Search Results (86)

Gallium oxide (Ga₂O₃), as an ultra-wide bandgap semiconducting material, has attracted extensive research interest in recent years. Owing to its outstanding electrical and optical properties, as well as its high reliability, Ga₂O₃ shows great potential in power electronics, optoelectronics, memory devices, and so on. Among all the different polymorphs, ε-Ga₂O₃ is the second most thermally stable phase. It has a hexagonal crystal structure, which contributes to its isotropic physical properties and its suitable growth on low-cost commercial substrates, such as Al₂O₃, Si (111). However, there are far fewer research works on ε-Ga₂O₃ in comparison with the most thermally stable β phase. Aiming to provide a comprehensive view on the current works of ε-Ga₂O₃ and support future research, this review conducts detailed summarizations for the fabrication processes of ε-Ga₂O₃ thin films and the photoelectrical properties of ε-Ga₂O₃-based photodetectors. The effects of different deposition parameters on film phases and qualities are discussed. The forming mechanisms of ε phase prepared by chemical vapor depositions (CVDs) and physical vapor depositions (PVDs) are analyzed, respectively. Conclusions are made concerning the relationships between film microstructures and properties. In addition, strategies for further improving ε-Ga₂O₃ film performance are briefly summarized. Full article

The synthesis and characterization of MgO-ZrO₂ heterostructures are examined in this work. To promote the creation of nanowires, the Si substrate is first covered with a catalyst layer of various Au thicknesses. Sputtering is used to achieve this deposition. After that, chemical vapor deposition (CVD) with a Au catalyst layer is used to create MgO nanowire arrays on the silicon substrate. Second, MgO/ZrO₂ Core–shell Nanowire Arrays are created by applying ZrO₂ layers to the surface of MgO nanowires of different diameters using chemical vapor deposition (CVD) procedures. The presence of both magnesium oxide (MgO) and zirconium dioxide (ZrO₂) in their oxidized forms was shown by the detailed characterization of the MgO-ZrO₂ core–shell nanowire samples utilizing a variety of methods. Phase formation, mechanical homogeneity, optical characteristics, and topographical structure and roughness were all thoroughly examined at various stresses. MgO hardness values ranged from 1.4 to 3.2 GPa, whereas MgO-ZrO₂ ranged from 0.38 to 1.2 GPa. The I–V parameter study was a further step in the examination of the heterostructure’s electrical properties. The structural, morphological, optical, mechanical, and electrical properties of the MgO-ZrO₂ heterostructure were all thoroughly described using these techniques. Full article

Chemical vapor deposition (CVD) is a highly adaptable manufacturing technique used to fabricate high-quality thin films, making it essential across numerous industries. As materials fabrication processes progress, CVD has advanced to enable the precise deposition of both inorganic 2D materials, such as graphene and transition metal dichalcogenides, and high-quality polymeric thin films, offering excellent conformality and precise nanostructure control on a wide range of substrates. Conjugated conducting polymers have emerged as promising materials for next-generation electronic, optoelectronic, and energy storage devices due to their unique combination of electrical conductivity, optical transparency, ionic transport, and mechanical flexibility. Oxidative CVD (oCVD) involves the spontaneous reaction of oxidant and monomer vapors upon their adsorption onto the substrate surface, resulting in step-growth polymerization that commonly produces conducting or semiconducting polymer thin films. oCVD has gained significant attention for its ability to fabricate conjugated conducting polymers under vacuum conditions, allowing precise control over film thickness, doping levels, and nanostructure engineering. The low to moderate deposition temperature in the oCVD method enables the direct integration of conducting and semiconducting polymer thin films onto thermally sensitive substrates, including plants, paper, textiles, membranes, carbon fibers, and graphene. This review explores the fundamentals of the CVD process and vacuum-based manufacturing, while also highlighting recent advancements in the oCVD method for the fabrication of conjugated conducting and semiconducting polymer thin films. Full article

