Search Results (1,033)

Rapid screening of foodborne pathogens is critical for food safety, yet current detection techniques often suffer from low efficiency and complexity. In this study, we developed a sliding microfluidic colorimetric biosensor for the fast, sensitive, and multiplex detection of Salmonella. First, the target bacteria were specifically captured by antibody-functionalized magnetic nanoparticles in the microfluidic chip, forming magnetic bead–bacteria complexes. Then, through motor-assisted sliding of the chip, manganese dioxide (MnO₂) nanoflowers conjugated with secondary antibodies were introduced to bind the captured bacteria, generating a dual-antibody sandwich structure. Finally, a second sliding step brought the complexes into contact with a chromogenic substrate, where the MnO₂ nanoflowers catalyzed a colorimetric reaction, and the resulting signal was used to quantify the Salmonella concentration. Under optimized conditions, the biosensor achieved a detection limit of 10 CFU/mL within 20 min. In spiked pork samples, the average recovery rate of Salmonella ranged from 94.9% to 125.4%, with a coefficient of variation between 4.0% and 6.8%. By integrating mixing, separation, washing, catalysis, and detection into a single chip, this microfluidic biosensor offers a user-friendly, time-efficient, and highly sensitive platform, showing great potential for the on-site detection of foodborne pathogens. Full article

Deep drilling and horizontal wells, as important means of unconventional oil and gas development, face problems with the high energy consumption but low removal efficiency of traditional well washing equipment, the uneven cleaning of horizontal well intervals, and an insufficient degree of automation. This paper proposes a novel hydraulic drive well washing device which consists of two main units. The wellbore cleaning unit comprises a hydraulic drive cutting–flushing module, a well cleaning mode-switching module, and a filter storage module. The unit uses hydraulic and mechanical forces to perform combined cleaning to prevent mud and sand from settling. By controlling the flow direction of the well washing fluid, it can directly switch between normal and reverse washing modes in the downhole area, and at the same time, it can control the working state of corresponding modules. The assembly control unit includes the chain lifting module and the arm assembly module, which can lift and move the device through the chain structure, allow for the rapid assembly of equipment through the use of a mechanical arm, and protect the reliability of equipment through the use of a centering structure. The device converts some of the hydraulic power into mechanical force, effectively improving cleaning and plugging removal efficiency, prolonging the downhole continuous working time of equipment, reducing manual operation requirements, and comprehensively improving cleaning efficiency and energy utilization efficiency. Full article

A nanoparticle formulation was generated from distiller dried grains with solubles (DDGS), and its effect on the production of anthraquinones (AQs) was evaluated on Rubia tinctorum hairy roots. The DDGS material was washed with water and ethyl acetate to remove mainly the soluble organic/inorganic molecules and reduce the fat content, respectively, followed by an alkaline treatment to remove the polysaccharides. The resulting alkaline solutions were then lyophilized and redispersed in deionized water to generate a monodispersed nanoparticulate formulation (DDGS-NP) with a hydrodynamic diameter and zeta potential of 227 ± 42 nm and −53 ± 7 mV, respectively. The formulation demonstrated good colloidal stability over time, and sterilized DDGS-NPs maintained comparable physicochemical properties. The nanoparticles were enriched in protein fractions, unsaturated fatty acids, and orthophosphate anion components from DDGS, as determined by solid-state Nuclear Magnetic Resonance (NMR), X-ray photoelectron spectroscopy (XPS), organic elemental analysis (OEA), and inductively coupled plasma optical emission spectrometry (ICP-OES) techniques. The DDGS-NPs were tested at different concentrations on Rubia tinctorum hairy roots, in comparison to or in combination with methyl jasmonate (MeJ), for their capacity to induce the production of AQs. All DDGS-NP concentrations increased the production of specific AQs to 7.7 (100 mg L⁻¹), 7.8 (200 mg L⁻¹), and 9.3 µmol/gFW (500 mg L⁻¹), with an extracellular AQ accumulation of 18 µM for the highest DDGS-NP concentration, in comparison with the control hairy roots (~2 µM AQ). The plant growth was not affected at any of the tested nanoparticle concentrations. Interestingly, the combination of DDGS-NPs and MeJ resulted in the highest extracellular AQ accumulation in R. tinctorum root cultures. Full article

