Skip to Content
SustainabilitySustainability
  • Article
  • Open Access

10 January 2026

24 Pages

Experimental 3E Assessment of a PLC-Controlled Solar Air Heater with Adjustable Baffle

Department of Energy Systems Engineering, Hasan Ferdi Turgutlu Faculty of Technology, Manisa Celal Bayar University, Acarlar District, Şehit Ali Karakuzu Street No:10, 45400 Turgutlu, Manisa, Türkiye

Abstract

This study presents an experimental 3E (energy–exergy–environmental) assessment of a PLC-controlled solar air heater (SAH) equipped with adjustable internal baffles. Unlike conventional passive systems, the proposed design enables active airflow regulation to maintain stable outlet temperatures of 54 °C and 60 °C, achieving rapid stabilization within 3–10 s under outdoor conditions. Experimental results show that increasing the baffle inclination significantly enhances convective heat transfer and thermal efficiency, while the friction factor remains primarily governed by the Reynolds number and exhibits minimal sensitivity to baffle angle. Exergy efficiency values remain relatively low (1.24–2.69%), and the sustainability index stays close to unity, reflecting the inherent thermodynamic limitations of low-temperature solar air heaters rather than deficiencies in system design. A regression-based airflow velocity model is developed to support fan-speed optimization and to clarify the trade-off between thermal enhancement and auxiliary power demand. Long-term projections based on regional solar data indicate that the proposed SAH can deliver approximately 20–22 MWh of useful heat and mitigate nearly 9 tons of CO2 emissions over a 20-year operational lifetime. Overall, the results demonstrate that PLC-assisted dynamic baffle control provides a flexible and effective approach for improving the performance and operational stability of solar air heaters for low-temperature drying applications.

1. Introduction

Solar energy plays a central role in sustainable energy transitions due to its high availability and low environmental impact. Solar air heaters (SAHs), widely used in low-temperature applications such as space heating, agricultural drying [1], and sludge treatment [2], have attracted increasing interest because of their simple design, low cost, and operational safety. An SAH transfers absorbed solar radiation to an air stream by natural or forced convection; however, the inherently low convective heat transfer coefficient between the absorber surface and air limits overall thermal performance. In addition, the low density and heat capacity of air require relatively high mass flow rates, while the low power density of solar energy (approximately 1 kW m−2) [3] necessitates larger collector areas. These constraints underline the importance of optimizing airflow behavior and enhancing heat transfer within the air channel.
To address these limitations, a wide range of geometric modifications have been proposed to intensify turbulence and improve heat transfer performance. These include grooved absorber surfaces [4], horizontal barriers [5], fins [6], various baffle arrangements [7], and roughened absorber plates such as wire-roughened [8] and corrugated configurations [9]. Several recent studies and reviews have confirmed the effectiveness of such enhancements and identified suitable rib and roughness geometries for performance improvement [10,11,12,13]. Other investigations have examined the influence of baffle length [14], baffle configuration [15], and combined vane–baffle structures [16] on thermo-hydraulic behavior. A recent comprehensive review further emphasized that while internal geometric optimization is critical for maximizing thermal performance, heat transfer enhancement must be carefully balanced against pressure drop penalties to ensure practical applicability [17].
Despite these advances, most SAHs still operate under passive conditions and employ fixed internal geometries that cannot respond to variations in solar irradiance, ambient temperature, or thermal demand. Existing studies often focus either on thermo-hydraulic parameters such as Reynolds number, Nusselt number, and pressure drop [18,19,20], or on energy–exergy–sustainability indicators [21,22,23], typically treating these aspects independently. Multi-criteria optimization techniques, including Taguchi, TOPSIS, and Grey–Taguchi methods [24,25,26], provide valuable offline design guidance but do not enable adaptive operation under real outdoor conditions. More recent microcontroller-based implementations have introduced limited automation capabilities [27,28,29]; however, these systems generally lack mechanisms for actively influencing the internal flow structure or achieving reliable outlet air temperature regulation.
Recent studies on other types of solar heating systems have further highlighted the importance of controllability and temperature stabilization. For instance, smart-switchable cover-assisted finned solar air collectors have been numerically investigated to maintain nearly constant outlet air temperatures under variable solar conditions [30], while wavy corrugated solar air collectors integrated with thermal energy storage and data-driven modeling approaches have demonstrated enhanced thermal performance and operational stability [31]. These studies illustrate a growing research trend toward adaptive and control-oriented solar thermal systems, while also indicating that internal flow management remains a largely underexplored control variable in experimental SAHs.
From this perspective, a clear research gap emerges: experimental studies that systematically investigate baffle-angle-based flow guidance, combined with active airflow regulation and integrated thermal–energy–exergy–sustainability assessment within a single SAH system, remain scarce. Such capabilities are particularly important for applications requiring stable and controllable outlet air temperatures, including agricultural drying, HVAC preheating, and low-temperature industrial processes.
To address this gap, the present study experimentally investigates a PLC-assisted solar air heater equipped with fixed rectangular baffle plates whose inclination angles can be mechanically adjusted to guide the internal airflow. In the proposed system, the baffle geometry itself remains unchanged; however, the baffle angles are varied to modify the flow structure and mixing characteristics within the air channel. A programmable logic controller (PLC) dynamically adjusts the air velocity, within predefined operational limits, to achieve target outlet air temperatures representative of drying applications (54 °C and 60 °C). Forced convection is deliberately employed to ensure stable, controllable, and repeatable operating conditions, which are essential for reliable comparison of different baffle configurations.
The system performance under each baffle configuration is evaluated using a comprehensive 3E performance framework, including thermal (energy efficiency), thermodynamic (exergy efficiency), and environmental–economic sustainability indicators such as the Sustainability index (SI), CO2 mitigation potential, and payback period. The primary objective of this study is not to introduce a new control architecture, but to provide a systematic experimental assessment of baffle-angle-induced flow guidance combined with PLC-regulated airflow adjustment under outdoor conditions, thereby clarifying its potential to enhance temperature stability, operational flexibility, and overall thermo-hydraulic performance compared with conventional passive SAH configurations.

