Search Results (204)

Persistent reactive azo dyes released from textile finishing are a serious threat to water systems, but effective methods using sunlight to break them down are still limited. Everzol Yellow 3RS (EY-3RS) is particularly recalcitrant: past studies have relied almost exclusively on physical adsorption onto natural or modified clays and zeolites, and no photocatalytic pathway employing engineered nanomaterials has been documented to date. This study reports the synthesis, characterization, and performance of a visible-active ternary nanocomposite, Cu₄O₃/ZrO₂/TiO₂, prepared hydrothermally alongside its binary (Cu₄O₃/ZrO₂) and rutile TiO₂ counterparts. XRD, FT-IR, SEM-EDX, UV-Vis, and PL analyses confirm a heterostructured architecture with a narrowed optical bandgap of 2.91 eV, efficient charge separation, and a mesoporous nanosphere-in-matrix morphology. Photocatalytic tests conducted under midsummer sunlight reveal that the ternary catalyst removes 91.41% of 40 ppm EY-3RS within 100 min, markedly surpassing the binary catalyst (86.65%) and TiO₂ (81.48%). Activity trends persist across a wide range of operational variables, including dye concentrations (20–100 ppm), catalyst dosages (10–40 mg), pH levels (3–11), and irradiation times (up to 100 min). The material retains ≈ 93% of its initial efficiency after four consecutive cycles, evidencing good reusability. This work introduces the first nanophotocatalytic strategy for EY-3RS degradation and underscores the promise of multi-oxide heterojunctions for solar-driven remediation of colored effluents. Full article

Cobalt and Nickel (Co, Ni) co-doped magnesium oxide (MgO) nanoparticles (NPs) have been synthesized using the coprecipitation method. The structural, chemical, and optical properties of the as-synthesized NPs are systematically investigated using X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), and UV-visible spectroscopy. It is found that the optical bandgap of co-doped MgO NPs reduces from 2.30 to 1.98 eV (14%) with increasing Ni dopant concentrations up to 7%. The Co_0.05Ni_0.07Mg_0.88O NPs exhibit a high photocatalytic degradation efficiency of 93% for methylene blue dye (MB) under natural sunlight irradiation for 240 min. Our findings indicate that the Co_0.05Ni_xMg_0.95−xO NPs have strong potential for use as photocatalysts in industrial wastewater treatment. Full article

The present study investigates dye-sensitized solar cells (DSSCs) incorporating natural extracts from the microalgae Spirulina and Chlorella as photosensitizers. TiO₂-based electrodes were prepared and immersed in methanolic algae extracts for 24 and 48 h. UV–Vis spectroscopy revealed absorption peaks near 400 nm and 650 nm, characteristic of chlorophyll. Electrochemical analyses, including photochronoamperometry and open-circuit potential, confirmed the photosensitivity and charge transfer capabilities of all systems. The cell sensitized with Chlorella after 48 h of immersion exhibited the highest energy conversion efficiency (0.0184% ± 0.0015), while Spirulina achieved 0.0105% ± 0.0349 after 24 h. Chlorella’s superior performance is attributed to its higher chlorophyll content and enhanced light absorption, facilitating more efficient electron injection and interaction with the TiO₂ surface. Although the efficiency remains lower than that of conventional silicon-based solar cells, the results highlight the potential of natural colorants as sustainable and low-cost alternatives for photovoltaic applications. Nonetheless, further, improvements are required, particularly in dye stability and anchorage, to improve device performance. This research reinforces the viability of natural photosensitizers in DSSC technology and supports continued efforts to optimize their application. Full article

