Search Results (80)

An IN738 alloy with a high Al and Ti contents induces a significant cracking tendency during laser powder bed fusion (LPBF) processing, leading to a mismatch between printability and mechanical properties. Modification of alloy compositions is an effective strategy to enhance the printability and mechanical properties of nickel-based superalloys via LPBF. In this study, the effects of adding 5 wt.%Co on the printability and mechanical properties of LPBF-fabricated IN738 were investigated by using three-dimensional high-resolution micro-computed tomography (micro-CT), electron backscatter diffraction (EBSD), and quasi-static room-temperature tensile tests. The results show that adding 5 wt.%Co can significantly reduce the defect rate and defect size of the LPBF-fabricated IN738 alloy, remarkably improve alloy densification, and optimize printability. Meanwhile, compared with the LPBF-fabricated IN738 alloy, the 5 wt.%Co-IN738 alloy exhibits an excellent balance of strength and ductility in horizontal and vertical directions, both LPBF-fabricated and heat-treated. These results are anticipated to offer valuable guidance for the development of LPBF-fabricated Ni-based superalloys that achieve a favorable balance between printability and mechanical properties. Full article

CoCrNi medium-entropy alloys (MEAs) have emerged as a promising class of structural materials due to their exceptional strength–ductility synergy. However, the lack of composition-dependent predictive models severely hinders rational alloy design, forcing reliance on costly trial-and-error experimentation. This study develops a comprehensive theoretical model to predict the yield strength of single-phase face-centered-cubic (FCC) Co_(1-x-y)Cr_yNi_x MEAs by quantitatively evaluating the contributions of grain boundary and solid solution strengthening. The model demonstrates that increasing Cr content significantly enhances grain boundary strengthening through elevated shear modulus and Peierls stress, whereas Ni has a minimal effect. Solid solution strengthening, determined by the minimum resistance among Co–Cr, Co–Ni, and Cr–Ni atomic pairs, peaks at 1726.21 MPa for the composition Co₁₇Cr₆₄Ni₁₉. For equiatomic CoCrNi, theoretical yield strengths range from 1287.8 to 1575.4 MPa across grain sizes of 0.5–50 µm, showing excellent agreement with experimental results. This work provides a reliable, composition-dependent predictive framework that surpasses traditional trial-and-error methods, enabling efficient design of high-strength MEAs through targeted control of lattice distortion and elemental interactions. Full article

To address the technical challenge of balancing formability and strength in automotive aluminum alloys, this study examined an Al-4.35Mg-3.6Zn-0.2Cu alloy subjected to a combined heat-treatment schedule consisting of a two-step solution treatment (470 °C for 24 h followed by 460 °C for 30 min) and a subsequent two-step aging process (T4P: 80 °C for 12 h, followed by BH: 180 °C for 30 min). Microstructural evolution was characterized using transmission electron microscopy, and uniaxial tensile tests were performed in accordance with the GB/T 228.1-2021 standard at a strain rate of 0.2 mm/min. In the T4P condition, the matrix contained both GPI zones (~0.9 nm) and GPII zones (~1.2 nm), with no detectable T-phase precipitation. The presence of GPII zones enhanced ductility by promoting dynamic recovery after dislocation shearing, resulting in a yield strength (YS) of 178 MPa, an ultimate tensile strength (UTS) of 310 MPa, and an elongation (El) of 9%. After BH treatment, the GPII zones transformed into semi-coherent T′-Mg₃₂(AlZnCu)₄₉ precipitates (~2.4 nm), which strengthened the alloy through their semi-coherent interfaces. The retained GPII zones mitigated the loss of ductility, and the final mechanical properties reached a YS of 275 MPa, a UTS of 340 MPa, and an El of 8.5%, corresponding to a BH response of 97 MPa. Strengthening-mechanism calculations indicated that GP zones contributed approximately 120 MPa to the yield strength in the T4P state, whereas T′ precipitates contributed about 169.64 MPa after BH treatment. The calculated values agreed well with the experimental results, with a deviation of less than 3%. This study clarifies the precipitation sequence in the alloy—supersaturated solid solution → GPI zones → GPII zones → T′ phase—and establishes the relationship between microstructure and strength–ductility behavior. The findings provide theoretical guidance for the design and optimization of high-strength, high-formability aluminum alloys for automotive outer-panel applications. Full article