2. Materials and Methods

2.1. Experimental Setup

The experimental solar air heater (SAH) was constructed from 1 mm galvanized steel with overall dimensions of 2250 × 940 × 200 mm. The front cover consisted of heat-resistant tempered glass with an average solar transmittance of 0.90, while the absorber plate was fabricated from 4 mm matte black aluminum with a measured absorptivity of approximately 0.95. The general geometry of the collector and the locations of the adjustable baffles are shown in Figure 1. A detailed view of the adjustable baffle mechanism is provided in Figure S1 (Supplementary Materials).
Figure 1. Overall geometry and dimensional layout of the solar air heater, including adjustable baffle placement.
The collector contains ten rectangular aluminum baffles installed along the airflow path. Each baffle has fixed dimensions (275 mm × 50 mm × 30 mm), while its inclination angle can be mechanically adjusted to control the internal airflow. To ensure airtightness and mechanical stability, an internal O-ring seal is placed between the collector casing and the rotating shaft, and each shaft is supported by an external bearing with an O-ring-covered housing to maintain alignment and enable smooth rotation, as shown in Figure 2a (Section A-A).
Figure 2. Mechanical engineering details: (a) Shaft sealing and bearing cross-section (Section A-A), (b) Belt-pulley motion mechanism.
The rotational motion of the baffles was transmitted through a synchronous belt–pulley system driven by a DC motor coupled with a reducer unit, ensuring simultaneous movement of all baffles between 0° and 90° (Figure 2b). Manufacturing tolerances were carefully controlled to maintain flow uniformity within the channel. The longitudinal spacing between baffle rows was set to 300.00 ± 0.50 mm, while the lateral distance between the shafts was maintained at 600.00 ± 0.50 mm. These tolerances were selected to limit geometric asymmetry that could otherwise introduce undesired local flow disturbances. Further details of the motor–shaft assembly are provided in Figure S2 (Supplementary Materials).
Changing the baffle inclination angles modifies the flow resistance and mixing characteristics within the air channel, thereby influencing the heat transfer behavior. In this study, the baffle inclination angles were set to 0°, 15°, 30°, 45°, 60°, 75°, and 90° with respect to the airflow direction, and each angle configuration was treated as a distinct experimental condition. The airflow direction and the working principle of the baffle angle adjustment mechanism are schematically illustrated in Figure 3. The internal height of the collector is 200 mm, of which the lower 130 mm accommodates the absorber plate and rotating shaft assembly, while the upper 70 mm forms the primary airflow passage. All lateral surfaces were insulated with glass wool to minimize conductive heat losses.
Figure 3. Schematic representation of airflow direction and baffle rotation mechanism at a 45° inclination.
Forced convection was provided by a 100 mm axial fan located at the outlet of the collector, creating negative pressure at the inlet and ensuring stable airflow through the system. Air temperatures at the inlet, mid-section, and outlet were measured using calibrated PT100 resistance temperature detectors. All sensor signals were continuously transmitted to a Mitsubishi PLC for real-time monitoring and control. The pump and hydraulic system employed in the experimental setup are illustrated in Figure S3 (Supplementary Materials).
While the baffle inclination angles were set to predefined experimental configurations using servo motors, the PLC dynamically regulated the fan speed to achieve target outlet air temperatures. A PID control strategy was implemented, with controller parameters determined experimentally to ensure stable operation without excessive oscillations ( K P = 2.0 , K i = 0.12 ,     K d = 0.050 ). To limit overshoot and prevent integral windup, a hysteresis band of ±0.5 °C was defined around the temperature setpoint. In addition, a soft-start ramp function was applied to the fan motor driver, ensuring smooth speed transitions and limiting transient overshoot to below 3%.
The control logic was implemented using a ladder diagram algorithm based on real-time temperature feedback. A Delta HMI panel was employed to monitor instantaneous operating parameters, including baffle position, airflow temperatures, and fan speed. Furthermore, a custom SCADA interface was developed to enable detailed visualization of system behavior and manual configuration of baffle angles. The PLC control interface and the corresponding program flow are shown in Figure S4 (Supplementary Materials).

2.2. Outdoor Performance Evaluation Conditions

The experimental setup described in the previous section was subjected to outdoor performance tests conducted between 9 and 29 August 2023. The experimental solar air heater was installed on the faculty terrace, ensuring unobstructed solar exposure throughout the test period. A photographic view of the experimental rig under outdoor operating conditions is presented in Figure 4, which illustrates the collector orientation, installation height, and surrounding environment during the performance tests. Additional photographic views of the experimental setup from the front, side, and rear perspectives are provided in Figure S5.
Figure 4. Outdoor installation of the experimental solar air heater on the faculty terrace.
This testing period coincides with the peak agricultural drying season in the region, during which high and relatively stable thermal loads are commonly encountered. All experiments were conducted exclusively on clear-sky days between 10:00 and 16:00, corresponding to periods of maximum solar availability. During the experimental campaign, the average global solar irradiance was measured as 850 ± 25 W/m2, while ambient air temperatures ranged between 41 and 45 °C. Wind speeds remained relatively low during the test periods, contributing to stable and repeatable outdoor operating conditions.
It should be emphasized that the scope of this study was intentionally restricted to high-irradiance summer conditions in order to evaluate the system under peak thermal load scenarios. While this controlled outdoor environment enhances the internal consistency of the experimental results, it also limits their broader generalizability. Accordingly, the reported thermal, exergy, and sustainability performance indicators are representative of clear-sky, high-irradiance operating conditions, and system behavior may differ under low-irradiance, cloudy, or winter conditions.
Prior to each data acquisition period, the system was operated continuously for 15–20 min to ensure that steady-state conditions were established. Data were recorded only after the outlet air temperature and airflow rate exhibited stable behavior within the predefined control tolerance bands. Therefore, the findings presented in this study should be interpreted as reflecting summer peak-performance characteristics, rather than year-round operational behavior.

2.3. Dynamic Response and Control Strategy

The dynamic behavior of the PLC-assisted control system was evaluated by applying step changes to the predefined baffle inclination angles. Changes in baffle angle modify the internal flow resistance and mixing characteristics, which in turn affect the heat transfer rate and the outlet air temperature.
For each experimental configuration, the baffle angles were set mechanically to the desired position prior to data acquisition. When a new temperature setpoint was applied, the PLC continuously received real-time outlet air temperature feedback and adjusted the fan speed only, in order to regulate the airflow rate and achieve the target outlet temperature. The baffle angles themselves were not modified dynamically by the PLC during operation.
A delay of approximately 3 s was observed between the application of a new control command and the onset of fan speed adjustment. This delay is attributed to the PLC scan cycle and the response time of the fan driver. Following the adjustment, the outlet air temperature converged to the target value within approximately 10 s, stabilizing within a ±0.5 °C tolerance band. No significant temperature overshoot was observed, with transient deviations remaining below 3%, indicating appropriate controller tuning.
Time-dependent data extracted from the HMI indicated a temporal measurement uncertainty of ±0.5 s. Overall, these results demonstrate that the proposed control architecture provides rapid and stable thermal regulation, typically achieving convergence within 3–10 s after a change in baffle angle configuration, thereby ensuring reliable operation under outdoor conditions.

2.4. Experimental Procedure

Two target outlet air temperatures, 54 °C and 60 °C, were selected for the experimental analysis due to their widespread use in solar-assisted agricultural drying applications and low-temperature thermal processes. The primary objective of the experimental procedure was to evaluate the system’s ability to maintain a stable thermal output under different internal flow configurations.
The experimental matrix consisted of seven discrete baffle inclination angles, namely 0°, 15°, 30°, 45°, 60°, 75°, and 90°. For each angular configuration, the baffle inclination angle was mechanically set to the desired position prior to data acquisition and kept constant throughout the test. During operation, the PLC dynamically regulated the fan speed only, based on real-time outlet air temperature feedback, in order to achieve and maintain the specified temperature setpoint.
This control approach enabled a consistent comparison of different baffle angle configurations under identical thermal targets, while avoiding geometric changes during steady operation. Tests were conducted under consistent outdoor environmental conditions, as described in Section 2.2, to ensure the reliability and comparability of the experimental results.
The collector was characterized by a relative roughness ratio (e/Dh) of 0.0397 and a pitch-to-height ratio ( p / e ) of 9.17, both of which fall within the recommended ranges for artificially roughened solar air heater ducts. The overall instrumentation layout, including the locations of the PT100 temperature sensors, the airflow measurement section, and the servo-driven baffle angle adjustment mechanism, is illustrated in Figure 5. The collector cross-section and the detailed measurement layout are additionally presented in Figure S6 (Supplementary Materials).
Figure 5. Experimental measurement points: (a) temperature sensing locations and servo driven baffle mechanism, (b) flow rate measurement point at the collector outlet.

2.5. Instrumentation and Measurement Accuracy

All measured parameters were used to evaluate the thermal (energy), exergy, and sustainability-related performance indicators of the solar air heater under each baffle inclination configuration. Air velocity at the inlet was measured using a Testo 440 dP hot-wire anemometer, positioned 20 mm upstream of the inlet opening to reduce flow disturbance effects. The measured air velocity was used to calculate the mass flow rate and associated thermo-hydraulic parameters.
Inlet and outlet air temperatures were measured using PT100 resistance temperature detectors (Emko RTKR M06 L050.1; Air temperatures were measured using a PT100 resistance temperature detector (model RTKR-M06-L050.1, EMKO Elektronik A.Ş., Istanbul, Türkiye) integrated into the PLC-based data acquisition system. The surface temperature distribution of the absorber plate was monitored using a FLIR thermal camera (model 62101-0101; Thermal imaging measurements were performed using a FLIR T420 high-resolution infrared thermal camera (model 62101-0101, FLIR Systems, Boston, MA, USA), with a 320 × 240 pixel detector resolution) to qualitatively assess temperature uniformity during operation.
Global solar irradiance was measured using a calibrated pyranometer with an accuracy of ±2%, mounted parallel to the collector glazing to ensure consistent measurement of incident radiation. Ambient air temperature and relative humidity were monitored using a digital thermo hygrometer positioned in the vicinity of the experimental platform, shielded from direct solar exposure.
All sensors were connected to the PLC-based data logging system, which recorded measurements at 5 s intervals throughout the experiments. A comprehensive summary of the measurement instruments, their operating ranges, and associated uncertainties is provided in Table 1.
Table 1. Specifications of measurement instruments used in the experimental study.
These uncertainty values were subsequently propagated to the calculated performance parameters following a standard uncertainty analysis procedure, as described in Section 2.6.

