Search Results (101)

Deep drilling and horizontal wells, as important means of unconventional oil and gas development, face problems with the high energy consumption but low removal efficiency of traditional well washing equipment, the uneven cleaning of horizontal well intervals, and an insufficient degree of automation. This paper proposes a novel hydraulic drive well washing device which consists of two main units. The wellbore cleaning unit comprises a hydraulic drive cutting–flushing module, a well cleaning mode-switching module, and a filter storage module. The unit uses hydraulic and mechanical forces to perform combined cleaning to prevent mud and sand from settling. By controlling the flow direction of the well washing fluid, it can directly switch between normal and reverse washing modes in the downhole area, and at the same time, it can control the working state of corresponding modules. The assembly control unit includes the chain lifting module and the arm assembly module, which can lift and move the device through the chain structure, allow for the rapid assembly of equipment through the use of a mechanical arm, and protect the reliability of equipment through the use of a centering structure. The device converts some of the hydraulic power into mechanical force, effectively improving cleaning and plugging removal efficiency, prolonging the downhole continuous working time of equipment, reducing manual operation requirements, and comprehensively improving cleaning efficiency and energy utilization efficiency. Full article

The application of an ultrafiltration (UF) process with periodic membrane cleaning with the use of alkaline detergent solutions was proposed for the recovery of wash water from car wash effluent. In order to test the resistance of the membranes to the degradation caused by the cleaning solutions, a pilot plant study was carried out for almost two years. The installation included an industrial module with FP100 tubular membranes made of polyvinylidene fluoride (PVDF). The module was fed with synthetic effluent obtained by mixing foaming agents and hydrowax. To limit the fouling phenomenon, the membranes were cleaned cyclically with P3 Ultrasil 11 solution (pH = 11.7) or Insect solution (pH = 11.5). During plant shutdowns, the membrane module was maintained with a sodium metabisulphite solution. Changes in the permeate flux, turbidity, COD, and surfactant rejection were analysed during the study. Scanning electron microscopy (SEM), atomic force microscopy (AFM), differential scanning calorimetry (DSC), and Fourier-transform infrared spectroscopy (FTIR) analysis were used to determine the changes in the membrane structure. As a result of the repeated chemical cleaning, the pore size increased, resulting in a more than 50% increase in permeate flux. However, the quality of the recovered wash water did not deteriorate, as an additional separation layer was formed on the membrane surface due to the fouling phenomenon. Full article

Lepidolite is one of a small number of minerals that contains a significant amount of lithium. Some areas, like the Apuseni and Metalifer Mountains in Romania, present dark red layers intercalated with reddish-yellow clay soils with interesting aspects. X-ray diffraction (XRD) analysis coupled with polarized light optical microscopy (POM) revealed that this dark red soil contains a large amount of fine microstructured lepidolite (24–35%) mixed with quartz sand and fine traces of kaolinite and muscovite. Scanning electron microscopy (SEM) elemental analysis revealed a typical clay composition with Mn traces (specific to red lepidolite), confirming POM observation. SEM also revealed fine tabular platelets of lepidolite with a maximum size of 1.5 µm surrounding quartz particles (5–50 µm), indicating the presence of numerous nano fractions. Their presence was confirmed by atomic force microscopy (AFM), which showed particle sizes ranging from 40 to 60 nm, closely matching the crystallite size estimated using the Scherrer formula. The finest fraction allows easy separation from the quartz sand through bi-distilled water washing. Quartz particles settle at the bottom of the container, while the finest lepidolite particles are easily separated. Water evaporation ensures their recovery. Thus, the enriched lepidolite powder could be utilized for specific applications in the lithium industry. On the other hand, the large number of the finest particles found in the samples investigated presents the risk of PM1, PM2.5m, and PM10 emission, with impacts on atmospheric environmental safety. Full article

