Search Results (4,318)

Compared with vanadium extraction by sodium roasting followed by water leaching, the calcification roasting–sulfuric acid leaching method is considered a promising approach for the comprehensive utilization of vanadium titanomagnetite, as it avoids the introduction of alkali metals. However, during vanadium extraction by sulfuric acid heap leaching, the diffusion of leaching reagents and leaching products was hindered by the deposition of leaching solid products. To address this issue, this study systematically investigated the leaching kinetics and the mechanisms underlying the deposition of leaching solid products. The results indicated that vanadium leaching was governed by a combination of liquid film diffusion and internal diffusion through solid-phase products during days 0–2, and by internal diffusion alone from day 2 to day 9. The primary solid products formed during leaching were calcium sulfate and silica gel. Calcium sulfate precipitated and grew within the pore via two-dimensional nucleation, while silicates formed silica gel through dehydration. By optimizing the sulfuric acid leaching conditions—specifically, maintaining an H⁺ concentration of 2 mol/L, a leaching temperature of 40 °C, and a liquid-to-solid ratio of 5:1—the formation of calcium sulfate and silica gel was effectively suppressed. Under these conditions, the vanadium leaching efficiency reached 75.82%. Full article

The high cost of hydrogen production is the primary factor limiting the development of the hydrogen energy industry chain. Additionally, due to the inefficiency of hydrogen production by water electrolysis technology, the development of high-performance catalysts is an effective means of producing low-cost hydrogen. In water electrolysis technology, the electrocatalytic activity of the electrode affects the kinetics of the oxygen evolution reaction (OER) and the hydrogen evolution rate. This study utilizes the liquid phase co-precipitation method to synthesize three types of Prussian blue analog (PBA) electrocatalytic materials: Fe/PBA(Fe₄[Fe(CN)₆]₃), Fe-Mn/PBA((Fe, Mn)₃[Fe(CN)₆]₂·nH₂O), and Fe-Mn-Co/PBA((Mn, Co, Fe)₃^II[Fe^III(CN)₆]₂·nH₂O). X-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses show that Fe-Mn-Co/PBA has a smaller particle size and higher crystallinity, and its grain boundary defects provide more active sites for electrochemical reactions. The electrochemical test shows that Fe-Mn-Co/PBA exhibits the best electrochemical performance. The overpotential of the oxygen evolution reaction (OER) under 1 M alkaline electrolyte at 10/50 mA·cm⁻² is 270/350 mV, with a Tafel slope of 48 mV·dec⁻¹, and stable electrocatalytic activity is maintained at 5 mA·cm⁻². All of these are attributed to the synergistic effect of Fe, Mn, and Co metal ions, grain refinement, and the generation of grain boundary defects and internal stresses. Full article

As a new type of alloy system composed of five or more principal components, high-entropy alloys demonstrate outstanding comprehensive performance in the field of friction and wear through the synergistic effects of the high-entropy effect, lattice distortion effect, hysteresis diffusion effect and cocktail effect. This paper systematically reviews the research progress on the friction and wear properties of high-entropy alloys. The mechanisms of metal elements such as Al, Ti, Cu and Nb through solid solution strengthening, second-phase precipitation and oxide film formation were analyzed emphatically. And non-metallic elements such as C, Si, and B form and strengthen the regulation laws of their tribological properties. The influence of working conditions, such as high temperature, ocean, and hydrogen peroxide on the friction and wear behavior of high-entropy alloys by altering the wear mechanism, was discussed. The influence of test conditions such as load, sliding velocity and friction pair matching on its friction coefficient and wear rate was expounded. It is pointed out that high-entropy alloys have significant application potential in key friction components, providing reference and guidance for the further development and application of high-entropy alloys. Full article