To improve the friction performance and service life of protective coatings in humidity-fluctuating environments, porous hard titanium nitride (TiN)–molybdenum disulfide (MoS₂) composite coatings were prepared by using direct current magnetron sputtering (DCMS) with the mode of oblique angle deposition (OAD) and chemical vapor deposition (CVD) technologies. The structure and chemical component were characterized by field emission scanning electron microscopy (FESEM), energy dispersive spectrometer (EDS), grazing incidence X-ray diffraction (GIXRD), atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy. The tribological properties of these TiN–MoS₂ composite coatings were investigated. The results indicate that the porous TiN–MoS₂ composite coating exhibited outstanding friction performance and long service life under humidity-fluctuating environments. At the initial 20% relative humidity (RH) stage, the MoS₂ on the porous TiN–MoS₂ composite coating surface worked as an effective lubricant; thus, the coating demonstrated excellent lubrication performance, and the friction coefficient (COF) was about 0.05. As the humidity was alternated to 70% RH, the lubrication effect diminished due to the production of molybdenum oxide (MoO₃), and the COF was about 0.2, which was attributed to the degradation of MoS₂ on the wear track and the release of fresh MoS₂ from the porous TiN matrix. After the environmental conditions shifted from 70% to 20% RH, the MoO₃ was removed, and the lubrication effect was restored. In summary, TiN–MoS₂ porous composite coating offers a promising approach for lubrication in humidity-fluctuating environments. Full article

Single-atom catalysts (SACs) are presently recognized as cutting-edge heterogeneous catalysts for electrochemical applications because of their nearly 100% utilization of active metal atoms and having well-defined active sites. In this regard, SACs are considered renowned electrocatalysts for electrocatalytic O₂ reduction reaction (ORR), O₂ evolution reaction (OER), H₂ evolution reaction (HER), water splitting, CO₂ reduction reaction (CO₂RR), N₂ reduction reaction (NRR), and NO₃ reduction reaction (NO₃RR). Extensive research has been carried out to strategically design and produce affordable, efficient, and durable SACs for electrocatalysis. Meanwhile, persistent efforts have been conducted to acquire insights into the structural and electronic properties of SACs when stabilized on an adequate matrix for electrocatalytic reactions. We present a thorough and evaluative review that begins with a comprehensive analysis of the various substrates, such as carbon substrate, metal oxide substrate, alloy-based substrate, transition metal dichalcogenides (TMD)-based substrate, MXenes substrate, and MOF substrate, along with their metal-support interaction (MSI), stabilization, and coordination environment (CE), highlighting the notable contribution of support, which influences their electrocatalytic performance. We discuss a variety of synthetic methods, including bottom-up strategies like impregnation, pyrolysis, ion exchange, atomic layer deposition (ALD), and electrochemical deposition, as well as top-down strategies like host-guest, atom trapping, ball milling, chemical vapor deposition (CVD), and abrasion. We also discuss how diverse regulatory strategies, including morphology and vacancy engineering, heteroatom doping, facet engineering, and crystallinity management, affect various electrocatalytic reactions in these supports. Lastly, the pivotal obstacles and opportunities in using SACs for electrocatalytic processes, along with fundamental principles for developing fascinating SACs with outstanding reactivity, selectivity, and stability, have been highlighted. Full article

In this work, the simple fabrication of a new superhydrophobic magnetic sponge based on CNTs, NiFe₂O₄ nanoparticles, and PDMS was investigated. CNTs were synthesized by chemical vapor deposition (CVD) on a nickel ferrite catalyst supported on aluminum oxide (NiFe₂O₄/Al₂O₃). The synthesis of nickel ferrite (NiFe) was accomplished using the sol–gel method, yielding magnetic nanoparticles (43 Am²kg⁻¹, coercivity of 93 Oe, 21–29 nm). A new superhydrophobic magnetic PU/CNT/NiFe₂O₄/PDMS sponge was fabricated using a polyurethane (PU) sponge, CNTs, NiFe₂O₄ nanoparticles, and polydimethylsiloxane (PDMS) through the immersion coating method. The new PU/CNT/NiFe₂O₄/PDMS sponge exhibits excellent superhydrophobic/oleophilic/mechanical properties and water repellency (water absorption rate of 0.4%) while having good absorption of oil, olive oil, and organic liquids of different densities (absorption capacity of 21.38 to 44.83 g/g), excellent separation efficiency (up to 99.81%), the ability to be reused for removing oil and organic solvents for more than 10 cycles, and easy control and separation from water using a magnet. The new PU/CNT/NiFe₂O₄/PDMS sponge is a promising candidate as a reusable sorbent for collecting oil and organic pollutants and can also be used as a hydrophobic filter due to its excellent mechanical properties. Full article

