Search Results (282)

Oil and gas field water not only contains low concentrations of lithium but also a lot of suspended matter, inorganic salt, and organic matter. Both inorganic ions and organic substances influence the extraction of lithium. To improve the extraction efficiency of low-concentration lithium in oil and gas field water, the effects of Na⁺, K⁺, Ca²⁺, Mg²⁺, Cl⁻, Br⁻, SO₄²⁻, NO₃⁻, and organic substances on the extraction efficiency of lithium were studied. The results showed that Na⁺ can promote the extraction of lithium to a certain extent, and lithium ions competed with K+ for extraction; however, the separation coefficient remained more than 13. Ca²⁺ and Mg²⁺ have a significant influence on the extraction of lithium and should be removed prior to extraction. Cl⁻, SO₄²⁻, and NO₃⁻ have little influence on the extraction solution of lithium. Among the organic components, a high concentration of long-chain alkane has a certain effect on the extraction efficiency of lithium, while other substances have little effect. On this basis, the first step for precipitating impurity ions and the second step for solvent extraction of lithium were established. After removing the impurity ions, the extraction efficiency of lithium can reach over 90%. Taking 15L of oil and gas field water as the research object, after extraction, back extraction, concentration, depth impurities removal by extraction, and precipitation drying, the purity of the lithium carbonate product can be achieved at 99.28%. This study can provide technical support for the efficient extraction of low-concentration lithium from oil and gas field water. Full article

Agriculture and animal feeding operations are responsible for 87% of ammonia emissions in the UK. Controlling NH₃ concentrations below 20 ppm is crucial to preserve workers’ and livestock’s well-being. Therefore, ammonia control systems are required for maintaining adequate air quality in livestock facilities. This study assessed the ammonia reduction efficiency of a novel air pollution abatement (APA) system used in a pig farm building. The monitoring duration was 11 weeks. The results were compared with the baseline from a previous pig cycle during the same time of year in 2023. A ventilation-controlled room was monitored during a two-phase campaign, and the actual ammonia concentrations were measured at different locations within the site and at the inlet/outlet of the APA system. A 98% ammonia reduction was achieved at the APA outlet through NH₃ absorption in tap water. Ion chromatography analyses of farm water samples revealed NH₃ concentrations of up to 530 ppm within 83 days of APA operation. Further scanning electron microscopy and energy-dispersive X-ray inspections revealed the presence of salts and organic/inorganic matter in the solid residues. This research can contribute to meeting current ammonia regulations (NECRs), also by reusing the process water as a potential nitrogen fertiliser in agriculture. Full article

We present a brief overview of the field of charge density waves (CDW) in condensed systems with focus set to the underlying mechanisms behind the CDW ground state. Our intention in this short review is not to count all related facts from the vast volume of literature about this decades-old and still developing field, but rather to pinpoint the most important, mostly theoretical ones, presenting the development of the field. Starting from the “early days”, mainly based on weakly coupled, chain-like quasi-1D systems and Peierls instability, in which the Fermi surface nesting has been the predominant and practically paradigmatic mechanism of the CDW ground state stabilisation, we track the change in paradigms while entering the field of layered quasi-2D systems, with Fermi surface far away from the nesting regime, in which rather strong, essentially momentum-dependent interactions and particular reconstructions of the Fermi surface become essential. Examples of real quasi-1D materials, such as organic and inorganic conductors like Bechgaard salts or transition metal trichalcogenides and bronzes, in which experiment and theory have been extremely successful in providing detailed understanding, are contrasted to layered quasi-2D materials, such as ${\mathrm{high-T}}_c$ superconducting cuprates, intercalated graphite compounds or transition metal dichalcogenides, for which the theory explaining an onset of the CDWs constitutes a frontier of this fast-evolving field, strongly boosted by development of modern ab initio calculation methods. Full article