The dynamic relationship between microplastics (MPs) in the air and on the Earth’s surface involves both natural and anthropogenic forces. MPs are transported from the ocean to the air by bubble scavenging and sea spray formation and are released from land sources by air movements and human activities. Up to 8.6 megatons of MPs per year have been estimated to be in air above the oceans. They are distributed by wind, water and fomites and returned to the Earth’s surface via rainfall and passive deposition, but can escape to the stratosphere, where they may exist for months. Anthropogenic sprays, such as paints, agrochemicals, personal care and cosmetic products, and domestic and industrial procedures (e.g., air conditioning, vacuuming and washing, waste disposal, manufacture of plastic-containing objects) add directly to the airborne MP load, which is higher in internal than external air. Atmospheric MPs are less researched than those on land and in water, but, in spite of the major problem of a lack of standard methods for determining MP levels, the clothing industry is commonly considered the main contributor to the external air pool, while furnishing fabrics, artificial ventilation devices and the presence and movement of human beings are the main source of indoor MPs. The majority of airborne plastic particles are fibers and fragments; air currents enable them to reach remote environments, potentially traveling thousands of kilometers through the air, before being deposited in various forms of precipitation (rain, snow or “dust”). The increasing preoccupation of the populace and greater attention being paid to industrial ecology may help to reduce the concentration and spread of MPs and nanoparticles (plastic particles of less than 100 nm) from domestic and industrial activities in the future. Full article

The porosity of hair fibers can be modified by chemical and physical damage, influencing their response to cosmetic treatments. To investigate the effect of commonly applied hair care protocols on textured hair, virgin and once-bleached tresses were subjected to multiple cycles of washing, blow-drying while combing, and styling with a hot flat iron, simulating a consumer routine spanning one to six months. Porosity-related properties were evaluated using swelling test, fluorescence, atomic force, and scanning electron microscopies, high-pressure differential scanning calorimetry, and tensile testing. Both chemical and physical processes induced significant changes in the hair’s water permeability, surface topography, and appearance, alongside a reduction in mechanical and thermal properties, indicating substantial structural alterations compared to virgin hair. Increased porosity compared to virgin hair possibly reduced the heat conductivity of bleached hair, leading to less pronounced effects of heat exposure. These findings underscore the damaging potential of routine practices for textured hair and emphasize the need for targeted cosmetic solutions to protect and repair these fibers as part of consumers’ hair care regimens. Full article

Transport and vehicle traffic are closely connected with particulate matter (PM) pollution, inducing various fractions into the atmosphere, some of them forming significant deposits on the surface of the car. They are washed away during carwash-inducing slurries collecting the PM deposits, which are characteristic of a large area. Crystalline PM matter was investigated by XRD coupled with polarized optical microscopy (POM). Organic matters were investigated by Fourier-Transform Infrared spectrometry (FTIR) and gas chromatography, GC-MS. Their microstructure and elemental composition were investigated by SEM-EDX. The crystalline features contain mainly quartz, calcite, and clay (muscovite and kaolinite) particles having traces of goethite and lepidocrocite. Slurry particle size distribution was established by sieving on the following meshes: 63 µm, 125 µm, 250 µm, 500 µm, 1000 µm, 2000 µm, and 4000 µm. Coarse fractions of 250–4000 μm are dominated by quartz and calcite particles. The quartz and calcite amount decreases with particle size, while the muscovite and kaolinite amount increases in the finest fractions of 0–125 μm. Organic matter was evidenced, firstly, by FTIR spectroscopy, revealing mostly CH₂; C=O, and NH₄ bonds that are more intense for the fine particulate fractions. The organic deposits form mainly amorphous crusts associated with micro- and nano-plastic particles related to the phthalates and traces of the washing detergents. Atomic Force Microscopy revealed their size range between 60 and 90 nm and evidenced nanoparticles within samples. The nanofractions adhere to the bigger particles in humid environments, assuring their immobilization to reduce their hazardous potential. Carwash slurry blending with fertile soil ensures proper grass seed germination and growth at mixtures of up to 60% slurry, allowing its sustainable reconversion as soil for landfill and dump rehabilitation, preventing the PM emission hazard. Blended compositions containing more than 60% slurry have noxious effects on the grass seeds, inhibiting their germination. Full article

In order to reduce chronic hair flyaways/frizz, both reducing and oxidizing agents have to be used, leaving aside the hair damage issues. This study presents changes in hair morphology caused by treatment with a shampoo containing only reducing agents, excluding oxidizing agents that affect critical hair damages. As a result of flyaway/frizz improvement rates calculated through monitoring of the area of light transmittance in the hair tresses, reducing agents, such as ammonium thioglycolate (ATG), L-cysteine, and sodium sulfite were found to be effective in decreasing hair flyaway/frizz. Additionally, the methods to maintain homeostasis and control damage caused by oxidation during washing were also used to see flyaway/frizz improvement rates. Measurements using electrostatic force microscopy (EFM) showed that the surface charge of hair tresses treated with shampoo containing reducing agents was lowered. Using Raman spectroscopic analysis, it has been suggested that these treatments with reducing agents induced a 3D structural transition of the hair from an α-helix to a random coil. In addition, this structural release was confirmed, identifying the reduction in the enthalpy of the α-helix using differential scanning calorimetry (DSC). Furthermore, we verified that this change causes no hair damage through a tensile strength test. Therefore, the formulation of shampoo with reducing agents can be used as an effective strategy to care for hair flyaway/frizz without hair damage issues. Full article