Fabrication aspects of PdO thin films and coatings are reviewed here. The work provides and organizes the up-to-date information on the methods to obtain the films. In recent years, the interest in Pd oxide for different applications has increased. Since Pd can be converted into PdO, it is instructive to pay attention to the preparation of the pure and the alloyed Pd films, heterostructures, and nanoparticles synthesized on different substrates. The development of PdO films is presented from the early reports on coatings’ formation by oxidation of Pd foils and wires to present technologies. Modern synthesis/growth routes are gathered into chemical and physical categories. Chemical methods include hydrothermal, electrochemical, electroless deposition, and coating methods, such as impregnation, precipitation, screen printing, ink jet printing, spin or dip coating, chemical vapor deposition (CVD), and atomic layer deposition (ALD), while the physical ones include sputtering and cathodic arc deposition, laser ablation, ion or electron beam-induced deposition, evaporation, and supersonic cluster beam deposition. Analysis of publications indicates that many as-deposited Pd or Pd-oxide films are granular, with a high variety of morphologies and properties targeting very different applications, and they are grown on different substrates. We note that a comparative assessment of the challenges and quality among different films for a specific application is generally missing and, in some cases, it is difficult to make a distinction between a film and a randomly oriented, powder-like (granular), thin compact material. Textured or epitaxial films of Pd or PdO are rare and, if orientation is observed, in most cases, it is obtained accidentally. Some practical details and challenges of Pd oxidation toward PdO and some specific issues concerning application of films are also presented. Full article

The present study focused on demonstrating the versatility of the slurry deposition technique to produce aluminide coatings to protect components from high-temperature corrosion in a broad temperature range, from 400 to 1400 °C. This is a simpler and low-cost coating technology used as an alternative to CVD and pack cementation, which also allows the coating of complex geometries and offers improved and simple repairability for a lot of industrial applications, along with avoiding the use of non-hazardous components. Slurry aluminide coatings from a proprietary water-based-Cr6+ free slurry were produced onto four different substrates: A516 carbon steel, 310H AC austenitic steel, Ti6246 Ti-based alloy and TZM, a Mo-based alloy. The resulting coatings were thoroughly characterised by FESEM and XRD, mainly so that the identification of microstructures and appropriate phases was reported for each coating. The importance of surface preparation and heat treatment as key parameters for the coating final microstructures was also evidenced, and how those parameters can be optimised to obtain stable intermetallic phases rich in Al to sustain the formation of a protective Al₂O₃ oxide scale. These coating systems have applications in diverse industrial environments in which high-temperature corrosion limits the lifetime of the components. Full article

Beta-phase gallium oxide (β-Ga₂O₃) is a cutting-edge ultrawide bandgap (UWBG) semiconductor, featuring a bandgap energy of around 4.8 eV and a highly critical electric field strength of about 8 MV/cm. These properties make it highly suitable for next-generation power electronics and deep ultraviolet optoelectronics. Key advantages of β-Ga₂O₃ include the availability of large-size single-crystal bulk native substrates produced from melt and the precise control of n-type doping during both bulk growth and thin-film epitaxy. A comprehensive understanding of the fundamental growth processes, control parameters, and underlying mechanisms is essential to enable scalable manufacturing of high-performance epitaxial structures. This review highlights recent advancements in the epitaxial growth of β-Ga₂O₃ through various techniques, including Molecular Beam Epitaxy (MBE), Metal-Organic Chemical Vapor Deposition (MOCVD), Hydride Vapor Phase Epitaxy (HVPE), Mist Chemical Vapor Deposition (Mist CVD), Pulsed Laser Deposition (PLD), and Low-Pressure Chemical Vapor Deposition (LPCVD). This review concentrates on the progress of Ga₂O₃ growth in achieving high growth rates, low defect densities, excellent crystalline quality, and high carrier mobilities through different approaches. It aims to advance the development of device-grade epitaxial Ga₂O₃ thin films and serves as a crucial resource for researchers and engineers focused on UWBG semiconductors and the future of power electronics. Full article