To date, the nitrogen metabolism pathways and salt-tolerance mechanisms of halophilic denitrifying bacteria have not been fully studied, and full-scale engineering trials with saline fly ash-washing wastewater have not been reported. In this study, we isolated and screened a halophilic denitrifying bacterium (Marinobacter sp.), GH-1, analyzed its nitrogen metabolism pathways and salt-tolerance mechanisms using whole-genome data, and explored its nitrogen removal characteristics under both aerobic and anaerobic conditions at different salinity levels. GH-1 was then applied in a full-scale engineering project to treat saline fly ash-washing leachate. The main results were as follows: (1) Based on the integration of whole-genome data, it is preliminarily hypothesized that the strain possesses complete nitrogen metabolism pathways, including denitrification, a dissimilatory nitrate reduction to ammonium (DNRA), and ammonium assimilation, as well as the following three synergistic strategies through which to counter hyperosmotic stress: inorganic ion homeostasis, organic osmolyte accumulation, and structural adaptations. (2) The strain demonstrated effective nitrogen removal under aerobic, anaerobic, and saline conditions (3–9%). (3) When applied in a full-scale engineering system treating saline fly ash-washing wastewater, it improved nitrate nitrogen (NO₃⁻-N), total nitrogen (TN), and chemical oxygen demand (COD) removal efficiencies by 31.92%, 25.19%, and 31.8%, respectively. The proportion of Marinobacter sp. increased from 0.73% to 3.41% (aerobic stage) and 2.86% (anoxic stage). Overall, halophilic denitrifying bacterium GH-1 can significantly enhance the nitrogen removal efficiency of saline wastewater systems, providing crucial guidance for biological nitrogen removal treatment. Full article

Urushiol, the principal bioactive component of natural lacquer, has emerged as a promising candidate for developing eco-friendly antimicrobial coatings due to its unique catechol structure and long alkyl chains. This review systematically elucidates the molecular mechanisms underpinning urushiol’s broad-spectrum antimicrobial activity, including membrane disruption via hydrophobic interactions, oxidative stress induction through redox-active phenolic groups, and enzyme inhibition via hydrogen bonding. Recent advances in urushiol-based composite systems—such as metal coordination networks, organic–inorganic hybrids, and stimuli-responsive platforms—are critically analyzed, highlighting their enhanced antibacterial performance, environmental durability, and self-healing capabilities. Case studies demonstrate that urushiol derivatives achieve >99% inhibition against both Gram-positive and Gram-negative pathogens, outperforming conventional agents like silver ions and quaternary ammonium salts. Despite progress, challenges persist in balancing antimicrobial efficacy, mechanical stability, and biosafety for real-world applications. Future research directions emphasize precision molecular engineering, synergistic multi-target strategies, and lifecycle toxicity assessments to advance urushiol coatings in medical devices, marine antifouling, and antiviral surfaces. This work provides a comprehensive framework for harnessing natural phenolic compounds in next-generation sustainable antimicrobial materials. Full article

Curtobacterium species are increasingly recognized as plant pathogens and soil decomposers, but their prevalence and function as plant endophytes in aerial organs are less clear. In this study, we isolated six endophytic Curtobacterium species from the fruits, flower petals (previously unreported) and stem tissue of plants from diverse environments and examined their general characteristics. We found that all Curtobacterium endophytes belonging to three major Curtobacterium clusters—C. oceanosedimentum (a group not previously recognized as endophytic), C. luteum and C. flaccumfaciens—shared some common features. All or nearly all isolates tested were pigmented, displayed moderate salt tolerance and, surprisingly, were psychrotolerant, being able to grow at 6 °C. The exception was a fruit C. luteum isolate that appears to have evolved thermotolerance (up to 45 °C) instead as a likely adaptation to its environment. All isolates were able to metabolize starch and casein and solubilize inorganic phosphate, indicating conserved secreted hydrolase activity, but only isolates in the C. oceanosedimentum group were able to absorb and metabolize citrate. Finally, all endophytes tested were able to ferment the plant sugars sucrose and fructose, while they differed in their ability to use other sugars. Thus, this study documents common traits and adaptations in various Curtobacterium endophytes, and the presence of these isolates in floral and fruit organs implies the possible seed-borne inheritance of these isolates. Full article