Concrete remains the most widely used construction material globally; however, its intrinsic limitations—low tensile strength, brittle behavior, and susceptibility to microcracking—necessitate performance enhancement for demanding structural applications. Hybrid fiber-reinforced concrete (HFRC) offers a promising solution, yet the optimal balance of steel fibers (SF) and polypropylene fibers (PF) for structural elements such as slabs remains insufficiently understood. This study experimentally investigates the flexural behavior of 42 reinforced concrete slabs (21 one-way and 21 two-way) incorporating systematically varied SF–PF volumetric ratios, advancing current knowledge by identifying performance-optimal hybrid configurations for each slab type. One-way slabs were tested under four-point bending and two-way slabs under three-point bending, with structural responses evaluated in terms of load capacity, cracking behavior, deflection characteristics, and failure modes. The results demonstrate that fiber dosage does not proportionally enhance strength, as excessive content leads to fiber balling and reduced workability—highlighting the need for optimized hybrid proportions rather than indiscriminate addition. Quantitative findings confirm significant performance gains with properly tuned hybrid mixes. For one-way slabs, the optimal combination of 0.7% SF + 0.9% PF achieved 115% of the ultimate load of the control specimen, demonstrating a substantial improvement in flexural resistance. Two-way slabs exhibited even greater enhancements: first-crack load increased by up to 213%, and ultimate load improved by 40.36%, while deflection capacity rose by 44.81% at first crack and 39.80% at ultimate load with the optimal 0.9% SF + 0.1% PF mix. Comparatively, two-way slabs outperformed one-way slabs across all metrics, benefiting from multidirectional stress distribution that enabled more effective fiber engagement. Overall, this study provides new insight into hybrid fiber synergy in RC slabs and establishes quantified optimal SF–PF combinations that significantly enhance load capacity, ductility, and crack resistance for both one-way and two-way systems. Full article

The development of miniaturized, integrated, and flexible thermoelectric devices has intensified the demand for high-performance thermoelectric semiconductors. While significant advances have been made in optimizing their thermoelectric properties, mechanical performance in terms of the strength and ductility has remained a challenge. Consequently, the inherent brittleness and insufficient mechanical robustness of inorganic thermoelectric semiconductors present a major barrier to their commercial applications. Therefore, it is essential to develop thermoelectric materials with enhanced reliability and operational lifespan of flexible thermoelectric devices. This review summarizes recent breakthroughs in low-dimensional thermoelectric materials and emerging defect engineering strategies, which offer promising pathways for simultaneously improving both mechanical and thermoelectrical performance. By precisely regulating the relationship between nanostructural design and performance characteristics, new opportunities are emerging for nanostructured semiconductors in flexible thermoelectric applications across wide temperature ranges, from near-ambient to elevated conditions. Full article

Unsaturated polyester resins (UPRs) were synthesized from camphoric acid and diluted with styrene, partially replaced (up to 30%) by trimethylolpropane triacrylate (TMPTA). Rheological tests showed increased but sustainable viscosity due to TMPTA’s higher polarity. These UPRs served as matrices for composites reinforced with non-woven bamboo and flax mats from recycled waste. Mechanical testing revealed that C_f-UPR/TMPTA30 exhibited the highest tensile strength (25.2 MPa) and modulus (0.96 GPa), compared to 18.7 MPa and 0.74 GPa for the styrene-based resin, respectively, attributed to greater cross-link density. Bamboo composites showed lower tensile properties (13.6 MPa) due to random fiber orientation and porosity, while flax-reinforced systems, especially C_f-UPR/TMPTA30–FLAX, reached 42.7 MPa tensile and 95.5 MPa flexural strength, indicating synergy between TMPTA-modified resin and flax fibers. Dynamic-mechanical analysis confirmed stable thermo-mechanical behavior, and water uptake tests showed reduced absorption (by ~10%), suggesting improved fiber/matrix adhesion. SEM images revealed brittle fracture and fiber pull-out in styrene systems, but fiber breakage and ductile textures in TMPTA-based ones, proving better stress transfer. Thermal analysis indicated slightly earlier degradation onset for TMPTA-modified resins but higher char yield in fiber composites. Overall, TMPTA substitution and flax reinforcement enhance the mechanical, interfacial, and thermal properties of bio-based UPRs, supporting sustainable high-performance composites. Full article

