Geomatics, Volume 6, Issue 2 (April 2026) – 18 articles

Satellite-derived bathymetry (SDB) offers a practical alternative for mapping shallow reefs in remote oceanic settings where acoustic surveys are costly and logistically constrained. Here we benchmark PlanetScope 8-band (3 m) surface reflectance—an underused commercial constellation for reef SDB—using ICESat-2 Advanced Topographic Laser Altimeter System (ATLAS) ATL03 photon data (Release 006) as independent vertical control. Seventeen ATL03 ground tracks (2019–2025) were processed using geometric filtering, photon classification, and explicit air–water refraction correction. This yielded 5171 candidate seafloor observations, of which 5021 were co-located with valid PlanetScope water pixels after Usable Data Mask screening (UDM2/UDM2.1), sun-glint correction, and reflectance quality screening. Four SDB formulations (Lyzenga, Bierwirth, and Stumpf) were calibrated and independently validated using depth-stratified train/validation partitions (70/30, 80/20, and 90/10). Across partitions, the multiband polynomial model of Lyzenga 2006 generalized best (R² = 0.843–0.859; RMSE = 1.734–1.813 m; bias = −0.070 to −0.081 m), followed by Bierwirth (R² = 0.826–0.845; RMSE = 1.818–1.904 m). Lyzenga 1985 reported lower skill (RMSE ≈ 3.1 m), while the Stumpf log-ratio failed in independent validation. ICESat-2 photon bathymetry provides repeatable point-based control in clear waters but remains less precise than echo sounding due to photon classification and spatial-support effects; therefore, uncertainties and applicability limits must be reported. Overall, PlanetScope 3 m, 8-band surface reflectance supports reproducible reef-scale SDB in Seaflower under the evaluated conditions, with Lyzenga 2006 as a robust baseline. Full article

This study applies Small Baseline Subset Interferometric Synthetic Aperture Radar (SBAS-InSAR) to investigate surface deformation dynamics in the hyper-arid Eastern Province of Saudi Arabia, with emphasis on quantifying sand dune migration and identifying areas susceptible to wind erosion. Utilizing Sentinel-1 SAR data and the MintPy toolbox, ground deformation was quantified with millimeter-scale precision. Results reveal significant subsidence, up to 15 cm/year in landfills, linked to waste compaction and groundwater depletion. Localized uplift of ~4 cm/year on northern peripheries is directly attributed to aeolian sand accumulation from seasonal Shamal winds, providing quantitative evidence of dune migration. While direct measurement of wind erosion (net deflation) remains challenging due to the dominance of depositional signals and the spatial heterogeneity of erosion processes, areas of potential erosion are inferred from negative displacement patterns outside landfill zones and from coherence characteristics indicative of surface instability. The integration of SBAS-InSAR with GPS and ERA5 wind reanalysis resolves the combined influence of aeolian deposition, hydrogeological changes, and anthropogenic activity, offering insights into both components of aeolian dynamics and a replicable model for sustainable land management in arid environments. Full article

Atmospheric refractivity governs the propagation behavior of electromagnetic waves in the lower troposphere. Accurate spatial characterization of this parameter is essential for optimizing communication, radar, and navigation systems. This study presents a geostatistical framework for generating high-resolution refractivity maps using Universal Kriging (UK) applied to meteorological observations from a dense network of automatic weather stations in the Galician region (NW Spain). The methodology explicitly models the non-stationary vertical structure of the atmosphere by decomposing the refractivity field into a deterministic altitude-dependent drift and a stochastic residual component characterized by an exponential variogram. Validation, performed using independent test stations bounding the regional vertical profile, demonstrates that the UK approach significantly outperforms Ordinary Kriging (OK). UK not only reduces mean errors and improves linear agreement, but critically minimizes systematic bias and extreme outlier occurrences ($P_{95}$). Beyond accurate spatial interpolation, the dynamically estimated vertical drift retrieves the macroscopic refractivity gradient, serving as a direct, real-time diagnostic tool to classify anomalous radio-frequency (RF) propagation regimes (e.g., super-refraction and ducting) and supporting robust decision-making in complex topographies. Full article

