Search Results (846)

Pavement skid resistance is of vital importance for road safety. The objective of this study is to propose and validate a texture-based image indicator to predict pavement friction. This index enables pavement friction to be predicted easily and inexpensively using digital images, with predictions correlated to Dynamic Friction Tester (DFT) measurements. Three different types of asphalt surfaces (Dense-Grade Asphalt Concrete, Open-Grade Friction Course, and Chip Seal) were evaluated subject to various tire polishing cycles. Images were taken with corresponding friction coefficients obtained using DFT in the laboratory. The aggregate protrusion area is proposed as the indicator. Statistical models are established for each asphalt surface type to correlate the proposed indicator with friction coefficients. The results show that the adjusted R-squared values of all relationships are above 0.90. Compared to other image-based indicators in the literature, the proposed image indicator more accurately reflects the changes in pavement friction with the number of polishing cycles, proving its cost-effective use for considering pavement friction in the mix design stage. Full article

Defects in GIS can be effectively detected by detecting the partial discharge (PD). The common methods of detecting partial discharge are pulse current, ultrasonic and UHF (ultra-high frequency). However, the results of different methods may be different due to the different physical quantities detected. It is important to research the differences between the PD detection methods for the PD detection and analysis. In this study, we designed metal protrusion defects in GIS, including protrusion on the conductor and enclosure. Then, we detected the PD of defects using pulse current, UHF and ultrasonic methods at the same time. The PRPD patterns, maximum discharge amplitude of different defects and PD inception voltage (PDIV) detected by the three methods were analyzed. The PRPD patterns and discharge amplitude of the different methods were very similar to each other, but the PDIVs were different. It can be concluded that the process from the PD inception to breakdown can be divided into four sections based on the PRPD and the maximum discharge amplitude. The similarity between the three methods is because their signals are all related to the pulse current during the PD process, and differences in their PDIVs are caused by the differences in sensitivity. The sensitivity of the pulse current is the lowest among the three methods due to its poor anti-jamming capability. The sensitivity of UHF is higher, and that of ultrasonic is the highest. Full article

Cardiac tissue engineering is a promising strategy to restore cardiac function in heart failure patients. Understanding the cardiac tissue architecture including the cardiac stroma is essential for developing not only advanced cardiac tissue engineering but also novel therapeutic strategies. One of the crucial components of the cardiac stroma is the myocardial vasculature. To enhance the spatial visualization of the cardiac stromal cytoarchitecture with a particular focus on myocardial vasculature, we performed 3D reconstructions of the murine cardiac micro vessels using Serial Block-Face Scanning Electron Microscopy (SBF-SEM). These analyses revealed that pericyte cell bodies were primarily oriented lengthwise and extended several cellular protrusions towards the endothelium. At capillary branching points, some pericytes made contact with both capillaries emerging from branching. In addition to pericytes that are completely encapsulated by the common basal lamina together with capillary endothelial cells, we identified other vascular-associated cells located outside this sheath. Based on marker expression, these cells were distinguished from fibroblasts and suggested to be telocytes. The vascular-associated cells formed electron-dense contact zones with endothelial cells, suggesting functional coupling between these both cell types. In conclusion, this study provides detailed three-dimensional visualizations of the cardiac stroma with a particular focus on cardiac microvasculature, offering enhanced insight into the cardiac stromal cytoarchitecture. Full article

The market for non-concentrated (NFC) orange juice is increasing rapidly due to consumer demand for nutrients and flavor. However, it encounters challenges in microbial safety, particularly from Salmonella enterica and Listeria monocytogenes. This study aimed to exploit a bio-preservative for NFC orange juice. Results showed that the cyclic peptide cyclo-zp80r had good antibacterial activity, with minimum inhibitory concentration values of 2–8 μM against S. enterica and L. monocytogenes. It exhibited bactericidal action against S. enterica and bacteriostatic action against L. monocytogenes at a concentration of 128 μM. This study explored the effect of cyclo-zp80r on the pathogenicity of S. enterica and L. monocytogenes. The mortality rate of Galleria mellonella exposed to these pathogens in NFC orange juice decreased from 100% to 60% after cyclo-zp80r treatment, surpassing the effectiveness of nisin. Cyclo-zp80r exhibited depolarization effects on S. enterica and L. monocytogenes. It increased outer membrane permeability and damaged the membrane structure of S. enterica. Cyclo-zp80r also caused distinct morphological changes, mainly cell collapse in S. enterica and localized bubble-like protrusions in L. monocytogenes. It induced reactive oxygen species production and DNA binding. The species diversity and abundance in NFC orange juice were also reduced by cyclo-zp80r, particularly in the genera Pantoea, Aeromonas, Pseudomonas, and Erwinia. Additionally, cyclo-zp80r exhibited excellent stability at high temperature (121 °C, 5 min) and in fresh orange juice. These results suggest that cyclo-zp80r could be developed as an effective food bio-preservative. Full article