Trichogramma wasps are highly effective biological control agents, offering an environmentally sustainable solution for pest management through their parasitism of insect eggs. This study evaluates the parasitism performance of six Trichogramma species—T. dendrolimi, T. chilonis, T. leucaniae, T. ostriniae, T. japonicum, and T. pretiosum—on five treatments of Eri silkworm (ES) eggs, a potential alternative to the large eggs of Antheraea pernyi for mass rearing. The ES egg treatments included the following: manually extracted, unfertilized, and washed eggs (MUW); naturally laid, unfertilized, and washed eggs (NUW); naturally laid, unfertilized, and unwashed eggs (NUUW); naturally laid, fertilized, and washed eggs (NFW); and naturally laid, fertilized, and unwashed eggs (NFUW). The results demonstrate that all Trichogramma species, except T. japonicum, successfully parasitized ES eggs across all treatments. Notably, washed eggs consistently supported higher parasitism and emergence rates compared to unwashed eggs, while unfertilized eggs outperformed fertilized eggs in these metrics. Among the treatments, unfertilized and washed eggs (MUW and NUW) exhibited the shortest pre-emergence time and the highest number of emerged adults, with no significant differences in female progeny ratios across most species. A striking exception was T. dendrolimi, which showed a significantly higher female offspring ratio in the MUW treatment. These findings highlight that MUW eggs of ES are a highly suitable alternative host for the mass production of Trichogramma wasps. This study provides critical insights for optimizing host egg treatments to enhance the efficiency of Trichogramma-based biological control programs. Full article

Malondialdehyde (MDA), a mutagenic and carcinogenic compound, is widely studied in the meat industry and lipid peroxidation research due to its implications for food quality and safety. Current methods for quantifying MDA in solid tissues are labor-intensive, requiring multiple instruments and approximately two hours to complete. This study presents an ultrafast kinetic fluorogenic method for quantifying MDA in ground beef, utilizing 2-thiobarbituric acid (TBA) as a fluorogenic probe. The total assay time is significantly shortened to 6 min from sample preparation to data acquisition. The assay’s robustness against matrix interference was validated using sample volume variation and standard addition calibration methods. Additionally, the effects of ambient exposure to air, washing, and cooking on MDA content in raw ground beef were quantified. While both ambient exposure to air and cooking increased MDA levels, washing raw ground beef and decanting cooked ground beef broth effectively reduced MDA levels in the ground beef. This simple and rapid assay can be adopted both in food research and industry. Moreover, insights from our study on the relationship between ground beef treatment and MDA concentration will help consumers make informed decisions about ground beef handling and consumption to lower their intake of MDA. Full article

Fish kills are sudden mass mortalities that occur in freshwater and marine systems worldwide. Fish kill surveys are essential for assessing the ecological and economic impacts of fish kill events, but are often labor-intensive, time-consuming, and spatially limited. This study aims to address these challenges by exploring the application of unoccupied aerial systems (or drones) and deep learning techniques for coastal fish carcass detection. Seven flights were conducted using a DJI Phantom 4 RGB quadcopter to monitor three sites with different substrates (i.e., sand, rock, shored Sargassum). Orthomosaics generated from drone imagery were useful for detecting carcasses washed ashore, but not floating or submerged carcasses. Single shot multibox detection (SSD) with a ResNet50-based model demonstrated high detection accuracy, with a mean average precision (mAP) of 0.77 and a mean average recall (mAR) of 0.81. The model had slightly higher average precision (AP) when detecting large objects (>42.24 cm long, AP = 0.90) compared to small objects (≤14.08 cm long, AP = 0.77) because smaller objects are harder to recognize and require more contextual reasoning. The results suggest a strong potential future application of these tools for rapid fish kill response and automatic enumeration and characterization of fish carcasses. Full article

