Sensors

Research

14 pages, 4607 KiB

Open AccessArticle

ZIF-8-Based Surface Plasmon Resonance and Fabry–Pérot Sensors for Volatile Organic Compounds

by Anna Estany-Macià, Ignasi Fort-Grandas, Nirav Joshi, Winnie E. Svendsen, Maria Dimaki, Albert Romano-Rodríguez and Mauricio Moreno-Sereno

Sensors 2024, 24(13), 4381; https://doi.org/10.3390/s24134381 - 5 Jul 2024

Viewed by 651

Abstract

This work explores the use of ZIF-8, a metal–organic framework (MOF) material, for its use in the optical detection of volatile organic compounds (VOCs) in Fabry–Pérot and surface plasmon resonance (SPR)-based sensors. The experiments have been carried out with ethanol (EtOH) and show [...] Read more.

This work explores the use of ZIF-8, a metal–organic framework (MOF) material, for its use in the optical detection of volatile organic compounds (VOCs) in Fabry–Pérot and surface plasmon resonance (SPR)-based sensors. The experiments have been carried out with ethanol (EtOH) and show response times as low as 30 s under VOC-saturated atmospheres, and the estimated limit of detection is below 4000 ppm for both sensor types. The selectivity towards other VOCs is relatively poor, although the dynamics of adsorption/desorption differ for each VOC and could be used for selectivity purposes. Furthermore, the hydrophobicity of ZIF-8 has been confirmed and the fabricated sensors are insensitive to this compound, which is a very attractive result for its practical use in gas sensing devices. Full article

(This article belongs to the Special Issue Chemical Sensors—Recent Advances and Future Challenges 2023–2024)

► Show Figures

Figure 1

15 pages, 8738 KiB

Open AccessArticle

Mixed-Potential Ammonia Sensor Based on a Dense Yttria-Stabilized Zirconia Film Manufactured at Room Temperature by Powder Aerosol Deposition

by Nils Donker, Daniela Schönauer-Kamin and Ralf Moos

Sensors 2024, 24(3), 811; https://doi.org/10.3390/s24030811 - 26 Jan 2024

Cited by 1 | Viewed by 847

Abstract

Powder aerosol deposition (often abbreviated as PAD, PADM, or ADM) is a coating method used to obtain dense ceramic films at room temperature. The suitability of this method to obtain ammonia mixed-potential sensors based on an yttria-stabilized zirconia (YSZ) electrolyte that is manufactured [...] Read more.

Powder aerosol deposition (often abbreviated as PAD, PADM, or ADM) is a coating method used to obtain dense ceramic films at room temperature. The suitability of this method to obtain ammonia mixed-potential sensors based on an yttria-stabilized zirconia (YSZ) electrolyte that is manufactured using PAD and a V₂O₅–WO₃–TiO₂ (VWT)-covered electrode is investigated in this study. The sensor characteristics are compared with data from sensors with screen-printed YSZ solid electrolytes. The PAD sensors outperform those in terms of sensitivity with 117 mV/decade NH₃ compared to 88 mV/decade. A variation in the sensor temperature shows that the NH₃ sensitivity strongly depends on the sensor temperature and decreases with higher sensor temperature. Above 560 °C, the characteristic curve shifts from exponential to linear dependency. Variations in the water and the oxygen content in the base gas (usually 10% oxygen, 2% water vapor in nitrogen) reveal a strong dependence of the characteristic curve on the oxygen content. Water vapor concentration variations barely affect the sensor signal. Full article

(This article belongs to the Special Issue Chemical Sensors—Recent Advances and Future Challenges 2023–2024)

► Show Figures

Figure 1

14 pages, 5391 KiB

Open AccessArticle

The Role of Zn Ions in the Structural, Surface, and Gas-Sensing Properties of SnO₂:Zn Nanocrystals Synthesized via a Microwave-Assisted Route

by Luís F. da Silva, Mattia A. Lucchini, Ariadne C. Catto, Waldir Avansi Jr., Sandrine Bernardini, Khalifa Aguir, Markus Niederberger and Elson Longo

Sensors 2024, 24(1), 140; https://doi.org/10.3390/s24010140 - 26 Dec 2023

Cited by 1 | Viewed by 1167

Abstract

Although semiconducting metal oxide (SMOx) nanoparticles (NPs) have attracted attention as sensing materials, the methodologies available to synthesize them with desirable properties are quite limited and/or often require relatively high energy consumption. Thus, we report herein the processing of Zn-doped SnO₂ NPs [...] Read more.