In recent years, additive manufacturing (AM) has been recognized as a transformative force in the dental industry, with the ability to address escalating demand, expedite production timelines, and reduce labor-intensive processes. Despite the proliferation of three-dimensional printing technologies in dentistry, the absence of well-established post-processing protocols has posed formidable challenges. This comprehensive review paper underscores the critical importance of precision in post-processing techniques for ensuring the acquisition of vital properties, encompassing mechanical strength, biocompatibility, dimensional accuracy, durability, stability, and aesthetic refinement in 3D-printed dental devices. Given that digital light processing (DLP) is the predominant 3D printing technology in dentistry, the main post-processing techniques and effects discussed in this review primarily apply to DLP printing. The four sequential stages of post-processing support removal, washing, secondary polymerization, and surface treatments are systematically navigated, with each phase requiring meticulous evaluation and parameter determination to attain optimal outcomes. From the careful selection of support removal tools to the consideration of solvent choice, washing methodology, and post-curing parameters, this review provides a comprehensive guide for practitioners and researchers. Additionally, the customization of post-processing approaches to suit the distinct characteristics of different resin materials is highlighted. A comprehensive understanding of post-processing techniques is offered, setting the stage for informed decision-making and guiding future research endeavors in the realm of dental additive manufacturing. Full article

The rising global need for clean water highlights the importance of efficient sample preparation methods to separate and wash various contaminants such as microparticles. Microfluidic methods for these purposes have emerged but they mostly deliver either separation or washing, with very low throughputs. Here, we investigate parallelization of a curved-channel particle separation and washing device in order to increase its throughput for sample preparation. A curved microchannel applies inertial forces to focus larger 10 µm microparticles at the inner wall of the channel and separate them from smaller 5 µm microparticles at the outer wall. At the same time, Dean flow recirculation is used to exchange the carrier solution of the large microparticles to a clean buffer (washing). We increased the number of curved channels in a stepwise manner from two to four to eight channels in two different arraying designs, i.e., rectangular and polar arrays. We examined efficient separation of target 10 µm particles from 5 µm particles, while transferring the larger microparticles into a clean buffer. Dean flow recirculation studies demonstrated that the rectangular arrayed device performs better, providing solution exchange efficiencies of more than 96% on average as compared to 89% for the polar array device. Our 8-curve rectangular array device provided a particle separation efficiency of 98.93 ± 0.91%, while maintaining a sample purity of 92.83 ± 1.47% at a high working flow rate of 12.8 mL/min. Moreover, the target particles were transferred into a clean buffer with a solution exchange efficiency of 96.81 ± 0.54% in our 8-curve device. Compared to the literature, our in-plane parallelization design of curved microchannels resulted in a 13-fold increase in the working flow rate of the setup while maintaining a very high performance in particle separation and washing. Our microfluidic device offers the potential to enhance the throughput and the separation and washing efficiencies in applications for biological and environmental samples. Full article

Cotton fiber consumption is higher than any other natural fiber due to its superior mechanical and physical properties. In the conventional reactive dyeing process, the dye undergoes hydrolysis due to hydrogen bonding and weak Van der Waals forces, yielding poor washing color fastness. Additionally, the post-dyeing wash-off process consumes significant amounts of water, energy, and time in order to remove the unreacted and hydrolyzed dye. Therefore, reactive dyes are predominantly utilized to color cotton fabrics as the covalent bond formed between dye and fiber results in excellent washing fastness for a wide range of colors, and improved ease of use. To support more efficient, economical, and sustainable reactive dyeing, polymers can be used as effective dye transfer inhibitors (DTIs) in the reactive wash-off process. In this study, poly(vinylpyrrolidone) (PVP) homopolymer and poly(vinylpyrrolidone)-co-poly(vinylimidazole) (PVP-co-PVI) were synthesized at different molecular weights. These polymers were then employed as DTIs to evaluate their performance during the wash-off process for dyed cotton fabrics treated with three reactive dyes (Reactive Red 195, Reactive Blue 221, and Reactive Yellow 145). It is noteworthy to mention that the alternative wash-off procedure involved only three stages, in contrast to the series of washing steps necessary in the conventional method. Evaluation of the DTIs was focused on parameters such as color strength, washing fastness, chemical oxygen demand (COD), as well as energy, water, and time consumption. The findings revealed that while the polymer DTIs generated minor differences in dyed fabric colors in comparison to conventional dyeing, they significantly improved washing fastness. The polymer DTIs studied display excellent potential to provide a much more sustainable dyeing process by saving 90% energy, 40% water, and 50% time versus conventional wash-off processing. The wastewater COD values from the polymer-assisted reactive dye wash-off process were higher for all reactive dyes tested than those from conventional processing. While the higher COD values are attributed to the lower water volumes, this finding highlights the need for further studies. In summary, PVP polymers successfully served as DTIs in the reactive dyeing washing-off process, providing massive water-energy-time efficiency improvements and, subsequently, a more sustainable process for cotton fabric dyeing. Full article