Hemotrophic mycoplasmas (HMs) are cell wall-less, small and uncultivable pathogens, which can cause infections in pigs with no to severe clinical signs and can contribute to significant economic losses in the pig industry. In addition to the known mechanical transmission routes of HMs (e.g., via blood-contaminated instruments or lesions from ranking fights), transmission to pigs by arthropod vectors such as Stomoxys calcitrans is being discussed. To date, there is scant available data concerning the transmission of HMs by stable flies. The objective of this study is to gain more data concerning the occurrence of HMs in Stomoxys calcitrans. Therefore, quantitative real-time PCR was conducted on different stable fly samples (surface washings and whole flies). We found Mycoplasma (M.) suis in 5.2% of crushed flies and 4.2% of fly wash solutions, and M. parvum was detected in 5.2% of flies and 9.4% of fly wash solutions. ‘Candidatus (Ca.) M. haemosuis’ was not detected in any sample. The mean bacterial loads were 2.0 × 10² M. suis/fly, 9.3 × 10² M. suis/fly wash solution and, for M. parvum, 2.4 × 10³ M. parvum/fly and 2.1 × 10³ M. parvum/fly wash solution. This molecular occurrence of porcine HMs in blood-sucking flies and reasonable bacterial loads in the two- to three-digit range demonstrate that these flies serve as mechanical vectors in stables and are, therefore, of epidemiological importance. Full article

Phosphorus Adsorption Media (PAM) is an emerging technology used to remove phosphorus from water and has the advantage of minimal operation and maintenance support when compared to biological and chemical treatments. Although the capacity of PAM has been researched, the understanding of important design parameters for PAM is lacking. Therefore, this study focused on determining critical design parameters for PAM, such as hydraulic loading, Empty Bed Contact Time (EBCT), and its impact on the media’s capacity. In addition, the regeneration potential of PAM and the mathematical model for predicting the exhaustion of PAM are discussed to provide a practice tool for designing PAM. The results indicate that hydraulic loadings do not show a strong effect on PAM performance, as there are no significant differences between hydraulic loadings of 0.05, 0.12, and 0.22 mL/min/cm². This study also showed that the higher EBCT (190 min) has higher removal rates than the lower EBCT (60 and 90 min). This indicated that EBCT is a critical design parameter for PAM. Laboratory studies demonstrating the regeneration of exhausted media by washing with a caustic solution have been conducted, and a qualitative study showed that exhausted media can be used in hydroponics. Batch testing showed that over 99% of the sorbed phosphorus was eliminated after six cycles of the regeneration process. Full article

This study proposes a method for separating asphalt and aggregates in recycled asphalt pavement (RAP) materials using surfactants as solvents. This method utilizes surfactants to soften the asphalt by reducing its surface tension, separating the RAP clusters, and washing away the asphalt from the RAP. The wastewater is recycled during the emulsification–separation process without discharge. Factors affecting the separation effect of RAP, including the type of anionic surfactants, the surfactant concentration, the emulsion-to-RAP ratio, temperature, the rotation rate and time, and the RAP’s particle size, were investigated in depth, and the separation effect and its influence on the aggregate properties were evaluated. The experimental results indicate that when using the optimal process to mix and treat 13.2 mm and 9.5 mm RAP clusters, it is possible to achieve 100% separation of the coarse RAP above 4.75 mm, with a 64.58% reduction in the asphalt content. The angularity of the aggregate remained unchanged after separation. It was observed from scanning electron microscopy (SEM) images that the asphalt on the surface of the coarse aggregate had been eluted, and the morphology of the aggregate surface was completely exposed. This environmentally friendly separation method provides new possibilities for high-content RAP recycling in pavement engineering. Full article