2.6. Uncertainty Analysis

The experimental uncertainty of the measured and calculated parameters was evaluated using the root-sum-square (RSS) method proposed by Kline and McClintock, which combines the individual uncertainties of the measuring instruments listed in Table 1. This method is widely adopted in experimental thermal system analyses and provides a reliable estimate of overall measurement uncertainty.
Based on this approach, the combined uncertainty in the calculated energy efficiency was determined to be ±3.1%, mainly influenced by uncertainties in temperature difference measurements and mass flow rate estimation. Similarly, the uncertainty associated with the exergy efficiency was calculated as ±3.8%, reflecting the higher sensitivity of exergy calculations to small temperature gradients, particularly near ambient conditions.
These uncertainty levels are within the ±5% range commonly accepted in experimental solar thermal studies, indicating that the reported results are sufficiently accurate and reliable for comparative performance evaluation. The complete experimental dataset used in the analyses is provided in Table S1 (Supplementary Materials).

3. Theoretical Framework

A rigorous assessment of the performance of a solar air heater (SAH) requires the simultaneous consideration of fluid flow behavior, convective heat transfer characteristics, thermodynamic efficiency, and environmental impact. Conventional SAH studies have predominantly focused on thermo-hydraulic parameters, most notably the Reynolds number ( R e ), Nusselt number ( N u ), and friction factor ( f )—to describe flow regimes, turbulence generation, and heat transfer enhancement mechanisms [32,33]. Although these parameters provide valuable insight into the underlying flow physics, performance evaluation based solely on heat transfer or thermal efficiency does not fully capture the overall effectiveness of the system.
In practical applications, solar thermal systems must not only enhance heat transfer but also convert the absorbed solar energy into useful thermal output with minimal thermodynamic irreversibility and environmental burden. In this context, exergy analysis plays a crucial role by quantifying the quality of energy and identifying sources of irreversibility within the system, particularly under variable operating and control conditions. Moreover, the growing emphasis on sustainable energy technologies necessitates the incorporation of environmental performance indicators, such as CO2 mitigation potential and sustainability indices, to evaluate the broader implications of system operation beyond purely thermal considerations.
Accordingly, the present study adopts an integrated performance evaluation framework that combines thermo-hydraulic, thermodynamic, and sustainability-based metrics. The overall system behavior is examined by correlating the Reynolds number ( R e ) ,   Nusselt number ( N u ), relative geometric roughness ( e / D h ) , and frictional losses with exergy efficiency ( η e x ) and CO2 mitigation potential. This unified framework enables a holistic assessment of how flow modification through adjustable baffle inclination influences not only heat transfer enhancement, but also thermodynamic efficiency and environmental effectiveness.
By integrating these complementary performance indicators, the proposed framework provides a physically consistent and comprehensive basis for evaluating the SAH performance, allowing meaningful comparison among different baffle configurations and operating conditions.

3.1. Dimensionless Geometric Parameters

The solar air heater (SAH) investigated in this study incorporates ten rectangular baffles arranged in five successive rows along the airflow direction to promote flow mixing and enhance convective heat transfer. The effective absorber area of the collector is 1760 × 860 mm, while the overall collector dimensions are 2200 × 940 mm. Each baffle element has a length of 275 mm, a height of 30 mm, and a thickness of 4 mm, with a uniform pitch of 300 mm between consecutive rows.
The airflow passage has a rectangular cross-section, and its characteristic length scale is defined using the hydraulic diameter, which is calculated as four times the flow area divided by the wetted perimeter. The hydraulic diameter, expressed in terms of the duct width ( W ) and height ( H ) , is consistently employed in the evaluation of Reynolds and Nusselt numbers throughout the analysis.
Two dimensionless geometric parameters are used to characterize the baffle configuration: the relative roughness ratio (e/Dh) and the pitch-to-height ratio (p/e). For the present design, these parameters are calculated as e / D h   =   0.0397 and p / e   =   9.17 , respectively. Both values lie within the ranges commonly recommended in the literature for artificially roughened solar air heater ducts ( e / D h   ≈   0.03 − 0.05   and   p / e   ≈   7 − 10 ) . Such parameters are known to strongly influence flow separation, recirculation intensity, and reattachment behavior downstream of roughness elements, thereby governing the trade-off between heat transfer enhancement and pressure drop penalties [30,31].
The convective heat transfer performance of the SAH is quantified using the Nusselt number, which represents the dimensionless heat transfer coefficient and serves as a primary indicator of thermal enhancement. Since the Prandtl number remains nearly constant within the investigated temperature range, the Nusselt number can be modeled primarily as a function of the Reynolds number (Re) and the baffle inclination angle ( θ ). Based on logarithmic regression analysis of the experimental data, empirical   N u − R e − θ   correlations were developed for different outlet temperature levels, as presented in the following subsection.
The hydraulic diameter of the rectangular duct is calculated as:
D h = 2 W H W + H
The Nusselt number, which defines the convective heat transfer coefficient, is expressed as:
N u = h D h k
For a 54 °C outlet temperature:
N u = 0.3879   R e 0.1691 ( s i n   θ ) 0.2464
For a 60 °C outlet temperature:
N u = 3.13 × 10 − 4   R e 0.9909 ( s i n   θ ) − 0.1220
The Reynolds number, representing the flow regime, is calculated as:
R e = ρ V D h μ
where ρ is air density, μ is dynamic viscosity, and V is the mean air velocity. Temperature dependent properties were obtained from Engineering Equation Solver (EES). As with conventional SAHs, increasing Re enhances turbulence and heat transfer but incurs additional frictional losses. The experimentally derived friction factor correlation valid for both outlet temperatures is:
f = 0.016692   R e − 0.25
This relation provides a generalized hydrodynamic model for the baffled rectangular duct.

3.2. Energy, Exergy, and Sustainability Analyses

Energy and exergy analyses form the core of thermodynamic assessment in solar thermal systems. While energy analysis quantifies the total heat transferred, exergy analysis evaluates the useful work potential of that energy and identifies sources of irreversibility [34,35]. Numerous studies have shown that combined energy–exergy evaluation is essential for optimal SAH design [36,37,38,39,40].

