Search Results (391)

Perovskite quantum dots (PQDs) based on CsPbX₃ (X = Cl, Br, I) have attracted extensive attention due to their outstanding optoelectronic properties; however, their practical applications are hindered by poor environmental stability. In this work, a sequential surface-modification strategy is developed to address these limitations. First, CsPbBr₃ PQDs are passivated with (3-aminopropyl) triethoxysilane (APTES), which reduces surface defects and enhances the photoluminescence quantum yield (PLQY) from 38.5% to 74.4%. Subsequently, a dense silica shell is constructed via in situ hydrolysis of tetramethyl orthosilicate (TMOS), further improving the PLQY to 95.6% and significantly boosting environmental stability. Structural and optical characterizations confirm effective defect passivation and suppress non-radiative recombination, with carrier lifetimes extended from 2.5 ns to 36.9 ns. Remarkably, the silica-coated PQDs retain over 50% of their initial emission intensity after 100 min of water immersion, far exceeding the stability of uncoated counterparts. Furthermore, when integrated with a commercial K₂SiF₆: Mn⁴⁺ red phosphor and a blue light-emitting diode (LED) chip, the resulting white LED (WLED) exhibits a wide color gamut covering 104% of the National Television System Committee (NTSC) standard and Commission Internationale de l’Éclairage (CIE) coordinates of (0.323, 0.331), closely matching standard white light. Importantly, only the silica-coated PQDs maintain a stable electrically driven device emission spectrum after water exposure. Full article

Hyperspectral imaging (HSI) is a noncontact camera-based technique that enables deep learning models to learn various plant conditions by detecting light reflectance under illumination. In this study, we investigated the effects of four light sources—halogen (HAL), incandescent (INC), fluorescent (FLU), and light-emitting diodes (LED)—on the quality of spectral images and the vase life (VL) of cut roses, which are vulnerable to abiotic stresses. Cut roses ‘All For Love’ and ‘White Beauty’ were used to compare cultivar-specific visible reflectance characteristics associated with contrasting petal pigmentation. HSI was performed at four time points, yielding 640 images per light source from 40 cut roses. The results revealed that the light source strongly affected both the image quality (mAP@0.5 60–80%) and VL (0–3 d) of cut roses. The HAL lamp produced high-quality spectral images across wavelengths (WL) ranging from 480 to 900 nm and yielded the highest object detection performance (ODP), reaching mAP@0.5 of 85% in ‘All For Love’ and 83% in ‘White Beauty’ with the YOLOv11x models. However, it increased petal temperature by 2.7–3 °C, thereby stimulating leaf transpiration and consequently shortening the VL of the flowers by 1–2.5 d. In contrast, INC produced unclear images with low spectral signals throughout the WL and consequently resulted in lower ODP, with mAP@0.5 of 74% and 69% in ‘All For Love’ and ‘White Beauty’, respectively. The INC only slightly increased petal temperature (1.2–1.3 °C) and shortened the VL by 1 d in the both cultivars. Although FLU and LED had only minor effects on petal temperature and VL, these illuminations generated transient spectral peaks in the WL range of 480–620 nm, resulting in decreased ODP (mAP@0.5 60–75%). Our results revealed that HAL provided reliable, high-quality spectral image data and high object detection accuracy, but simultaneously had negative effects on flower quality. Our findings suggest an alternative two-phase approach for illumination applications that uses HAL during the initial exploration of spectra corresponding to specific symptoms of interest, followed by LED for routine plant monitoring. Optimizing illumination in HSI will improve the accuracy of deep learning-based prediction and thereby contribute to the development of an automated quality sorting system that is urgently required in the cut flower industry. Full article

