Search Results (412)

Ceramic pastes used in additive manufacturing offer several advantages, including low production costs due to the availability of raw materials and efficient processing methods, as well as a reduced environmental footprint through minimized material waste, optimized resource use, and the inclusion of recyclable or sustainably sourced components. This study evaluates the effect of diatomite content in a ceramic paste composed of carboxymethyl cellulose, kaolinite, and feldspar on its extrusion behavior and thermal conductivity, with additional analysis of its implications for microstructure, mechanical properties, and thermal performance. Four ceramic pastes were prepared with diatomite additions of 0, 10, 30, and 60% by weight. Thermal conductivity, extrusion behavior, morphology, and distribution were examined using scanning electron microscopy (SEM), while thermal degradation was assessed through thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results show that increasing diatomite content leads to a reduction in thermal conductivity, which ranged from 0.719 W/(m·°C) for the control sample to 0.515 W/(m·°C) for the 60% diatomite sample, as well as an improvement in extrusion behavior. The ceramic paste demonstrated adequate extrusion performance for 3D printing at diatomite contents above 30%. These findings lay the groundwork for future research and optimization in the development of functional ceramic pastes for advanced manufacturing applications. Full article

To remove nickel (II) from an aqueous solution, cellulose nanocrystals (CNCs) were modified as an adsorbent. The FTIR and SEM were used to characterise the properties of CNCs. In addition to how well they predicted reaction (adsorption capacity), the central composite design was used. The response surface model method performs well, according to statistical data. Four operational variables were studied: The initial concentration of the nickel (II) solution in mg/L, the pH, the contact period in minutes, and the adsorbent dose in g/100 mL. The removal percentage (%) was the result. The percentage removal was 98% after 178 min of contact, a starting concentration of 110 mg/L, an adsorbent dosage of 9.3 g, and an initial pH of 3.5. The R² was 0.996, the adjusted R² was 0.921, and the predicted R² was 0.945. The quadratic equation was determined using central composite design. The FTIR examination revealed that the functional groups, hydroxyl groups (OH), peaked around 3300–3500 cm^−1, and carboxyl groups (COOH) peaked around 1700 cm⁻¹. Full article

Traditional stabilization techniques, such as lime and cement, widely used for their effectiveness, albeit with economic and environmental limitations, are leading to the search for sustainable approaches that utilize agricultural and industrial waste, such as rice husk ash, bagasse, and natural fibers. These have been shown to improve key geotechnical properties, even under saturated conditions, significantly. In particular, the combination of rice husk ash and recycled ceramics has shown notable results in Ecuadorian coastal soils. The article emphasizes the importance of selecting techniques that balance effectiveness, cost, and sustainability and identifies existing limitations, such as the lack of long-term data (ten years) and predictive models adapted to the Ecuadorian climate. From a bibliographic perspective, this article analyzes the challenges posed by expansive soils in the western coastal region of Ecuador, whose high plasticity and instability to moisture negatively affect civil works such as roads and buildings. The Ecuadorian clay contained 30% kaolinite and only 1.73% CaO, limiting its chemical reactivity compared to soils such as Saudi Arabia, which contained 34.7% montmorillonite and 9.31% CaO. Natural fibers such as jute, with 85% cellulose, improved the soil’s mechanical strength, increasing the UCS by up to 130%. Rice husk ash (97.69% SiO₂) and sugarcane bagasse improved the CBR by 90%, highlighting their potential as sustainable stabilizers. All of this is contextualized within Ecuador’s geoenvironmental conditions, which are influenced by climatic phenomena such as El Niño and La Niña, as well as global warming. Finally, it is proposed to promote multidisciplinary research that fosters more efficient and environmentally responsible solutions for stabilizing expansive soils. Full article

The efficient use of renewable lignocellulosic biomass has attracted wide interest, as it promises to reduce the environmental impact of fossil fuel consumption. A recently developed batch-scale process, which produces glycol lignin (GL) from softwood biomass, generates a considerable amount of cellulose-rich solid residues (SRs) as a byproduct. In this study, usable cellulose was isolated from SRs in the form of carboxylated cellulose nanocrystals (O-CNCs). The properties of O-CNCs were investigated to establish a possible integrated biomass utilization system based on the GL production technology. Three different forms of purified SRs—never-dried (N-Cel), freeze-dried (F-Cel), and vacuum-dried (V-Cel) cellulose—were subjected to oxalic acid (OA) hydrolysis at 95 °C for 4 h. The average length of O-CNCs ranged from 90 to 120 nm and the height ranged from 3 to 6 nm for separate particles and from 8 to 20 nm for aggregates. The carboxyl group content was 0.11–0.23 mmol/g O-CNCs. The overall results indicated that the yields, dimensions, surface charges, and thermal stability of the O-CNCs were largely influenced by the nature of the starting cellulose. In addition, O-CNCs prepared from recycled OA exhibited similar properties to those prepared from fresh OA. Full article

