Search Results (321)

During the operation of structures, the components and materials from which they are made are exposed to various environmental, technological, and operational impacts. In this context, the use of a modified water-dispersion composition containing finely dispersed fillers with enhanced protective and performance characteristics proves to be effective. This article examines the development of a paint-and-coating composition using hollow glass microspheres and modified diatomite as finely dispersed fillers. The influence of technological factors on the properties of coating materials based on a synthesized acrylic dispersion and fillers—such as modified diatomite and hollow glass microspheres ranging from 20 to 100 μm in size with a bulk density of 0.107–0.252 g/cm³—is analyzed. The optimal formulation of the coating materials was determined to ensure the required coating quality. Experimental results demonstrate the improved strength and hardness of the coating due to the use of acrylic dispersion obtained through an emulsifier-free method and modifiers in the form of finely dispersed fillers. It has been established that the resulting samples also exhibit high adhesion to mineral and metallic substrates, along with excellent corrosion resistance. Moreover, the incorporation of acrylic dispersion contributes to increased elasticity of the coating, resulting in improved resistance to washing and abrasion. The developed protective material can be applied to a variety of surfaces, including walls, ceilings, and roofs of buildings and structures, pipelines, and many other applications. Thus, modified water-dispersion compositions based on synthesized acrylic dispersion showed the following results: resistance to sticking—5, which is the best; chemical resistance and gloss level with standard single-phase acrylic dispersion—no destruction or change in gloss. The adhesion of coatings cured under natural conditions and under the influence of UV radiation was 1 point. The developed formulations for obtaining water-dispersion paint and varnish compositions based on synthesized polymer dispersions, activated diatomite, and hollow glass microspheres, meet all the regulatory requirements for paint and varnish materials in terms of performance, and in terms of economic indicators, the cost of 1 kg of paint is 30% lower than the standard. Full article

Polymer membranes often face challenges of oil fouling and rapid water flux decline during the separation of oil-in-water emulsions, making them a focal point of ongoing research and development efforts. Coating PVDF membranes with a hydrogel layer equips the developed membranes with robust potential to mitigate oil fouling. However, developing a controllable thickness of a stable hydrogel layer to prevent the blocking of membrane pores remains a critical issue. In this work, atmospheric pressure low-temperature plasma was used to prepare the surface of a PVDF membrane to improve its wettability and adhesion properties for coating with a thin hydrophilic film of an AM-NaA copolymer hydrogel. The AM-NaA/PVDF membrane exhibited superhydrophilic and underwater superoleophobic properties, along with exceptional anti-crude oil-fouling characteristics and a self-cleaning function. The AM-NaA/PVDF membrane achieved high separation efficiency, exceeding 99% for various oil-in-water emulsions, with residual oil content in the permeate of less than 10 mg/L after a single-step separation. Additionally, it showed a high-water flux of 5874 L/m²·h for crude oil-in-water emulsions. The AM-NaA/PVDF membrane showed good stability and easy cleaning by water washing over multiple crude oil-in-water emulsion separation and regeneration cycles. Adding CaCl₂ destabilized emulsions by promoting oil droplet coalescence, further boosting flux. This strategy provides a practical pathway for the development of highly reusable and oil-fouling-resistant membranes for the efficient separation of emulsified oily water. Full article

Steel fibers are widely used in cementitious composite materials to enhance their mechanical properties, such as tensile strength and toughness. However, the effectiveness of these fibers largely depends on their surface characteristics and bonding with the cement matrix. This study investigated the effects of various treatment processes on the microhardness and mechanical strength of steel fibers in cementitious composite materials. These methods include acetone and acid washing, silane coupling agent treatment, and nanosilica coating. Fibers washed with acetone exhibited a cleaner surface, primarily due to the removal of impurities. Acid treatment resulted in a notably roughened surface, which significantly enhanced mechanical interlocking with the surrounding matrix. Silane treatment led to an uneven surface with distinct vertical textures, potentially improving adhesion properties. Meanwhile, fibers treated with nanosilica displayed a coating of nanoparticles adhering to the surface, which may further influence the fiber–matrix interaction. The results of the mechanical properties tests indicated that nanosilica coating was the most effective in improving both the flexural and compressive strengths, especially in the early strengths in the cement matrix. Full article