Background: Surface electromyography (sEMG) enables the non-invasive assessment of muscle activity and is widely used in orthodontics for evaluating masticatory muscles. However, little is known about the dynamic changes in facial expression muscles during orthodontic treatment. This study aimed to investigate alterations in facial muscle tone during the leveling and alignment phase in adult female patients undergoing fixed appliance therapy. Methods: The study included 30 female patients aged 20–31 years who underwent sEMG assessment at four time points: before treatment initiation (T0), at the start of appliance placement (T1), three months into treatment (T2), and six months into treatment (T3). Muscle activity was recorded during four standardized facial expressions: eye closure, nasal strain, broad smile, and lip protrusion. Electrodes were placed on the orbicularis oris, orbicularis oculi, zygomaticus major, and levator labii superioris alaeque nasi muscles. A total of 1440 measurements were analyzed using Friedman and Conover-Inman tests (α = 0.05). Results: Significant changes in muscle tone were observed during treatment. During lip protrusion, the orbicularis oris and zygomaticus major showed significant increases in peak and minimum activity (p < 0.01). Eye closure was associated with altered orbicularis oris activation bilaterally at T3 (p < 0.01). Nasal strain induced significant changes in zygomaticus and levator labii muscle tone, particularly on the right side (p < 0.05). No significant changes were noted during broad smiling. Conclusions: Orthodontic leveling and alignment influence the activity of selected facial expression muscles, demonstrating a dynamic neuromuscular adaptation during treatment. These findings highlight the importance of considering soft tissue responses in orthodontic biomechanics and suggest potential implications for facial esthetics and muscle function monitoring. Full article

In recent years, there has been a growing interest in the frictional anisotropy of snake scale-inspired surfaces, especially its potential applications in enhancing the bearing capacity of foundations (piles, anchor elements, and suction caissons) and reducing materials consumption and installation energy. This study first investigated the frictional properties and surface morphologies of the ventral scales of Cantor’s rat snakes (Ptyas dhumnades). Based on the findings on the snake scales, a novel snakeskin-inspired geosynthetic reinforcement (SIGR) is developed using 3D-printed polylactic acid (PLA). A series of pullout tests under different normal loads (25 kPa, 50 kPa, and 75 kPa) were performed to analyze the pullout behavior of SIGR in sandy soil. Soil deformation and shear band thickness were measured using Particle Image Velocimetry (PIV). The results revealed that the ventral scales of Ptyas dhumnades have distinct thorn-like micro-protrusions pointing towards the tail, which exhibit frictional anisotropy. A SIGR with a unilateral (one-sided) layout scales (each scale 1 mm in height and 12 mm in length) could increase the peak pullout force relative to a smooth-surface reinforcement by 29% to 67%. Moreover, the peak pullout force in the cranial direction (soil moving against the scales) was found to be 13% to 20% greater than that in the caudal direction (soil moving along the scales). The pullout resistance, cohesion, and friction angle of SIGR all showed significant anisotropy. The soil deformation around the SIGR during pullout was more pronounced than that observed with smooth-surface reinforcement, which suggests that SIGR can mobilize a larger volume of soil to resist external loads. This study demonstrates that SIGR is able to enhance the pullout resistance of reinforcements, thereby improving the stability of reinforced soil structures, reducing materials and energy consumption, and is important for the sustainability of geotechnical engineering. Full article