In this study, the degradation of Nile Blue dye was investigated using homogeneous and heterogeneous photocatalytic methods based on the photo-Fenton reaction. More specifically, for homogeneous photocatalysis, the classical photo-Fenton (UV/Fe²⁺/H₂O₂) and modified photo-Fenton-like (UV/Fe²⁺/S₂O₈²⁻) systems were studied, while for heterogeneous photocatalysis, a commercial MOF catalyst, Basolite F300, and a natural ferrous mineral, geothite, were employed. Various parameters—including the concentrations of the oxidant and catalyst, UV radiation, and pH—were investigated to determine their influence on the reaction rate. In homogeneous systems, an increase in iron concentration led to an enhanced degradation rate of the target compound. Similarly, increasing the oxidant concentration accelerated the reaction rate up to an optimal level, beyond which radical scavenging effects were observed, reducing the overall efficiency. In contrast, heterogeneous systems exhibited negligible degradation in the absence of an oxidant; however, the addition of oxidants significantly improved the process efficiency. Among the tested processes, homogeneous techniques demonstrated a superior efficiency, with the conventional photo-Fenton process achieving complete mineralization within three hours. Kinetic analysis revealed pseudo-first-order behavior, with rate constants ranging from 0.012 to 0.688 min⁻¹ and correlation coefficients (R²) consistently above 0.90, confirming the reliability of the applied model under various experimental conditions. Nevertheless, heterogeneous techniques, despite their lower degradation rates, also achieved high removal efficiencies while offering the advantage of operating at a neutral pH without the need for acidification. Full article

This study focuses on the stabilization of a natural hair dye derived from Lawsonia inermis L. (henna) and Indigofera suffruticosa (indigo). Although various formulations already exist, they are designed for immediate use and cannot be stored. Lawsonia, a primary component of the dye, tends to degrade after release. To ensure its stability, freeze-drying was implemented as a protective measure. Colorimetric analysis confirmed the dye’s ability to maintain an intense, uniform coloration even after multiple washing cycles. Stability tests demonstrate that freeze-drying effectively enhances the dye’s stability and capacity to retain its physical properties and color under various environmental conditions, demonstrating its potential for long-term use. The dye’s pH (5.05) aligns with the natural pH of hair, promoting cuticle sealing and improving hair health. Cytotoxicity tests confirmed the dye’s safety, showing no harmful effects. Gray hair exhibited a total color difference (ΔE) of 64.06 after the initial application, using natural gray hair as a reference. By the third application, ΔE increased to 69.86 and gradually decreased to 68.20 after 15 washing cycles, highlighting its long-term durability. Gray hair exposed to 720 h of UV radiation showed a ΔE of 17.34, whereas dyed gray hair exhibited a ΔE of 2.96 compared to non-UV-exposed samples. This indicates superior resistance to color degradation in dyed hair. Also, SEM imaging revealed the dye’s restorative effects, progressively improving hair cuticle structure with each application. Full article

Zinc oxide (ZnO) photocatalysts are recognized for their ease of synthesis, cost-effectiveness, efficiency, scalability, and environmental compatibility, making them highly suitable for addressing wastewater contamination. In this study, various compositions of kaolinite were used for the hydrothermal deposition of ZnO, including 0.5%, 0.75%, 1%, and 1.25%. The main purpose of this study was to evaluate the effect of kaolinite toward the enhanced performance of ZnO through modification of particle size, morphology and surface functional groups. Several analytical techniques were employed to obtain structural and optical results, including scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, and UV–visible spectroscopy, revealing significant changes in particle shape, particle size, surface functional groups, and optical band gap when kaolinite was added. The ZnO/kaolinite composite (sample 4) with 1.25% kaolinite content demonstrated outstanding photocatalytic performance for the degradation of methylene blue in natural sunlight. For sample 4, 15 mg of the dye in a 3.4 × 10⁻⁵ M dye solution exhibited a degradation efficiency of 99%. In contrast, when using 15 mg of catalyst dose and 1.5 × 10⁻⁵ M dye solution, the degradation efficiency was observed to be almost 100%, thus indicating that catalyst dose and dye concentration affect degradation efficiency. The reusability test revealed that sample 4 retained degradation efficiency of 98% after five cycles without showing any morphological changes. By decorating ZnO with kaolinite mineral clay, this study provides exciting findings and insights into the development of low-cost photocatalysts, which could be used to produce solar-powered hydrogen and treat wastewater. Full article