The poor stability of CsPbBr₃ perovskite nanocrystals (PNCs) caused by weak and dynamic ligand coordination severely limits their commercial applications. Herein, a dual-ligand synergistic modification strategy based on bromocarboxylic acids (BCAs) and oleylamine (OAm) was developed to mediate the surface structures and luminescent dynamics of CsPbBr₃ PNCs. The results reveal that carboxylate groups of BCA ligands modulate crystal growth, while its terminal Br atom forms a strong coordination with exposed Pb²⁺ on the PNCs surface, which can effectively passivate lead- and bromine-related defects. The synergistic protection of OAm ligands enhances the stability of PNCs via amino-halide electrostatic interactions and steric hindrance effects. Notably, based on the relatively dense surface coating of 4-bromobutyric acid (BBA) and OAm dual-ligands, the prepared CsPbBr₃ PNCs exhibit a high photoluminescence quantum yield (PLQY) of 85.2 ± 2.4% and remarkable storage stability, retaining 90.2 ± 1.7% of their initial PL intensity after being stored for 63 days under ambient conditions. Furthermore, a prototype white light-emitting diode (WLED) fabricated with these PNCs displays a wide color gamut covering 122.1% of the NTSC standard and a luminous efficacy of 64.6 lm/W. This work provides a facile and feasible ligand engineering strategy to obtain highly stable and emissive PNCs. Full article

Organic light-emitting diodes (OLEDs) have the advantages of high efficiency and high color purity, which gives them great potential and application prospects in the field of display technology, and thus they have been of wide interest for scholars and industry. Due to their nature, when using the first generation of fluorescent materials, only 25% of the excitons are used, while the rest are wasted, meaning the device efficiency does not exceed 25%. The second generation of phosphorescent materials solves this problem by utilizing 25% singlet excitons while utilizing 75% triplet excitons, achieving 100% internal quantum efficiency. Therefore, a third generation of materials, namely Thermally Activated Delayed Fluorescence (TADF) materials, has been developed, and these are able to use the small singlet–triplet energy gap to allow excitons on the triplet state to upconvert back to the single state, which improves the utilization of triplet excitons. These TADF materials can also reach 100% maximum internal quantum efficiency, but they have many problems, such as low color purity and serious efficiency roll-off. Therefore, researchers have designed hyperfluorescent materials, which possess high efficiency, high color purity, and a long lifetime, showing tremendous potential and application prospects in the field of display technology. This report takes hyperfluorescent OLEDs as the entry point and the molecular design and luminescence mechanism of hyperfluorescent materials are reviewed, considering blue, green, red, and white light. Full article

White organic light-emitting diodes (OLEDs) offer a promising solution for next-generation lighting technologies and their ability to emit white light through various mechanisms make them an attractive option for illumination and display applications. Here, we design and prepare a series of N,N-difluorenevinylaniline-based small molecules and polymer, and realize white OLEDs based on these luminescent materials with combined blue monomer emission and orange electromer emission upon electronic excitation in the solution-processed devices. Impressively, the single-component nonconjugated polymer exhibits the best device performance, because the nonconjugated structure favors good solubility of the polymers, while the conjugated starburst unit functions as highly luminescent fluorophore in both single molecular and aggregated structures for the blue and orange emissions, respectively. Specifically, the non-doped solution-processed OLEDs achieve warm white electroluminescence with a maximum luminance of 1806 cd/m² and a maximum external quantum efficiency of 2.63%. And, the OLEDs based on the monomer also exhibit white electroluminescence with Commission Internationale de L’Eclairage coordinates of (0.30, 0.32). These results highlight a promising strategy for the material design and preparation of single-component nonconjugated polymers with rich emissive behaviors in solid states towards efficient and solution-processable white OLEDs. Full article

Mn⁴⁺-activated fluoride phosphors possess outstanding luminescent properties, making them highly suitable for applications in lighting and display technologies. However, the synthesis of such phosphors generally requires the use of large amounts of highly toxic aqueous HF, leading to serious environmental pollution. To eliminate the use of hazardous HF solution, a low-temperature molten salt method employing NH₄HF₂ was developed to synthesize the narrow-band red emitter Cs₂GeF₆: Mn⁴⁺ phosphor. Following the reaction, the product was washed with a dilute H₂O₂ solution to remove residual NH₄HF₂ and other impurities. The phase purity and morphology were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively, and the luminescence properties were examined via photoluminescence (PL) spectroscopy. The obtained phosphors exhibit bright red emission characteristics of Mn⁴⁺ under blue-violet excitation. Among them, Cs₂GeF₆: 0.08 Mn⁴⁺ shows the highest emission intensity, with an internal quantum efficiency (IQE) of 78%. A white light-emitting diode (WLED) fabricated by combining this phosphor with a blue chip and commercial Y₃Al₅O₁₂: Ce³⁺ (YAG) phosphor achieved a high luminous efficacy (LE) of ~146 lm/W, a correlated color temperature (CCT) of ~4396 K, and a color rendering index (Ra) of ~83, alongside excellent operational color stability. Full article