Current biodiesel production is costly, in part due to the catalysts added during transesterification and later washed out. We have previously shown that intact rapeseed shells can be ball-milled with an alcohol to produce biodiesel without an added catalyst. Here, we report on the activation and identity of the complexing agent within the shells of rapeseeds and sunflower seeds. Lignin, present in the cell walls of plant matter, complexes with iron and manganese within metallic media, such as in a ball mill, and acts as a catalyst support in a transesterification reaction with oil and methanol. When ball-milled with methanol, rapeseed and sunflower seeds produce up to 90% biodiesel, similar to yields produced by industrial methods. However, this new method for producing biodiesel is a greener alternative, as it requires fewer organic solvents, may reduce the time and energy required for synthesis, and may reduce the effort required for product purification. Full article

Bis- and trisphosphines incorporating methylene and aryl spacers readily adsorb on the surface of porous activated carbon (AC). The adsorption can be performed in the absence of solvents, even when the phosphines have high melting points, or from solutions. The diverse phosphines Ph₂PCH₂PPh₂ (dppm), Ph₂P(CH₂)₂PPh₂ (dppe), Ph₂P(CH₂)₃PPh₂ (dppp), Ph₂P(p-C₆H₄)PPh₂ (dppbz), and (Ph₂PCH₂)₃CCH₃ (tdme) were adsorbed in submonolayers on AC. The adsorbed phosphines were studied by ³¹P MAS (magic angle spinning) NMR spectroscopy, and their mobilities on the surface were confirmed by determining the ³¹P T₁ relaxation times. All phosphine groups of each bis- and trisphosphine molecule are in contact with the surface, and the molecules exhibit translational mobility as one unit. All phosphines used here are air-stable. Once a submonolayer is created on the AC surface, oxygen from the air is co-adsorbed and transforms all phosphines quantitatively into phosphine oxides at room temperature. The oxidation proceeds in a consecutive manner with the oxidation of one phosphine group after another until the fully oxidized species are formed. Studies of the kinetics are based on integrating the signals in the solution ³¹P NMR spectra. High temperatures and low surface coverages increase the speed of the oxidation, while light and acid have no impact. The oxidation is fast and complete within one hour for 10% surface coverage at room temperature. In order to study the mechanism and slow down the oxidation, a higher surface coverage of 40% was applied. No unwanted P(V) side products or water adducts were observed. The clean phosphine oxides could be recovered in high yields by washing them off of the AC surface. The oxidation is based on radical activation of O₂ on the AC surface due to delocalized electrons on the AC surface. This is corroborated by the result that AIBN-derived radicals enable the air oxidation of PPh₃ in solution at 65 °C. When the air-stable complex (CO)₂Ni(PPh₃)₂ is applied to the AC surface and exposed to the air, OPPh₃ forms quantitatively. The new surface-assisted air oxidation of phosphines adsorbed on AC renders expensive and hazardous oxidizers obsolete and opens a synthetic pathway to the selective mono-oxidation of bis- and trisphosphines. Full article

Post-harvest processing (PHP) is a key determinant of coffee quality, flavor profile, and market classification, yet verifying PHP claims remains a significant challenge in the specialty coffee industry. This study introduces near-infrared spectroscopy (NIRS) coupled with chemometrics as a rapid, non-destructive approach to classify green coffee beans based on PHP. For the first time, seven distinct PHP categories—Alchemy, Anaerobic Processing (Deep Fermentation), Dry-Hulled, Honey, Natural, Washed, and Wet-Hulled—were discriminated using NIRS, encompassing 20 different processing protocols under varying environmental and fermentation conditions. The NIR spectra (350–2500 nm) of 524 green Arabica coffee samples were analyzed using PCA-LDA models (750–2450 nm), achieving classification accuracies up to 100% for underrepresented categories and strong performance (91–95%) for dominant PHP groups in an independent test set. These results demonstrate that NIRS can detect subtle chemical signatures associated with diverse PHP techniques, offering a scalable tool for quality assurance, fraud prevention, and traceability in global coffee supply chains. While limited sample sizes for some PHP categories may influence model generalization, this study lays the foundation for future work involving broader datasets and integration with digital traceability systems. The approach has direct implications for producers, traders, and certifying bodies seeking reliable, real-time PHP verification. Full article