3.2.1. Energy Analysis

Applying a steady state energy balance to the SAH control volume yields:
Q ˙ i = m ˙ o h o V o 2 2 − m ˙ i h i V i 2 2 + Q ˙ l
Because the mass flow rate remains constant:
m ˙ i = m ˙ o = m ˙
and enthalpy is expressed as:
h = c p T
The solar energy input is:
Q ˙ i = I A c
Substituting into Equation (8):
I A c − Q ˙ l = m ˙ c p ( T o − T a )
The collector energy efficiency becomes:
η e n = m ˙ c p ( T o − T a ) I A c
For a glazed collector with transmissivity–absorptivity product (τα):
Q ˙ i = τ α I A c
yielding the practical efficiency:
η e n , r e a l = m ˙ c p ( T o − T a ) τ α I A c

3.2.2. Exergy Analysis

The exergy balance for a steady state control volume is [38]:
E x ˙ d = ∑ E x ˙ i − ∑ E x ˙ o
Incoming exergy consists of solar and inlet air exergy:
∑ E x ˙ i = E x ˙ r , i + E x ˙ a , i
Solar exergy is computed using the Petela model [41]:
E x ˙ r , i = 1 − 4 3 T a T r + 1 3 T a T r 4 I A c α
with T_r = 5777 K. The inlet air exergy is:
E x ˙ a , i = m ˙ c p ( T i − T a ) − T a l n T i T a
Outlet exergy is:
∑ E x ˙ o = E x ˙ a , o + E x ˙ r , o
E x ˙ a , o = m ˙ c p ( T o − T a ) − T a l n T o T a
Radiative exergy loss:
E x ˙ r , o = Q ˙ r , o 1 T a T p
with:
Q ˙ r , o = ε σ A c ( T p 4 − T a 4 )
The exergy efficiency is:
η e x = E x ˙ a , o E x ˙ a , i + E x ˙ r , i

3.2.3. Sustainability and Environmental Assessment

The Sustainability index (SI), widely used in exergy based environmental evaluations, is defined as:
S I = 1 1 − η e x
A higher SI indicates reduced irreversibility and improved thermodynamic sustainability. Classification ranges are shown in Table 2.
Table 2. Classification of Sustainability index and Exergy Efficiency.
The avoided CO2 emissions associated with replacing fossil fuel based heating are estimated as:
E C O 2 = E s × E F
where the annual useful energy output is:
E s = G a A c η e n
Total avoided emissions over the system lifetime (n = 20 years):
E C O 2 , t o t a l = E C O 2 × n
An emission factor of EF = 0.434 kg CO2/kWh was used, corresponding to the national grid average in Türkiye [42].

4. Results and Discussion

4.1. Thermo-Hydraulic Performance

The experimental dataset was obtained under well-controlled outdoor conditions characterized by nearly constant solar irradiance, low wind velocity, and relatively high ambient temperatures. This ensured a high level of internal consistency and repeatability in the measurements. However, it should be noted that the limited range of environmental conditions may restrict the direct generalization of the results to climates with highly fluctuating irradiance or strong wind effects. This limitation is explicitly acknowledged, and the correlations presented are therefore most applicable to operating conditions like those tested in this study.

4.1.1. Heat Transfer Characteristics (Nu–Re–θ)

The variation in the Nusselt number with Reynolds number and baffle inclination angle is presented in Figure 6 for both outlet temperature setpoints (54 °C and 60 °C). In all cases, the Nusselt number increases monotonically with Reynolds number, confirming that forced convection is the dominant heat transfer mechanism within the air channel.
Figure 6. Variation of Reynolds number with Nusselt number for different outlet temperature setpoints and baffle angles.
At 54 °C, the influence of baffle inclination is clearly discernible, indicating that geometric flow redirection effectively intensifies local turbulence and disrupts the thermal boundary layer near the absorber surface. At 60 °C, however, the enhancement effect of baffle inclination becomes weaker. This behavior is attributed to the higher Reynolds numbers required to maintain the elevated outlet temperature, where the flow approaches a fully developed turbulent regime and additional geometric disturbance yields diminishing marginal gains.
The experimentally derived Nu–Re–θ correlations exhibit strong agreement with the measured data, yielding coefficients of determination of R2 = 0.922 and R2 = 0.959, with corresponding MAPE values of 3.48% and 2.36% for the 54 °C and 60 °C cases, respectively. These metrics confirm the robustness of the proposed heat transfer models within the operating range investigated.

4.1.2. Friction Factor Characteristics (f–Re)

The hydrodynamic behavior of the system was assessed through the friction factor–Reynolds number relationship, as shown in Figure 7a,b for outlet temperatures of 54 °C and 60 °C, respectively. In both cases, the friction factor decreases with increasing Reynolds number, in agreement with classical turbulent flow behavior in roughened ducts.
Figure 7. (a) Variation in friction factors with Reynolds number at 54 °C outlet temperature; (b) Variation in friction factors with Reynolds number at 60 °C outlet temperature.
A critical observation is that the friction factor exhibits minimal sensitivity to the baffle inclination angle, while remaining strongly governed by the Reynolds number. Although this behavior may initially appear counterintuitive, it can be physically and quantitatively explained by examining the relative contributions of distributed and local pressure losses within the duct.
In the present configuration, the total pressure drop is dominated by global (distributed) frictional losses arising from the channel walls and the cumulative form drag of multiple baffle elements along the duct length. The collapse of the f–Re data for all baffle angles onto a single curve provides quantitative evidence that the overall hydraulic resistance is primarily controlled by inertial effects represented by the Reynolds number. This interpretation is further supported by regression analysis, which yielded the following correlation with nearly perfect agreement:
f = 0.016692   R e − 0.25
The resulting coefficient of determination (R2 ≈ 1.000) and negligible prediction error (MAPE ≈ 0%) indicate that the inclusion of an angular term does not improve the predictive capability of the friction factor model.
From a fluid-dynamic perspective, variation in the baffle inclination mainly affects local flow structures, such as turbulence intensity and boundary-layer disruption near the absorber surface. While these localized effects significantly enhance heat transfer, the additional pressure loss associated with flow redirection around individual baffles remains marginal when compared to the total hydraulic resistance accumulated over the entire duct. Minor deviations observed at lower Reynolds numbers are attributed to transitional flow features and increased sensitivity of pressure measurements in the wake regions downstream of the baffles.

4.1.3. Pressure Loss Trade-Off and Performance Evaluation Perspective

In forced-convection solar air heaters, thermal enhancement techniques must be evaluated together with their impact on pressure losses, as both factors directly influence the overall system performance and auxiliary energy consumption. This balance is commonly assessed through performance evaluation criteria (PEC), which quantify the trade-off between heat transfer enhancement and the associated hydraulic cost.
In the present system, the experimental results indicate that variations in baffle inclination significantly enhance heat transfer performance while exerting only a marginal influence on the global pressure loss characteristics. The near independence of the friction factor from the baffle angle demonstrates that the hydraulic cost associated with pressure losses does not scale proportionally with thermal enhancement. Instead, pressure losses remain primarily governed by the Reynolds number and distributed frictional effects along the duct.
This behavior implies a favorable thermal–hydraulic trade-off, particularly for solar-assisted or photovoltaic-powered fan systems, where available auxiliary power is inherently limited. Under such operating conditions, achieving higher outlet air temperatures or improved heat transfer rates without a noticeable increase in hydraulic cost represents a key design advantage.
Although a comprehensive PEC analysis incorporating fan power measurements is beyond the scope of the present experimental setup, the observed thermo-hydraulic trends strongly suggest that the proposed baffle configuration provides a net performance benefit. Specifically, the heat transfer gains achieved through baffle angle adjustment outweigh the associated pressure loss trade-offs within the investigated Reynolds number and angular ranges.

4.1.4. Correlation Reliability and Uncertainty

The experimentally measured Nusselt number (Nu) and friction factor (f) data were systematically validated against the proposed empirical correlations to assess their reliability and predictive capability. Regression analysis revealed angular exponents of n = +0.2464 for the 54 °C outlet temperature and n = −0.1220 for the 60 °C condition. These values indicate that baffle inclination contributes positively to convective heat transfer at moderate angles (15–45°), where flow redirection effectively intensifies local turbulence and boundary-layer disruption. At higher outlet temperatures and Reynolds numbers, however, the turbulence field approaches a saturation state, leading to diminishing marginal heat transfer enhancement as the baffle angle exceeds approximately 60°.
A comprehensive uncertainty analysis was conducted for both operating temperatures using the Kline–McClintock method, which accounts for the propagation of measurement uncertainties through the calculated performance parameters. The combined uncertainty in mass flow rate was determined to be 3.33% (±0.00027 kg s−1). The primary contributors to the overall uncertainty budget were identified as follows: heat transfer rate (3.01%), solar irradiance (2.00%), energy efficiency (3.61%), and exergy efficiency (4.14%).
All measurement instruments were factory calibrated prior to experimentation, and only quasi-steady-state data were considered in the analysis to minimize transient effects. The resulting total combined uncertainties remained below ±5%, which is consistent with uncertainty ranges commonly reported for roughened-duct and baffle-enhanced solar air heater systems in the literature.
Overall, the close agreement between the experimental dataset and the proposed Nu and f correlations, together with the bounded uncertainty levels, confirms the statistical robustness and physical consistency of the developed models. These findings support the applicability of the correlations for performance prediction and design analysis of solar air heaters incorporating fixed or adjustable baffle configurations.