Aim: To evaluate whether maximum occlusal loading and periodontal status are different between teeth presenting deflective occlusal contacts and those without such contacts, specifically adjacent and homologous teeth. Method: A cross-sectional study was conducted using OccluSense to detect deflective contacts and quantify occlusal load per tooth. For group comparisons, the Kruskal–Wallis, Friedman, Cochran’s Q, and chi-squared tests were used. Results: A total of 493 teeth with deflective contacts were compared to 473 adjacent (first control group) and 457 homologous teeth (second control group). Teeth with deflective contacts showed significantly higher occlusal loading (mean value: 208) than adjacent (72) and homologous teeth (97) (p < 0.05). They also exhibited more advanced periodontal damage, including deeper probing depths, greater gingival recession, alveolar bone loss, and a wider periodontal ligament space. Deflective contacts in centric relation were more strongly linked to periodontal deterioration than those in protrusive or lateral mandibular movements, despite similar occlusal forces. Conclusions: Within this study’s limitations, deflective occlusal contacts are associated with increased occlusal forces and more severe periodontal damage, suggesting a biomechanical factor in periodontal disease progression. Full article

A superhydrophobic surface with hierarchical micro/nano-array structures was successfully fabricated on 6061 aluminum alloy through a combination of femtosecond laser etching and anodic oxidation. Femtosecond laser etching formed a regularly arranged microscale “pit-protrusion” array on the aluminum alloy surface. After modification with a fluorosilane ethanol solution, the surface exhibited superhydrophobicity with a contact angle of 154°. Subsequently, the anodic oxidation process formed an anodic oxide film dominated by an array of aluminum oxide (Al₂O₃) nanopores at the submicron scale. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses revealed that the nanopore structures uniformly and continuously covered the laser-ablated layer. This hierarchical structure significantly increased the surface water contact angle to 162°. Wettability analysis showed that the prepared composite coating formed an air layer accounting for 91% of the surface area. Compared with the sample only treated by femtosecond laser etching, the presence of the Al₂O₃ nanopore structure significantly enhanced the mechanical durability, superhydrophobic durability, and corrosion resistance of the superhydrophobic surface. The proposed multi-step fabrication strategy offers an innovative method for creating multifunctional, durable superhydrophobic coatings and has important implications for their large-scale industrial use. Full article

This study evaluates the effects of dietary lipid levels on growth performance, hematological health, and muscle composition of juvenile Arapaima gigas. We tested five isonitrogenous diets (451.7 g kg⁻¹ of crude protein) with increasing lipid levels (6%, 10%, 14%, 18%, and 22%). A total of 600 juvenile A. gigas (80.0 ± 10.5 g; 21.8 ± 1.0 cm) were distributed into 20 tanks (500 L; n = 4; 30 fish per tank) in an indoor open system. The fish were fed to apparent satiety four times daily for 60 days. As dietary lipid levels increased, all growth parameters and lipid content in both the whole body and muscle declined. The diet containing 6% lipids resulted in the maximum final weight, weight gain, feed intake, and the lowest feed conversion rate. However, a maximum lipid level of up to 10.26%, with a gross energy-to-protein ratio of 10.15 kcal g⁻¹ in the diet, as determined through polynomial regression analysis, can be used for juvenile A. gigas without significantly affecting weight gain. Diets with high lipid content (18% and 22% lipids) resulted in the lowest survival rates, highest feed conversion rates, lowest condition factor, visible skeletal protrusions, scale depigmentation, and impaired blood biochemistry. The content of eicosapentaenoic acid, docosahexaenoic acid, n-3, and the n-3:n-6 ratio increased in the muscle lipid fraction (mg g⁻¹ of total lipids) in response to higher dietary lipid levels; however, this does not represent an overall improvement in the meat quality, since the total lipid content in the muscle (g of lipid per 100 g of muscle) was reduced due to impaired growth in fish fed high-lipid diets. Notably, the experimental diets also differed in fatty acid composition, which may have influenced some of the physiological and compositional responses observed. Diets with 6% lipids are recommended to provide optimal growth performance, and a maximum dietary lipid level of up to 10.26% is advised to ensure successful A. gigas farming without impairing weight gain. Full article