Bismuth-based compounds have been regarded as a kind of promising material due to their narrow bandgap, high carrier mobility, low toxicity, and strong oxidation ability, showing potential applications in the field of photoelectrochemical (PEC) activities. They can be applied in sustainable energy production, seawater desalination and treatment, optical detection and communication, and other fields. As a member of the broader family of bismuth-based materials, β-Bi₂O₃ exhibits significant advantages for applications in engineering, including high photoelectric response, stability in harsh environments, and excellent corrosion resistance. This paper presents the synthesis of β-Bi₂O₃ thin films utilizing the mist chemical vapor deposition (CVD) method at the optimal temperature of 400 °C. Based on the β-Bi₂O₃ thin film synthesized at optimal temperature, a PEC-type photodetector was constructed with the highest responsivity R of 2.84 mA/W and detectivity D of 6.01 × 10¹⁰ Jones, respectively. The photodetection performance was investigated from various points like illumination light wavelength, power density, and long-term stability. This study would broaden the horizontal and practical applications of β-Bi₂O₃. Full article

To curtail the negative effects of traditional flood machining, dry cutting using carbide tools has emerged as a prominent alternative for manufacturers, owing to its low cost and phenomenal surface qualities. In line with this view, high-speed machining of high-strength AISI 4340 alloy steel was carried out using multilayer Al₂O₃/TiCN-CVD and TiAlN/AlCrN-PVD carbide tools in a dry environment. The experimental scheme was adopted, as per Taguchi’s L₁₈ orthogonal array, to investigate the two most crucial machinability aspects, namely tool life and surface roughness. An analysis of variance (ANOVA) was performed on the obtained data, and it was inferred that the feed rate exhibited the strongest effects on both the tool life and surface roughness, with corresponding percentage contributions of 46.22% and 68.96%, respectively. The longest tool lives of 14.75 min and 10.08 min were obtained at a low cutting speed and feed rate for CVD and PVD tools, respectively. However, the lowest surface roughness of 0.276 µm and 0.307 µm was achieved at a high cutting speed and low feed rate for PVD and CVD tools, respectively. The evolution of tool wear, studied through the microscopic images of the worn tools, revealed that a high cutting speed and feed rate accelerated the flank wear for both types of tools. Nevertheless, the CVD tool exhibited better results due to the thick and effective Al₂O₃/TiCN coating layer, which protected the carbide substrate against thermal–mechanical loads. Moreover, scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX) performed on the worn tools revealed that adhesion, oxidation, diffusion, and abrasion were the main wear mechanisms for both types of tools. Full article

A new type of catalyst containing magnesium oxide modified with various modifiers ranging from bromine and iodine, to interhalogen compounds, hydrohalogenic acids, and alkyl halides have been prepared using chemical vapor deposition (CVD) and wet impregnation methods. The obtained systems were characterized using a number of methods: determination of the concentration of X⁻ ions, surface area determination, powder X-ray diffraction (PXRD), surface acid–base strength measurements, TPD of probe molecules (acetonitrile, pivalonitrile, triethylamine, and n-butylamine), TPD-MS of reaction products of methyl iodide with MgO, and Fourier transform infrared spectroscopy (FTIR). The catalysts’ activity and chemoselectivity during transfer hydrogenation from ethanol to acrolein to allyl alcohol was measured. A significant increase in the activity of modified MgO (up to 80% conversion) in the transfer hydrogenation of acrolein was found, while maintaining high chemoselectivity (>90%) to allyl alcohol. As a general conclusion, it was shown that the modification of MgO results in the suppression of strong basic sites of the oxide, with a simultaneous appearance of Brønsted acidic sites on its surface. Independently, extensive research on the reaction progress of thirty alkyl halides with MgO was also performed in order to determine its ability to neutralize chlorinated wastes. Full article