Tandem white organic light-emitting diodes (OLEDs), formed by stacking red, green, and blue organic electroluminescent units, offer a promising route toward high-resolution microdisplays. However, their performance is constrained by the intrinsically short lifetime of blue OLED sub-units. Replacing the unstable blue OLED with a long-lived GaN-based LED could address this limitation, but practical hybridization remains difficult because of incompatible fabrication routes and significant current imbalance between the inorganic and organic units. Here, we demonstrate the first hybrid GaN–OLED tandem white LEDs enabled by an interface-engineered charge-generation unit (CGU). By introducing an ITO/HAT-CN/LiNH₂-doped Bphen CGU, we simultaneously enhance the work function, strengthen the built-in electric field, and smooth the interfacial morphology. These synergistic effects promote efficient charge generation, yielding near-ideal voltage summation and well-balanced electron–hole injection. As a result, the hybrid tandem device shows a nearly twofold increase in current efficiency (from 28.1 to 58.6 cd A^–1) and significantly reduced spectral shift under varying current densities. We further demonstrate the generality of this approach by integrating the GaN emission with yellow OLEDs to produce stable blue–yellow hybrid white emission. This work establishes an applicable strategy for integrating GaN-LEDs and OLEDs, opening a pathway toward efficient, stable, and compact white light engines for next-generation microdisplay technologies. Full article

An efficient method for evaluating the spectral irradiance properties of the white light of white LEDs is conducted. The method includes two main steps. The first step is to build up spectral irradiance modeling for the blue and yellow emission bands. The photometric parameter of the spectral irradiance of white light which is generated by yellow and blue light mixing is determined based on the photometry and colorimetry theories. The correlated color temperature value strongly depends on the power ratios of blue and yellow light. In addition, the result indicates that the emission bandwidth of yellow phosphor is also an important factor for increasing the color performance of output light. The selection of material with a broader bandwidth of yellow light can control a slower variation in color property compared to the case of using a material with a narrower bandwidth. In addition, the blue light hazard ratio of the spectral irradiance of white light can be extracted, which is helpful for designing the white light with moderate blue and yellow power ratios before fabricating the white LEDs product. Full article

Mn⁴⁺-doped fluoride red phosphors are widely used in white LED lighting and display applications due to their excellent luminescent properties. However, their synthesis relies heavily on highly toxic aqueous hydrofluoric acid, which not only causes severe environmental and soil/water pollution but also makes it difficult to control the microstructure of the products due to the rapid reaction rate. In this study, low-melting-point NH₄HF₂ was used as the molten salt, with KMnO₄ and MnF₂ as manganese sources, to synthesize the red phosphor K₃AlF₆: Mn⁴⁺ via the molten salt method. After the reaction, impurities such as NH₄HF₂ were removed by washing with a dilute H₂O₂ solution. The microstructure, photoluminescence properties, thermal quenching behavior, and application in warm white light-emitting diodes (W-LEDs) of the K₃AlF₆: Mn⁴⁺ phosphors were investigated. The results indicate that the phosphors prepared by this method consist of a single pure phase. By adjusting the molten salt content, the morphology of the product can be transformed from nanoparticle-like to nanorod-like structures. All products exhibit the characteristic red emission of Mn⁴⁺ under blue and violet light excitation, with the optimally doped sample achieving an internal quantum efficiency (IQE) of 69% under blue light excitation. The combination of the obtained K₃AlF₆: Mn⁴⁺ with the yellow phosphor YAG enabled the fabrication of W-LEDs. These W-LEDs achieved a color rendering index (Ra) of 86.8, a luminous efficacy (LE) of 77 lm/W, and a correlated color temperature (CCT) of 3690 K, along with excellent color stability under operating conditions. Full article