Climate change has accelerated the retreat of Andean glaciers, with significant recent losses in the tropical Andes. This study evaluates the extinction of the Carihuairazo volcano glacier (Ecuador), quantifying its area from 1312.5 m² in September 2023 to 101.2 m² in January 2024, its thickness (from 2.5 m to 0.71 m), and its volume (from 2638.85 m³ to 457.18 m³), before its complete deglaciation in February 2024; this rapid melting and its small size classify it as a glacierette. Multivariate analyses (PCA and biclustering) were performed to correlate climatic variables (temperature, solar radiation, precipitation, relative humidity, vapor pressure, and wind) with glacier surface and thickness. The PCA explained 70.26% of the total variance, with Axis 1 (28.01%) associated with extreme thermal conditions (temperatures up to 8.18 °C and radiation up to 16.14 kJ m⁻² day⁻¹), which probably drove its disappearance. Likewise, Axis 2 (21.56%) was related to favorable hydric conditions (precipitation between 39 and 94 mm) during the initial phase of glacier monitoring. Biclustering identified three groups of variables: Group 1 (temperature, solar radiation, and vapor pressure) contributed most to deglaciation; Group 2 (precipitation, humidity) apparently benefited initial stability; and Group 3 (wind) played a secondary role. These results, validated through in situ measurements, provide scientific evidence of the disappearance of the Carihuairazo volcano glacier by February 2024. They also corroborate earlier projections that anticipated its extinction by the middle of this decade. The early disappearance of this glacier highlights the vulnerability of small tropical Andean glaciers and underscores the urgent need for water security strategies focused on management, adaptation, and resilience. Full article

Environmental sustainability and responsible resource utilization are critical global challenges. In this work, we present a sustainable and circular-economy-based approach for synthesizing CuFe₂O₄ nanoparticles by directly utilizing copper oxide minerals sourced from Chilean mining operations. Copper sulfate (CuSO₄) was extracted from these minerals through acid leaching and used as a precursor for nanoparticle synthesis via both chemical co-precipitation and microwave-assisted methods. The influence of different precipitating agents—NaOH, Na₂CO₃, and NaF—was systematically evaluated. XRD and FESEM analyses revealed that NaOH produced the most phase-pure and well-dispersed nanoparticles, while NaF resulted in secondary phase formation. The microwave-assisted method further improved particle uniformity and reduced agglomeration due to rapid and homogeneous heating. Electrochemical characterization was conducted to assess the suitability of the synthesized CuFe₂O₄ for supercapacitor applications. Cyclic voltammetry (CV) and galvanostatic charge–discharge (GCD) measurements confirmed pseudocapacitive behavior, with a specific capacitance of up to 1000 F/g at 2 A/g. These findings highlight the potential of CuFe₂O₄ as a low-cost, high-performance electrode material for energy storage. This study underscores the feasibility of converting primary mined minerals into functional nanomaterials while promoting sustainable mineral valorization. The approach can be extended to other critical metals and mineral residues, including tailings, supporting the broader goals of a circular economy and environmental remediation. Full article

The prevailing environmental conditions before and during the 28 Large Forest Fires (LFFs) that have occurred in the Canary Islands since 1983 are analyzed. These conditions are often associated with episodes characterized by the advection of continental tropical air masses originating from the Sahara, which frequently result in intense heatwaves. During the onset of the LFFs, the base of the subsidence thermal inversion layer—separating a lower layer of cool, moist air from an upper layer of warm, dry air—is typically located at an altitude of around 350 m above sea level, approximately 600 m below the usual average. Understanding these Saharan air advection events is crucial, as they significantly alter the vertical thermal structure of the atmosphere and create highly conducive conditions for wildfire ignition and spread in the forested mid- and high-altitude zones of the archipelago. Analysis of meteorological records from various weather stations reveals that the average maximum temperature on the first day of fire ignition is 30.3 °C, with mean temperatures of 27.4 °C during the preceding week and 28.9 °C throughout the fire activity period. Relative humidity on the ignition days averages 24.3%, remaining at around 30% during the active phase of the fires. No significant correlation has been found between dry or wet years and the occurrence of LFFs, which have been recorded across years with widely varying precipitation levels. Full article