Although semiconducting metal oxide (SMOx) nanoparticles (NPs) have attracted attention as sensing materials, the methodologies available to synthesize them with desirable properties are quite limited and/or often require relatively high energy consumption. Thus, we report herein the processing of Zn-doped SnO₂ NPs via a microwave-assisted nonaqueous route at a relatively low temperature (160 °C) and with a short treatment time (20 min). In addition, the effects of adding Zn in the structural, electronic, and gas-sensing properties of SnO₂ NPs were investigated. X-ray diffraction and high-resolution transmission electron microscopy analyses revealed the single-phase of rutile SnO₂, with an average crystal size of 7 nm. X-ray absorption near edge spectroscopy measurements revealed the homogenous incorporation of Zn ions into the SnO₂ network. Gas sensing tests showed that Zn-doped SnO₂ NPs were highly sensitive to sub-ppm levels of NO₂ gas at 150 °C, with good recovery and stability even under ambient moisture. We observed an increase in the response of the Zn-doped sample of up to 100 times compared to the pristine one. This enhancement in the gas-sensing performance was linked to the Zn ions that provided more surface oxygen defects acting as active sites for the NO₂ adsorption on the sensing material. Full article

(This article belongs to the Special Issue Chemical Sensors—Recent Advances and Future Challenges 2023–2024)

► Show Figures

Figure 1

13 pages, 5226 KiB

Open AccessArticle

Biotinylated Quinone as a Chemiluminescence Sensor for Biotin-Avidin Interaction and Biotin Detection Application

by Fatema Kaladari, Mahmoud El-Maghrabey, Megumi Kawazato, Naoya Kishikawa and Naotaka Kuroda

Sensors 2023, 23(23), 9611; https://doi.org/10.3390/s23239611 - 4 Dec 2023

Cited by 2 | Viewed by 1242

Abstract

Biotin, or vitamin B7, is essential for metabolic reactions. It must be obtained from external sources such as food and biotin/vitamin supplements because it is not biosynthesized by mammals. Therefore, there is a need to monitor its levels in supplements. However, biotin detection [...] Read more.

Biotin, or vitamin B7, is essential for metabolic reactions. It must be obtained from external sources such as food and biotin/vitamin supplements because it is not biosynthesized by mammals. Therefore, there is a need to monitor its levels in supplements. However, biotin detection methods, which include chromatographic, immune, enzymatic, and microbial assays, are tedious, time-consuming, and expensive. Thus, we synthesized a product called biotin-naphthoquinone, which produces chemiluminescence upon its redox cycle reaction with dithiothreitol and luminol; then it was used as a chemiluminescence sensor for biotin–avidin interaction. When a quinone biotinylated compound binds avidin, the chemiluminescence decreases noticeably due to the proximity between quinone and avidin, and when free biotin is added in a competitive assay, the chemiluminescence returns. The chemiluminescence is regained as the free biotin displaces biotinylated quinone in its complex with avidin, freeing biotin-naphthoquinone. Many experiments, including the use of a biotin-free quinone, proved the competitive nature of the assay. The competitive assay method used in this study was linear in the range of 1.0–100 µM with a detection limit of 0.58 µM. The competitive chemiluminescence assay could detect biotin in vitamin B7 tablets with good recovery of 91.3 to 110% and respectable precision (RSD < 8.7%). Full article

(This article belongs to the Special Issue Chemical Sensors—Recent Advances and Future Challenges 2023–2024)

► Show Figures

Graphical abstract

15 pages, 2167 KiB

Open AccessArticle

Sex Determination of Human Nails Based on Attenuated Total Reflection Fourier Transform Infrared Spectroscopy in Forensic Context

by Bilkis Mitu, Václav Trojan and Lenka Halámková

Sensors 2023, 23(23), 9412; https://doi.org/10.3390/s23239412 - 26 Nov 2023

Cited by 1 | Viewed by 1322

Abstract

This study reports on the successful use of a machine learning approach using attenuated total reflectance Fourier transform infrared (ATR FT-IR) spectroscopy for the classification and prediction of a donor’s sex from the fingernails of 63 individuals. A significant advantage of ATR FT-IR [...] Read more.