The widespread phase-out of long-chain per- and poly-fluoroalkyl substances (PFASs) has created an urgent need for durable, fluorine-free water-repellent finishes that match the performance of legacy chemistries while minimising environmental impact. Here, the performance of an eco-friendly hybrid organic–inorganic treatment obtained by the in situ hydrolysis–condensation of triethoxy(octyl)silane (OS) in an amino-terminated polydimethylsiloxane (APT-PDMS) aqueous dispersion was investigated. The sol was applied to plain-weave cotton and polyester by a pad-dry-cure process and benchmarked against a commercial fluorinated finish. Morphology and chemistry were characterised by SEM–EDS, ATR-FTIR, and Raman spectroscopy; wettability was assessed by static contact angle, ISO 4920 spray ratings, and AATCC 193 water/alcohol repellence; and durability, handle, and breathability were evaluated through repeated laundering, bending stiffness, and water-vapour transmission rate measurements. The silica/PDMS coating formed a uniform, strongly adherent nanostructured layer conferring static contact angles of 130° on cotton and 145° on polyester. After five ISO 105-C10 wash cycles, the treated fabrics still displayed a spray rating of 5/5 and AATCC 193 grade 7, outperforming or equalling the fluorinated control, while causing ≤5% loss of water-vapour permeability and only a marginal increase in bending stiffness. These results demonstrate that the proposed one-step, water-borne sol–gel process affords a sustainable, industrially scalable route to high-performance, durable, water-repellent finishes for both natural and synthetic textiles, offering a viable alternative to PFAS-based chemistry for outdoor apparel and technical applications. Full article

Blood samples and testing are routine in healthcare. Presently, there is a growing interest in using tear samples in place of blood. Tear samples can be obtained non-invasively and collection does not require the skills of a trained phlebotomist. Red blood cells and other cells are not present in tears, which avoids centrifugation. Importantly, basal tear samples contain most of the biomarkers present in blood. The difficulty is the small volume of basal tears, which is about 7 μL in each eye. Any contact with the eye results in additional reflex tears with a different chemical composition. The small tear samples are collected with capillary tubes and then sent out for amplified assays, such as enzyme-linked immunosorbent assay (ELISA) or polymerase chain reaction (PCR). The results are not available for several days or a week and, therefore, are less useful in an ophthalmology office. We propose the use of a contact lens that contains bound antibodies for fluorescence immunoassays. The lenses could be removed from the patient for point-of-care measurements at the bedside. To prove that this concept is possible, we performed a three-layer protein capture assay that mimics an immunoassay. For convenience, we used lysozyme (Lys), which spontaneously coats silicon hydrogel (SiHG) contact lenses (CL). Anti-lysozyme IgG was the second layer captured, with anti-lysozyme considered to be the target biomarker. The third layer was rhodamine or Alexa Fluor-labeled Ab against the IgG Fc region, considered to be the detection antibody. The multiple protein layers were stable and did not wash off the SiHG lenses. These results strongly suggest the contact lens can be used for capture immunoassays for a wide variety of biomarkers. Full article