4.2. Energy, Exergy, and Sustainability Performance

4.2.1. Energy Efficiency

Increasing the baffle inclination produced a clear enhancement in energy efficiency at both outlet temperatures (54 °C and 60 °C). This improvement results from stronger turbulence, boundary layer disruption, and intensified mixing near the absorber surface as the inclination angle increases. The corresponding trends are shown in Figure 8.
Figure 8. Energy efficiency versus baffle angle at outlet temperatures of 54 °C and 60 °C.
For the 54 °C condition, the energy efficiency rose from 27.5% at 0° to approximately 62–63% at 60°. A pronounced performance jump was observed between 15° and 45°, indicating a transition region where turbulent structures become significantly stronger. Beyond 60°, the rate of improvement diminished, suggesting that the flow approaches a partially saturated turbulent regime.
At 60 °C, the efficiency values were consistently higher, increasing from 30.96% at 0° to 76.83% at 90°. A plateau of roughly 52–55% emerged between 15° and 45°, reflecting a more stabilized flow regime driven by the higher absorber surface temperature. Overall, these patterns align well with previous findings indicating that intermediate baffle inclinations (30–60°) provide the most favorable conditions for effective heat transfer enhancement.
Although the instantaneous thermal efficiency reached a peak value of 76.8%, these results should be interpreted with caution. In experimental practice, potential error sources such as minor air leakages at duct junctions, thermal bridging across the collector casing, and the localized nature of point-measurements (PT100 sensors) may introduce uncertainties. While the calculated efficiency reflects the active heat gain imparted to the airflow, the absolute values are sensitive to these external factors. Therefore, the reported efficiency should be viewed as a comparative metric demonstrating the improvement over passive configurations rather than an absolute maximum applicable to all long-term operating conditions.

4.2.2. Exergy Efficiency

Exergy efficiency ( η e x ) exhibits a fundamentally different behavior compared to energy efficiency, as it directly reflects the quality of the transferred heat and the magnitude of thermodynamic irreversibilities within the system. Unlike energy-based metrics, exergy efficiency penalizes low-temperature heat gains, making it a more restrictive but physically insightful indicator. The variation of η e x with baffle inclination angle for both operating conditions is presented in Figure 9.
Figure 9. Exergy efficiency vs. baffle angle at outlet temperatures of 54 °C and 60 °C.
For the 54 °C outlet temperature, the exergy efficiency ranges between 1.30% and 1.99%, showing only moderate sensitivity to baffle inclination. The relatively small temperature rise between the inlet air and the absorber surface limits the recoverable work potential, thereby constraining the magnitude of useful exergy despite improvements in convective heat transfer. At the 60 °C condition, η e x increases to values between 1.24% and 2.69%, reaching its maximum at a baffle angle of 90°. This enhancement is attributed to two combined mechanisms:
(i)
the higher outlet temperature improves the thermodynamic quality of the delivered heat, and
(ii)
steeper baffle inclinations intensify turbulence and convective transport, reducing local thermal resistance.
Despite these relative improvements, the absolute values of exergy efficiency remain below 3% for all configurations. This behavior is not indicative of poor system performance, but rather reflects the inherent thermodynamic limitation of low-temperature solar air heaters. In the present analysis, solar radiation is treated as a high-grade energy source with an effective radiation temperature of approximately 5777 K, whereas the absorber and air stream operate at temperatures close to 330 K. The large temperature gap between the source and the sink during heat absorption constitutes the dominant mechanism of entropy generation, leading to substantial exergy destruction regardless of internal flow enhancements.
This interpretation is further supported by the Sustainability index results discussed in Section 4.2.3. The near-unity SI values indicate that the majority of the supplied solar exergy is unavoidably destroyed at the source–collector interface, while geometric modifications primarily affect secondary irreversibilities associated with internal convection. Consequently, improvements in baffle geometry yield incremental gains in exergy efficiency without fundamentally altering the overall exergy balance.
From a design perspective, reducing exergy destruction in such systems requires strategies that address the primary irreversibility mechanisms, rather than internal flow control alone. Potential redesign approaches include selective absorber coatings to minimize radiative losses, improved optical and thermal insulation to reduce heat leakage, and hybrid system concepts (e.g., PV/T integration) that enable direct utilization of high-grade solar exergy. Within the constraints of the present configuration, baffle inclination remains an effective tool for enhancing heat transfer and moderately improving exergy efficiency, even though the absolute exergetic performance is bounded by fundamental thermodynamic limits.

4.2.3. Sustainability Index

The Sustainability index (SI) values obtained in this study remain close to unity, ranging approximately between 1.01 and 1.02 for both outlet temperature levels, as shown in Figure 10. According to the classification presented in Table 2, such values indicate operation in a regime characterized by high thermodynamic irreversibility.
Figure 10. Sustainability index vs. baffle angle at outlet temperatures of 54 °C and 60 °C.
This behavior does not contradict the favorable thermal and thermo-hydraulic performance reported earlier; rather, it reflects the intrinsic limitations of low-temperature solar thermal air heaters. In the present exergy formulation, solar radiation is evaluated using the Petela model with an effective radiation temperature of Tr = 5777 K, while the absorber and air stream operate at much lower temperatures. As a result, a substantial portion of the incoming solar exergy is unavoidably destroyed due to the large source–sink temperature gap, regardless of internal flow enhancements.
Variations in baffle inclination do influence the convective heat transfer and lead to modest improvements in exergy efficiency; however, their effect on the Sustainability index remains limited. This is because geometric modifications primarily affect internal irreversibilities, whereas the dominant exergy destruction mechanisms originate from optical losses and heat transfer across large temperature differences between the solar source and the collector. Consequently, changes in baffle geometry lead to incremental, rather than transformative, variations in SI.
From a design perspective, this observation highlights that improving exergetic sustainability in air-based solar collectors requires strategies targeting the primary sources of exergy destruction. Such strategies include selective absorber coatings, improved optical and thermal insulation, and system hybridization (e.g., PV/T integration) to directly utilize high-grade solar exergy. Within the present configuration, baffle inclination angles in the range of 60–75° provide the most balanced compromise between heat transfer enhancement and associated hydraulic costs, even though the absolute SI values remain constrained by fundamental thermodynamic limits.