This study reports on the successful use of a machine learning approach using attenuated total reflectance Fourier transform infrared (ATR FT-IR) spectroscopy for the classification and prediction of a donor’s sex from the fingernails of 63 individuals. A significant advantage of ATR FT-IR is its ability to provide a specific spectral signature for different samples based on their biochemical composition. The infrared spectrum reveals unique vibrational features of a sample based on the different absorption frequencies of the individual functional groups. This technique is fast, simple, non-destructive, and requires only small quantities of measured material with minimal-to-no sample preparation. However, advanced multivariate techniques are needed to elucidate multiplex spectral information and the small differences caused by donor characteristics. We developed an analytical method using ATR FT-IR spectroscopy advanced with machine learning (ML) based on 63 donors’ fingernails (37 males, 26 females). The PLS-DA and ANN models were established, and their generalization abilities were compared. Here, the PLS scores from the PLS-DA model were used for an artificial neural network (ANN) to create a classification model. The proposed ANN model showed a greater potential for predictions, and it was validated against an independent dataset, which resulted in 92% correctly classified spectra. The results of the study are quite impressive, with 100% accuracy achieved in correctly classifying donors as either male or female at the donor level. Here, we underscore the potential of ML algorithms to leverage the selectivity of ATR FT-IR spectroscopy and produce predictions along with information about the level of certainty in a scientifically defensible manner. This proof-of-concept study demonstrates the value of ATR FT-IR spectroscopy as a forensic tool to discriminate between male and female donors, which is significant for forensic applications. Full article

(This article belongs to the Special Issue Chemical Sensors—Recent Advances and Future Challenges 2023–2024)

► Show Figures

Graphical abstract

15 pages, 6575 KiB

Open AccessArticle

Synthesis of TiO₂-(B) Nanobelts for Acetone Sensing

by Gayan W. C. Kumarage, Shasika A. Panamaldeniya, Dileepa C. Maddumage, Abderrahim Moumen, Valentin A. Maraloiu, Catalina G. Mihalcea, Raluca F. Negrea, Buddhika S. Dassanayake, Nanda Gunawardhana, Dario Zappa, Vardan Galstyan and Elisabetta Comini

Sensors 2023, 23(19), 8322; https://doi.org/10.3390/s23198322 - 8 Oct 2023

Viewed by 1895

Abstract

Titanium dioxide nanobelts were prepared via the alkali-hydrothermal method for application in chemical gas sensing. The formation process of TiO₂-(B) nanobelts and their sensing properties were investigated in detail. FE-SEM was used to study the surface of the obtained structures. The [...] Read more.

Titanium dioxide nanobelts were prepared via the alkali-hydrothermal method for application in chemical gas sensing. The formation process of TiO₂-(B) nanobelts and their sensing properties were investigated in detail. FE-SEM was used to study the surface of the obtained structures. The TEM and XRD analyses show that the prepared TiO₂ nanobelts are in the monoclinic phase. Furthermore, TEM shows the formation of porous-like morphology due to crystal defects in the TiO₂-(B) nanobelts. The gas-sensing performance of the structure toward various concentrations of hydrogen, ethanol, acetone, nitrogen dioxide, and methane gases was studied at a temperature range between 100 and 500 °C. The fabricated sensor shows a high response toward acetone at a relatively low working temperature (150 °C), which is important for the development of low-power-consumption functional devices. Moreover, the obtained results indicate that monoclinic TiO₂-B is a promising material for applications in chemo-resistive gas detectors. Full article

(This article belongs to the Special Issue Chemical Sensors—Recent Advances and Future Challenges 2023–2024)

► Show Figures

Figure 1

Review

Jump to: Research, Other

19 pages, 4682 KiB

Open AccessReview

Effects of Visible Light on Gas Sensors: From Inorganic Resistors to Molecular Material-Based Heterojunctions

by Sujithkumar Ganesh Moorthy and Marcel Bouvet

Sensors 2024, 24(5), 1571; https://doi.org/10.3390/s24051571 - 29 Feb 2024

Cited by 3 | Viewed by 1101

Abstract

In the last two decades, many research works have been focused on enhancing the properties of gas sensors by utilising external triggers like temperature and light. Most interestingly, the light-activated gas sensors show promising results, particularly using visible light as an external trigger [...] Read more.