Textile structures with ohmic (Joule) heating capability are frequently used for personal thermal management by tuning fluctuations in human body temperature that arise due to climatic changes or for medical applications as electrotherapy. They are constructed from electrically conductive textile structures prepared in different ways, e.g., from metallic yarns, conductive polymers, conductive coatings, etc. In comparison with other types of flexible ohmic heaters, these structures should be corrosion resistant, air permeable, and comfortable. They should not loose ohmic heating efficiency due to frequent intensive washing and maintenance. In this study, the basic electrical properties of a conductive fabric composed of a polyester/cotton fiber mixture and a small amount of fine stainless-steel staple fibers (SS) were evaluated and predicted. Even though the basic conductive component of SS fibers is iron and its electrical characteristics obey Ohm’s law, the electrical behavior of the prepared fabric was highly nonlinear, resembling a more complex response than that of a classical conductor. The non-linear behavior was probably due to non-ideal, poorly defined random interfaces between individual short SS fibers. A significant time–dynamics relationship was also shown. Using the Stefan–Boltzmann law describing radiation power, we demonstrated that it is possible to predict surface temperature due to the ohmic heating of a fabric related to the input electrical power. Significant local temperature variations in the heated hybrid fabric in both main directions (warp and weft) were identified. Full article

This study explores the development and optimization of quartz-based filtration media for industrial oil–water separation, focusing on enhancing surface wettability, minimizing fouling, and improving oil rejection efficiency. High-purity quartz particles (SiO₂: 98%, Fe₂O₃: 0.18%, particle size: 0.8–1.8 mm) were evaluated in three configurations: raw, acid-washed, and surface-coated with hydrophilic nanoparticles (Al₂O₃ and P₂O₅). The filtration medium was constructed as a packed-bed of quartz particles rather than a continuous sintered membrane, providing a cost-effective and modular structure for separation processes. Comprehensive material characterization was performed using X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), and Energy Dispersive Spectroscopy (EDS). XRD confirmed the crystalline stability of quartz across all treatments, while SEM and EDS revealed enhanced surface morphology and elemental distribution—especially phosphorus and aluminum—in coated samples. Performance testing with synthetic oily wastewater (initial oil concentration: 183,754.8 mg/L) demonstrated that the coated quartz medium achieved superior separation, reducing residual oil concentration to 29.3 mg/L, compared to 1583.7 mg/L and 1859.8 mg/L for washed and raw quartz, respectively. Contact angle analysis confirmed improved hydrophilicity in coated media, which also exhibited lower fouling propensity. Taguchi optimization (conducted via Minitab 21.3) and regression modeling identified surface coating and operational pressure (optimal at 2.5 bar) as the most significant parameters influencing oil rejection. Post-filtration SEM and XRD confirmed structural integrity and coating durability. Additionally, flux recovery above 90% after backwashing indicated strong regeneration capability. These findings validate surface-modified quartz packed beds as robust, scalable, and economically viable alternatives to conventional membranes in oily wastewater treatment. Future research will explore multilayer coatings, long term performance under aggressive conditions, and AI-based prediction models. Full article

Fiber-shaped electrical heaters with high flexibility and excellent adaptability make an ideal candidate for the application of wearable electronics but still suffer from low strength and poor durability. Herein, an all-in-one Joule-heating fiber capable of outstanding mechanical properties, good heating efficiency, and long-term stability is reported by using polymer-assisted metal deposition to firmly coat Cu nanoparticles on high-performance liquid crystal polymer (LCP) fibers. Taking advantage of LCP, the resultant fibers exhibit a satisfying temperature threshold (up to 200 °C) and immense strength (2.94 GPa). By virtue of dense and continuous Cu film, these fibers show low electrical resistance (5.51 Ω/cm) and an ultrafast response rate (12.6 °C·s⁻¹) at low supplied voltages (0.5–3.5 V). Benefiting from the levodopa/polyethyleneimine interface design, such fibers maintain nearly constant resistance after repeatable bending, folding, and even washing (50 cycles). Based on the above-mentioned merits, a wearable patch with a Joule-heating function is knitted by using as-made fibers to offer therapeutic benefits for human body joints. This work demonstrates prospective potential for enriching the challenging applications of fiber-shaped electrical heating systems. Full article

