Search Results (371)

This study presents a method to retrieve the electron density structure of the transient C-region using very-low-frequency (VLF) Earth–ionosphere waveguide propagation. Here, we demonstrate the identification of the C-region from amplitude variations of a mid-range VLF propagation path that is nearly perpendicular to the solar terminator. Previous investigations have primarily relied on phase measurements along long-distance paths with small terminator angles, whereas the present approach utilizes amplitude information under conditions where modal interference is significant. The Faraday International Reference Ionosphere (FIRI-2018) provides an effective semi-empirical model of the lower-ionospheric electron density; however, discrepancies between simulations and observations are often observed at sunrise. To resolve this issue, we introduce Gaussian perturbations to the electron density profile output by FIRI-2018 and optimize their parameters so that finite-difference time-domain (FDTD) simulations reproduce the observed VLF amplitude. The analysis is performed for the 22.2 kHz JJI transmitter signal received in Chofu, Japan over a mid-range propagation path, ∼900 km. The optimized electron density profile successfully reproduces the characteristic features of the C-region, including a temporary enhancement near 65 km altitude during sunrise. These results demonstrate that mid-range VLF amplitude analysis provides a quantitative tool for identifying transient lower- ionospheric structures. Full article

This study presents a computational, simulation-based investigation of the dielectric response of human hand tissues, skin, fat, muscle, and bone to radiofrequency (RF) electromagnetic fields emitted by mobile devices. The widespread adoption of handheld devices and the deployment of fifth-generation (5G) networks, including millimetre-wave (mmWave) bands, have intensified concerns regarding localized human exposure to RF radiation, particularly in the hand, which serves as the primary interface during device operation. Using validated dielectric property datasets, numerical simulations were performed across the frequency range of 0.5–40 GHz, employing the Finite-Difference Time-Domain (FDTD) method to solve Maxwell’s equations, with analytical evaluations conducted in Maple-18. A heterogeneous multilayer hand phantom was developed, and simulations were conducted under controlled exposure conditions, including a transmitted power of 1 W, antenna gain of 2 dBi, and incident power density of 5 W/m², consistent with ICNIRP and NCC safety guidelines. Tissue responses were assessed over a temperature range of 10–40 °C to account for thermal variability. The results demonstrate strong frequency- and temperature-dependent behaviour of dielectric properties, intrinsic impedance, reflection coefficient, attenuation, and specific absorption rate (SAR). At lower frequencies (<1 GHz), RF energy penetrated more deeply with distributed absorption and relatively low SAR values, whereas higher frequencies (3–40 GHz) produced highly localized absorption in superficial tissues, particularly skin and muscle. Increasing temperature led to significant increases in permittivity, conductivity, and SAR, with up to a twofold enhancement observed between 10 °C and 40 °C. These findings confirm that 5G and mmWave exposures result in predominantly surface-confined energy deposition in hand tissues. The study provides a robust computational framework for evaluating hand device electromagnetic interactions and offers quantitative insights relevant to antenna design, exposure compliance assessment, and the development of evidence-based safety guidelines. Full article

Periodic supercell lattice structures with elements of random polydispersity disorder were created to simulate the effect of randomization on photonic crystals using finite-difference time domain (FDTD) methods. As a key exemplar system, a three-dimensional “inverse opal” structure of a face-centered cubic lattice with air spheres in a silicon dielectric was simulated, with sphere radii within supercells following a randomized Gaussian distribution, with characteristic standard deviation and mean. A corresponding ordered lattice with a bandgap with magnitude 3.5% of the normalized frequency range was used as a direct control, with sphere radius 0.34 times the lattice constant a. For a range of standard deviations, up to 5.9% of the 0.34a mean, a Monte Carlo-style approach was adopted, with photonic band properties analyzed over a large number of repeat simulations to ensure statistical significance. The corresponding Gaussian distribution in the resultant photonic bandgap magnitudes is broadened with increasing polydispersity such that an evolving fraction of simulations no longer exhibits a non-zero bandgap. A characteristic pseudo-transition occurs at a standard deviation of approximately 4.1% of the 0.34a mean, above where the frequency of simulations still returning a finite bandgap rapidly diminishes. Some isolated configurations, with a high degree of uniqueness, can exhibit enhanced bandgap properties (greater than the 3.5% benchmark) despite considerable polydisperse disordering; we envisage that these findings point towards the use of engineered randomness in supercell systems to create desired photonic crystal properties and functionality, such as localization and photonic bandgaps. Full article