4.3. Empirical Model for Required Airflow Velocity

The influence of baffle inclination on the airflow demand required to maintain the prescribed outlet temperatures was investigated under an average solar irradiance of 850 W m−2. As the inclination angle increases, both turbulence intensity and hydraulic resistance rise, leading to a higher airflow requirement to sustain the same thermal output. Accordingly, for the 54 °C outlet temperature, the required inlet air velocity increases from 0.37 m s−1 at 0° to 0.97 m s−1 at 90°, while for 60 °C, the corresponding range varies from 0.32 m s−1 to 0.91 m s−1.
This behavior results from two coupled mechanisms:
(i)
enhanced boundary layer disruption and mixing induced by steeper baffle angles, and
(ii)
geometric flow constriction accompanied by intensified recirculation zones, which increase pressure losses and consequently the auxiliary fan power demand.
As illustrated in Figure 11, the angular variation in the required airflow velocity exhibits a clear and nearly linear increasing trend for both operating temperatures. Slightly lower airflow velocities are sufficient at 60 °C, which can be attributed to the higher absorber plate temperature ( T p l a t e ). The elevated plate temperature strengthens buoyancy-assisted convection, thereby reducing the mechanical airflow required to achieve the target outlet temperature.
Figure 11. Variation in required airflow velocity with baffle inclination angle at outlet temperatures of 54 °C and 60 °C.
To quantify this relationship, a multiple linear regression model was developed to predict the inlet air velocity ( V ) as a function of baffle inclination angle ( θ ), absorber plate temperature ( T p l a t e ), and outlet air temperature ( T o u t ):
V = 0.00617   θ − 0.00402   T p l a t e + 0.01199   T o u t + 2.67114 ( 29 )
The regression model demonstrates strong statistical robustness, yielding a coefficient of determination of R 2 = 0.94 , a root mean square error of RMSE = 0.06 m s−1, and a mean absolute percentage error of MAPE = 4.1%. Residual analysis confirmed a random distribution with no systematic bias, indicating that the linear formulation adequately captures the dominant physical trends within the investigated parameter range.
The physical significance of the regression coefficients is consistent with the underlying thermo-hydraulic behavior. An increase in baffle angle ( θ ) necessitates a higher airflow velocity due to increased hydraulic resistance and recirculation intensity. Conversely, a higher absorber plate temperature ( T p l a t e ) reduces the required airflow, as buoyancy-assisted convection contributes more effectively to heat transfer. An increase in the target outlet temperature ( T o u t ) demands greater heat extraction from the absorber, which in turn requires higher airflow rates.
Although T p l a t e and T o u t are thermodynamically related, collinearity effects were found to be limited within the present dataset. Variance inflation factors (VIF) remained below commonly accepted thresholds, indicating that the independent variables contribute distinct physical information to the model. Therefore, the inclusion of both parameters improves predictive accuracy without compromising model stability.
It should be noted that the regression model was derived from a controlled experimental dataset rather than a separate validation dataset. Nevertheless, the low prediction errors, strong statistical indicators, and consistency with experimental observations support the reliability of the proposed model within its defined applicability range: 0 ° ≤ θ ≤ 90 °, 0.3 ≤ V ≤ 1.0 m s−1, and 54 °C ≤ T o u t ≤ 60 °C.
From an engineering perspective, these results confirm that baffle inclination is the dominant geometric parameter governing the trade-off between heat transfer enhancement and increased airflow demand. Both experimental trends and regression predictions consistently indicate that the 60–75° inclination range offers the most effective compromise, providing substantial thermal enhancement while limiting additional auxiliary fan power requirements.
The proposed airflow velocity regression model also provides a direct link between thermo-hydraulic performance, auxiliary power demand, and sustainability-related indicators. Since the required inlet velocity is directly associated with fan power consumption, the model enables indirect assessment of the pressure-loss-related energy expenditure accompanying heat transfer enhancement. In this context, higher baffle inclination angles, while improving heat transfer, lead to increased airflow demand and thus higher mechanical energy input.
From a performance evaluation criterion (PEC) perspective, the regression results confirm that thermal gains obtained beyond a certain inclination angle are progressively offset by increased airflow requirements. This behavior explains why the optimal operating range identified in this study (60–75°) simultaneously corresponds to favorable heat transfer enhancement, moderate airflow demand, and stable Sustainability index values. Consequently, the airflow regression model serves not only as a predictive design tool, but also as a practical framework for balancing thermal performance, fan power requirements, and exergetic sustainability in baffled solar air heater systems.

4.4. Design Synthesis, Long-Term Impact, and Limitations

The long-term performance of the PLC-controlled solar air heater (SAH) was assessed by combining experimentally measured thermal efficiencies with region-specific solar irradiance data. Based on an average annual solar resource of 1311 kWh m−2 for the Manisa region, the system can deliver 1025.9 kWh year−1 of useful thermal energy at a 54 °C outlet temperature and 1087.2 kWh year−1 at 60 °C, as summarized in Table 3. Over a nominal operational lifetime of 20 years, this corresponds to a cumulative thermal output of approximately 20.5–21.7 MWh, indicating that a single collector unit can reliably support long-term low-temperature heating demands, particularly in agricultural and industrial drying applications.
Table 3. Thermal efficiency, annual useful heat gain, and long-term performance indicators of the PLC-controlled SAH.
From an environmental perspective, the projected long-term operation of the system indicates a potential avoidance of approximately 8.90–9.45 tons of CO2 over its service life, assuming displacement of grid-based electric heating and adopting the national emission factor of 0.434 kg CO2 kWh−1. It is important to emphasize, however, that these estimates represent an idealized upper-bound scenario, derived from peak thermal performance observed under controlled experimental conditions.
In real-world operation, several factors may reduce the effective long-term performance. These include dust accumulation on the glazing surface (soiling), material aging, seasonal variations in solar incidence angle, and fluctuations in ambient conditions. In addition, experimental uncertainties related to minor duct leakages, sensor placement, and internal thermal losses imply that the reported efficiency values should be interpreted as representative of maximum achievable performance, rather than continuous year-round operation. Consequently, while the projected CO2 mitigation highlights the environmental potential of the system, actual offsets are expected to vary depending on site-specific conditions and maintenance practices.
From a design synthesis standpoint, the 60–75° baffle inclination range emerges as the most practical operating window. Within this range, the system achieves a favorable compromise between enhanced heat transfer performance and increased hydraulic resistance, thereby limiting auxiliary fan power demand. This finding is consistent with the thermo-hydraulic, exergy, and sustainability analyses presented in previous sections and supports the selection of this angular range for long-term operation.
A preliminary life-cycle consideration further supports the environmental viability of the proposed system. Based on typical embodied carbon values for galvanized steel and tempered glass, the estimated manufacturing-related carbon footprint is offset within approximately 1.5–2.0 years of operation. As a result, nearly 90% of the system’s service life contributes to net environmental benefits. From an economic perspective, the annual useful heat production corresponds to approximately 4.8–5.0% of the system’s initial capital cost, yielding a simple payback period of 6–8 years, depending on the selected operating temperature and auxiliary fan power requirements.
Overall, the combined thermal, thermo-hydraulic, exergy, and long-term performance analyses demonstrate that the proposed PLC-controlled SAH offers a balanced and realistic pathway toward sustainable low-temperature heat supply. Despite inherent thermodynamic limitations associated with air-based solar collectors, the system presents robust environmental and economic prospects, particularly for decentralized agricultural drying and low-grade industrial heating applications.

5. Conclusions

This study presented a comprehensive 3E (energy–exergy–environmental) assessment and design synthesis of a PLC-controlled solar air heater (SAH) equipped with dynamically adjustable baffle geometry. The adaptive control strategy successfully maintained outlet air temperatures of 54 °C and 60 °C, with rapid stabilization times on the order of 3–10 s, demonstrating a clear operational advantage over conventional passive SAH configurations.
From a thermal performance perspective, increasing the baffle inclination significantly enhanced convective heat transfer within the air channel. The effective heat transfer coefficient and corresponding Nusselt number increased monotonically with Reynolds number and baffle angle, leading to a substantial rise in thermal efficiency from 27.5% at 0° to a maximum of 76.8% at 90°. These improvements confirm the strong role of turbulence intensification, boundary-layer disruption, and secondary flow formation in enhancing heat transfer.
Despite the pronounced thermal enhancement, the hydrodynamic penalty remained moderate. The friction factor was found to be predominantly governed by the Reynolds number and exhibited negligible sensitivity to baffle inclination, indicating that global distributed losses dominate over local angle-dependent effects. This behavior resulted in a favorable thermo-hydraulic performance balance, particularly within the 60–75° baffle inclination range, which emerged as the most practical operating window.
The exergy analysis revealed relatively low exergy efficiencies (1.24–2.69%) and near-unity Sustainability index values (SI ≈ 1.001–1.002), which are intrinsic characteristics of low-temperature solar air heaters. These results reflect the dominant irreversibilities associated with the large temperature gap between the solar radiation source and the absorber–air stream, as well as mechanical exergy losses related to airflow generation. Importantly, the limited variation in SI does not contradict the favorable energy and thermo-hydraulic performance; rather, it highlights the fundamental thermodynamic constraints of air-based solar thermal systems.
To support system operation and control, a regression-based airflow velocity model was developed, linking baffle inclination, absorber plate temperature, and outlet air temperature to the required inlet airflow. This model provides a practical engineering tool for fan-speed optimization, indirectly connecting heat transfer enhancement with auxiliary power demand, performance evaluation criteria (PEC), and sustainability considerations.
Long-term performance projections based on regional solar irradiance data indicate that the proposed SAH can deliver approximately 20–22 MWh of useful thermal energy and mitigate around 9 tons of CO2 emissions over a 20-year operational lifetime. While these estimates represent an upper-bound scenario, they demonstrate the strong environmental potential of the system for low-temperature applications, such as agricultural and industrial drying.
In comparison with previous studies on multi-V ribs, perforated ribs, and other turbulence-promoting geometries, the present results confirm that excessive blockage may degrade overall thermo-hydraulic performance. The dynamically adjustable baffle mechanism introduced in this work offers a unique advantage by enabling real-time optimization of the trade-off between heat transfer enhancement and airflow demand.
Future research should focus on the following:
(i)
Integrating life-cycle and cost–benefit optimization into the control framework;
(ii)
Exploring advanced working fluids, such as nanofluids or phase change materials (PCMs), to improve thermal storage and exergy utilization;
(iii)
Implementing machine-learning-based predictive control strategies to dynamically adjust baffle angle and fan speed under variable climatic conditions;
(iv)
Extending the analysis to multi-collector arrays and long-term field testing to further assess system durability and real-world performance.
Overall, the proposed PLC-controlled SAH demonstrates strong potential as a flexible, efficient, and environmentally viable solution for sustainable low-grade heat supply.

