Search Results (358)

Carbon nanotube (CNT) coatings show excellent tribological properties but face challenges in dispersion and industrial application. This study investigated TiO₂ nanoparticle incorporation effects on CNT coating tribological performance. CNT/TiO₂ composite coatings with varying TiO₂ content (0.5–2.0 wt.%) were fabricated on SUS 304 substrates via spin coating. Surface morphology, roughness, wettability, and tribological properties were characterized using confocal microscopy, SEM, Raman spectroscopy, and reciprocating friction tests. Results showed that low TiO₂ concentrations (0.5–0.7 wt.%) achieved optimal performance. The C3-Ti0.5 specimen maintained substrate-level smoothness (Ra = 0.09 μm) while preserving coating integrity. Raman analysis confirmed structural preservation of CNTs (ID/IG ≈ 1.0) across all formulations. Tribologically, C3-Ti0.5 exhibited a friction coefficient of 0.099, approaching pure CNT coating performance (0.090), with a wear rate of 9.00 × 10⁻⁷ mm³/N·mm. Higher TiO₂ concentrations progressively degraded performance, with C3-Ti2 showing increased friction (0.263) and wear rate (2.87 × 10⁻⁶ mm³/N·mm). The 0.5–0.7 wt.% TiO₂ range represents optimal composition for applications requiring both smooth surface finish and superior tribological performance, particularly for precision mechanical components where surface quality and friction control are equally critical. Full article

This study examined the effects of dielectric barrier discharge (DBD) plasma and copper oxide nanoparticles (CuO NPs) on rice seed quality, seedling growth, and fungal inhibition. Sanpatong 1 rice seeds were treated with DBD plasma at three exposure durations (0.4, 0.6, and 0.8 s/cm) and coated with CuO NP solutions at five concentrations (0, 0.02, 0.04, 0.06, and 0.08 M). The experiment followed a split-split-plot design within a randomized complete block design (RCBD), with storage time (0, 2, 4, and 6 months) as the main plot factor. Plasma etching improved seed surface wettability, while CuO NPs increased copper uptake and promoted growth at 0.04–0.06 M but caused toxicity at 0.08 M. Combined treatments suppressed Rhizopus sp. and Rhizoctonia solani, though Aspergillus spp. were less affected. Seed quality declined after six months of storage, likely due to oxidative stress. The best results were obtained with 0.6 s/cm plasma and 0.06 M CuO NPs, maximizing germination, vigor, and seedling growth without toxicity, demonstrating their potential as practical tools for improving rice seed quality and pathogen management. Full article

Ophthalmic lens coatings are increasingly designed to combine optical, mechanical, and biological functions. This systematic review, registered in PROSPERO and conducted according to PRISMA 2020 guidelines, synthesized 54 experimental, preclinical, and clinical studies on coatings for spectacle lenses, contact lenses, and intraocular lenses. Spectacle lens studies consistently showed that anti-reflective and blue-light filtering coatings reduce glare perception, improve contrast sensitivity, and provide UV protection, while laboratory tests demonstrated significant reductions in impact resistance, with fracture energy of CR-39 lenses decreasing by up to 63% when coated. Contact lens research revealed that plasma and polymeric coatings reduce water contact angles from >100° to <20°, enhancing wettability, while antimicrobial strategies such as melamine binding or nanoparticle-based films achieved >80% reductions in bacterial adhesion. Drug-eluting approaches sustained antibiotic or antioxidant release for periods ranging from 24 h to 6 days, with improved ocular bioavailability compared with drops. Intraocular lens studies demonstrated that heparin surface modifications reduced postoperative flare and anterior chamber cells, and phosphorylcholine or alkylphosphocholine coatings suppressed lens epithelial cell proliferation. Drug-loaded coatings with methotrexate, gefitinib, or amikacin significantly inhibited posterior capsule opacification and infection in ex vivo and animal models. Collectively, coatings improve visual comfort, photoprotection, wettability, and biocompatibility, but clinical translation requires solutions to mechanical trade-offs, long-term stability, and regulatory challenges. Full article

This review presents recent advancements in cold atmospheric pressure (AP) plasma (CAP) processes for the synthesis and surface treatment of polymer films and metal nanoparticles (NPs) in biomedical applications. We discuss the properties and applications of atmospheric pressure plasma (APP) processes, including dielectric barrier discharge (DBD) and plasma jet methods, highlighting their effectiveness in controlling surface characteristics such as wettability and functionalization. Full article