Based on molecular dynamics simulation, we conducted a comprehensive study on the tensile behaviors and properties of the $\gamma$(Ni)/${\gamma }^{\prime }$(Ni₃Al) superalloy with varying ${\gamma }^{\prime }$(Ni₃Al) phase volume fractions ($V\left({\gamma }^{\prime }\right))$ under high-temperature, high-strain-rate service environments. Our investigation revealed that the tensile behavior of the superalloy depends critically on the $V\left({\gamma }^{\prime }\right)$. When the $V\left({\gamma }^{\prime }\right)$ increased from 13.5 to 67%, the system’s tensile strength exhibited a non-monotonic response, peaking at $\mathrm{V}\left({\gamma }^{\prime }\right)$ = 40.3% before progressively decreasing. Conversely, the maximum uniform plastic strain decreased linearly and significantly when $V\left({\gamma }^{\prime }\right)$ increased. These results establish an atomistically informed framework that elucidates the composition–microstructure–property relationships in $\gamma$(Ni)/${\gamma }^{\prime }$(Ni₃Al) superalloys, specifically addressing how $V\left({\gamma }^{\prime }\right)$ governs variations in deformation mechanisms and mechanical performance. Furthermore, this work provides quantitative design paradigm for optimizing ${\gamma }^{\prime }$(Ni₃Al) precipitate architecture and compositional tuning in the Ni-based $\gamma$(Ni)/${\gamma }^{\prime }$(Ni₃Al) superalloy. Full article

Sanicro 25 (X7NiCrWCuCoNb25-23-3-3-2) steel is specifically designed for use in superheater components within the latest generation of conventional power plants. These power plants operate under conditions often referred to as super-ultra-supercritical, with steam parameters that can reach up to 30 MPa and temperatures of 653 °C for fresh steam and 672 °C for reheated steam. While last-generation supercritical power plants still rely on fossil fuels, they represent a significant step forward in more sustainable energy production. The most sophisticated facilities of this kind can achieve thermodynamic efficiencies exceeding 47%. This study aimed to conduct a detailed analysis of the initial precipitation processes occurring in Sanicro 25 steel within the temperature range of 700–900 °C. The temperature of 700 °C corresponds to the operational conditions of this material, particularly in secondary steam superheaters in thermal power plants that operate under ultra-supercritical parameters. Understanding precipitation processes is crucial for optimizing mechanical performance, particularly in terms of long-term strength and creep resistance. To accurately assess the microstructural changes that occur during the early stages of service, a digital twin approach was employed, which included CALPHAD simulations and experimental heat treatments. Experimental annealing tests were conducted in air within the temperature range of 700–900 °C. Precipitation behavior was simulated using the Thermo-Calc 2025a with Dictra software package. The results from Prisma simulations correlated well with the experimental data related to the kinetics of phase transformations; however, it was noted that the predicted sizes of the precipitates were generally smaller than those observed in experiments. Additionally, computational limitations were encountered during some simulations due to the complexity arising from the numerous alloying elements present in Sanicro 25 steel. The microstructural evolution was investigated using various methods, including light microscopy (LM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Full article

Theranostic materials, which combine therapeutic and diagnostic capabilities, represent a promising advancement in cancer treatment by improving both the precision and personalization of therapies. Recently, metal peroxides (MePOs) have attracted significant interest from researchers for their potential use in both cancer diagnosis and therapy. This review provides an overview of recent developments in the application of MePOs for innovative cancer treatment strategies. The unique properties of MePOs, such as oxygen generation, are highlighted for their potential to improve therapeutic outcomes, especially in hypoxic tumor microenvironments. Initially, methods for MePO synthesis are briefly discussed, including hydrolyzation–precipitation, reversed-phase microemulsion, and sonochemical techniques, emphasizing the role of surfactants in regulating the particle size and enhancing bioactivity. Next, we discuss the main therapeutic approaches where MePOs have shown promise. These applications include chemotherapy, photodynamic therapy (PDT), immunotherapy, and radiation therapy. Overall, we focus on integrating MePOs into theranostic platforms to enhance cancer treatment and enable diagnostic imaging for improved clinical outcomes. Finally, we discuss potential future research directions that could lead to clinical translation and the development of advanced medicines. Full article