This study investigates a sustainable approach to the photocatalytic degradation of Congo red (CR) dye using titanium dioxide (TiO₂) under simulated solar radiation, with a specific focus on the UV-A component of the radiation. The aim was to optimize reaction conditions to maximize dye removal efficiency while promoting environmentally friendly wastewater treatment practices. A central composite design (CCD) was implemented, and results were analyzed using analysis of variance (ANOVA). The key factors examined included TiO₂ concentration, UV-A radiation intensity, CR dye concentration, and suspension depth. The optimal conditions determined were 222.37 mg/L TiO₂, 20 W/m² UV-A irradiation, 25 µmol/L CR dye concentration, and a suspension depth of 29 mm. Under these conditions, decolorization was achieved with the lowest absorbance (0.367 at 498 nm) and total organic carbon (0.805 mg/L) values, indicating effective dye degradation. The findings confirm that TiO₂-assisted photocatalysis is a green and promising method for wastewater treatment. The potential use of natural solar radiation could reduce operational costs, making the process more sustainable. However, challenges such as photocatalyst recovery, aggregation, and the impact of the real wastewater matrices need further investigation. Full article

Nitrogen and sulfur-co-doped carbon dots (N, S-CDs) were synthesized using a simple, eco-friendly hydrothermal technique with L-cysteine as the precursor. The synthesis approach produced highly water-dispersible, heteroatom-doped CDs with surface functional groups comprising amine, carboxyl, thiol, and sulfonic acid. Data analysis of X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), and transmission electron microscopy (TEM) confirmed their amorphous nature, nanoscale dimensions (1–8 nm, average particle size of 2.6 nm), and surface chemistry. Optical examination revealed intense and pure blue fluorescence emission under UV excitation, with excitation-dependent emission behavior attributed to surface defects and heteroatom doping. The N, S-CDs were applied as fluorescent probes for detecting perfluorooctanesulfonic acid (PFOS), a notable component of the perfluoroalkyl substances (PFAS) family, demonstrating pronounced and concentration-dependent fluorescence quenching. A linear detection range of 3.33–20 µM and a limit of detection (LOD) of 2 µM were reported using the N, S-CDs probe. UV-Vis spectral shifts and dye-interaction investigations indicated that the sensing mechanism is regulated by non-covalent interactions, primarily electrostatic and hydrophobic forces. These findings confirm the potential of N, S-CDs to be used as effective optical sensors for detecting PFOS in environmental monitoring applications. Full article

To enhance the photocatalytic performance of ZnO, the ZnO/g-C₃N₄ (ZCN) composite was prepared by ZnO and g-C₃N₄ under ball milling, and then the ternary graphene oxide (GO)/ZnO/g-C₃N₄ (GZCN) composite was achieved by using sonicating, stirring, and liquid phase evaporating. The photocatalytic performance was tested under UV light and natural solar light, respectively. The experimental results displayed that the GZCN composite revealed excellent photocatalytic performance under UV light and natural sunlight. When the ratio of ZnO to g-C₃N₄ is 1:0.2 and the mass fraction of graphene oxide is 0.25% in GZCN composite, the modified ZnO possesses optimal photocatalytic activity under UV light or natural solar light. RhB dye is degraded by 94% within 20 min under UV light, which is 3.41 times that of pure ZnO. Moreover, GZCN can degrade 88% of RhB in 60 min under natural sunlight. The enhancement for photocatalytic activity is attributed to the excellent conductivity of GO and heterojunction interaction between ZnO and g-C₃N₄, where the special electronic structure of g-C₃N₄ expands the spectral response range of ZnO and accelerates the transmission of photogenerated electrons and holes. Full article