Surface-enhanced Raman spectroscopy (SERS) enables ultra-sensitive molecular detection and has broad analytical and biomedical applications; recent advances focus on high-performance substrates and innovative detection strategies. However, achieving controllable and reproducible substrate fabrication—particularly using natural templates such as hair—remains challenging, limiting SERS application in trace analysis and on-site detection. This study developed a single-hair in situ SERS platform using a natural hair template. Confinement within hair cuticle grooves and capillary-evaporation assembly enables dense arrangement of cetyltrimethylammonium bromide-coated Au nanorods and polyvinylpyrrolidone-coated Au nanoparticles, forming uniform plasmonic nanoarrays. Spectroscopy and microscopy analyses confirmed the regular alignment of nanostructures along the hair axis with denser packing at the edges. The platform detected crystal violet at 10⁻⁹ M, yielding clear signals, negligible background, and stable peaks after repeated washing. For p-phenylenediamine, enhancement was observed down to 10⁻⁶ M. On the platform, a concentration-dependent response appeared within 10⁻³–10⁻⁵ M, with spatial Raman imaging along the hair axis. Capillary-evaporation coupling and interfacial wettability facilitated solute enrichment from larger to smaller gap hotspots, improving signal-to-noise ratio and reproducibility. This portable, low-cost, and scalable method supports rapid on-site screening in complex matrixes, offering a general strategy for hotspot engineering and programmable assembly on natural templates. Full article

In this study, a highly stable light-responsive superhydrophobic paper was successfully fabricated. The process involved polymerizing the synthesized light-responsive monomer PAPAE with the hydrophilic monomer 2-hydroxyethyl methacrylate(HEMA), the fluorine-containing monomer hexafluorobutyl methacrylate(HFMA),and 3-trimethoxysilyl-propyl methacrylate(TSPM), followed by grafting (3-Aminopropyl) triethoxysilane (APTES)-modified SiO₂ nanoparticles onto the polymer to enhance surface roughness, and subsequently applying this composite to the paper surface. When the monomer ratio in the polymer was HFMA:TSPM:PAPAE:HEMA = 0.2:0.2:0.4:0.2, the resulting coating exhibited good water solubility, enabling the modified paper to achieve reversible wettability transitions under light irradiation. At a SiO₂-to-polymer ratio of 0.3, the contact angle variation range reached its maximum (96–156.8°). The proposed method for fabricating superhydrophobic paper not only offers relative simplicity, low cost, and strong versatility but also imparts the paper with excellent weather resistance, abrasion resistance, and ultrasonic durability, highlighting its great potential for practical applications. Full article

This work presents the design and fabrication of microstructured hydrophobic surfaces via fused filament fabrication (FFF) 3D printing with polylactic acid (PLA). Three geometric patterns—triangular-based prisms (TG), truncated pyramids (TP), and truncated ellipsoidal cones (CET)—were developed to modify the surface wettability. Morphological analysis revealed that the printer resolution limits the accurate reproduction of sharp CAD-defined features. Despite this, TG structures exhibited superhydrophobic behavior evaluated through static water contact angles (WCAs), reaching up to 164° along the structured direction and so representing a 100% increase relative to flat PLA surfaces (WCA = 82°). To improve print fidelity, TP and CET geometries with enlarged features were introduced, resulting in contact angles up to 128°, corresponding to a 56% increase in hydrophobicity. The truncated shapes enable the fabrication of the smallest features achievable via the FFF technique, while maintaining good resolution and obtaining higher contact angles. In addition, surface functionalization with fluoropolymer-coated SiO₂ nanoparticles, confirmed by SEM and Raman spectroscopy, led to a further slight enhancement in wettability up to 18% on the structured surfaces. These findings highlight the potential of FFF-based microstructuring, combined with surface treatments, for tailoring the wetting properties of 3D-printed polymeric parts with promising applications in self-cleaning, de-icing, and anti-wetting surfaces. Full article