The rising demand for sustainable energy storage has fueled the development of green batteries as alternatives to conventional systems. However, a major research gap lies in the unified integration of environmentally friendly materials and processes across all battery components—electrodes, electrolytes, and separators—without compromising performance or scalability. This review addresses this gap by highlighting recent advances in eco-conscious battery technologies, focusing on green electrode fabrication using water-based methods, electrophoretic deposition, solvent-free dry-press coating, 3D printing, and biomass-derived materials. It also examines the shift toward safer electrolytes, including ionic liquids, deep eutectic solvents, water-based systems, and solid biopolymer matrices, which improve both environmental compatibility and safety. Additionally, biodegradable separators made from natural polymers such as cellulose and chitosan offer enhanced thermal stability and ecological benefits. The review emphasizes the importance of lifecycle considerations like recyclability and biodegradability, aligning battery design with circular economy principles. While significant progress has been made, challenges such as standardization, long-term stability, and industrial scalability remain. By identifying key strategies and future directions, this article contributes to the foundation for next-generation green batteries, promoting their adoption in environmentally sensitive applications ranging from wearable electronics to grid storage. Full article

Bio-based polydithioacetal nanocomposites were synthesized to address the critical need for materials that simultaneously achieve enhanced thermomechanical properties and excellent reprocessing capabilities. Using vanillin and cellulose nanocrystals (CNCs) as starting materials, linear polydithioacetals (PDTAs) were prepared via acid-catalyzed polycondensation of vanillin with various dithiols including 1,6-hexanedithiol, 1,10-decanedithiol, 3,6-dioxa-1,8-octanedithiol and 2,2′-thiodiethanethiol. These PDTAs were then crosslinked with a diepoxide (i.e., diglycidyl ether of bisphenol A, DGEBA) via the reaction of phenolic hydroxyl groups of PDTAs with epoxide groups of DGEBA. To create the nanocomposites, cellulose nanocrystals (CNCs) were surface-functionalized with thiol groups and then incorporated as the reinforcing nanofillers of the networks. The results of morphological observation showed that the fine dispersion of CNCs in the polymer matrix was attained. Owing to the incorporation of CNCs, the nanocomposites displayed improved thermomechanical properties. Compared to the network without CNCs, the nanocomposite containing 20 wt% CNCs exhibited an increase of more than tenfold in modulus and threefold in tensile strength. In addition, the nanocomposites exhibited excellent reprocessing properties, attributable to the dynamic exchange of dithioacetal bonds. This work presents a promising strategy for developing bio-based nanocomposites that have not only improved thermomechanical properties but also excellent reprocessing (or recycling) properties. Full article

Because of their many health benefits, blueberries are highly sought after as superfoods. There are also ongoing initiatives to enhance sustainability in blueberry packaging by selecting appropriate materials. Ideal packaging should ensure the safe delivery of the fruit to consumers while maintaining product quality, addressing environmental concerns, and promoting circularity. The environmental impact of four different packaging materials was assessed using a comparative cradle-to-grave life cycle assessment. The materials evaluated included a cardboard package (CB), a cardboard package with a cellulose lid (CBC), a polypropylene (PP) as a control, and a punnet made from rice straw topped with polylactic acid (RPLA), a bio-based plastic. The evaluation considered all environmental impact categories, utilizing Sphera GaBi software and the CML 2016 method. Special attention was given to various end-of-life scenarios, determining energy resources and fossil abiotic depletions. The results indicate that RPLA is the most eco-friendly option, with the lowest carbon footprint and energy resources. CB has a larger carbon footprint but less overall impact than traditional incineration, while CBC has the highest impact during recycling, mainly due to marine ecotoxicity. PP has a relatively low impact on energy resources and fossil abiotic depletion compared to CB and CBC packaging materials. Full article

A cellulose-based material with high adsorption capacity and surface area was developed by selecting appropriate copolymer monomers for structural design. This material was used for selective dye adsorption in wastewater treatment. The copolymer was characterized by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and Fourier-transform infrared spectroscopy (FTIR) to investigate its microstructure, structure, thermal stability, and thermal decomposition. We explored the factors affecting dye adsorption, including dye type, adsorption reaction time, initial dye concentration, copolymer dosage, temperature, and the acidity or alkalinity of the reaction environment. The results showed that as the adsorption reaction time increased, the amount of adsorbed Rhodamine B dye gradually increased, and the initial stage (0–20 min) increased rapidly. When the initial dye concentration was 15 mg/L, the adsorption capacity (q_e) was at its maximum (3.67 mg/g). In addition, when the amount of copolymer used was 5 mg/10 mL, the adsorption capacity (q_e) was the highest (12.37 mg/g). High-temperature conditions were favorable for adsorption, with the maximum adsorption capacity (q_e) at 35 °C (13.48 mg/g). The prepared copolymer exhibited significant adsorption performance in acidic environments (pH = 3). The polymer adsorbed with dye was degraded by UV irradiation, avoiding secondary pollution caused by recycling. Full article