This study investigated the effects of local fibroblast growth factor (FGF)-2 application on periodontal healing in an osteoporotic model, both in vivo and in vitro. Wistar rats were divided into the ovariectomy (OVX) and Control groups. Periodontal defects were created 8 weeks post-OVX and treated with hydroxypropylcellulose (HPC) or FGF-2 + HPC. Healing was evaluated through micro-computed tomography and histological analyses at 2 and 4 weeks. In vitro, bone marrow mesenchymal stromal cells (BMSCs) were cultured with/without FGF-2 and assessed for cell morphology, viability/proliferation, and osteoblastic marker expression. Alkaline phosphatase (ALP) staining was also performed. FGF-2-treated defects in both groups showed significantly greater bone volume fraction, trabecular number, and thickness compared to HPC only. Histologically, FGF-2 enhanced new bone formation, with the greatest levels in the Control group. In vitro, OVX BMSCs showed reduced actin staining versus controls. FGF-2 increased cell viability/proliferation and protrusions in both groups while downregulating Alpl and Bglap expression levels and reducing ALP-positive cells. FGF-2 increased new bone formation in the OVX group, stimulated proliferation of OVX BMSCs, and modulated their differentiation. FGF-2 could enhance periodontal healing even under osteoporotic conditions, albeit to a lesser extent. Full article

In this study, we investigated the electrochemical corrosion behavior and mechanisms of FeCrNi/WC alloys with varying contents of CTC-S (spherical WC) and CTC-A (angular WC) in a 3.5 wt.% NaCl solution, addressing the corrosion resistance requirements for stainless steel composites in marine environments. The electrochemical test results demonstrate that the corrosion resistance of the alloy initially increases with the CTC-A content, followed by a decrease, which is associated with the formation, stability, and rupture of the passivated film. Nyquist and Bode diagrams for electrochemical impedance spectroscopy confirm that the charge transfer resistance of the passivated film is the primary determinant of the composite’s corrosion performance. A modest increase in CTC-A contributes to the formation of a more heterogeneous second phase, providing a physical barrier and enhancing solid solution strengthening, and thus delaying the cracking and corrosion processes of the passivation film. However, excessive CTC-A content leads to significant dissolution of the alloy’s reinforcement phase and promotes decarburization, resulting in the formation of corrosion pits, craters, and cracks that compromise the passivation film and expose fresh alloy surfaces to further corrosion. When the CTC-A content is 10% and the CTC-S content is 30%, this combination results in minimal degradation in the corrosion performance (0.213 μA·cm²) while balancing the hardness and toughness of the alloy. Additionally, electrochemical evaluations reveal that incorporating angular CTC-A particles at 10 vol% effectively delays the breakdown of the passivation film by mitigating the interfacial galvanic coupling through enhancing the mechanical interlocking at the WC/FeCrNi interface. The CTC-A/CTC-S hybrid system exhibits a remarkable 62% reduction in the pitting propagation rate compared to composites reinforced solely with spherical WC, which is attributed to the preferential dissolution of angular WC protrusions that sacrificially suppress crack initiation at the phase boundaries. Full article

NF-Y transcriptional regulators play crucial roles in diverse biological processes in plants, primarily through the formation of NF-Y complexes that bind to specific DNA motifs. These complexes modulate the expression of downstream genes, which influence plant development and growth. In our research, the function of the NF-Y family C subunit member SlNF-YC9 gene in tomato was investigated with the CRISPR/Cas9 method. In contrast to the WT (wild type), the mutant CR-SlNF-YC9 exhibited a prominent protrusion at the fruit tip. The quantitative PCR analysis displayed that the transcription levels of genes associated with auxin transport (PIN4, PIN5, and PIN9) as well as auxin response genes (ARF7 and LAX3) were enhanced in the CR-SlNF-YC9 fruits than in the WT. Analysis of dual-luciferase reporter and EMSA assays showed that the SlNF-YC9-YB13b-YA7a trimer specifically binds the FUL2 promoter and represses its expression. In conclusion, our results suggest that SlNF-YC9 is crucial in influencing tomato fruit shape by the formation of NF-Y heterotrimeric complexes. Full article