This study evaluated a biomimetic filler strategy for two-step universal dental adhesives by integrating amine-functionalized mesoporous silica nanoparticles (MSNs) loaded with polyacrylic acid-stabilized amorphous calcium phosphate (PA–ACP) into the primer phase. MSNs were synthesized and characterized by FTIR, N₂ sorption (BET), and HRTEM to confirm structural integrity and effective PA–ACP loading. Two commercial adhesives (G2 Bond and OptiBond eXTRa) were modified by incorporating different volumes fractions (10, 15, 20 vol%) of PA–ACP/MSN. Wettability (contact angle), microtensile bond strength (μTBS), and cytotoxicity (indirect MTT assay using human periodontal ligament fibroblasts, HPLFs) were assessed. The results demonstrated that incorporating up to 15 vol% PA–ACP/MSN maintained favorable wettability and bond strength, comparable to those of the unmodified controls. At 20 vol%, significant increases in contact angles and reductions in bond strength indicated impaired primer infiltration. Cytotoxicity testing confirmed high fibroblast viability (>70%) across all tested concentrations, verifying the biocompatibility of PA–ACP/MSN-filled primers. This work confirms the feasibility of a biomimetic adhesive design using PA–ACP/MSN in the primer phase without compromising immediate wettability and immediate μTBS up to 15 vol%. Remineralization is a potential capability that requires verification in future studies. Full article

This study investigates the surface properties of bio-based unsaturated polyester resin (b-UPR) nanocomposites reinforced with biosilica nanoparticles derived from rice husk. The b-UPR matrix was synthesized from recycled polyethylene terephthalate (PET) and renewable monomers, providing a sustainable alternative to conventional polyester resins. Unmodified and modified biosilica particles with silanes: (3-trimethoxysilylpropyl methacrylate—MEMO, trimethoxyvinylsilane—VYNIL, and 3-aminopropyltrimethoxysilane with biodiesel—AMBD) were incorporated in different amounts to evaluate their influence on the wettability, topography, and viscoelastic behavior of the composites. Contact angle measurements revealed that the addition of modified biosilica significantly improved the hydrophobicity of the b-UPR surface. The greatest increase in the wetting angle, amounting to 79.9% compared to composites with unmodified silica, was observed in the composites containing 5 wt.% SiO₂-AMBD. Atomic force microscopy (AFM) analysis indicated enhanced surface roughness and uniform dispersion of the nanoparticles. For the composite containing 1 wt.% of silica particles, the surface roughness increased by 25.5% with the AMBD modification and by 84.2% with the MEMO modification, compared to the unmodified system. Creep testing demonstrated that the reinforced nanocomposites exhibited improved dimensional stability under sustained load compared to the neat resin. These findings confirm that the integration of surface-modified biosilica not only enhances the mechanical properties but also optimizes the surface characteristics of bio-based polyester composites, broadening their potential for high-performance and sustainable applications. Full article

Waterflooding, a key method for secondary hydrocarbon recovery, has been employed since the early 20th century. Over time, the role of water chemistry and ions in recovery has been studied extensively. Low-salinity water (LSW) injection, a common technique since the 1930s, improves oil recovery by altering the wettability of reservoir rocks and reducing residual oil saturation. Recent developments emphasize the integration of LSW with various recovery methods such as CO₂ injections, surfactants, alkali, polymers, and nanoparticles (NPs). This article offers a comprehensive perspective on how LSW injection is combined with these enhanced oil recovery (EOR) techniques, with a focus on improving oil displacement and recovery efficiency. Surfactants enhance the effectiveness of LSW by lowering interfacial tension (IFT) and improving wettability, while ASP flooding helps reduce surfactant loss and promotes in situ soap formation. Polymer injections boost oil recovery by increasing fluid viscosity and improving sweep efficiency. Nevertheless, challenges such as fine migration and unstable flow persist, requiring additional optimization. The combination of LSW with nanoparticles has shown potential in modifying wettability, adjusting viscosity, and stabilizing emulsions through careful concentration management to prevent or reduce formation damage. Finally, building on discussions around the underlying mechanisms involved in improved oil recovery and the challenges associated with each approach, this article highlights their prospects for future research and field implementation. By combining LSW with advanced EOR techniques, the oil industry can improve recovery efficiency while addressing both environmental and operational challenges. Full article

The objective of this study was to investigate the physicochemical properties of hybrid coatings with titanium nitride and boron nitride nanoparticles deposited on the TiAlV medical alloy via the sol–gel process. The developed layers were intended to impart bactericidal properties and provide protection against surgical abrasions during the implantation procedure. This study focused on evaluating the microstructure (SEM + EDS), structure (XRD, FTIR), and surface properties, including wettability, surface free energy, and roughness of the synthesized layers. Our results confirmed that it was feasible to produce hybrid layers with various microstructures and diverse layer morphologies. The FTIR and XRD structural analyses confirmed the presence of an organosilicon matrix incorporating the two aforementioned types of ceramic particles. Full article

