Search Results (177)

As a densely populated area, college student dormitories consume a large amount of electricity every year to heat the domestic hot water used by students. Applying solar energy to hot water systems can effectively alleviate this situation. This paper first conducts a simulation of the hot water load and the calculation of the available area of the solar roof in a dormitory building of a certain university. Then, different solar-coupled air source heat pump systems were designed, and simulation models of the two systems were established. The thermal performance parameters and solar energy utilization of the two systems were discussed, and the energy efficiency, economy, and environmental protection of the two systems were analyzed. The results show that after coupling with the solar collector, the system operation time is shortened by 26.2%, the annual performance coefficient is 3.4, which is 0.8 higher than that of the original system, and the annual heating energy consumption is reduced by 24.4%. In contrast, the annual energy self-sufficiency rate of the photovoltaic coupled with air source heat pump system is 94.6%, achieving nearly zero energy consumption for heating. Full article

China’s urban residential building stock is extensive and spans a wide range of construction periods. With the continuous enhancement of building energy efficiency standards, the chronological characteristics and variability of residential building envelopes are evident. Through field research and typological analysis of residential buildings in Jinan, a cold region of China, three construction eras were classified: Period I (1980–1985), Period II (1986–1995), and Period III (1996–2005). Building performance and economic benefits across these periods are modeled using Rhino 7.3 and Grasshopper. The NSGA-II algorithm, as the core of Wallacei2.7, is employed for multi-objective optimization. Through K-means clustering, TOPSIS comprehensive ranking, and Pearson correlation analysis, the optimized processes and solutions are provided for urban residential renovation decisions in different periods and target preferences. The results show that the optimal comprehensive performance solutions for Period I, Period II, and Period III achieve energy savings of 40.92%, 29.62%, and 15.81%, respectively, and increase annual indoor comfort hours by 872.64 h/year, 633.57 h/year, and 564.11 h/year. For Period I and II residential buildings, the most effective energy efficiency retrofit measures include increasing exterior wall and roof insulation, replacing exterior window types, and reducing exterior window k-value. The overall trend in energy savings rates and economic benefits across the three periods shows a decline. For Period III residential buildings, systematic strategies, such as solar thermal collector systems and photovoltaic technology, are required to enhance energy efficiency. Full article

Concentrating photovoltaic-thermal (CPVT) collectors use reflective surfaces to focus sunlight onto a smaller receiver area, increasing thermal energy output while maintaining annual energy efficiency. Ray-tracing simulations are employed in this study using Tonatiuh to optimise the characteristics of the Double MaReCo (DM) collector, which is an improved version of the commercially available Solarus Power Collector (PC). Focused on enhancing electrical performance, the photovoltaic (PV) cell configurations are varied on the bottom side of the receiver, while the top-side PV cells remain constant. The study also analyses the influence of diodes and transparent gables on the annual solar irradiance received by the PV cells. From the analysis, it is observed that the specific annual irradiance received by the PV cells in the DM collector with transparent gables is nearly 64% more compared to that of the PC counterpart. It is also observed that the transparency of gables becomes significant only when the whole area of the receiver is covered by PV cells. With the goal of improving performance while lowering the cost and complexity of the DM collector, the study investigates various collector design characteristics that may shed more light on optimising the current model. Full article

The purpose of the study is to investigate the energy performance of a PVT collector in combination with a heat pump. First, a test system combining a heat pump and PVT module is built, and then its performance is carefully measured, assessing the electricity and heat production. The paper focuses on increasing the efficiency of a photovoltaic (PV) panel (as part of the PVT module) by cooling it with a heat pump. The main idea is to use the heat generated by the warming panels as a low-temperature source for the heat pump. The research aims to maximize the use of solar energy in the form of both electricity and heat. In traditional PV systems, the panel temperature rise reduces the solar-to-electric conversion efficiency. Therefore, cooling with a heat pump is increasingly used to keep panels at optimal temperatures and improve performance. The tests confirm that cooling the panels with a heat pump results in an 11.4% improvement in electrical efficiency, an increase from 10.8% to 12.0%, with an average system efficiency of 11.81% and a temperature coefficient of –0.37%/°C. The heat pump achieves a COP of 3.45, while thermal energy from the PVT panel accounts for up to 60% of the heat input when the air exchanger is off. The surface temperature of the PVT panels varies from 11 °C to 70 °C, and cooling enables an increase in electricity yield of up to 20% during sunny periods. This solution is especially promising for facilities with year-round thermal demand (e.g., swimming pools, laundromats). Full article