This study examined the comprehensive properties of Mg-Zn-Nd-Zr alloys in order to achieve both high strength and thermal conductivity simultaneously. The impact of rolling on the microstructure, mechanical properties, and thermal conductivity was analyzed for Mg-5Zn-xNd-0.4Zr alloys (x = 1, 2). The results indicate that the addition of Nd promotes the formation of the W phase (Mg₃Zn₃RE₂), which contributes to grain boundary strengthening and enhances the overall strength. Moreover, dynamic precipitation during the rolling process leads to the formation of nanoscale MgZn₂ and Zn₂Zr phases, significantly improving both the strength and thermal conductivity. After rolling, both the Mg-5Zn-1Nd-0.4Zr (ZNK510) and Mg-5Zn-2Nd-0.4Zr (ZNK520) alloys exhibited a notable enhancement in thermal conductivity, with ZNK520 demonstrating superior properties due to its higher Nd content. This study highlights that optimizing alloy composition and phase evolution through rolling can markedly enhance both the mechanical and thermal properties, offering a promising strategy for the development of high-performance magnesium alloys. Full article

Background/Objectives: Magnetic nanoparticles, particularly iron oxide-based materials, such as magnetite (Fe₃O₄), have gained significant attention as contrast agents in medical imaging This study aimsto syntheze and characterize Fe₃O₄-based core–shell nanostructures, including Fe₃O₄@TiO₂ and Fe₃O₄@SiO₂, and to evaluate their potential as tunable contrast agents for diagnostic imaging. Methods: Fe₃O₄, Fe₃O₄@TiO₂, and Fe₃O₄@SiO₂ nanoparticles were synthesized via co-precipitation at varying temperatures from iron salt precursors. Fourier transform infrared spectroscopy (FTIR) was used to confirm the presence of Fe–O bonds, while X-ray diffraction (XRD) was employed to determine the crystalline phases and estimate average crystallite sizes. Morphological analysis and particle size distribution were assessed by scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX) and transmission electron microscopy (TEM). Magnetic properties were investigated using vibrating sample magnetometry (VSM). Results: FTIR spectra exhibited characteristic Fe–O vibrations at 543 cm⁻¹ and 555 cm⁻¹, indicating the formation of magnetite. XRD patterns confirmed a dominant cubic magnetite phase, with the presence of rutile TiO₂ and stishovite SiO₂ in the coated samples. The average crystallite sizes ranged from 24 to 95 nm. SEM and TEM analyses revealed particle sizes between 5 and 150 nm with well-defined core–shell morphologies. VSM measurements showed saturation magnetization (Ms) values ranging from 40 to 70 emu/g, depending on the synthesis temperature and shell composition. The highest Ms value was obtained for uncoated Fe₃O₄ synthesized at 94 °C. Conclusions: The synthesized Fe₃O₄-based core–shell nanomaterials exhibit desirable structural, morphological, and magnetic properties for use as contrast agents. Their tunable magnetic response and nanoscale dimensions make them promising candidates for advanced diagnostic imaging applications. Full article