In this work, polypropylene (PP) melt-blown nonwoven fabric was used as a raw material, which was plasma-treated and grafted with HBP/Ag nanoparticle (NP) solution. The surface wettability, surface morphology, and surface element composition after the treatment were evaluated through a contact angle test, field emission scanning electron microscopy (FE-SEM), energy-dispersive spectrometer (EDS), and Fourier transform infrared spectroscopy (FTIR), respectively. The antibacterial activity of PP fabrics treated with Ag NPs against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) was measured. SEM and EDS results showed that Ag NPs were evenly dispersed on the surface of the PP fabrics. The PP fabrics treated with Ag NPs exhibited excellent antibacterial performance. Full article

Electrospun nanofibrous membranes have gained considerable attention in bone tissue engineering due to their ability to mimic the extracellular matrix and provide a suitable environment for cell attachment and proliferation. This study investigates the fabrication, characterization, and biocompatibility of poly(L-lactic acid) (PLA)-based membranes enhanced with periclase (MgO) and gold nanoparticles (AuNPs). The membranes were fabricated using an optimized electrospinning process and subsequently characterized using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), Fourier-transform infrared spectroscopy (FT-IR), and contact angle measurements. Additionally, in vitro biodegradation studies in simulated body fluid (SBF) and cytocompatibility tests with osteoblast-like cells were conducted. The results demonstrated that the incorporation of MgO and AuNPs significantly influenced the structural and chemical properties of the membranes, improving their wettability and bioactivity. SEM imaging confirmed uniform fiber morphology with well-distributed nanoparticles. FT-IR spectroscopy indicated successful integration of bioactive components into the PLA matrix. Cytocompatibility assays showed that modified membranes promoted higher osteoblast adhesion and proliferation compared to pristine PLA membranes. Furthermore, biodegradation studies revealed a controlled degradation rate suitable for guided bone regeneration applications. These findings suggest that electrospun PLA membranes enriched with MgO and AuNPs present a promising biomaterial for GBR applications, offering improved bioactivity, mechanical stability, and biocompatibility. Full article

Ice accumulation on exposed surfaces presents substantial economic and safety challenges across various industries. To overcome limitations associated with traditional anti-icing methods, such as the use of nanoparticles, this study introduces a novel and facile approach for fabricating superhydrophobic and anti-icing microstructures using cost-effective LCD 3D printing technology. The influence of diverse pillar geometries, including square, cylindrical, hexagonal, and truncated conical forms, was analyzed to assess their effects on the hydrophobic and anti-icing/icephobic performance in terms of wettability, ice adhesion strength, and icing delay time. The role of microstructure topography was further investigated through cylindrical patterns with varying geometric parameters to identify optimal designs for enhancing hydrophobic and icephobic characteristics. Furthermore, the effectiveness of surface functionalization using a low surface energy material was evaluated. Our findings demonstrate that the synergistic combination of tailored microscale geometries and surface functionalization significantly enhances anti-icing performance with reliable repeatability, achieving ice adhesion of 13.9 and 17.9 kPa for square and cylindrical pillars, respectively. Critically, this nanoparticle-free 3D printing and low surface energy treatment method offers a scalable and efficient route for producing high-performance hydrophobic/icephobic surfaces, opening promising avenues for applications in sectors where robust anti-icing capabilities are crucial, such as renewable energy and transportation. Full article

The insulating rod of aramid fiber-reinforced epoxy resin composites (AFRP) is an important component of gas-insulated switchgear (GIS). Under complex working conditions, the high temperature caused by voltage, current, and external climate change becomes one of the important factors that aggravate the interface degradation between aramid fiber (AF) and epoxy resin (EP). In this paper, molecular dynamics (MD) simulation software is used to study the effect of temperature on the interfacial properties of AF/EP. At the same time, the mechanism of improving the interfacial properties of three nanoparticles with different properties (insulator Al₂O₃, semiconductor ZnO, and conductor carbon nanotube (CNT)) is explored. The results show that the increase in temperature will greatly reduce the interfacial van der Waals force, thereby reducing the interfacial binding energy between AF and EP, making the interfacial wettability worse. Furthermore, the addition of the three fillers can improve the interfacial adhesion of the composite material. Among them, Al₂O₃ and CNT maintain a large dipole moment at high temperature, making the van der Waals force more stable and the adhesion performance attenuation less. The Mulliken charge and energy gap of Al₂O₃ and ZnO decrease slightly with temperature but are still higher than AF, which is conducive to maintaining good interfacial insulation performance. Full article