This work aims to explore a method of improving the high-temperature oxidation resistance and thermal corrosion resistance of a hollow blade of gas turbine. The yttrium-modified aluminide coating was prepared on the surface of nickel-based superalloy K444 by chemical vapor deposition (CVD). The microstructure, high temperature oxidation resistance, and thermal corrosion resistance of the modified aluminide coating deposited at 950 °C, 1000 °C, and 1050 °C were compared. The microstructure and morphology of the coatings were observed and analyzed by XRD, SEM, and EDS. The results showed that adding yttrium and changing the deposition temperature had no effect on the double-layer structure (outer layer and diffusion layer) of the coating. Compared with adding yttrium, the deposition temperature had a greater effect on the coating thickness. When the deposition temperature was 1050 °C and the deposition time was 2 h, the thickness of the yttrium-modified aluminide coating increased by 33% compared to that of a single aluminide coating. The high temperature oxidation resistance and thermal corrosion resistance of the three groups of yttrium-modified aluminide coatings are better than that of the single aluminide coating. The resistance to high temperature oxidation and hot corrosion of the yttrium-modified aluminide coating deposited at 1050 °C was better than that of yttrium-modified aluminide coating deposited at 1000 °C, and both were better than that of the modified coating deposited at 950 °C. The higher the deposition temperature, the higher the yttrium content of the coating, the faster the film-forming speed of α-Al₂O₃, and the better the high temperature oxidation resistance and thermal corrosion resistance of the coating. Full article

Bromate, often detected in drinking water, is associated with a significant risk of cancer. Catalytic reduction has been recognized as an effective treatment technique to remove ions by reducing them over metal catalysts in the presence of a reducing agent, usually hydrogen. This work aims to synthesize metallic magnetic nanoparticles of iron oxide (FeO) and mixed iron oxides with manganese (MnFeO), cobalt (CoFeO), and copper (CuFeO) coated with carbon via chemical vapor deposition (C-MNP) to be applied as catalysts to the reduction of bromate in water. The use of magnetic nanoparticles coated with carbon enables catalyst recovery via magnetic separation and takes advantage of the catalytic properties of the carbon materials. The iron particles proved to be the most promising catalysts for the reduction of bromate into bromide, the highest removal being obtained with the CFeO@CVD750 sample, resulting in a 99% conversion after 120 min of reaction under the conditions tested. Due to its magnetic nature, the catalytic material was easily removed after the reaction and applied in four consecutive cycles without losing its catalytic properties. These results highlight the great potential of carbon-coated magnetic nanoparticles for reducing bromate in water. Full article

Myeloperoxidase (MPO) is a heme-containing peroxidase, mainly expressed in neutrophils and, to a lesser extent, in monocytes. MPO is known to have a broad bactericidal ability via catalyzing the reaction of Cl⁻ with H₂O₂ to produce a strong oxidant, hypochlorous acid (HOCl). However, the overproduction of MPO-derived oxidants has drawn attention to its detrimental role, especially in diseases characterized by acute or chronic inflammation. Broadly speaking, MPO and its derived oxidants are involved in the pathological processes of diseases mainly through the oxidation of biomolecules, which promotes inflammation and oxidative stress. Meanwhile, some researchers found that MPO deficiency or using MPO inhibitors could attenuate inflammation and tissue injuries. Taken together, MPO might be a promising target for both prognostic and therapeutic interventions. Therefore, understanding the role of MPO in the progress of various diseases is of great value. This review provides a comprehensive analysis of the diverse roles of MPO in the progression of several diseases, including cardiovascular diseases (CVDs), neurodegenerative diseases, cancers, renal diseases, and lung diseases (including COVID-19). This information serves as a valuable reference for subsequent mechanistic research and drug development. Full article