The increasing market demand and rising costs of raw materials have intensified interest in renewable and sustainable sources. As a result, the production of building-block chemicals from natural products or synthetic feedstocks has driven scientific research toward catalytic strategies for the depolymerization of these materials. Polymer chemistry offers significant opportunities for recycling, as polymer synthesis typically begins with monomeric units. Emerging non-destructive techniques now allow for the recovery of these original reagents. This review summarizes recent advances in catalytic methods for the depolymerization of polymers derived from both natural sources, such as cellulose and lignin, and synthetic sources, including conventional plastics. The review is structured in three main sections: catalytic depolymerization of cellulose, lignin, and plastics. Special emphasis is placed on recent studies that explore innovative methodologies. The raw materials obtained through these processes can be reintegrated into production cycles, contributing to the development of a fully circular economy. Full article

The current economic growth and increasing needs of society have led to developing processes that harm our environment and have severe long-term consequences. For this reason, different attempts have been made to mitigate these effects by substituting conventional toxic materials with environmentally friendly ones. Industry sectors related to energy storage, printed electronics, and wearable technology are moving towards applying sustainable strategies. Renewable biopolymers such as cellulose and its derivatives, as well as carbon-based alternatives, which include carbon nanotubes (CNTs), single-wall carbon nanotubes (SWCNTs), graphite, graphene, and carbon black (CB), are leading the advances in this field. The present research aimed to develop conductive cellulose paper using environmentally friendly components compatible with the paper recycling process. Coating formulations based on carbon black were proposed using three different types of binders: polytetrafluoroethylene (PTFE), latex (styrene butadiene), and sodium carboxymethyl cellulose (CMC). The formulation, composition, and preparation were studied, and they were related to the coating’s electrical resistance and integrity. This last parameter was determined through a new method described in this research, implementing a mechanical/optical technique to measure the coating’s durability. The formulation with the best performance in terms of electrical resistance (0.29 kΩ), integrity, and non-toxicity was obtained using sodium carboxymethyl cellulose (CMC) as a binder and dispersant. Full article

The nonwoven industry is undergoing significant changes, driven by rapid growth and sustainability concerns, with a growing need to shift from fossil-based polymers like polyester (PES) and polypropylene (PP) fibres to biodegradable, fossil-free materials. Compared to other cellulose-based fibres, lyocell (LY) is a promising solution due to its good mechanical performance and lower environmental impact. Additionally, cellulose acetate (CA) fibres, known for their thermoplastic and biodegradable properties, can act as a binder, offering another promising alternative to fossil-based fibres. This study explores the use of 100% LY fibres, alone and in blends with CA and recycled polyester (rPES) fibres, in the development of needle-punched nonwovens and assesses the mechanical benefits of adding a thermal bonding step. Among the blends, rPES-based nonwovens with thermal bonding showed the best results. 100% LY exhibited the best mechanical performance among needle-punched nonwovens, while rPES-based blends outperformed the others. Biodegradability and toxicity studies were also performed. 100% LY nonwovens fully biodegraded within 55 days, and 100% CA and 100% rPES showed no biodegradation. The findings revealed that the thermal process did not affect the disintegration level and, the germination of Brassica oleracea was not affected by soils in which the samples were buried for 75 days. Full article

Oil spills represent a significant environmental threat due to the toxicity of hydrocarbons, particularly in aquatic environments where oil rapidly spreads across the surface. Sustainable sorbents are needed for an efficient and eco-friendly response to oil spills. Cellulose aerogels produced from recycled paper and cardboard exhibit promising properties such as buoyancy, light weight, biocompatibility, and recyclability. Mechanical stability and reusability can be enhanced using cross-linkers such as starch. This study evaluated the impact of starch on cellulose aerogel morphology, sorption capacity for various petroleum products (crude oil, marine diesel, and lubricating oil), and reusability using scanning electron microscopy (SEM) and elemental mapping. Aerogels containing 0.5 and 1 wt% starch showed higher porosity, sorption capacity, and reusability. Starch did not affect hydrophobization or significantly alter nitrogen and carbon levels, indicating limited influence on surface chemistry and adsorption performance. Full article