Supplementary Materials

The following supporting information can be downloaded at: https://www.mdpi.com/article/10.3390/su18020719/s1, Figure S1: Adjustable baffle mechanism (detail view); Figure S2: Motor–shaft assembly; Figure S3: Pump and hydraulic system; Figure S4: PLC control interface and program flow; Figures S5: Experimental setup (front, side, and rear views); Figure S6: Collector cross-section and measurement layout, Table S1: Full experimental dataset (Excel file).

Funding

This research was supported by the Scientific Research Projects Coordination Unit of Manisa Celal Bayar University (MCBU BAP ID 2017-070) and by the Scientific and Technological Research Council of Türkiye (TÜBİTAK ID 600116). The APC was funded by the author.

Institutional Review Board Statement

Not applicable.

Data Availability Statement

The data supporting the findings of this study, including raw experimental measurements, PLC control logs, and processed performance indicators, are available from the corresponding author upon reasonable request.

Acknowledgments

The author gratefully acknowledges the research support provided by Manisa Celal Bayar University (MCBU BAP) and the Scientific and Technological Research Council of Tür-kiye (TÜBİTAK). During the preparation of this manuscript, ChatGPT (OpenAI, GPT-5.1) and DeepL were used solely for language polishing and translation purposes. All scientific content, analyses, and interpretations were entirely produced and verified by the author.

Conflicts of Interest

The author declares no conflicts of interest. The funders had no role in the design of the study; in the collection, analyses, or interpretation of data; in the writing of the manuscript; or in the decision to publish the results.

Abbreviations

SymbolDescriptionUnit
I Solar irradianceW/m2 ρ Air densitykg/m3
A c Collector surface aream2 μ Dynamic viscosityPa·s
Q ˙ Heat transfer rateW D h Hydraulic diameterm
m ˙ Mass flow ratekg/s H Convective heat transfer coefficientW/(m2·K)
c p Specific heat of airJ/(kg·K) k Thermal conductivity of airW/(m·K)
T a Ambient temperatureK N u Nusselt number-
T i Inlet air temperatureK R e Reynolds number-
T o Outlet air temperatureK f Friction factor-
T p Plate temperatureK τ Transmittance of glazing-
V Air velocitym/s α Absorptance of absorber plate-
S I Sustainability index- ε Emissivity-
σ Stefan–Boltzmann constantW/(m2·K4)