The destructive forces of tropical cyclones can have significant impacts on the land, contributing to degradation through various mechanisms such as erosion, debris, loss of vegetation, and widespread damage to infrastructure. Storm surge and flooding can wash away buildings and other structures, deposit debris and sediments, and contaminate freshwater resources, making them unsuitable for both human use and agriculture. High winds and flooding often damage electrical disubstations and transformers, leading to disruptions in electricity supply. Restoration can take days or even weeks, depending on the extent of the damage and the resources available. In the meantime, communities affected by power outages may experience difficulties accessing essential services and maintaining communication. In this study, we used a weighted maximum likelihood classification algorithm to reclassify NOAA’s National Geodetic Survey Emergency Response Imagery scenes into debris, sand, water, trees, and roofs to assess the extent of the damage around Mexico Beach, Florida, following the 2018 Hurricane Michael. NASA’s Visible Infrared Imaging Radiometer Suite (VIIRS) Day/Night Band (DNB) was processed to estimate power outage duration and rate of restoration in the Florida Panhandle based on the 7-day moving averages. Percent loss of electrical service at a neighborhood level was estimated using the 2013–2017 American Community Survey block group data. Spatial lag models were employed to examine the association between restoration rates and socioeconomic factors. The analysis revealed notable differences in power-restoration rates between urbanized and rural areas and between disadvantaged and more affluent communities. The findings indicated that block groups with higher proportions of minorities, multi-family housing units, rural locations, and households receiving public assistance experienced slower restoration of power compared to urban and more affluent neighborhoods. These results underscore the importance of integrating socioeconomic factors into disaster preparedness and recovery-planning efforts, emphasizing the need for targeted interventions to mitigate disparities in recovery times following natural disasters. Full article

There has been a recent uptake in the use of polyether-ether-ketone (PEEK), which is an organic thermoplastic polymer, in the manufacturing of various medical devices, implants, and equipment. Finding the best time and procedure for PEEK after sulfonation is the goal of this research. A total of 30 PEEK discs were sulfonated in this study by immersing them in concentrated (H₂SO₄) sulfuric acid for various durations and subsequently treated using various post-treatment techniques. Five experiments were carried out, aimed studying the effect of immersion time (5 s–2 min). The methods used as post-treatment were hydrothermal treatment, immersion in NaOH, and washing with acetone. The sulfonation time was measured, and the post-treatment techniques, surface characterizations, were conducted using scanning electron microscopy (SEM) (Electron Optics Instruments, LLC., West Orange, NJ, USA), atomic force microscopy (AFM) (AFM, Vía Burton, CA, USA), and hydrophilic properties. The results were confirmed by attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR). The findings of this study demonstrate that sulfonating PEEK caused a structure with a porous network to form in every sample. As the sulfonation time increased, the porous structure became more noticeable and the concentration increased. As a consequence, the roughness of the surface increased notably, and the modified PEEK surface’s wettability improved noticeably. Hydrothermal treatment was determined to be the most successful way for eliminating the leftover sulfuric acid, and sulfonation for 2 min was determined to be ideal. By understanding the best post-treatment procedures and ideal sulfonation duration, a theoretical foundation for the production of sulfonated PEEK for orthopedic uses may be laid. Full article