Quantum dots (QDs) have tremendous potential for next-generation displays due to their high color purity, photoluminescence efficiency, and power efficiency. In this work, we present a simple and cost-effective method for fabricating flexible single- and multiple-layer films, and they can be detached and attached to the outside of OLEDs as a light-scattering and color-conversion layer. Light extraction efficiency is enhanced by forming low-density structures by using the reactive ion etching (RIE) process. As a result, the QD/PDMS composite film allowed for color conversion and achieved an excellent light extraction efficiency of up to 9.2%. Furthermore, the QD/PDMS composite film and greenish-blue OLED produced white light (CIEx,y = 0.28, 0.41), demonstrating the potential for application in broad areas, from flexible displays to lighting. The method provides a simple and cost-effective alternative to conventional processes. Full article

Thermal stability is a crucial factor in evaluating phosphors and determining whether they can be utilized in white light emitting diodes (w-LEDs). In this work, a series of Sr₆LuAl(BO₃)₆: Dy³⁺ (SLAB:Dy³⁺) phosphors was synthesized via high-temperature solid-state reaction. The synthesized SLAB:Dy³⁺ phosphor exhibits narrow-band emission in the range of 450–700 nm under 348 nm UV excitation. The strongest emission peak is located at 577 nm and is primarily due to ⁴F_9/2-⁶H_13/2 electron transitions. The optimal doping concentration of Dy³⁺ in the synthesized phosphor was 15 mol%. The integrated emission intensity of the synthesized phosphor at 480 k is 97.84% of that at 300 k, with excellent thermal stability. The activation energy E_g = 0.62 eV. Meanwhile, the Commission International de l’Eclairage (CIE) coordinates of the prepared w-LEDs were (0.309,0.363) with a correlated color temperature (CCT) of 6497 K. Preliminary experimental findings suggest that SLAB:Dy³⁺ phosphors hold promise for utilization in w-LEDs applications. Full article

The genus Corydalis, belonging to the Papaveraceae family, is widely distributed across the Northern Hemisphere, primarily in Asia. This study aimed to investigate the effect of plant growth regulators (PGRs) on callus induction, and of light quality and intensity on indirect shoot organogenesis, dl-Tetrahydropalmatine (dl-THP) accumulation, and activities of antioxidant enzymes in Corydalis turtschaninovii Besser. Calli were successfully induced from the leaf, tuber, and petiole explants with different PGR combinations. The best callus induction from leaf, tuber, and petiole explants were obtained in the medium supplemented with 3 mg·L⁻¹ kinetin (Kn) combined with 0.8 mg·L⁻¹ naphthalene acetic acid (NAA), 3 mg·L⁻¹ benzyl adenine (BA) combined with 0.8 mg·L⁻¹ NAA, and 2 mg·L⁻¹ BA combined with 0.5 mg·L⁻¹ NAA, respectively. For indirect shoot organogenesis, calli were cultured on the Murashige and Skoog (MS) medium under dark (D), white (W), red (R), blue (B), or 1:1 mixture of red and blue (RB) light-emitting diodes (LEDs) at an intensity of 25 or 50 µmol·m⁻²·s⁻¹ photosynthetic photon flux density (PPFD) for six weeks. The RB treatment increased biomass accumulation of the callus, and promoted the induction of the shoot from the callus, whereas the R treatment promoted the dl-THP accumulation, especially with the higher light intensity. Light quality and intensity significantly influenced the activities of antioxidant enzymes and the 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical scavenging capacity in calli, with the most pronounced effects observed under B or RB light treatments. Taken together, the application of monochromatic LED or combinations of red and blue LEDs could be used for the callus culture for different purposes in vitro. Full article