Steam is widely used in industry as a heat carrier for thermal processes and is primarily generated by gas-fired steam boilers. The decarbonization of industrial thermal demand relies on the capability of clean and renewable technologies to provide steam through reliable and cost-effective systems. Concentrating solar thermal technologies are attracting attention as a heat source for industrial steam generation. In addition, electricity-driven high-temperature heat pumps can provide heat using either renewable or grid electricity by upgrading ambient or waste heat to the required temperature level. In this study, linear Fresnel solar collectors and high-temperature heat pumps driven by photovoltaics are considered heat sources for steam generation in industrial processes. Energetic and economic analyses are performed across the European countries to assess and compare their performances. The results demonstrate that for a given available area for the solar field, solar thermal systems provide a higher annual energy yield in southern countries and at lower costs than heat pumps. On the other hand, heat pumps driven by photovoltaics provide higher annual energy for decreasing solar radiation conditions (central and northern Europe), although it leads to higher costs than solar thermal systems. A hybrid scheme combining the two technologies is the favorable option in central Europe, allowing a trade-off between the costs and the energy yield per unit area. Full article

Cooking food is a factor that contributes to global energy consumption and greenhouse gas emissions. This research proposes the design, simulation using thermal resistances with MATLAB Simulink, and experimental evaluation of an automated double-concentrated solar cooking system operable from inside a home. Water was used as a cooking load. Each test for 25 min was entered into a system integrated by a programmable elevator to transport the food to the roof, a configurable temperature display, a photovoltaic power source, and double solar collection (direct through a modified box oven and reflected by a parabolic dish collector). When both solar components operated simultaneously, the system reached a temperature of 79 °C, representing a 57.34 °C increase. On average, the solar concentrator provided 78.02% more energy than the oven alone. This approach is expected to reduce cooking time and contribute to sustainable home design aimed at mitigating greenhouse gas emissions. Full article

The implementation of renewable energy systems (RESs) in the agricultural sector has significant potential to mitigate the negative effects of fossil fuel-based products on the global climate, reduce operational costs, and enhance crop production. However, the intermittent nature of RESs poses a major challenge to realizing these benefits. To address this, thermal energy storage (TES) and hybrid heat pump (HHP) systems are integrated with RESs to balance the mismatch between thermal energy production and demand. In pursuit of clean energy solutions in the agricultural sector, a 3942 m² greenhouse in Yeoju-si, South Korea, is equipped with 231 solar thermal (ST) collectors, 117 photovoltaic thermal (PVT) collectors, four HHPs, two ground-source heat pumps (GSHPs), a 28,500 m³ borehole TES (BTES) unit, a 1040 m³ tank TES (TTES) unit, and three short-term TES units with capacities of 150 m³, 30 m³, and 30 m³. This study evaluates the long-term performance of the integrated hybrid renewable energy and thermal energy storage systems (HRETESSs) in meeting the greenhouse’s heating and cooling demands. Results indicate that the annual system performance efficiencies range from 25.3% to 68.5% for ST collectors and 31.9% to 72.2% for PVT collectors. The coefficient of performance (COP) during the heating season is 3.3 for GSHPs, 2.5 for HHPs using BTES as a source, and 3.6 for HHPs using TTES as a source. During the cooling season, the COP ranges from 5.3 to 5.7 for GSHPs and 1.84 to 2.83 for ASHPs. Notably, the HRETESS supplied 3.4% of its total heating energy directly from solar energy, 89.3% indirectly via heat pump utilization, and 7.3% is provided by auxiliary heating. This study provides valuable insights into the integration of HRETESSs to maximize greenhouse energy efficiency and supports the development of sustainable agricultural energy solutions, contributing to reduced greenhouse gas emissions and operational costs. Full article

The present study focuses on the development, thermodynamic evaluation, and economic analysis of a photovoltaic-thermal (PVT)-based automated mixed-mode indirect solar dryer (AMMISD). The developed AMMISD was used for drying five date varieties native to the Aswan area, namely Shamia, Bartamuda, Sakkoti, Malkabii, and Gondaila. The initial and final moisture contents of date varieties ranged between 15.7% and 17.2% and 4.91% and 6.41%, respectively. All date fruit varieties reached equilibrium moisture content after 6 days (60 h) compared with 14 days (140 h) in a traditional indirect solar dryer (SD) and 14–25 days (140–250 h) under open-air sun drying. The energy analysis of both the solar air collector (SAC) and the SD showed that the SAC efficiency and the drying efficiency were in the range of 15.15–63.33% and 4.01–4.41%, respectively. Additionally, the exergy analysis of the SAC and drying room (DR) revealed a maximum efficiency of 27.5% and 96.62%, respectively. The improvement potential (IP) ranged from 4.62 to 13.64 W, the mean value of waste exergy ratio (WER) was 0.84, and the sustainability index (SI) ranged from 1.01 to 1.38. Moreover, the economic analysis showed substantial economic advantages for date fruit drying, yielding annual savings of approximately USD 236.9, with an investment recovery period of about 2.091 years. Full article