Urban solid waste (USW) is a promising alternative source of valuable chemical compounds. It is considered an adsorbent material due to its chemical structure, porosity and electronic charge available to form chemical bonds and can be recovered or transformed for use in bioprocesses and industrial applications. This is the case with cigarette butts (CBs), which consist of thousands of substances that can be chemically converted for various purposes. This work showed high efficiency in the production of cellulose mass from the recycling of CBs, a patented technology in operation at the company Poiato Recicla—SP. The lignin-like solid (LLS)—a material obtained from the recycling of cigarette butts (CBs) by catalytic transfer hydrogenation (CTH), under non-rigorous conditions—showed high efficiency in its conversion into molecules of great interest. In the bio-oil obtained, characterized by analyses such as GCMS and RMN 2D HSQC, a mixture of predominantly hydrocarbons (many of them with cyclic and/or branched chains) was identified in almost all the experiments. This method demonstrates the potential of the TCH process for SSLs and completes the recycling chain designed for CBs, promoting their complete conversion into chemical compounds of greater interest. Full article

The enzyme ω-transaminase (ω-TA) has garnered significant attention due to its capacity to catalyze the synthesis of chiral amines with high efficiency. Nevertheless, the lack of stability of ω-TA and the difficulty of recycling and reuse are still challenges that limit its application. This study developed a novel magnetic nanocellulose composite carrier (NNC@Fe₃O₄@Ni), synthesized from microcrystalline cellulose via low-eutectic solvent treatment, amine modification, and metal hybridization. The NNC@Fe₃O₄@Ni was characterized by FTIR, XPS, XRD, BET, and VSM. Additionally, the performance and catalytic behavior of the immobilized enzyme were investigated. The results revealed that NNC@Fe₃O₄@Ni exhibited a high specific surface area, superparamagnetism, and dual-site functionality (amine/Ni²⁺). Response Surface Methodology (RSM) optimized the carrier-enzyme interaction parameters, yielding optimal immobilization conditions: a mass ratio of 50.8 mg g⁻¹, temperature of 12.5 °C, and duration of 58.6 min, achieving 82.91% enzyme activity recovery. Compared to free enzymes, the immobilized variant demonstrated enhanced catalytic stability, with expanded optimal pH (9.0) and temperature (30 °C). Thermal stability assessments showed 84.39% activity retention after 5 h at 30 °C and 90.30% residual activity post-120 h storage. The catalyst maintained >80% efficiency over 10 reuse cycles. These findings confirm the efficacy of magnetic nanocellulose carriers in enhancing ω-TA stability, reusability, and catalytic performance, offering a viable strategy for industrial biocatalytic processes. Full article

The textile industry is under increasing pressure to adopt sustainable practices due to the significant environmental impacts associated with fiber production, including high energy consumption, water usage, and substantial greenhouse gas emissions. The recycling of textile waste, particularly cotton, is a promising solution that has the potential to reduce landfill waste and decrease the demand for virgin fibers. However, mechanically recycled cotton fibers frequently demonstrate diminished mechanical properties compared to virgin fibers, which limits their potential for high-quality textile applications. This study explores the use of cross-linking agents (citric acid (CA) and sodium hypophosphite (SHP)), polymers (polyethylene glycol (PEG), chitosan (CH), carboxymethyl cellulose (CMC) and starch (ST)), and silicas (anionic (SA) and cationic (SC)) to enhance the mechanical properties of recycled cotton fibers. The treatments were then subjected to a hierarchical ranking, with the effectiveness of each treatment determined by its impact on enhancing fiber tenacity. The findings of this research indicate that the most effective treatment was starck (ST_50), which resulted in an enhancement of tenacity from 14.63 cN/tex to 15.34 cN/tex (+4.9%), closely followed by CA-SHP_110/110, which also reached 15.34 cN/tex (+4.6%). Other notable improvements were observed with CMC_50 (15.23 cN/tex), PEG_50 (14.91 cN/tex), and CA_50 (14.89 cN/tex), all in comparison to the control. In terms of yarn quality, the CA-SHP_110/110 treatment yielded the most substantial reductions in yarn irregularities, including thin places, thick places, and neps with decreases of 36%, 10%, and 7%, respectively. Furthermore, CA_50 exhibited moderate enhancements in yarn regularity, thin places (−12%), thick places (−6.1%), and neps (−8.9%). The results of this study demonstrate that combining CA with SHP, particularly when preceded by the heating of the solution before the addition of the fibers, results in a substantial enhancement of the structural integrity, strength, and overall quality of recycled cotton fibers. This approach offers a viable pathway for the improvement of the performance of recycled cotton, thereby facilitating its wider utilization in high-quality textile products. Full article