This study aimed to evaluate the impact of Twin Block appliance therapy on skeletal, dentoalveolar, and facial soft tissue characteristics. The study included 18 participants with Class II skeletal malocclusion who were treated with the Twin Block appliance. Lateral cephalograms and 3D face scans were analyzed before and after therapy for each participant. Dependent t-test results showed a significant increase in the protrusion of the lower incisors (p < 0.001), proclination of the lower incisors (p = 0.021), SNB (p = 0.005), Ls:E (p = 0.040), mandibular length (p < 0.001), and soft tissue mandible length (p < 0.001) and a significant decrease in the ANB (p = 0.003), Wits (p = 0.001), ANPG (p = 0.001), overbite (p = 0.001), and the retrusion of upper incisors (p = 0.002). Twin Block therapy caused changes in skeletal and soft tissue characteristics. The increase in the SNB angle and mandibular length, accompanied by the decrease in the ANB and Wits values reduced the skeletal discrepancy. The reduction in the ANPG indicated an improvement in the skeletal profile. Additionally, the increase in the soft tissue mandible length and distance between the upper lip and E-line contributed to improved esthetic soft tissue profile characteristics. Full article

To address the challenges of cotton cellulose materials being susceptible to environmental humidity and pollutant erosion, a strategy for constructing superhydrophobic functional coatings with biomimetic micro–nano composite structures was proposed. Through surface silanization modification, diatomite (DEM) and Fe₃O₄ nanoparticles were functionalized with octyltriethoxysilane (OTS) to prepare superhydrophobic diatomite flakes (ODEM) and OFe₃O₄ nanoparticles. Following the multi-scale composite principle, ODEM and OFe₃O₄ nanoparticles were blended and crosslinked via the hydroxyl-initiated ring-opening polymerization of epoxy resin (EP), resulting in an EP/ODEM@OFe₃O₄ composite coating with hierarchical roughness. Microstructural characterization revealed that the micrometer-scale porous structure of ODEM and the nanoscale protrusions of OFe₃O₄ form a hierarchical micro–nano topography. The special topography combined with the low surface energy property leads to a contact angle of 158°. Additionally, the narrow bandgap semiconductor characteristic of OFe₃O₄ induces the localized surface plasmon resonance effect. This enables the coating to attain 80% light absorption across the 350–2500 nm spectrum, and rapidly heat to 45.8 °C within 60 s under 0.5 sun, thereby demonstrating excellent deicing performance. This work provides a theoretical foundation for developing environmentally tolerant superhydrophobic photothermal coatings, which exhibit significant application potential in the field of anti-icing and anti-fouling. Full article

High-Bandwidth Memory (HBM) enables the bandwidth required by modern AI and high-performance computing, yet its three dimensional stack traps heat and amplifies thermo mechanical stress. We first review how conventional solutions such as heat spreaders, microchannels, high density Through-Silicon Vias (TSVs), and Mass Reflow Molded Underfill (MR MUF) underfills lower but do not eliminate the internal thermal resistance that rises sharply beyond 12layer stacks. We then synthesize recent hybrid bonding studies, showing that an optimized Cu pad density, interface characteristic, and mechanical treatments can cut junction-to-junction thermal resistance by between 22.8% and 47%, raise vertical thermal conductivity by up to three times, and shrink the stack height by more than 15%. A meta-analysis identifies design thresholds such as at least 20% Cu coverage that balances heat flow, interfacial stress, and reliability. The review next traces the chain from Coefficient of Thermal Expansion (CTE) mismatch to Cu protrusion, delamination, and warpage and classifies mitigation strategies into (i) material selection including SiCN dielectrics, nano twinned Cu, and polymer composites, (ii) process technologies such as sub-200 °C plasma-activated bonding and Chemical Mechanical Polishing (CMP) anneal co-optimization, and (iii) the structural design, including staggered stack and filleted corners. Integrating these levers suppresses stress hotspots and extends fatigue life in more than 16layer stacks. Finally, we outline a research roadmap combining a multiscale simulation with high layer prototyping to co-optimize thermal, mechanical, and electrical metrics for next-generation 20-layer HBM. Full article