References

  1. Fudholi, A.; Sopian, K. A review of solar air flat plate collector for drying application. Renew. Sustain. Energy Rev. 2019, 102, 333–345. [Google Scholar] [CrossRef] [Scilit]
  2. Bożym, M.; Bok, A. Advantages and disadvantages of the solar drying of sewage sludge in Poland. Czas. Tech. 2017, 12, 171–179. [Google Scholar] [CrossRef] [Scilit]
  3. Fernandes, L.; Tavares, P.B. A Review on Solar Drying Devices: Heat Transfer, Air Movement and Type of Chambers. Solar 2024, 4, 15–42. [Google Scholar] [CrossRef] [Scilit]
  4. Benli, H. Experimentally derived efficiency and exergy analysis of a new solar air heater having different surface shapes. Renew. Energy 2013, 50, 58–67. [Google Scholar] [CrossRef] [Scilit]
  5. Dhairiyasamy, R.; Rajendran, S.; Khan, S.A.; Alahmadi, A.A.; Alwetaishi, M.; Ağbulut, Ü. Enhancing thermal efficiency in flat plate solar collectors through internal barrier optimization. Therm. Sci. Eng. Prog. 2024, 54, 102856. [Google Scholar] [CrossRef] [Scilit]
  6. Vengadesan, E.; Arunkumar, T.; Krishnamoorthi, T.; Senthil, S. Thermal performance improvement in solar air heating: An absorber with continuous and discrete tubular and v corrugated fins. Therm. Sci. Eng. Prog. 2024, 48, 102416. [Google Scholar] [CrossRef] [Scilit]
  7. Mahmood, A.J. Thermal evaluation of a double pass unglazed solar air heater with perforated plate and wire mesh layers. Sustainability 2020, 12, 3619. [Google Scholar] [CrossRef] [Scilit]
  8. Abulkhair, H.; Alsaiari, A.O.; Ahmed, I.; Almatrafi, E.; Madhukeshwara, N.; Sreenivasa, B.R. Heat transfer and air flow friction in solar air heaters: A comprehensive computational and experimental investigation with wire-roughened absorber plate. Case Stud. Therm. Eng. 2023, 48, 103148. [Google Scholar] [CrossRef] [Scilit]
  9. Sheelam, S.; Parvathy, C.V. Solar air collector with right-angle triangle corrugations for an indirect type solar dryer for enhancement in performance. J. Therm. Anal. Calorim. 2024, 149, 311–326. [Google Scholar] [CrossRef] [Scilit]
  10. Acır, A.; Ata, İ.; Şahin, İ. Energy and exergy analyses of a new solar air heater with circular type turbulators having different relief angles. Int. J. Exergy 2016, 20, 85–104. [Google Scholar] [CrossRef] [Scilit]
  11. Alaiwi, Y.; Ahmed, T. Solar Air Heaters Classifications and Enhancement: A Review. Babylon. J. Mech. Eng. 2024, 2024, 71–80. [Google Scholar] [CrossRef] [Scilit]
  12. Daliran, A.; Ajabshirchi, Y. Theoretical and experimental research on effect of fins attachment on operating parameters and thermal efficiency of solar air collectors. Inf. Process. Agric. 2018, 5, 411–421. [Google Scholar] [CrossRef] [Scilit]
  13. Karmveer; Gupta, N.K.; Alam, T.; Cozzolino, R.; Bella, G. A descriptive review to access the most suitable rib’s configuration of roughness for the maximum performance of solar air heater. Energies 2022, 15, 2800. [Google Scholar] [CrossRef] [Scilit]
  14. Chang, Y.; Mu, T.; Jia, B. Optimization analysis of the length of baffles for solar air heaters based on CFD. Energy Sources Part A Recover Util. Environ. Eff. 2023, 45, 12405–12422. [Google Scholar] [CrossRef] [Scilit]
  15. Zhu, Q.; Farkas, I.; Buzás, J. Numerical study on the influence of baffle configuration on the thermal performance of solar air heaters. Results Eng. 2025, 27, 106913. [Google Scholar] [CrossRef] [Scilit]
  16. Thapmanee, P.; Phila, A.; Wongcharee, K.; Maruyama, N.; Hirota, M.; Chuwattanakul, V.; Eiamsa-Ard, S. Numerical Methodology for Enhancing Heat Transfer in a Channel with Arc-Vane Baffles. Computation 2025, 13, 71. [Google Scholar] [CrossRef] [Scilit]
  17. Rashid, F.L.; Alkhekany, Z.A.K.; Kurji, H.J.; Ahmad, S.; Chibani, A.; Kezzar, M.; Hammoodi, K.A.; Kadhim, S.A.; Haddad, M.A.N.; Agyekum, E.B. Enhancing the thermal performance of different types of heat exchangers with fins: A comprehensive review. Int. Commun. Heat Mass Transf. 2025, 166, 109177. [Google Scholar] [CrossRef] [Scilit]
  18. Mahanand, Y.; Senapati, J.R. Thermo-hydraulic performance analysis of a solar air heater (SAH) with quarter circular ribs on the absorber plate: A comparative study. Int. J. Therm. Sci. 2021, 161, 106747. [Google Scholar] [CrossRef] [Scilit]
  19. Naphon, P.; Wongwises, S. A review of flow and heat transfer characteristics in curved tubes. Renew. Sustain. Energy Rev. 2006, 10, 463–490. [Google Scholar] [CrossRef] [Scilit]
  20. Matheswaran, M.M.; Arjunan, T.V.; Somasundaram, D. Analytical investigation of exergetic performance on jet impingement solar air heater with multiple arc protrusion obstacles. J. Therm. Anal. Calorim. 2019, 137, 253–266. [Google Scholar] [CrossRef] [Scilit]
  21. Shadi, M.; Farahani, S.D.; Aghdam, A.H. Energy, exergy and economic analysis of solar air heaters with different roughness geometries. J. Solar Energy Res. 2020, 5, 390–399. [Google Scholar] [CrossRef] [Scilit]
  22. Alrashidi, A.; Altohamy, A.A.; Abdelrahman, M.A.; Elsemary, I.M. Energy and exergy experimental analysis for innovative finned plate solar air heater. Case Stud. Therm. Eng. 2024, 59, 104570. [Google Scholar] [CrossRef] [Scilit]
  23. Akpinar, E.K.; Koçyiğit, F. Energy and exergy analysis of a new flat plate solar air heater having different obstacles on absorber plates. Appl. Energy 2010, 87, 3438–3450. [Google Scholar] [CrossRef] [Scilit]
  24. Sharma, A.; Awasthi, A.; Singh, T.; Kumar, R.; Chauhan, R. Experimental investigation and optimization of potential parameters of discrete V down baffled solar thermal collector using hybrid Taguchi–TOPSIS method. Appl. Therm. Eng. 2022, 209, 118250. [Google Scholar] [CrossRef] [Scilit]
  25. Thao, P.B.; Truyen, D.C.; Phu, N.M. CFD analysis and Taguchi based optimization of the thermos-hydraulic performance of a solar air heater duct baffled on a back plate. Appl. Sci. 2021, 11, 4645. [Google Scholar] [CrossRef] [Scilit]
  26. Nowzari, R.; Mirzaei, N.; Parham, K. Selecting the optimal configuration for a solar air heater using the Grey–Taguchi method. Processes 2020, 8, 317. [Google Scholar] [CrossRef] [Scilit]
  27. Chen, X.; Guan, L.; Yang, C.; Ge, P.; Xia, J. A novel optimal control method for building cooling water systems with variable speed condenser pumps and cooling tower fans. Buildings 2025, 15, 3568. [Google Scholar] [CrossRef] [Scilit]
  28. Gang, H.; Bing, L. Intelligent optimization of solar air heating system in large scale construction of and its application. Int. J. Smart Home 2016, 10, 99–106. [Google Scholar] [CrossRef] [Scilit]
  29. Cui, X.; Kou, Z.; Qiao, Y. Water level control system for solar water heating engineering based on PLC. In Proceedings of the 2019 IEEE 3rd Information Technology, Networking, Electronic and Automation Control Conference (ITNEC), Chengdu, China, 15–17 March 2019; pp. 1625–1628. [Google Scholar] [CrossRef] [Scilit]
  30. Zayed, M.E.; Irshad, K.; Rehman, S.; Kabeel, A.E.; Attia, M.E.H.; Abdelrazik, A.S.; Alqahtani, T. Performance appraisal of a modified finned solar air collector thermally assisted by a smart-switchable cover for constant outlet hot air temperature: Numerical investigation. Energy Nexus 2025, 19, 100529. [Google Scholar] [CrossRef] [Scilit]
  31. Zayed, M.E.; Kabeel, A.E.; Shboul, B.; Ashraf, W.M.; Ghazy, M.; Irshad, K.; Zayed, A.A. Performance augmentation and machine learning-based modeling of wavy corrugated solar air collector embedded with thermal energy storage: Support vector machine combined with Monte Carlo simulation. J. Energy Storage 2023, 74, 109533. [Google Scholar] [CrossRef] [Scilit]
  32. Saini, S.K.; Saini, R.P. Development of correlations for Nusselt number and friction factor for solar air heater with roughened duct having arc shaped wire as artificial roughness. Sol. Energy 2008, 82, 1118–1130. [Google Scholar] [CrossRef] [Scilit]
  33. Kumar, A.; Bhagoria, J.L.; Sarviya, R.M. Heat transfer and friction correlations for artificially roughened solar air heater duct with discrete W shaped ribs. Energy Convers. Manag. 2009, 50, 2106–2117. [Google Scholar] [CrossRef] [Scilit]
  34. Bejan, A. Advanced Engineering Thermodynamics, 4th ed.; John Wiley & Sons: Hoboken, NJ, USA, 2016. [Google Scholar]
  35. Dincer, I.; Rosen, M.A. Exergy: Energy, Environment and Sustainable Development, 2nd ed.; Newnes: Oxford, UK, 2012. [Google Scholar]
  36. Reddy, J.; Das, B.; Negi, S. Energy, exergy, and environmental (3E) analyses of reverse and cross corrugated trapezoidal solar air collectors: An experimental study. J. Build. Eng. 2021, 41, 102434. [Google Scholar] [CrossRef] [Scilit]
  37. Bahrehmand, D.; Ameri, M.; Gholampour, M.J. Energy and exergy analysis of different solar air collector systems with forced convection. Renew. Energy 2015, 83, 1119–1130. [Google Scholar] [CrossRef] [Scilit]
  38. Hassan, A.; Nikbakht, A.M.; Fawzia, S.; Yarlagadda, P.; Karim, A. A comprehensive review of the thermohydraulic improvement potentials in solar air heaters through an energy and exergy analysis. Energies 2024, 17, 1526. [Google Scholar] [CrossRef] [Scilit]
  39. Cortes, A.; Piacentini, R. Improvement of the efficiency of a bare solar collector by means of turbulence promoters. Appl. Energy 1990, 36, 253–261. [Google Scholar] [CrossRef] [Scilit]
  40. Gürel, A.E.; Yıldız, G.; Ergün, A.; Ceylan, İ. Exergetic, economic and environmental analysis of temperature controlled solar air heater system. Clean. Eng. Technol. 2022, 6, 100369. [Google Scholar] [CrossRef] [Scilit]
  41. Petela, R. Exergy of undiluted thermal radiation. Sol. Energy 2003, 74, 469–488. [Google Scholar] [CrossRef] [Scilit]
  42. TEİAŞ. Türkiye Electricity Generation Carbon Intensity Report, Türkiye Elektrik İletim A.Ş. 2023. Available online: https://www.teias.gov.tr/turkiye-elektrik-uretim-iletim-istatistikleri (accessed on 20 October 2025).
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Article Metrics

Citations

Article Access Statistics

Multiple requests from the same IP address are counted as one view.