This study aims to obtain findings on the internal water behavior, the presence of water channels, and the degree of washout due to rainfall infiltration in Japanese municipal solid waste (MSW) final disposal sites. Electrical resistivity tomography (ERT) monitoring and undistributed waste sampling for X-ray computed tomography (X-ray CT) analysis were conducted in the field. The study sites were targeted at Site A, which is mainly composed of non-combustible residues, and Site B, which is mainly composed of incineration ash. The time-dependent resistivity distributions obtained from real-time ERT monitoring were effective for us to understand the water content distribution after water infiltration during water injection tests. As a result, the global flow behavior and the local water channel flow were determined. In addition, X-ray CT analysis of the undisturbed waste samples obtained from the sites clarified the different pore structures, indicating the possibility of more advanced washing out at Site A than at Site B. Furthermore, the soil cover layer and gas extraction wells had a significant effect on the resistivity structure with respect to water flow behavior. Since soil cover layer and gas extraction wells are significant factors affecting waste stabilization by washout, it is suggested that these factors should be considered in the design and maintenance of landfills. Full article

The Quality by Design (QbD) concept has been widely applied to the optimization of traditional Chinese medicine production processes recently. This work focused on optimizing the critical purification process of Scutellaria baicalensis extract used in the preparation of Zhusheyong Shuanghuanglian. Considering the impact of noise parameters and changes in herbal properties, an experimental design method was employed for optimization. Multiple batches of Scutellaria baicalensis decoction were prepared in this research, and quantitative models of Scutellaria baicalensis herbal properties, critical process parameters (CPPs), and process evaluation indicators were established. The R² of the quantitative models were all higher than 0.80. According to the model, the yield of baicalin was identified as a critical material property (CMA). The pH of first acid precipitation (X₁), first temperature holding time (X₂), pH of alkalization (X₃), ethanol amount (X₄), and end pH of ethanol washing (X₅) were CPPs. Considering the difficulty in controlling the end pH of the ethanol washing, it was considered to be a noise parameter. The Monte Carlo probability-based method was used to calculate the design space, determining the range of controllable parameters, which was successfully validated through experiments. Normal operation ranges for controllable parameters are recommended as follows: X₁ of 0.8–2.2, X₂ of 25–35 min, X₃ of 6.5–7.5, and X₄ of 0.8–1.2 g/g. Full article

Gamma oryzanol (GO) is a natural anti-oxidant found in rice bran with potential health benefits. Conventional isolation of GO from rice bran requires the use of non-eco-friendly solvents such as acetone, ethyl acetate and hexane due to its low aqueous solubility. Further, nanoencapsulation of GO is required for the enhancement of stability and bioavailability. Plant-derived nanovesicles (PDNVs) are natural/intrinsic exosome-mimetic vesicles isolated from edible plants using green methods. Washed/soaked rice water (SRW) is often discarded as waste prior to cooking rice. However, traditional knowledge indicates its health-promoting anti-oxidant benefit, probably contributed by the presence of GO. Herein, for the first time, we isolated PDNVs from SRW by the cost-effective Polyethylene glycol 6000(PEG) precipitation method and demonstrated the presence of GO in PDNVs. In our initial screen, PDNVs were isolated from both rice grains (RGs) as well as the SRW of four different rice varieties, in which we identified the copious presence of GO in black RGs and brown SRW PDNVs. Both RG and SRW PDNVs were non-toxic to keratinocytes. SRW PDNVs displayed distinct cellular uptake mechanisms compared to RG PDNVs in human keratinocytes. Compared to native GO, brown SRW PDNVs containing GO displayed superior anti-oxidant activity in HaCaT keratinocytes, likely due to its enhanced cellular uptake. Overall, we describe here a waste-to-wealth green approach using an economical PEG method for the extraction of GO in bioavailable form. Given that oxidative stress is a driving factor for inflammation and related diseases, SRW PDNVs provide an affordable natural formulation for the treatment of diseases with underlying oxidative stress and inflammation. Full article