The industrial sector’s movement toward decarbonization is regarded as essential for governments. This paper assesses a system that uses only solar energy to synthesize liquid hydrogen and ammonia as energy carriers. Photovoltaic modules deliver electrical power, while parabolic dish collectors are responsible for directing thermal energy to the solid oxide electrolyzer for hydrogen production, which then mixes with nitrogen to produce ammonia after a number of compression stages. To investigate the proposed system, comprehensive thermodynamic and exergo-economic studies are performed using an engineering equation solver and ASPEN PLUS software. Full article

Over the past few years, the combination of solar power with refrigeration technology has matured, providing a promising solution for sustainable cooling. However, a key challenge remains, namely the inherent intermittency of solar energy. Due to its uneven temporal distribution, it is difficult to ensure continuous 24 h operation when relying solely on solar energy. To address this issue, thermal energy storage technology has emerged as a viable solution. This paper presents a comprehensive systematic review of phase-change material (PCM) applications in solar refrigeration systems. It systematically categorizes solar energy conversion methodologies and refrigeration system configurations while elucidating the fundamental operational principles of each solar refrigeration system. A detailed examination of system components is provided, encompassing photovoltaic panels, condensers, evaporators, solar collectors, absorbers, and generators. The analysis further investigates PCM integration strategies with these components, evaluating integration effectiveness and criteria for PCM selection. The critical physical parameters of PCMs are comparatively analyzed, including phase transition temperature, latent heat capacity, specific heat, density, and thermal conductivity. Through conducting a critical analysis of existing studies, this review comprehensively evaluates current research progress within PCM integration techniques, methodological classification frameworks, performance enhancement approaches, and system-level implementation within solar refrigeration systems. The investigation concludes by presenting strategic recommendations for future research priorities based on a comprehensive systematic evaluation of technological challenges and knowledge gaps within the domain. Full article

Electrification is a key priority of the European Union, focusing on saving energy resources and mitigating carbon emissions through enhancing restrictions on relative policies and initiatives. For such goals to be achieved, investing in renewable energy technologies on large- and small-scale projects is promoted. These efforts were implemented in the building sector too, highlighting the importance of optimal decisions in improving the energy performance of buildings, from an economic, energy and environmental perspective. In this context, this paper aims to elaborate a decision-making methodology for building thermal design, considering the optimal selection and operation of multi-energy systems focused on renewable technologies. Solar thermal collectors, photovoltaic systems and heat pumps were included in an Energy Hub for meeting the heating, cooling and domestic hot water energy demand. Optimal decisions were achieved by formulating Mathematical Programming models in GAMS, for minimizing economic, energy and environmental parameters of the systems under a life cycle perspective. The proposed methodology was implemented in a residential building case study. Results show that combining heat pumps with photovoltaics is preferable for all of the examined criteria, while a sensitivity analysis of the economic, energy and environmental parameters, influencing the energy mixture, leads to optimal solutions with the participation of different energy systems. Full article

This paper reviews recent advancements in integrated thermoelectric power generation and water desalination technologies, driven by the increasing global demand for electricity and freshwater. The growing population and reliance on fossil fuels for electricity generation pose challenges related to environmental pollution and resource depletion, necessitating the exploration of alternative energy sources and desalination techniques. While thermoelectric generators are capable of converting low-temperature thermal energy into electricity and desalination processes that can utilize low-temperature thermal energy, their effective integration remains largely unexplored. Currently available hybrid power and water systems, such as those combining conventional heat engine cycles (e.g., the Rankine and Kalina cycles) with reverse osmosis, multi-effect distillation, and humidification–dehumidification, are limited in effectively utilizing low-grade thermal energy for simultaneous power generation and desalination, while solid-state heat-to-work conversion technology, such as thermoelectric generators, have low heat-to-work conversion efficiency. This paper identifies a key research gap in the limited effective integration of thermoelectric generators and desalination, despite their complementary characteristics. The study highlights the potential of hybrid systems, which leverage low-grade thermal energy for simultaneous power generation and desalination. The review also explores emerging material innovations in high figure of merit thermoelectric materials and advanced MD membranes, which could significantly enhance system performance. Furthermore, hybrid power–desalination systems incorporating thermoelectric generators with concentrated photovoltaic cells, solar thermal collectors, geothermal energy, and organic Rankine cycles (ORCs) are examined to highlight their potential for sustainable energy and water production. The findings underscore the importance of optimizing material properties, system configurations, and operating conditions to maximize efficiency and output while reducing economic and environmental costs. Full article