To optimize the microstructure and mechanical properties of Ti6Al4V alloys fabricated via Selective Laser Melting (SLM), this study proposes an optimization approach based on the chessboard scanning strategy. A systematic comparison of three scanning strategies—alternating, stripe, and chessboard scanning—was conducted to examine their effects on thermal input distribution, grain refinement, phase composition, and mechanical performance. Characterization results from Scanning Electron Microscopy (SEM), Electron Backscatter Diffraction (EBSD), and Transmission Electron Microscopy (TEM) revealed that the chessboard scanning strategy effectively refines the grain size to 88.64 ± 10.79 μm and increases the strengthening phase α′ content to 53.3%. Mechanical testing showed a tensile strength of 1179 ± 17 MPa (11.02% higher than stripe scanning) and elongation of 7.9 ± 0.4%. This strategy promotes random grain orientation by altering the scanning path, disrupting directional solidification, and suppressing texture formation. Microstructural mechanism analysis suggests that dislocation strengthening, increased α′ content, and grain refinement synergistically enhance both strength and ductility. These findings provide theoretical support for optimizing SLM parameters and the design of Ti6Al4V alloys’ microstructure and mechanical properties. Full article

The network architecture has demonstrated considerable potential for enhancing the strength–ductility synergy in metal matrix composites (MMCs). Intuitively, the intersections of network layers are expected to induce a stress concentration, leading to premature brittle fractures. Introducing chamfers to round the network cells may mitigate the local stress concentration and thereby improve elongation. Here, a numerical simulation framework was developed to investigate the effect of chamfering on the mechanical behavior of a three-dimensional (3D) continuous SiC_3D/Al composite with a network architecture. A Voronoi tessellation algorithm was employed to generate the continuous network structural SiC phase. By inducing ductile and brittle damage criterions in the matrix and reinforcement elements, respectively, the mechanical behavior can be predicted via the finite element method (FEM). The predicted mechanical properties reveal an unexpected trend: chamfering results in a simultaneous reduction in both strength (from 367 MPa to 312 MPa) and elongation (from 4.1% to 2.0%). With chamfering, the enlarged intersection of the network layer bears a lower load, whereas the narrower network plates exhibit higher stress concentrations. As a result, the overall load-bearing capacity of the SiC_3D reinforcement decreases monotonically with an increasing chamfer size f. Furthermore, the non-uniform stress distribution promotes the premature fracture of the SiC_3D, which reduces elongation. Additionally, the crack deflection behavior is suppressed in the chamfered models, leading to decreasing energy dissipation. This unanticipated outcome highlights an important architectural design principle: maintaining uniform geometric dimensions is critical for achieving optimal composite performance. Full article