In this work, the W element, with a larger atomic radius compared to Co, Fe, and Ni, was added to modify the microstructure and enhance the yield strength of CoFeNi medium entropy alloy (MEA). A detailed study was conducted to clarify the effects of W additions and annealing temperatures on the microstructure evolution and mechanical properties of CoFeNiW_x (x = 0, 0.1, and 0.3) MEAs. CoFeNiW_0.1 retained a single FCC structure without the formation of precipitates in the FCC phase, indicating that W, with a larger atomic radius, can completely dissolve in CoFeNiW_0.1. For CoFeNiW_0.3 MEA, coarse particles with an average diameter of ~2 μm appeared after homogenizing. Nevertheless, when the alloy was annealed at 800 °C and 900 °C, fine particles formed, with the average diameters of approximately 144 nm and 225 nm, respectively. After annealing at 800 °C, the CoFeNiW_0.3 with a partially recrystallized microstructure exhibited better comprehensive mechanical properties. Full article

For effective groundwater resource management, it is essential to model the dynamic behaviour of aquifers in response to rainfall. Here, a methodological approach using a recurrent neural network, specifically a Long Short-Term Memory (LSTM) network, is used to model groundwater levels of the shallow porous aquifer in Southern Italy. This aquifer is recharged by local rainfall, which exhibits minimal variation across the catchment in terms of volume and temporal distribution. To gain a deeper understanding of the complex interactions between precipitation and groundwater levels within the aquifer, we used water level data from six wells. Although these wells were not directly correlated in terms of individual measurements, they were geographically located within the same shallow aquifer and exhibited a similar hydrogeological response. The trained model uses two variables, rainfall and groundwater levels, which are usually easily available. This approach allowed the model, during the training phase, to capture the general relationships and common dynamics present across the different time series of wells. This methodology was employed despite the geographical distinctions between the wells within the aquifer and the variable duration of their observed time series (ranging from 27 to 45 years). The results obtained were significant: the global model, trained with the simultaneous integration of data from all six wells, not only led to superior performance metrics but also highlighted its remarkable generalization capability in representing the hydrogeological system. Full article

In the search for alternative protein sources, single cell proteins have gained increasing attention in recent years. Among them, proteins derived from yeast represent a promising but still underexplored option. To enable their application in food product design, their techno-functional properties must be understood. In order to investigate the impact of precipitation pH on their emulsion-stabilizing properties, yeast proteins from Saccharomyces cerevisiae were isolated via precipitation at different pH (pH 3.5 to 5) after cell disruption in the high-pressure homogenizer. Emulsions containing 5 wt% oil and ~1 wt% protein were analyzed for stability based on their droplet size distribution. Proteins precipitated at pH 3.5 stabilized the smallest oil droplets and prevented partitioning of the emulsion, outperforming proteins precipitated at higher pH values. It is hypothesized that precipitation under acidic conditions induces protein denaturation and thereby exposes hydrophobic regions that enhance adsorption at the oil–water interface and the stabilization of the dispersed oil phase. To investigate the stabilization mechanism, the molecular weight of the proteins was determined using SDS-PAGE, their solubility using Bradford assay, and their aggregation behavior using static laser scattering. Proteins precipitated at pH 3.5 possessed larger molecular weights, lower solubility, and a strong tendency to aggregate. Overall, the findings highlight the potential of yeast-derived proteins as bio-surfactants and suggest that pH-controlled precipitation can tailor their functionality in food formulations. Full article

In order to obtain the optimal heat treatment process of Er-containing 7075 aluminum alloy, the effects of pre-stretching and the interval time between pre-stretching and aging on the microstructure and mechanical properties of Er-containing 7075 aluminum alloy during solution treatment followed by pre-stretching and two-stage aging processes were investigated by mechanical property tests, metallographic tests, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results show that the mechanical properties of Er-containing 7075 aluminum alloy can be significantly improved by increasing the extrusion ratio. Pre-stretching provides nucleation sites for the precipitation of reinforcing phases, accelerates the aging strengthening process, and shortens the peak aging time. The crack source of fracture in Er-containing 7075 aluminum alloy is attributed to the segregated second phases containing Cu and Er in the alloy. The research results have significant engineering significance for the optimization of the heat treatment process of Er-containing 7075 aluminum alloy. Full article