As far as history tells, people have set efforts both to improve the conditions and to change the visual outfit of the skin, nails, and hair. The first information on nail cosmetics is found in ancient China and Egypt, where various nature-derived compositions were used for changing the colour of the nails. Nowadays more mechanically and chemically durable systems for nail polishes are elaborated. This review focuses on the latest achievements in the field of UV-curable nail polishes. Herein, the polymerization mechanisms of various systems (acrylates, as well as epoxides and thiols) occurring in nail polishes are described. Besides plausible side reactions of the polymerization process are characterized. Thus, the main drawbacks for forming a uniform, perfect layer are illuminated. For effective curing, the choice of photoinitiators may be crucial; thus, various types of photoinitiators as well as their main advantages and disadvantages are characterized. Ensuring effective adhesion between the substrate (human nail) and the polymer film is one of the challenges for the nail polish industry—thus the plausible interactions between the adhesion promoters and the keratin are described. Regarding the film-forming agents, a comprehensive overview of the composition of the traditional UV-curing nail polishes is provided, but the main emphasis is devoted to alternative, nature-derived film-forming agents that could introduce renewable resources into nail cosmetics. Additionally, this review gives short insight into the latest innovations in UV-curing nail cosmetics, like (1) nail polishes with improved pealability, (2) covalently polymer-bonded dyes and photoinitiators, thus reducing the release of the low-molecular compounds or their degradation products, and (3) UV-curing nail polishes as delivery systems for nail treatment medicine. Full article

The development of advanced high-capacity nanoparticle-based drug loading, precise targeting, low toxicity, and excellent biocompatibility is critical for improving cancer therapeutics. Withaferin A, a natural steroidal lactone derived from Physalis minima, exhibits potential biological activity and holds promise as a therapeutic agent. In this study, a novel nanoconjugate (NC) was developed using gold nanoparticles (AuNPs) functionalized with polyvinylpyrrolidone (PVP), Withaferin A drug, and folic acid for targeted drug delivery in cancer treatment. The AuNPs–PVP–Withaferin A–FA nanoconjugate was synthesized through a layer-by-layer assembly process and was confirmed using UV–visible and FTIR spectroscopy. The hydrodynamic radius, surface charge, and morphology of the NC were characterized using dynamic light scattering (DLS), zeta potential analysis, and electron microscopy, respectively. The nanoformulation demonstrated a pH-responsive drug release, with 92% of Withaferin A released at pH 5, mimicking the tumor microenvironment. In vitro cytotoxicity studies conducted on MCF-7 cells using MTT assays, dual dye staining, and protein expression analysis revealed that the nanoconjugate effectively induced apoptosis in cancer cells. These outcomes emphasize the prospect AuNPs–PVP–Withaferin A–FA nanoconjugate as a targeted and efficient Withaferin A delivery system for cancer therapy, leveraging the inherent anticancer properties of Withaferin A. Full article

A significant development has been the integration of natural elements with bio-based materials to produce entirely bio-based functional textiles. In this investigation, lycopene, derived from tomatoes, is used as a new natural red dye for silk. A suitable solvent was selected to precisely measure the lycopene content in silk. The stability of lycopene in a simulated dye bath was examined in relation to heating duration and pH values. Central composite design was employed to evaluate the impact of dyeing conditions on the color intensity of silk. The results showed that lycopene dissolves more efficiently in dichloromethane than in water or ethanol. UV–Vis absorption spectra, which remained nearly constant, indicate that lycopene retains its stability after being heated at 90 °C for 60 min or when the pH is between 3.2 and 6.2. Higher temperatures lead to increased lycopene adsorption, thereby enhancing color intensity. Based on the ANOVA analysis from the central composite design experiment, the most influential factor affecting color intensity is the concentration of lycopene, followed by temperature, and then pH. As the lycopene concentration increases, the color intensity and saturation of the dyed silk also increase. Although the lycopene-dyed silk shows good wash fastness, there is room for improvement in rub fastness. In summary, this study confirms the potential of using lycopene as a new natural red dye for silk. Full article