In the last two decades, many research works have been focused on enhancing the properties of gas sensors by utilising external triggers like temperature and light. Most interestingly, the light-activated gas sensors show promising results, particularly using visible light as an external trigger that lowers the power consumption as well as improves the stability, sensitivity and safety of the sensors. It effectively eliminates the possible damage to sensing material caused by high operating temperature or high energy light. This review summarises the effect of visible light illumination on both chemoresistors and heterostructure gas sensors based on inorganic and organic materials and provides a clear understanding of the involved phenomena. Finally, the fascinating concept of ambipolar gas sensors is presented, which utilised visible light as an external trigger for inversion in the nature of majority charge carriers in devices. This review should offer insight into the current technologies and offer a new perspective towards future development utilising visible light in light-assisted gas sensors. Full article

(This article belongs to the Special Issue Chemical Sensors—Recent Advances and Future Challenges 2023–2024)

► Show Figures

Figure 1

29 pages, 7438 KiB

Open AccessReview

Graphene-Based Chemiresistor Sensors for Drinking Water Quality Monitoring

by Mason McGarrity and Feng Zhao

Sensors 2023, 23(24), 9828; https://doi.org/10.3390/s23249828 - 14 Dec 2023

Cited by 1 | Viewed by 1422

Abstract

Monitoring the quality of drinking water is a crucial responsibility for all water infrastructure networks, as it guarantees access to clean water for the communities they serve. With water infrastructure deteriorating due to age and neglect, drinking water violations are on the rise [...] Read more.

Monitoring the quality of drinking water is a crucial responsibility for all water infrastructure networks, as it guarantees access to clean water for the communities they serve. With water infrastructure deteriorating due to age and neglect, drinking water violations are on the rise in the US, underscoring the need for improved monitoring capabilities. Among the different sensor technologies, graphene-based chemiresistors have emerged as a promising technology for water quality monitoring due to advantages such as simple design, sensitivity, and selectivity. This review paper provides an overview of recent advances in the development of graphene-based chemiresistors for water quality monitoring, including principles of chemiresistive sensing, sensor design and functionalization, and performance of devices reported in the literature. The paper also discusses challenges and opportunities in the field and highlights future research directions. The development of graphene-based chemiresistors has the potential to revolutionize water quality monitoring by providing highly sensitive and cost-effective sensors that can be integrated into existing infrastructure for real-time monitoring. Full article

(This article belongs to the Special Issue Chemical Sensors—Recent Advances and Future Challenges 2023–2024)

► Show Figures

Figure 1

Other

Jump to: Research, Review

22 pages, 7722 KiB

Open AccessPerspective

Chemically Functionalized 2D Transition Metal Dichalcogenides for Sensors

by Selene Acosta and Mildred Quintana

Sensors 2024, 24(6), 1817; https://doi.org/10.3390/s24061817 - 12 Mar 2024

Cited by 3 | Viewed by 1320

Abstract

The goal of the sensor industry is to develop innovative, energy-efficient, and reliable devices to detect molecules relevant to economically important sectors such as clinical diagnoses, environmental monitoring, food safety, and wearables. The current demand for portable, fast, sensitive, and high-throughput platforms to [...] Read more.

The goal of the sensor industry is to develop innovative, energy-efficient, and reliable devices to detect molecules relevant to economically important sectors such as clinical diagnoses, environmental monitoring, food safety, and wearables. The current demand for portable, fast, sensitive, and high-throughput platforms to detect a plethora of new analytes is continuously increasing. The 2D transition metal dichalcogenides (2D-TMDs) are excellent candidates to fully meet the stringent demands in the sensor industry; 2D-TMDs properties, such as atomic thickness, large surface area, and tailored electrical conductivity, match those descriptions of active sensor materials. However, the detection capability of 2D-TMDs is limited by their intrinsic tendency to aggregate and settle, which reduces the surface area available for detection, in addition to the weak interactions that pristine 2D-TMDs normally exhibit with analytes. Chemical functionalization has been proposed as a consensus solution to these limitations. Tailored surface modification of 2D-TMDs, either by covalent functionalization, non-covalent functionalization, or a mixture of both, allows for improved specificity of the surface–analyte interaction while reducing van der Waals forces between 2D-TMDs avoiding agglomeration and precipitation. From this perspective, we review the recent advances in improving the detection of biomolecules, heavy metals, and gases using chemically functionalized 2D-TMDs. Covalent and non-covalent functionalized 2D-TMDs are commonly used for the detection of biomolecules and metals, while 2D-TMDs functionalized with metal nanoparticles are used for gas and Raman sensors. Finally, we describe the limitations and further strategies that might pave the way for miniaturized, flexible, smart, and low-cost sensing devices. Full article

(This article belongs to the Special Issue Chemical Sensors—Recent Advances and Future Challenges 2023–2024)

► Show Figures

Figure 1

Journal Menu

Journal Browser

Chemical Sensors—Recent Advances and Future Challenges 2023–2024

Share This Special Issue

Special Issue Editor

Special Issue Information

Benefits of Publishing in a Special Issue

Published Papers (9 papers)

Research

Review

Other

Further Information

Guidelines

MDPI Initiatives

Follow MDPI