When examining ground-penetrating radar (GPR)-based advanced detection ahead of the tunnel face for tunnel constructions, existing numerical forward simulations have not effectively accounted for the actual orientation of the strata and the conditions, limiting their theoretical guidance. In this study, we classify tunnel boring through strata attitudes into horizontal, vertical, positively inclined, reverse inclined, and other anomalous structures. We also consider tunnel faces with different planarity (perfectly smooth or irregular). Using the finite-difference time-domain method with a generalized perfectly matched layer, we simulated 21 forward models for GPR-based advanced detection ahead of the tunnel face. The comparative simulation results indicate that the superposition of reflections from different directions at irregular tunnel faces, lithological interfaces, complicated numerical forward models of typical target geological bodies, making it difficult to distinguish the reflection signals of target geological bodies, and the signal strength in numerical forward modeling profiles with antenna touch with tunnel face is significantly stronger than those without such touch. The flatness of the tunnel face and the close proximity between the antenna and tunnel face are the keys to obtain high-quality original data. These research findings will contribute to improving instruments, data processing, and geologic interpretation in future. Full article

We systematically investigate semiclassical dynamics of the optical field produced by quantum nanoemitters (NEs) embedded in a periodic lattice of conducting nanorings (NRs), in which plasmon polaritons (PPs) are excited. The coupling between PPs and NEs through the radiated optical field leads to establishment of a significant cross-correlation between NEs, so that their internal dynamics (photocurrent affected by the laser irradiation) depends on the NR’s plasma frequency ${\omega }_p$. The transition to this regime, combined with the nonlinearity of the system, leads to a quite increase in the photocurrent in the NEs, as well as to non-smooth (chimera-like or chaotic) behavior in the critical (transition) region, where considerably small variations in ${\omega }_p$ lead to significant changes in the level of the NE pairwise cross-correlations. The chimera-like state is realized as coexistence of locally synchronized and desynchronized NE dynamical states. A fit of the dependence of the critical current on ${\omega }_p$ is found, being in agreement with results of numerical simulations. The critical effect may help to design new optical devices, using dispersive nanolattices which are made available by modern nanoelectronics. Full article

Firm requirements on electromagnetic compatibility (EMC) of electronic devices demand low electromagnetic emissions (EMI) of high-speed circuits, especially in the automotive industry. To be able to apply cost-effective anti-perturbative measures that reduce noise emission, critical signal integrity and power integrity (SI/PI) tools are needed for developing high-speed printed circuit board (PCB) designs. This paper presents an efficient method for modeling and analyzing the current drawn by digital ICs based on SPICE modeling data. The profile of the current drawn by the ICs from the power supply is composed of the static supply current and the dynamic supply current. This method enables power integrity engineers, in particular, PhD students and researchers who aim to develop an intuitive understanding of PI phenomena during the pre-layout phase, to see the hidden impact of the supply current on the power rail noise through time domain simulations, using a complex simulation model that integrates the Finite-Difference Time-Domain (FDTD) method of modeling the power and ground plane, with Voltage Regulator Modules (VRMs) and decoupling capacitors. A comparison of simulation results between the proposed models and SPICE IC models is also included to validate the proposed model. Full article

Solar energy stands as one of the most promising green energy sources today. This paper proposes a symmetrical gap-type separated solar absorber and radiator (SETR) featuring a dielectric layer of Al₂O₃ and metal W as separation columns. Its unique structure enhances absorption within the effective solar energy spectrum, thereby alleviating solar energy absorption challenges. The finite difference time domain method (FDTD) results show that the SETR achieves an absorption rate of more than 90% in the 280–2096 nm band, which perfectly covers the visible light band range. The weighted average absorption in the 280–2500 nm band is 95.22% under AM1.5 conditions. The thermal emission efficiency at 1500 K is 95.13%, and the thermal radiation loss is less than 5%. Beyond analyzing the results, we also investigated the overall band absorption efficiency of the SETR under varying conditions by adjusting its structural parameters and physical parameters such as materials. This approach enables effective control over the absorption spectrum. Additionally, the proposed SETR is independent of polarization conditions. Both the TM and TE modes are insensitive to large incident angles. In the future, broadband SETRs can be applied to solar energy harvesting, thermoelectric conversion, and imaging fields, as it holds broad application prospects. Full article