This study evaluates the rooftop solar photovoltaic (PV) potential at the building level in the tourism-rich districts of Northern Khyber Pakhtunkhwa (KPK), Pakistan, using advanced geospatial analysis to support renewable energy planning. By combining the Area Solar Radiation tool with detailed building footprint data, the study identified solar energy potential and prioritized areas for PV system installations. Results show that approximately 35% of the 1.29 million buildings analyzed are suitable for solar panels, with energy generation capacity varying by building size and district. Spatial analysis further highlighted Union Councils (UCs) where over 50% of buildings are solar-suitable, enabling precise targeting of renewable energy initiatives. The study underscores the importance of integrating local geographical and socio-economic data to enhance the feasibility and scalability of solar energy solutions in rural and urban settings and can be used to guide policy prioritization and funding decisions. This research demonstrates how geospatial analysis and open data can drive localized clean energy adoption, directly contributing to Sustainable Development Goal 7 by advancing affordable and sustainable energy solutions. Full article

Accurate identification of road network intersections is essential for urban planning, autonomous navigation, and traffic safety analysis. However, standard approaches relying on local geometric attributes often overlook essential topological information. This limitation is particularly problematic for intersection types that are locally similar but topologically distinct. To address this, we propose a hybrid framework that augments intrinsic node attributes with Generalized Random Dot Product Graph embeddings and neighbor-aggregated features. We utilize tree-based ensemble classifiers, specifically Random Forest and Extreme Gradient Boosting, to process this enriched feature set. Unlike standard spectral methods that assume homophily, this approach explicitly models heterophilous connectivity to capture structural patterns where dissimilar nodes connect. Experiments on a real-world urban road network demonstrate that this topological augmentation yields consistent and robust improvements. The proposed integration with the Extreme Gradient Boosting model achieves a Macro ROC AUC of 0.8966 and a Micro F1 score of 0.7005, outperforming the baseline model (ROC AUC 0.8100, Micro F1 0.5919). Performance gains are most pronounced for topologically ambiguous intersection classes, confirming that local attributes alone fail to capture structural distinctions. These results demonstrate that latent structural context is a critical discriminator for granular road intersection classification. Full article

This research addresses the increasing demand for low-cost GNSS solutions in natural resources management and geodesy by comparing a dual-frequency RTK receiver and a single-frequency autonomous receiver under identical conditions. The novelty lies in the simultaneous testing of u-blox ZED-F9P and u-blox MAX-M10S receivers connected to a common antenna, eliminating different signal reception effects. The study also evaluates the horizontal accuracy and area determination accuracy and the influence of seasonal foliage. Experiments were conducted on three polygons with varying vegetation canopies during leaf-on and leaf-off periods. The ZED-F9P receiver demonstrated high accuracy and stability when using RTK corrections. Under canopy conditions, the average horizontal errors were 0.17–0.18 m during leaf-on and improved by 58% to approximately 0.07 m during leaf-off season. The average area determination errors remained below 2%, confirming its suitability for precise mapping. In contrast, the MAX-M10S receiver showed substantial variability under vegetation. Its average horizontal errors reached 1.5–3.0 m during leaf-on season, with the maximum errors exceeding 5 m. Its seasonal improvement ranged from 41 to 54%, while its area errors reached up to 14.7%. The study confirms that while vegetation cover and seasonal foliage are limiting factors for both types of devices, low-cost RTK receivers represent a viable alternative to expensive professional instruments, even in more challenging conditions. Full article