This study investigates the green synthesis of zinc oxide nanoparticles (ZnO NPs) using leaf extract as a natural reducing agent, evaluating their antimicrobial and photocatalytic properties. The nanoparticles were annealed at 320 °C and 500 °C, and the effects of leaf extract concentration and annealing temperature on their structural, morphological, and electronic properties were systematically explored. X-ray diffraction (XRD) analysis confirmed the hexagonal wurtzite structure of ZnO, with crystallite size and defect density being influenced by the concentration of the extract. Scanning electron microscopy (SEM) revealed the formation of smaller, spherical particles, with increased aggregation observed at higher extract concentrations. Fourier-transform infrared spectroscopy (FTIR) identified key functional groups, such as hydroxyl groups, C–O bonds, and metal–oxygen vibrations. UV–Vis spectroscopy showed a reduction in band gap energy and an increase in Urbach energy as the extract concentration and annealing temperature were increased. The antimicrobial activity of the ZnO NPs was evaluated against Gram-positive and Gram-negative bacteria as well as Candida albicans, demonstrating significant antibacterial efficacy. Photocatalytic degradation studies of methylene blue dye revealed a superior efficiency of up to 74% for the annealed samples, particularly at 500 °C. This research highlights the potential of green-synthesized ZnO NPs for a wide range of applications, including antimicrobial agents, water purification, and environmental catalysis. It contributes to the advancement of sustainable nanotechnology, offering promising solutions for both technological and ecological challenges. Full article

In this study, three dinuclear copper(II) complexes of ligand 2,6-bis[(N-methyl-piperazine-1-yl)methyl]-4-formyl phenol (L1) and one of 2,6-bis[(N-methylpiperazine-1-yl)methyl]-4-formyl phenol dimethylacetal (L2) with copper(II) ions have been investigated as new types of biomimetic catalysts for the oxidative transformation of different aminophenols and phenyldiamines. All the complexes of interest were newly synthesized and further characterized by IR spectroscopy, UV-Vis and mass spectrometry, X-ray diffraction, and selected electrochemical measurements. Crystal structures of these dinuclear copper(II) complexes have revealed that the coordination-shell geometry of copper atoms is close to a tetragonal pyramid. Catecholase, phenoxazinone synthase, and horseradish peroxidase-like activities were observed in pure methanol and water–methanol mixtures in the presence of molecular oxygen. The potential applicability of the complexes under study is discussed with respect to their possibilities and limitations in the replacement of natural copper-containing oxidoreductases in the oxidative degradation of water-insoluble chlorinated aminophenols in the dye industry or in the production of phenoxazine-based drugs. Full article

Increasing awareness of protecting the environment from chemically aided naive ecosystem degradation has encouraged the use of eco-friendly (biomass) materials in industrial production globally. This study investigated the application of a natural wine-colored extract from Brazilian plume (BP) leaf, obtained through a microwave-assisted modern aqueous extraction technique, for toxic-free dyeing of mordant-functionalized cotton fabric. Dyeing of mordanted cotton fabric was optimized by varying dyeing parameters, such as dyeing contact time (10 to 90 min), pH (1 to 11), liquor ratio (1:5 to 1:30), and temperature (30 to 90 °C). UV-visible and Fourier transform infrared spectroscopic analyses confirmed that the chemical constituents of the extract were not altered by microwave radiation. The desired color strength ($K/S$) and dye-uptake (Q) were obtained at a dyeing time of 50 min, a pH of 7, a liquor ratio of 1:20, and a dyeing temperature of 60 °C. Varieties of elegant shades with desired colorfastness were developed through the involvement of less-toxic electrolyte and herbal mordants as functionalizing agents. BP extract is established as a potential sustainable and ecological colorant for textile industrial application. Full article