Light-emitting diodes (LEDs) are becoming increasingly important across various sectors of the lighting industry and are being used more frequently. In the field of symbolic projection, research is increasingly focusing on implementing light modulation using energy-efficient, incoherent LEDs rather than lasers. Since light modulation in micro- and nano-optics is typically achieved through phase modulation, Finite-Difference Time-Domain (FDTD) simulations are employed for analysis. The objective of this article is to investigate different approaches for approximating incoherent monochromatic light sources within FDTD simulations. To this end, two approaches based on dipole sources are considered, as well as a method involving plane waves with modulated wavefronts based on Cosine–Fourier functions and a method based on the superposition of Gaussian beams. These methods are evaluated in terms of their accuracy using a two-dimensional double-slit configuration and are compared against a fully incoherent analytical reference. Full article

During coal mining, detecting subsurface structures (such as faults, voids, collapse columns, etc.) using radio waves in existing mines is hindered by the absence of effective three-dimensional coal seam medium models and simulation methods, adversely affecting the forward modeling of data analysis. This study establishes a Three-Dimensional Finite-Difference Time-Domain (3D-FDTD) radio wave penetration medium model based on coal seam tunnel penetration working conditions to simulate the electric field intensity characteristics of longitudinal and transverse waves in various coal rock mediums. Firstly, a higher-order finite difference method based on Maxwell’s equations is employed to analyze the electric field characteristics of gas-enriched areas under various geological conditions, enabling the exploration of the relationship between the position and size of the electromagnetic wave field strength in different areas. The electromagnetic wave field strength response data are then analyzed during the actual detection process to determine the specific location, shape, and size of the abnormal area. Finally, by comparing the simulation results with an actual engineering project, electromagnetic wave field strength attenuation data were collected from 158 measuring points at a working face of a coal mine in Anhui. The detection results clearly illustrate the changes in electric field intensity (with attenuation coefficients ranging from 0.41 to 0.77 dB/m) in anomalous areas, enabling the forward simulation to accurately determine the position and size of faults. The novelty of this study lies in the establishment of a conductivity-weighted 3D-FDTD model specifically calibrated for complex coal seam environments, which significantly improves the accuracy of fault boundary detection compared to traditional linear inversion methods. Full article

Herein, we propose a simple and cost-effective method for fabricating moderate-sensitivity surface-enhanced Raman scattering (SERS) substrates using Cu-plasma polymer fluorocarbon (Cu-PPFC) nanocomposite films fabricated through RF sputtering. The use of a composite target composed of carbon nanotube (CNT), Cu, and polytetrafluoroethylene (PTFE) powders (5:60–80:35–15 wt%) offers the advantage of the simple fabrication of moderate-sensitivity SERS substrates with a single cathode compared to co-sputtering. X-ray photoelectron spectroscopy (XPS) revealed that the film surface was partially composed of metallic Cu with Cu-F bonds and Cu–O bonds, confirming the coexistence of the conducting and plasmon-active domains. UV-VIS spectroscopy revealed a distinct absorption peak at approximately 680 nm, indicating the excitation of localized surface plasmon resonances in the Cu nanoclusters embedded in the plasma polymer fluorocarbon (PPFC) matrix. Atomic force microscopy and grazing incidence small-angle X-ray scattering analyses confirmed that the Cu nanoparticles were uniformly distributed with interparticle distances of 20–35 nm. The Cu-PPFC nanocomposite film with the highest Cu content (80 wt%) exhibited a Raman enhancement factor of 2.18 × 10⁴ for rhodamine 6G, demonstrating its potential as a moderate-sensitivity SERS substrate. Finite-difference time-domain (FDTD) simulations confirmed the strong electromagnetic field localization at the Cu-Cu nanogaps separated by the PPFC matrix, corroborating the experimentally observed SERS enhancement. These results suggest that a Cu-PPFC nanocomposite film, easily fabricated using a composite target, provides an efficient and scalable route for fabricating reproducible, inexpensive, and moderate-sensitivity SERS substrates suitable for practical sensing applications. Full article

The interaction between laser irradiation and energetic materials is critically influenced by microstructural void defects that determine local energy deposition and initiation sensitivity. In this work, a three-dimensional finite-difference time-domain (3D-FDTD) method was employed to investigate the modulation effects of void defects on optical field distributions and hot spot formation in RDX energetic crystals. The influences of void geometry, spatial position, and void number on the modulation of the incident laser beam were systematically analyzed. It reveals that void defects exhibit strong focusing and scattering behavior, leading to localized high-intensity regions both inside RDX bulk crystals and in void defects. For a single void defect, increasing either the width or depth can significantly enhance the peak electric field and thus the laser sensitivity of RDX crystals. When two voids are present, the number of high-intensity spots first increases and then decreases with increasing separation distance, and the strongest modulation effects are obtained at separations of 0.75λ–3λ. Furthermore, as the number of void defects increases, the modulation effect intensifies, promoting the formation of more hot spots. These findings provide quantitative insight into how void structures govern laser–matter interactions in energetic crystals, offering guidance for understanding and controlling laser initiation behavior. Full article