A novel micro-dispersed-gel (MDG)-strengthened-alkali-compound flooding system was proposed for enhanced oil recovery in high-water-cut mature oilfields. Micro-dispersed gel has different adaptability and application schemes with sodium carbonate and sodium hydroxide. The MDG-strengthened-alkali flooding system can reduce the interfacial tension to an ultra-low interfacial-tension level of 10⁻² mN/m, which can reverse the wettability of rock surface. After 30 days aging, the MDG-strengthened-Na₂CO₃ flooding system has good viscosity retention of 74.5%, with an emulsion stability of 79.13%. The enhanced-oil-recovery ability of the MDG-strengthened-Na₂CO₃ (MDGSC) flooding system is 43.91%, which is slightly weaker than the 47.78% of the MDG-strengthened-NaOH (MDGSH) flooding system. The crude-oil-production mechanism of the two systems is different, but they all show excellent performance in enhanced oil recovery. The MDGSC flooding system mainly regulates and seals micro-fractures, forcing subsequent injected water to enter the low-permeability area, and it has the ability to wash the remaining oil in micro-fractures. The MDGSH flooding system mainly removes the remaining oil on the rock wall surface in the micro-fractures by efficient washing, and the MDG particles can also form weak plugging of the micro-fractures. The MDG-strengthened-alkali flooding system can be used as an alternative to enhance oil recovery in high-water-cut and highly heterogeneous mature oilfields. Full article

Sensors based on triboelectric nanogenerators (TENGs) are increasingly gaining attention because of their self-powered capabilities and excellent sensing performance. In this work, we report a Mo₂CT_x-based triboelectric sensor (Mo-TES) consisting of a Mo₂CT_x/polydimethylsiloxane (PDMS) composite film. The impact of the mass fraction (wt%) and force of Mo₂CT_x particles on the output performance of Mo-TES was systematically explored. When Mo₂CT_x particles is 3 wt%, Mo-TES3 achieves an open-circuit voltage of 86.89 V, a short-circuit current of 578.12 nA, and a power density of 12.45 μW/cm². It also demonstrates the ability to charge capacitors with varying capacitance values. Additionally, the Mo-TES3 demonstrates greater sensitivity than the Mo-TES0 and a faster recovery time of 78 ms. Meanwhile, the Mo-TES3 also demonstrates excellent stability in water washing and antifatigue testing. This demonstrates the effectiveness of Mo-TES as a pressure sensor. Furthermore, leveraging the principle of electrostatic induction, the triboelectric sensor has the potential to achieve non-contact sensing, making it a promising candidate for disease prevention and safety protection. Full article

The effect of lecithin addition on the gelling characteristics and oxidative stability of single-washed mackerel (Auxis thazard) surimi was investigated in this study. Surimi was chopped in the presence of 2.5% (w/w) NaCl with different concentrations of lecithin (0, 0.1, 0.5, 1, and 1.5 g/100 g surimi). The rheological behavior, gel-forming ability, microstructure, and lipid oxidation of lecithin-added surimi varied significantly depending on lecithin content. When compared to the control, lecithin at 0.1, 0.5, and 1 g/100 g improved the breaking force of the gel (p < 0.05). The breaking force of the gel decreased significantly as lecithin concentration increased (up to 1.5 g/100 g) (p < 0.05). Deformation, on the other hand, reacted differently to the lecithin than it did to the breaking force. At a lecithin level of 0.1 g/100 g, the surimi gel displayed improved deformation (p < 0.05). Nonetheless, at higher doses (0.5–1.5 g/100 g), lecithin considerably reduced surimi gel deformation (p < 0.05), and the gel containing lecithin at 1.5 g/100 g showed significantly decreased deformation. Surimi with 0.1 g/100 g lecithin had the lowest expressible drip (p < 0.05). In general, lecithin at concentrations ranging from 0.1 to 1 g/100 g reduced expressible drip (p < 0.05), but not at 1.5 g/100 g, which was equivalent to the control (p > 0.05). Adding lecithin to mackerel surimi improved its whiteness slightly, regardless of concentration. Lecithin impacted the microstructures of surimi gel in a concentration-dependent manner. Lecithin at a concentration of 0.1 g/100 g produced a densely packed network with small, jointed clusters and minimal holes within the gel. Joined clusters in the gel were reduced by 0.5–1.5 g/100 g lecithin, and continuous aggregates predominated. Surprisingly, at higher doses of lecithin, notably 1.5 g/100 g, porous structures with continuous voids were perceived. Surimi gels treated with various lecithin doses had lower thiobarbituric acid reactive substances (TBARS) levels than the control (p < 0.05). Overall, lecithin at a low concentration of 0.1 g/100 g was most effective at improving the texture, increasing water-holding capacity, lightening the color, and delaying lipid oxidation of single-washed mackerel surimi. Full article