In this study, a biodegradable Mg-Zn-Nd-Gd alloy was processed via multi-directional forging (MDF) to evaluate its microstructural evolution, mechanical performance, and corrosion behavior. Electron backscattered diffraction (EBSD) analysis was conducted to evaluate the influence of grain size and texture on mechanical strength and corrosion resistance. The average grain size decreased significantly from 118 ± 5 μm in the homogenized state to 30 ± 10 μm after six MDF passes, primarily driven by discontinuous dynamic recrystallization (DDRX). Remarkably, this magnesium (Mg) alloy exhibited a rare synergistic enhancement in both strength and ductility, with ultimate tensile strength (UTS) increasing by ~59%, yield strength (YS) by ~90%, while elongation improved by ~44% unlike conventional severe plastic deformation (SPD) techniques that often sacrifice ductility for strength. This improvement is attributed to grain refinement, dispersion strengthening from finely distributed Mg₁₂Nd and Mg₇Zn₃ precipitates, and texture weakening, which facilitated the activation of non-basal slip systems. Despite the mechanical improvements, electrochemical corrosion testing in Hank’s balanced salt solution (HBSS) at 37 °C revealed an increased corrosion rate from 0.1165 mm/yr in homogenized condition to 0.2499 mm/yr (after six passes of MDF. This was due to the higher fraction of low-angle grain boundaries (LAGBs), weak basal texture, and the presence of electrochemically active fine Mg₇Zn₃ particles. However, the corrosion rate remained within the acceptable range for bioresorbable implant applications, indicating a favorable trade-off between mechanical performance and degradation behavior. These findings demonstrate that MDF processing effectively enhances the strength–ductility synergy of Mg-rare earth alloys while maintaining a clinically acceptable degradation rate, thereby presenting a promising route for next-generation biomedical implants. Full article

Magnesium (Mg) alloys are prized as the lightest structural materials but often suffer from a strength–ductility trade-off that is particularly challenging for applications demanding high thermal conductivity. Aiming to resolve this issue, rolled ternary Mg-0.9Mn-1.9Ce (wt.%) alloy sheets were designed and fabricated, and the influence of rolling strain on optimizing the property balance was systematically investigated. The cast alloy was homogenized and rolled to two accumulated strains to obtain S10 (90%) and S20 (95%), followed by microstructure characterization and mechanical/thermal evaluation. Compared with S10, S20 developed finer, more equiaxed grains and a weaker basal texture via enhanced dynamic recrystallization; concurrent fragmentation and uniform dispersion of second-phase particles further contributed to strengthening. Consequently, S20 achieved 14.2% and 13.7% increases in yield and tensile strengths, respectively, with a slight improvement in elongation, while retaining high thermal conductivity (134.4 W·m⁻¹·K⁻¹ vs. 138.1 W·m⁻¹·K⁻¹ for S10). The minimal conductivity penalty is attributed to the low solute level in the α-Mg matrix, which limits electron scattering. These results provide experimental and mechanistic guidance for developing rolling Mg alloys that combine high mechanical performance with excellent thermal efficiency. Full article

A Y-doped AlCoCrFeNi_2.1 eutectic high-entropy alloy was fabricated via powder bed fusion-laser melting/metal (PBF-LB/M), and the effects of the rare-earth element Y on its microstructure and mechanical properties were investigated. The results indicate that Y addition preserves the fine eutectic microstructure inherent to the PBF-LB/M process, while inducing lattice distortion within the face-centered cubic (FCC) matrix and promoting grain refinement. During solidification, Y facilitates heterogeneous nucleation and, due to its strong affinity with Al, increases both the volume fraction of the body-centered cubic (BCC) phase and the proportion of high-angle grain boundaries. X-ray diffraction (XRD) analysis further confirms that Y suppresses the formation of the ordered B2 phase. Tensile testing reveals that Y doping improves the tensile strength from 1383 MPa to 1475 MPa and enhances the elongation from 13.0% to 16.3%. Fractography shows a transition from quasi-cleavage to ductile fracture mode, indicating that Y significantly enhances the strength–ductility synergy of the alloy. Full article

In additively manufactured (AM) Ti-6Al-4V, the role of martensitic α′ in governing brittleness versus toughness remains debated, largely because complex thermal histories and other intertwined physical factors complicate interpretation. To isolate and clarify the intrinsic effect of cooling rate, we employed a Gleeble thermal simulator, which enables precisely controllable cooling rates while simultaneously achieving ultra-fast quenching comparable to AM (up to ~7000 °C/s). By varying the cooling rate only, three distinct microstructures were obtained: α/β, α_m/α′, and fully α′. Compression tests revealed that the ultra-fast-cooled fully martensitic Ti-6Al-4V attained both higher strength and larger fracture strain, with densely distributed elongated dimples indicative of ductile failure. Three-dimensional microstructures reconstructed from microscopy, analyzed using an EVP-FFT crystal plasticity model, demonstrated that refined α′ laths and abundant high-angle boundaries promote more homogeneous strain partitioning and reduce stress triaxiality, thereby delaying fracture. These results provide potential evidence that extreme-rate martensitic transformation can overcome the conventional strength–ductility trade-off in Ti-6Al-4V, offering a new paradigm for processing titanium alloys and AM components with superior performance. Full article