Monitoring forest density is essential for understanding ecosystem health, wildfire risk, and post-disturbance recovery. This study proposes a robust methodology to extract forest density classes exclusively using Sentinel-2 multispectral imagery combined with vegetation indices (VIs), textural parameters, and spatial clustering metrics. The approach was applied to the northern part of Euboea Island, Greece, as a pilot area severely affected by a wildfire in August 2021. Four cloud-free Sentinel-2 images (2017–2024) were selected to capture pre- and post-fire conditions. A set of nine VIs—representing vegetation vigor, chlorophyll content, soil exposure, and canopy moisture—were calculated and statistically assessed for independence. To enhance classification accuracy, texture measures (homogeneity, correlation, and entropy) and spatial autocorrelation metrics (Moran’s I, Getis-Ord Gi) were derived for selected VIs. Supervised classification was performed using the Maximum Likelihood algorithm, yielding overall accuracies up to 89.4% and kappa coefficients above 0.85 when combining VIs with texture and spatial metrics. Results revealed a dramatic 49.3% reduction in forest cover immediately after the wildfire, with partial recovery (to 77.9% of pre-fire levels) three years later, mainly as a low-density forest. Approximately 12.1% of forest cover failed to regenerate, indicating potential long-term ecosystem degradation. The proposed approach provides a computationally efficient, high-accuracy alternative to data-fusion methods involving (Light Detection and Ranging) LiDAR or (Synthetic Aperture Radar) SAR datasets, making it suitable for operational forest monitoring and fire-risk management. Full article

Post-mining surface uplift has affected the northeastern part of Pécs, Hungary, since the closure of underground coal mines in the 1990s. This study synthesises 30 years of SAR data (ERS, Envisat, and Sentinel-1) with geodetic surveys, groundwater monitoring, and over 900 residential damage reports to investigate the spatiotemporal evolution of this deformation. In densely built urban environments, Persistent Scatterer Interferometry (PS-InSAR) provides spatially detailed complementary data measurements to traditional levelling, particularly where survey lines offer limited coverage. The performed combined analysis tracked deformation from initial uplift through stabilisation, revealing a clear transition: while early lower-order measurements showed limited correlation, modern Sentinel-1 data and high-order geodetic surveys (post-2014) demonstrate a robust correlation (R = 0.65). The cross-correlation of InSAR results with geodetic and hydrogeological records revealed that aquifer recovery by the 2010s coincided with the onset of surface stability. While over 90% of 1990s residential damage claims fell within measured deformation zones, this relationship weakened over time, with recent claims showing little spatial connection with ground movements. This highlights the complementary strengths of InSAR and geodetic techniques. It demonstrates the value of integrating geotechnical and socio-economic datasets, providing a transferable framework for reliable deformation monitoring and risk management in post-mining urban environments. Full article

Archaeological sites characterized by the coexistence of extensive above-ground terrain and hypogeum structures present major challenges for accurate and comprehensive geospatial documentation. Conventional survey approaches—such as static terrestrial laser scanning (TLS), total-station measurements, and aerial photogrammetry—often suffer from operational constraints, particularly in the presence of narrow underground spaces, low or absent illumination, harsh environmental conditions, and restrictions on UAV deployment. Additional complexity arises when both surface and subterranean elements must be consistently georeferenced to a common global reference system, especially where establishing a traditional topographic–geodetic control network is impractical. Within the framework of the EIMAWA Egyptian–Italian Mission conducted by the University of Milano since 2018, the Geomatics group of the University of Bologna designed and implemented a multi-scale multi-technique 3D documentation workflow, with a prominent role assumed by Simultaneous Localization and Mapping (SLAM) mobile laser scanning. The approach was supported by GNSS measurements providing centimetric accuracy. SLAM was employed to document both the surface necropolis and multiple hypogeal tombs, enabling rapid acquisition of dense three-dimensional data in environments where traditional techniques are limited. All datasets were integrated within a unified reference system, resulting in a coherent, multi-layered spatial dataset representing both landscape and underground spaces. The results demonstrate that SLAM can produce dense point clouds that document at few-centimetric level accuracy and continuously both above- and below-ground contexts. Quantitative analyses of the co-registration and mutual alignment of multiple SLAM datasets confirm a high degree of internal consistency, further enhanced through post-processing refinement. Overall, the experience indicates that this solution represents a practical and reliable technique for complex archaeological surveying. Full article