Background/Objective: The effectiveness of blue-light phototherapy (PT) is mainly dependent on the total dose of light (time under PT and amount of skin exposed) received by infants. The primary aim of this study was the development of a novel, flexible, and stretchable device to provide continuous PT treatment, avoiding temporary interruptions that are often observed in practice, such as during breastfeeding, for example. This study evaluated the biocompatibility of a novel, low-cost blanket equipped with light-emitting diode (LED) lamps designed to maintain therapeutic efficacy while facilitating uninterrupted skin-to-skin contact. Methods: Fourteen New Zealand White rabbits, weighing approximately 2.9 kg and aged 4 months, were randomly assigned to an experimental group (TG, n = 7) or a control group (CG, n = 7). The TG received phototherapy directly on the skin (irradiance: 19.3 [13.0–22.0] µW/cm⁻²/nm⁻¹) during two 12 h sessions over consecutive days, while the CG remained under identical conditions with the device turned off. Biochemical, hematological, dermatological, and histological parameters, as well as rectal and skin temperatures, were assessed. Results: The results showed no differences in clinical appearance or histological analysis of skin tissue between the groups. Blood analysis indicated a reduction in absolute monocyte counts in the TG compared to the CG (p = 0.049), though levels remained within normal ranges. Skin temperature was consistently higher in the TG, except during the initial measurement. Rectal temperatures were similar on the first day but lower in the TG on the second day (mean 40.3 ± 0.21 °C vs. 40.7 ± 0.32 °C; p = 0.039). Conclusions: Temperature levels remained within physiological limits for both groups throughout the study. The device demonstrated biocompatibility and caused no adverse dermatological, hematological, or biochemical effects. Full article

The orange mullein is a biennial plant whose tall yellow flower spikes contain mucilage, saponins, and other medicinal compounds that have a beneficial effect on respiratory problems. As light quality is known to influence plant morphology and physiology, with effects often depending on the species, understanding these responses in mullein is of particular interest. Therefore, this study aimed to investigate the combined effects of different light-emitting diodes (white, red and blue) and their corresponding photon flux densities (PPFD) on the morphology, pigment composition, antioxidant activity, fluorescence parameters and OJIP transient curves in mullein (Verbascum phlomoides L.) seedlings. Seedlings grown under blue light, which had relatively higher PPFD, showed the greatest root length, leaf number, leaf and root fresh and dry biomass. Red light, with lower PPFD, resulted in the lowest values for these parameters. Compared to white light, pigment analysis showed that blue light increased chlorophyll a, total chlorophyll, carotenoid content, and the Chl a/b ratio. Also, blue light enhanced antioxidant activity, as well as the accumulation of phenolic compounds and flavonoids, indicating that it appeared to enhance the synthesis of secondary metabolites under this spectrum. In contrast, seedlings under red light exhibited the lowest ferric reducing antioxidant power values and tended to reduce levels of phenols and flavonoids, indicating a weaker antioxidative response. It was found that white light appeared to enhance the photochemical activity of photosystem II (PSII) and energy dissipation. Blue light improved linear electron transport, photosystem I (PSI) activity and overall photosynthetic performance. Red light preferentially increased electron flow towards the final acceptors of PSI, affecting the terminal part of the electron transport chain. Analysis of OJIP curves revealed spectrum and intensity-specific changes in the L, K, H, and G bands, demonstrating that light treatments with differing PPFDs selectively modulate PSII and PSI function. Full article

Canada goldenrod (Solidago canadensis L.), a short-day plant commonly cultivated as a cut flower, depends on proper lighting management to obtain long stems and higher commercial value. Thus, this study aimed to determine the effect of modifying the light spectrum through the installation of light-emitting diodes (LEDs) and the use of colored shade nets on the production and quality of Canada goldenrod stems. The treatments used were colored shade nets and different LED lighting treatments. Production per plant and productivity per square meter were determined. Twenty stems were selected and evaluated for: stem length; inflorescence length and width; number of floral ramets per inflorescence; number of leaves; stem base diameter (mm); and fresh stem biomass (g). Canada goldenrod plants require an extension of the light period with artificial lighting to produce higher-quality stems, regardless of whether the bulbs emit red or white light. The use of nets with 50% red and white shading promoted higher production and elongation of Canada goldenrod stems, with a production that reached up to 4.2 floral stems per plant and 100.3 floral stems per square meter using the red shade net and white LED. These floral stems were of high commercial standard, with a length of up to 81.35 cm with the red shade net and red LED, and were 31 cm in diameter for the inflorescences, approximately, under black or white shade nets and white or red LEDs. More robust floral stems with greater biomass were observed using any shade net color and LED lamps. Full article