Membrane distillation (MD) is an evolving thermal separation technique most frequently aimed at water desalination, compatible with low-grade heat sources such as waste heat from thermal engines, solar collectors, and high-concentration photovoltaic panels. This study presents a comprehensive theoretical–experimental evaluation of three commercial membranes of different materials (PE, PVDF, and PTFE), tested for two distinct MD modules—a Direct Contact Membrane Distillation (DCMD) module and an Air Gap Membrane Distillation (AGMD) module—analyzing the impact of key operational parameters on the performance of the individual membranes in each configuration. The results showed that increasing the feed saline concentration from 7 g/L to 70 g/L led to distillate flux reductions of 12.2% in the DCMD module and 42.9% in the AGMD one, averaged over the whole set of experiments. The increase in feed temperature from 65 °C to 85 °C resulted in distillate fluxes up to 2.36 times higher in the DCMD module and 2.70 times higher in the AGMD one. The PE-made membrane demonstrated the highest distillate fluxes, while the PVDF and PTFE membranes exhibited superior performance under high-salinity conditions in the AGMD module. Membranes with high contact angles, such as PTFE with 143.4°, performed better under high salinity conditions. Variations in operational parameters, such as flow rate and temperature, markedly affect the temperature and concentration polarization effects. The analyses underscored the necessity of a careful selection of membrane type for each distillation configuration by the specific characteristics of the process and its operational conditions. In addition to experimental findings, the proposed heat and mass transfer-reduced model showed good agreement with experimental data, with deviations within ±15%, effectively capturing the influence of operational parameters. Theoretical predictions showed good agreement with experimental data, confirming the model’s validity, which can be applied to optimization methodologies to improve the membrane distillation process. Full article

Improving solar availability in urban blocks is vital to promoting energy conservation and emissions reduction. However, there are very few studies on the impact of block morphology on solar energy availability in high-density cities based on the particularities of climate and solar energy resources in severe cold regions at higher latitudes. This study took 434 block models generated through seven orientation conditions of 62 residential blocks in Harbin, China, as its research object. Through numerical simulations and statistical analysis, it revealed the quantitative relationship between block morphology and the availability of active photovoltaic and solar thermal collector technologies and passive thermal heating technologies. The results show that active solar technology has the highest availability in multi-story enclosed residential blocks, and passive thermal heating has the highest availability in the multi-high-level mixed-row type. The south façade of the building has the greatest active and passive solar availability. The overall active solar availability of the residential block is significantly negatively correlated with the mean building height, floor area ratio, and volume area ratio; it is significantly positively correlated with site coverage and the standard deviation of the building height. Controlling the block’s orientation between 15° south by west and 15° south by east can increase the active solar availability of the façade. This study provides a reference and evaluation basis for the sustainable planning and design of high-density cities in severely cold regions. Full article

Promoting complete decarbonization by entrusting the energy supply through renewable sources (wind, photovoltaic, solar thermal, etc.) is one of the key strategies in the building sector. However, renewable energy’s intermittent and space–time mismatch characteristics pose challenges to its compatibility with the power grid. Challenges can be mitigated by introducing thermal and electrical storage to increase the self-consumption of renewable energy in the buildings. This work proposes a comparison between different energy systems equipped with a heat pump, solar plant (photovoltaic or photovoltaic thermal), and thermal and electrical storage. All year-round performances of the different energy system configurations have been simulated using the TRNSYS 17.2 software. The energy analyses revealed that the energy system equipped with a photovoltaic plant, when incorporating the two storages, improves self-consumption (Rsc) from 34.1% to 69.4 and self-sufficiency (Dss) from 27.9% to 59.9%, respectively. Additionally, the energy system equipped with photovoltaic thermal collectors and both storages further improve the system performance; an Rsc of 96.2% and Dss of 86.9% are attained. These results demonstrate that the previous energy system configuration can facilitate the near attainment of net-zero energy buildings. Furthermore, the proposed energy system is characterized by a minimal energy imbalance between the building’s energy demand and the energy produced, thereby reducing the need for energy exchange with the electrical grid. Full article