This work presents a simulation-based approach to support the planning of Terrestrial Laser Scanning (TLS) surveys for landslide monitoring. Starting from an approximate digital model of the slope, the method estimates the spatial distribution of positional error induced by scanner characteristics, laser beam divergence and, critically, by the incidence angle between the laser beam and the local surface normal. Because complex morphologies cause rapid local variations in incidence angle, neighbouring points may exhibit markedly different error magnitudes, making a direct classification of raw error values insufficient to delineate homogeneous areas. To address this, a multidimensional variable is defined for each simulated point, combining position, estimated error, distance from the scanner and incidence angle. After dimensionality reduction through PCA, the dataset is clustered using K-means with a sufficiently large number of clusters to preserve spatial resolution. Each cluster is associated with a representative error level, and clusters are then merged into broader error classes that delineate zones of comparable expected precision. The procedure is repeated for alternative scanner positions, enabling a comparative evaluation of achievable accuracy across the slope and the identification of areas requiring multiple scans. The method provides a quantitative, reproducible framework to guide TLS station selection and optimize survey design in complex morphological settings. Full article

Tropical cyclones rank among the most destructive natural hazards globally, posing significant threats to coastal ecosystems and communities. Mangrove forests, renowned for their ecological importance and coastal protection services, are vulnerable to these disturbances, suffering structural damage, habitat loss, and disruption of vital ecosystem functions. Conventional field-based assessment methods often fall short in capturing the rapid and widespread impacts of cyclones, particularly in remote or cloud-obscured regions. This review aims to provide a comprehensive synthesis of remote sensing applications for monitoring cyclone-induced impacts on mangrove and coastal ecosystems worldwide. Through a systematic literature review of 74 peer-reviewed articles from 1990 to 2025, the study evaluates the utility of optical sensors, radar systems, and multi-sensor platforms in assessing inundation, vegetation damage, and ecosystem service loss. Key methodological advances such as time-series analysis, machine learning, and UAV-based validation are highlighted, alongside critical gaps including limited geographic coverage, weak validation practices, and minimal socio-economic integration. Notably, 75.4% of reviewed studies are concentrated in Asia, with Bangladesh and India alone accounting for 44.6% of the total literature, underscoring a pronounced geographic bias. The findings underscore the need for robust, near-real-time monitoring frameworks that combine satellite technologies with ground data and community engagement. Ultimately, the review advocates for an integrated, multi-sensor, and participatory approach to cyclone resilience, offering valuable insights for future research, disaster response planning, and sustainable mangrove management. Full article

Wildfires have become more frequent and intense worldwide due to climate change and anthropogenic activities, which is why accurate and timely burned area mapping is essential for estimating damage and effective post-fire recovery planning. Synthetic Aperture Radar (SAR) data, which operates under all weather conditions and day-night cycles, offers a reliable source for burned area mapping. In this context, several studies have explored the use of dual-polarization SAR imagery and machine learning, yet the influence of multi-date, dual-orbit pass data and texture features remained unexplored. Therefore, this study aims to assess the Sentinel-1 acquisition configurations, varying in temporal depth and orbital direction, for wildfire burned area mapping, considering the recent Palisades wildfire event as a study area. A comparative study was conducted across different scenarios to evaluate the effectiveness of using single-date versus multi-date SAR imagery, the integration of ascending and descending orbit passes, and the contribution of Grey-Level Co-occurrence Matrix texture features. The performance of Random Forest (RF) and Extreme Gradient Boosting classifiers was analyzed through the scenarios mentioned above. The single-date configuration using RF achieved an accuracy of 82.34%, F1-score of 81.43%, precision of 83.07%, recall of 80.84%, and ROC-AUC of 90.88%, whereas the multi-date approach reached 85.78%, 85.15%, 86.45%, 84.56%, and 93.28%, respectively. Our study highlights the importance of acquisition configuration and texture information for reliable SAR-based wildfire burned area assessment. Full article