Smart textiles are an evolving field, but challenges in durability, washing, interfacing, and sustainability persist. Widespread adoption requires robust, lightweight, fully integrated fiber-based conductors. This paper proposes using ultralong carbon nanotube (UCNT) yarns with a width-to-length ratio of several orders of magnitude larger than typical carbon nanotube fibers. These yarns enable the manufacturing of stable, workable structures, composed of a network of twisted fibers (tows), which are suitable for fabric integration. Our research includes the creation of textile prototype demonstrators integrated with coated and non-coated UCNT yarns, tested under military-grade standards for both mechanical durability and electric functionality. The demonstrators were evaluated for their electrical and mechanical properties under washability, abrasion, and weathering. Notably, polymer-coated UCNT yarns demonstrated improved mechanical durability and electrical performance, showing promising results. However, washing tests revealed the presence of UCNT nanofibers in the residue, raising concerns due to their classification as hazards by the World Health Organization. This paper examines the sources of fiber release and discusses necessary improvements to coating formulations and testing protocols to mitigate fiber loss and enhance their practical viability. These findings underscore both the potential and limitations of UCNT yarns in military textile applications. Full article

3D-printing enables the fabrication of membranes with desired shapes and geometrical parameters. In this study, a membrane for pressure-driven processes was manufactured in a single step using the fused deposition modeling (FDM) technique. The membrane was produced from a mixture of polylactic acid (PLA) with sucrose as a pore-forming agent. Sucrose was removed from the final membrane by washing it with water. The membrane consists of three layers, and this sandwich-like structure ensures its mechanical stability. The material obtained was characterized using SEM and AFM imaging, as well as nitrogen adsorption-desorption and contact angle measurements. The porosity of each layer of the membrane is due to a loose region, which is coated on both sides with a dense film formed during printing. The pores responsible for rejection capability can be found in grooves between the polymer stripes in the dense layer. The membrane exhibits a water permeability of 64 L m⁻²h⁻¹bar⁻¹, with a molecular weight cut-off of 69 kDa. The PLA membrane can be used for polyphenol concentration, demonstrating a permeability of 2–3.4 L m⁻²h⁻¹bar⁻¹ and a selectivity towards these compounds of 78–98% at 0.5 bar, with a flux decline ratio of up to 50%. Full article

This research explores the development of highly durable flexible electronic textiles (e-textiles) for wearable electronics, focusing on improving their washability and performance. A conductive graphene-based ink was screen-printed onto a polyester textile. Water-based polyurethane (PU) coatings with variable crosslinker ratios and thickener were applied to solve washability issues. The results show that the PU coatings significantly enhanced the electrical stability and durability of the printed pathways after multiple washing cycles. The conductivity remained intact after 120 washing cycles, indicating that the final properties of the e-textile, which contained 6 wt% thickener and 3 wt% crosslinker, provided effective water protection. The results highlight the promise of these coated e-textiles for wearable electronics applications, especially in the occupational and healthcare sectors, where long-term flexibility and washability are critical. Full article

Drug-coated balloons (DCBs) are designed to deliver an anti-proliferative drug to the stenotic vessel to combat restenosis after an angioplasty treatment. However, significant drug loss can occur during device navigation toward the lesion site, thus reducing the delivery efficiency and increasing the off-target drug loss. In this framework, this study aimed to design a novel in vitro setup to estimate the drug loss due to blood flow–coating interaction during tracking. The system consists of a millifluidic chamber, able to host small drug-coated flat patches representative of DCBs, connected at the inlet to a syringe pump able to provide an ad hoc flow and, at the outlet, to a vial collecting the testing fluid with possible drug removed from the specimen. Unlike other studies, the device presented here uniquely evaluates flow-related drug loss from smaller-scale DCB samples, making it a precise, easy-to-use, and efficient assessment tool. In order to define proper boundary conditions for these washing off tests, computational fluid dynamics (CFD) models of a DCB in an idealized vessel were developed to estimate the wall shear stresses (WSSs) experienced in vivo by the device when inserted into leg arteries. From these simulations, different target WSSs were identified as of interest to be replicated in the in vitro setup. A combined analytical–CFD approach was followed to design the testing system and set the flow rates to be imposed to generate the desired WSSs. Finally, a proof-of-concept study was performed by testing eight coated flat specimens and analyzing drug content via high-performance liquid chromatography (HPLC). Results indicated different amounts of drug loss according to the different imposed WSSs and confirmed the suitability of the designed system to assess the washing off resistance of different drug coatings for angioplasty balloons. Full article