The atmospheric reentry of hypersonic vehicles generates a plasma sheath enveloping the vehicle surface. This fluid medium moves at velocities distinct from the vehicle body, significantly altering its electromagnetic scattering properties. This paper introduces a Multi-Frame Lorentz Transformation Finite-Difference Time-Domain (FDTD) method, which incorporates a spatially varying velocity field into the computational scheme. The proposed algorithm maintains velocity synchronization in electromagnetic field updates and employs a near-to-far-field transformation for far-zone analysis. We systematically investigate the scattering characteristics of a plasma-sheath-covered hypersonic vehicle across a range of velocities and analyze the effect of velocity on the Radar Cross-Section (RCS) under different polarization conditions. Full article

Based on the finite-difference time-domain (FDTD) method, this study investigates the propagation effects of lightning electromagnetic fields over mixed sea–land paths. A self-developed FDTD computational model is employed, which takes into account the influence of the Earth–ionosphere waveguide structure on the radiation field propagation. Through numerical simulations, the waveforms of the vertical electric field and azimuthal magnetic field of the lightning radiation during mixed-path propagation are obtained. The results demonstrate that under long-distance propagation conditions of 50 km, the discontinuity between land and sea media significantly distorts the electric field waveform, while the influence on the magnetic field waveform is negligible. This study provides a reliable numerical basis for analyzing the propagation characteristics of lightning radiation fields in complex terrain and offers valuable insights for lightning location and electromagnetic environment assessment. Full article

Partial discharge (PD) is not only the primary manifestation of insulation deterioration in gas-insulated switchgear (GIS) but also a critical indicator of the equipment’s insulation condition. PD in GIS typically occurs at media interfaces such as the surface of the basin insulator and is characterized by high randomness and low amplitude. Conventional built-in ultra-high frequency sensors exhibit limitations in early warning and detection performance. This study proposes and demonstrates a self-sensing shielding ring embedded within the basin insulator, functioning as a novel UHF sensor. Finite-difference time-domain (FDTD) is a numerical method used to solve problems involving electromagnetic fields. Based on actual GIS structural parameters, a FDTD simulation platform is constructed and a built-in sensor is used as a control to evaluate the receiving performance of the self-sensing shielding ring for PD signals. Time-domain array simulations are conducted to investigate the influence of radial, angular and axial positions on the observed performance. The results show that the proposed shielding ring exhibits broadband and low-reflection characteristics, achieving an average S₁₁ of −6.347 dB, which is significantly lower than those of the built-in sensors (−1.270 dB and −1.274 dB). The results demonstrate that the self-sensing shielding ring enables high sensitivity and the wideband detection of partial discharge, providing a new design approach and technical foundation for online early-warning systems in GIS. Full article

A three-dimensional Ag/TiO₂/Ti foam was fabricated via thermal annealing followed by pulsed laser deposition (PLD), providing a simple and scalable fabrication strategy. The porous Ti foam framework allows for the uniform dispersion of Ag nanoparticles (NPs), while the thermally formed TiO₂ interlayer promotes synergistic electromagnetic and chemical enhancement mechanisms. The localized electromagnetic field amplification at Ag-TiO₂ interfaces was simulated using the finite-difference time-domain (FDTD) method. Density functional theory (DFT) calculations confirmed that TiO₂ enhances both rhodamine 6G (R6G) adsorption on the substrate and charge transfer (CT) between the substrate and R6G, increasing the SERS activity. The optimized substrate demonstrates exceptional surface-enhanced Raman scattering (SERS) performance with an enhancement factor of 1.9 × 10⁷ and a detection limit of 2.24 × 10⁻¹¹ M for rhodamine 6G, with good reproducibility (RSD = 8.4%). Practical applicability is validated through sensitive detection of food colorants (brilliant blue and allura red). The synergistic combination of CT and electromagnetic enhancement in the easily fabricated Ag/TiO₂/Ti foam enables its application as a promising platform for food safety monitoring, effectively bridging laboratory innovation and practical applications. Full article