In-situ lunar construction technology is critical for future lunar base development, and the production of geopolymers from lunar regolith—a novel cementitious material with concrete-like properties—has become a vital approach for achieving in-situ resource utilization. This study systematically investigated the influence of basalt fiber content (0–0.4%) on the mechanical properties of lunar regolith simulant geopolymers by controlling key parameters including curing temperature (20 °C and 80 °C), duration (1 d and 7 d), and alkali activator type (strong alkaline solution: a mixture of sodium hydroxide and sodium silicate, and weak alkaline solution: sodium silicate solution). Through testing of 144 specimens, the results revealed that strong alkali-activated specimens with 0.3% fibers cured at 20 °C for 7 d showed optimal ductility with compressive strength of 2.85 MPa and flexural strength of 0.53 MPa, exhibiting characteristic flat stress-strain curves. Specimens with 0.2% fibers under high-temperature curing at 80 °C for 1 d achieved maximum compressive strength of 44.76 MPa and flexural strength of 1.60 MPa but demonstrated brittle failure behavior. Weak alkali-activated specimens containing 0.1% fibers cured at 80 °C for 7 d attained superior comprehensive performance with peak flexural strength reaching 3.88 MPa, showing excellent fiber-matrix synergy. These findings provide important theoretical foundations for optimizing lunar construction materials through customized fiber reinforcement and curing strategies. Full article

Steel–timber composite (STC) structures offer a sustainable and low-carbon structural solution. Steel–timber interface behavior is critical for the mechanical performance of STC structures. This paper introduces a novel connection for steel–timber composites (STC) that combines mechanical interlocking with adhesive bonding through an epoxy-bonded bolted design. Epoxy resin is injected into the timber dowel slots, followed by pre-tightening of the bolts, forming a composite dowel system where the ‘bolt–epoxy resin–timber’ components work in synergy. The load–displacement characteristics and failure modes of nine specimen groups were investigated through a series of double-shear push-out tests. The influence of a wide range of connector parameters on the stiffness, shear bearing capacity, and ductility of STC joints was systematically investigated. The parameters included fastener strength grade, thread configuration, diameter, number, and the use of epoxy resin reinforcement. The experimental results demonstrated that high-strength partially threaded bolts were crucial for achieving a synergy of high load-bearing capacity and commendable ductility, while full-threaded bolts exhibited vulnerability to brittle shear failure, a consequence of stress concentration at the root of the threads. Although screw connections provided enhanced initial stiffness through timber anchorage, ordinary bolt connections exhibited superior ultimate load-bearing capacity. In comparison with conventional bolt connections, epoxy resin–bolt connections exhibited enhanced mechanical properties, with an augmentation in ultimate load and initial stiffness of 12% and 11.8%, respectively, without sacrificing ductility. Full article

Lightweight aluminum matrix composites with superior strength and structural integrity are in high demand for next-generation transportation and aerospace applications. In this work, Al6060-based composites reinforced with ≈2 wt.% TiB₂ were produced using a hybrid processing route that combines ultrasonically assisted stir casting with radial-shear rolling (RSR). This strategy enabled uniform particle dispersion, strong matrix–reinforcement bonding, and substantial microstructural refinement (grain size 4–6 μm) with reduced porosity. Consequently, the Al6060/TiB₂ composites demonstrated substantial gains over the as-cast alloy, combining a yield strength of 108.6 MPa, ultimate tensile strength of 156.9 MPa, and microhardness of 76.3 HV0.2 with a balanced ductility of ~9%. The demonstrated synergy of ultrasound-assisted casting and severe plastic deformation highlights a scalable pathway for fabricating high-performance aluminum composites, positioning them as promising candidates for aerospace, automotive, and other advanced engineering sectors. Full article