Climate change is a critical global challenge, and the building sector accounts for nearly 30% of global greenhouse gas (GHG) emissions, remaining a key target for mitigation. Indoor environments contribute significantly to GHG emissions, primarily through heating, cooling, lighting, and occupant-driven energy use. Indoor mapping, serving as the foundation for Digital Twins (DTs), provides a spatiotemporal framework that integrates sensor data with Building Information Modelling (BIM), Geographic Information Systems (GIS), and Internet of Things (IoT) to support energy-efficient, low-carbon building operations. This review examined the role of indoor mapping in understanding, modelling, and reducing GHG emissions in buildings. It synthesized current advancements in indoor spatial data acquisition, ranging from Light Detection And Ranging (LiDAR) and Simultaneous Localization and Mapping (SLAM) to deep learning-based floor plan extraction, and evaluated their contribution to improved indoor environmental analysis. The review highlighted emerging techniques, challenges, and gaps, particularly the limited integration of physical indoor spaces with virtual layers representing assets, occupants, and equipment. Addressing this gap requires embedding spatial modelling as an intermediate analytical layer that structures and contextualizes sensor data to support spatiotemporal decision-making. Overall, this review demonstrated that indoor mapping plays a critical role in transforming spatial information into actionable insights, enabling more accurate energy modelling, enhanced real-time building management, and stronger data-driven strategies for GHG mitigation in the built environment. Full article

Geological hazard data exhibits high-volume and multi-type characteristics, specifically characterized by inherent complexity; measurement uncertainty; cross-source heterogeneity; underdeveloped semantic organization; and fragile inter-entity associations. Consequently, advanced modeling techniques coupled with robust extraction frameworks become imperative for effective unstructured data governance. To address this challenge, we propose a content–knowledge representation framework that decomposes and reconstructs disaster data using fine-grained content entities as base units. This approach allows for a unified description, objectification, ordering, hierarchical storage, and indexed categorization of unstructured information. Furthermore, we develop specialized text extraction algorithms tailored to document imagery and vector maps—facilitating the systematic application of information retrieval techniques while efficiently targeting specific thematic content. Our method outperforms two representative deep learning architectures (Fast CNN and FCN), demonstrating superior performance in segmenting target regions and precisely detecting textual elements, tables, and geographic features within complex datasets. By studying the modeling and extraction technology of unstructured geologic data, this paper establishes the value chain of geologic result data, which can provide strong support for digital management of geologic disaster data and improve work efficiency. Full article

The GCOM-C satellite possesses optimal wavelength bands around 530 nm and 570 nm for monitoring seasonal variations in the photochemical reflectance index (PRI) and chlorophyll–carotenoid index (CCI), which are sensitive to carotenoid contents and its ratio to chlorophyll contents, respectively. As well as NDVI, these indices are excellent indicators for monitoring pigment contents of evergreen trees in winter, which are considered susceptible to climate change impacts. In this study, to investigate the characteristics and usefulness of the GCOM-C-derived indices, the seasonal variations in these indices were analyzed between 2018 and 2024 at two evergreen forest sites in Japan, and compared to CCI and NDVI derived from MODIS, which also has a band near 530 nm. The satellite observation results show that the decreases in all indices for both satellites in winter were observed in the order of PRI, CCI, NDVI. This is thought to indicate that carotenoid contents increased in response to the decrease in land surface temperature to mitigate low-temperature stress, followed by a delayed decrease in chlorophyll contents. GCOM-C showed 0.1 larger NDVI values and 0.2 larger CCI values than MODIS, and the difference was estimated to be largely influenced by the disparity in sensor sensitivity in the red bands. The dispersion of each index was reduced by using data with small sensor zenith angles (below 20 degrees for GCOM-C and 0 to 30 degrees for MODIS); however, MODIS showed a decline in observation accuracy due to satellite drifting in 2024. Spectral measurements of leaves collected at the site also showed similar VI decreases; however, the satellite-derived CCI were 0.12 lower, suggesting that reflection from dead leaves influences the satellite data. This study confirmed that GCOM-C, which can measure both PRI and CCI with high spatial resolution, is suitable for observing seasonal variations in carotenoid and chlorophyll contents in evergreen forests. Full article

