure with an excellent sensing performance, especially for electrical and optical sensors. Here, we propose the application of these capacitance and porous properties in a facile nanoporous AAO liquid sensor and study an efficient and economical method for preparing AAO substrates for liquid-phase substance sensing. By applying hybrid pulse anodization (HPA), a growth rate of approximately 5.9 μm/h was achieved in AAO fabrication. Compared to traditional low-temperature (0–10 °C) and two-step anodization with a growth rate of 1–3 μm/h, this process is significantly improved. The effect of pore widening on the performance of electrical sensors is also investigated and discussed. After pore widening, the capacitance values of AAO for air as a reference and various liquids, namely deionized water, alcohol, and acetone, are measured as 3.8 nF, 295.3 nF, 243.5 nF, and 210.1 nF, respectively. These results align with the trend in the dielectric constants and demonstrate the ability to clearly distinguish between different substances. The mechanism of AAO capacitive liquid-phase sensors can mainly be explained from two perspectives. First, since an AAO capacitive sensor is a parallel capacitor structure, the dielectric constant of the substance directly influences the capacitance value. In addition, pore widening increases the proportion of liquid filling the structure, enabling the sensor to clearly differentiate between substances. The other is the affinity between the substance and the AAO sensor, which can be determined using a contact angle test. The contact angles are measured as values of 93.2° and 67.7° before and after pore widening, respectively. The better the substance can fully fill the pores, the higher the capacitance value it yields. Full article

Aluminum alloy AA6082 (Al-Si-Mg) is a lightweight alloy that requires thick barrier coatings to be protected from localized corrosion. Plasma Electrolytic Oxidation (PEO) coating is a common anodic surface treatment used for growing protective oxides; the main process variables of PEO are the composition of the electrolytic solution and the electrical input. This work focuses on the optimization of the electrical input by comparing different coatings produced by potentiostatic PEO at the effective potential of 350 V, applied by different combinations of voltage ramps with various slopes and maintenance times at the fixed potential. All processes lasted five minutes. The innovative character of this research work is the evaluation of the combined effect of the anodizing voltage and its different trends with time on the coating structure and morphology. The corrosion resistance of coated AA6082 is assessed in contact with chlorides, reproducing seawater. The resulting anodic coatings were compared in terms of structure, composition (thickness, XRD, SEM-EDS) and corrosion resistance (potentiodynamic polarization and electrochemical impedance spectroscopy), finding that longer maintenance at high anodizing potentials promotes localized high-energy plasma discharges, producing larger pores and thicker, but less protective coatings. Results show that the coating thickness increases with the maintenance time (maximum thickness value~17.6 μm). Shorter maintenance periods and longer voltage ramps lead to a lower surface porosity and enhanced corrosion performances of the oxide. The thinnest and least porous coating exhibits the best corrosion behavior (CR~1.1 μm/year). Full article

The current research developed an optical carbon dioxide (CO₂) sensor using anodized aluminum oxide (AAO) as the substrate. We developed an optical carbon dioxide (CO₂) sensor utilizing CdSe/ZnS quantum dots (QDs) as the fluorescent dye and Phenol Red as the pH indicator. The QDs acted as the CO₂-responsive fluorophore and were embedded in a polyimide butyl methacrylate (polyIBM) matrix. This sensing solution was applied to an anodized aluminum oxide (AAO) substrate, which provided a porous and stable platform for sensor fabrication. Photoluminescence measurements were conducted using the coated AAO substrate, with excitation from a 405 nm LED light source. The sensor exhibited red fluorescence emission at 570 nm and could detect CO₂ concentrations in the linear range of 0–100%. Experimental results showed that fluorescence intensity increased with CO₂ concentration, achieving a sensitivity of 211. A wavelength shift of 0.1657 nm/% was observed, indicating strong interactions among CO₂ molecules, Phenol Red, and the QDs within the AAO matrix. The sensor demonstrated a response time of 55 s and a recovery time of 120 s. These results confirm the effectiveness of this optical sensing approach in minimizing fluctuations from the excitation light source and highlight the potential of the AAO-supported QDs and Phenol Red composite as a reliable CO₂ sensing material. This advancement holds promise for applications in both medical and industrial fields. Full article

This study evaluates the wear and corrosion resistance of the Cu-50Ni-5Al alloy reinforced with CeO₂ nanoparticles for potential use as anodes in molten carbonate fuel cells (MCFCs). Cu–50Ni–5Al alloys were synthesized, with and without the incorporation of 1% CeO₂ nanoparticles, by the mechanical alloying method and spark plasma sintering (SPS). The samples were evaluated using a single scratch test with a cone-spherical diamond indenter under progressive normal loading conditions. A non-contact 3D surface profiler characterized the scratched surfaces to support the analysis. Progressive loading tests indicated a reduction of up to 50% in COF with 1% NPs, with specific values drop-ping from 0.48 in the unreinforced alloy to 0.25 in the CeO₂-doped composite at 15 N of applied load. Furthermore, the introduction of CeO₂ decreased scratch depths by 25%, indicating enhanced wear resistance. The electrochemical behavior of the samples was evaluated by electrochemical impedance spectroscopy (EIS) in a molten carbonate medium under a H₂/N₂ atmosphere at 550 °C for 120 h. Subsequently, the corrosion products were characterized using X-ray diffraction (XRD), scanning electron microscopy coupled with energy dispersive spectroscopy (SEM-EDS), and X-ray photoelectron spectroscopy (XPS). The results demonstrated that the CeO₂-reinforced alloy exhibits superior electro-chemical stability in molten carbonate environments (Li₂CO₃-K₂CO₃) under an H₂/N₂ atmosphere at 550 °C for 120 h. A marked reduction in polarization resistance and a pronounced re-passivation effect were observed, suggesting enhanced anodic protection. This effect is attributed to the formation of aluminum and copper oxides in both compositions, together with the appearance of NiO as the predominant phase in the materials reinforced with nanoparticles in a hydrogen-reducing atmosphere. The addition of CeO₂ nanoparticles significantly improves wear resistance and corrosion performance. Recognizing this effect is vital for creating strategies to enhance the material’s durability in challenging environments like MCFC. Full article