Recent advancements in smart textiles have facilitated their extensive application in wearable health monitoring, particularly in brain activity measurement. This study introduces a flexible and washable fabric dry electroencephalography (EEG) electrode designed for brain activity measurement. The fabric dry electrode is constructed from electrically conductive polyester fabric with a resistivity of 0.09 Ω·cm, achieved by applying a PEDOT: PSS/PVA conductive paste coating on the textile substrate. A comparative analysis of the tensile properties between the conductive and untreated polyester fabric was conducted. The SEM images demonstrated that the PEDOT: PSS/PVA conductive polymer composite resulted in a uniform coating on the fabric surface. When enveloped in elastic foam, the fabric dry electrode maintained a low and stable electrode–skin contact impedance during prolonged EEG monitoring. Additionally, the short circuit noise level of the fabric dry electrode exhibited superior performance compared to both Ag/AgCl wet and finger dry electrode. The EEG signals acquired from the fabric dry electrode were comparable to those recorded by the Ag/AgCl wet electrode. Moreover, the fabric electrode effectively captured clear and reliable EEG signals, even after undergoing 10 washing cycles. The fabric dry electrode indicates good sweat resistance and biocompatibility during prolonged monitoring. Full article

A critical challenge in wearable electrothermal textiles is achieving effective insulation while maintaining sheath flexibility, which is essential for enhancing the mechanical properties and durability of conductive materials under everyday conditions, such as washing, stretching, and twisting. In this work, we employ a coaxial tubular braiding technique to coat a high-conductivity carbon nanotube (CNT) yarn with a high-strength insulation layer made of ultra-high-molecular-weight polyethylene (UHMWPE) multifilaments, resulting in a core–sheath-structure CNT yarn with excellent electrothermal performance. By adjusting the number of UHMWPE multifilaments and the sheath braiding angle, we achieve high flexibility, high tensile strength, and abrasion and wash resistance, as well as improved electrical stability for the CNT yarns. Additionally, the CNT yarns with an insulation layer effectively prevent short-circuiting during use and achieve superior thermal management, with a significant increase in steady-state temperature under operational conditions, exhibiting significant potential for applications in wearable electronic devices. Full article

The shift toward sustainable energy sources is essential to curb greenhouse gas emissions and satisfy energy demands. Among renewable options, carbon-based materials—such as agricultural residues and municipal solid waste—provide a dual advantage by generating energy and fuels while also reducing landfill waste. A notable innovation is transforming plastic waste into methane-rich streams via catalytic hydrogasification, a process in which carbon-based feedstocks interact with hydrogen using a selective catalyst. In this study, a structured catalyst was developed, characterized, and tested for converting plastic waste samples. The thermal degradation properties of plastic waste were first studied using thermogravimetric analysis. The catalyst was prepared using an Oxygen Bonded Silicon Carbide (OBSiC) open-cell foam as the carrier, coated with γ-Al₂O₃-based washcoat, CeO₂, and Ni layers. It was characterized in terms of specific surface area, coating adhesion, pore distribution, acidity, and the strength of its active sites. Experimental tests revealed that a hydrogen-enriched atmosphere significantly enhances CH₄ formation. Specifically, during catalytic hydrogasification, methane selectivity reached approximately 59%, compared to 6.7%, 13.7%, and 7.8% observed during pyrolysis, catalyzed pyrolysis, and non-catalyzed hydrogasification tests, respectively. This study presents a novel and effective approach for converting plastic waste using a structured catalyst, a method rarely explored in literature. Full article