Mobile phone usage data inherently involve many spatial elements; therefore, gathering extensive individual mobile phone records can offer unique insights into human spatial behavior at both personal and societal levels. This study contributes to travel behavior research by examining group-level human mobility obtained from millions of Hungarian mobile phone records. After developing mobility metrics from georeferenced cellular data, we applied a computationally efficient two- and three-dimensional Fuzzy C-Means (FCM) unsupervised clustering algorithm to identify groups of people with similar behavioral traits. The resulting membership probabilities—based on combinations of mobility metrics and user attributes—indicated that high travel distances or higher equipment prices could lead to a clear separation in travel behavior, while complex mobility patterns appeared less influenced by human factors such as age. Furthermore, even though the fuzzy outcomes offer probabilistic rather than exact group assignments, the generated maps revealed distinct, non-random spatial patterns. Full article

Floods represent one of the most frequent and damaging natural hazards in Mediterranean mountain regions, where intense rainfall and complex topography amplify runoff and inundation risk. This study aims to delineate flood-susceptible zones in the Monti Lucretili area of central Italy, an environmentally sensitive and culturally significant landscape that hosts archeological remains and UNESCO listed dry-stone heritage using an integrated Analytical Hierarchy Process (AHP) and Geographic Information System (GIS) approach. Fifteen (15) conditioning factors, including elevation, slope, rainfall, soil, lithology, land use/land cover, drainage density, and proximity to rivers and roads, were derived from open-access satellite remote sensing and spatial datasets. The AHP model produced a flood susceptibility index ranging from 1.806 to 4.465, reclassified into five categories from very low to very high zones. The resulting map indicates that low- and moderate-susceptibility zones dominate the study area, while high and very high classes are primarily concentrated along valleys and drainage corridors. Model validation indicates strong regional-scale predictive performance, with 85.36% of modeled flood-prone areas located within high- to very-high-susceptibility zones and an AUC value of 0.82. Overall, the study highlights the potential of open-access AHP–GIS modeling as a practical screening tool for flood susceptibility assessment and heritage-aware spatial planning in Mediterranean environments. Full article

Olive groves are an important agricultural component in the Mediterranean region that offers various ecological benefits. The olive tree has tremendous cultural and economic value and is cultivated over a wide geographical range. It is essential to actively implement innovative agricultural practices to achieve efficient, sustainable olive cultivation. Automatic tree identification in olive groves is an essential tool for applications such as tree health monitoring and yield estimation. Deep learning-based approaches, which have recently gained prominence, hold significant potential for this purpose. However, the large amount of training data required by deep learning methods increases their time and effort costs. Data augmentation methods have been developed to solve this problem. In this study, olive tree detection and segmentation from unmanned aerial vehicle (UAV) images were performed using current You Only Look Once (YOLO) architectures (YOLOv8, YOLOv10, YOLOv11, YOLOv12) and transformer-based object detection algorithms (Real-Time DEtection TRansformer (RT-DETR) and Roboflow-DEtection Transformer (RF-DETR)). Two different datasets, one of which was a new dataset generated within the scope of this study, were used in this study. To investigate the effect of data augmentation on algorithm performance, both the original datasets and the augmented datasets were used. As a result of the study, 0.987 mAP was obtained with YOLOv11n, YOLOv11s, and YOLOv12s on the Olive Tree Detection (OTD) dataset, while 0.884 mAP was obtained with YOLOv8l and YOLOV8x on the Yalova dataset. Full article