The periodate/hydrogen peroxide (PI/H₂O₂) system is a recently developed advanced oxidation process (AOP) characterized by its rapid reaction kinetics, making it highly suitable for continuous-flow applications compared to conventional batch systems. Despite its potential, no prior studies have investigated its performance under flowing conditions. This work presents the first application of the PI/H₂O₂ process in a tubular microreactor, a promising technology for enhancing mass transfer and process efficiency. The degradation of textile dyes (specifically Basic Yellow 28 (BY28)) was systematically evaluated under various operating conditions, including reactant concentrations, flow rates, reactor length, and temperature. The results demonstrated that higher H₂O₂ flow rates, increased PI dosages, and moderate dye concentrations (25 µM) significantly improved degradation efficiency, achieving complete mineralization at 2 mM PI and H₂O₂ flow rates of 80–120 µL/s. Conversely, elevated temperatures negatively impacted the process performance. The influence of organic and inorganic constituents was also examined, revealing that surfactants (SDS, Triton X-100, Tween 20, and Tween 80) and organic compounds (sucrose and glucose) acted as strong hydroxyl radical scavengers, substantially inhibiting dye oxidation—particularly at higher concentrations, where nearly complete suppression was observed. Furthermore, the impact of water quality was assessed using different real matrices, including tap water, seawater, river water, and secondary effluents from a municipal wastewater treatment plant (SEWWTP). While tap water exhibited minimal inhibition, river water and SEWWTP significantly reduced process efficiency due to their high organic content competing with reactive oxygen species (ROS). Despite its high salt content, seawater remained a viable medium for dye degradation, suggesting that further optimization could enhance process performance in saline environments. Overall, this study highlights the feasibility of the PI/H₂O₂ process in continuous-flow microreactors and underscores the importance of considering competing organic and inorganic constituents in real wastewater applications. The findings provide valuable insights for optimizing AOPs in industrial and municipal wastewater treatment systems. Full article

Atmospheric aqueous-phase reactions have been recognized as an important source of secondary organic aerosols (SOAs). However, the unclear reaction kinetics and mechanics hinder the in-depth understanding of the SOA sources and formation processes. This study selected ten different substituted phenolic compounds (termed as PhCs) emitted from biomass burning as precursors, to investigate the kinetics using OH oxidation reactions under simulated sunlight. The factors influencing reaction rates were examined, and the contribution of reactive oxygen species (ROS) was evaluated through quenching and kinetic analysis experiments. The results showed that the pseudo-first-order rate constants (k_obs) for the OH oxidation of phenolic compounds ranged from 1.03 × 10⁻⁴ to 7.85 × 10⁻⁴ s⁻¹ under simulated sunlight irradiation with an initial H₂O₂ concentration of 3 mM. Precursors with electron-donating groups (-OH, -OCH₃, -CH₃, etc.) exhibited higher electrophilic radical reactivity due to the enhanced electron density of the benzene ring, leading to higher reaction rates than those with electron-withdrawing groups (-NO₂, -CHO, -COOH). At pH 2, the second-order reaction rate (k_{PhCs, OH}) was lower than at pH 5. However, the k_obs did not show dependence on pH. The presence of O₂ facilitated substituted phenols’ photodecay. Inorganic salts and transition metal ions exhibited varying effects on reaction rates. Specifically, NO₃⁻ and Cu²⁺ promoted k_{PhCs, OH}, Cl⁻ significantly enhanced the reaction at pH 2, while SO₄²⁻ inhibited the reaction. The k_{PhCs, OH} were determined to be in the range of 10⁹~10¹⁰ L mol⁻¹ s⁻¹ via the bimolecular rate method, and a modest relationship with their oxidation potential was found. Additionally, multiple substituents can suppress the reactivity of phenolic compounds toward •OH based on Hammett plots. Quenching experiments revealed that •OH played a dominant role in phenolic compound degradation (exceeding 65%). Electron paramagnetic resonance confirmed the generation of singlet oxygen (¹O₂) in the system, and probe-based quantification further explored the concentrations of •OH and ¹O₂ in the system. Based on reaction rates and concentrations, the atmospheric aqueous-phase lifetimes of phenolic compounds were estimated, providing valuable insights for expanding atmospheric kinetic databases and understanding the chemical transformation and persistence of phenolic substances in the atmosphere. Full article

Leaching represents a significant challenge for the mining industry due to its slow and incomplete kinetics under ambient conditions (20 °C, 1 atm) and its increased prevalence in global ore deposits. In this context, the use of hydrogen peroxide (H₂O₂) has proved to be a promising oxidizing agent for improving process efficiency. This article reviews the most recent breakthroughs in the use of H₂O₂ for chalcopyrite leaching, analyzing the experimental conditions that maximize copper extraction, including combinations with novel leachants such as organic systems, inorganic salts, and amino acids. In addition, the main challenges associated with the use of H₂O₂, such as its catalytic decomposition and thermal stability, are highlighted, along with strategies to overcome these limitations. Perspectives and challenges for its application are presented, emphasizing the need for hybrid and optimized approaches to integrate this oxidizing agent in sustainable hydrometallurgical processes. The objective of this paper is to make an exhaustive review of what has been published on chalcopyrite leaching in order to find ways to leach it in large quantities and in a simple way. Full article

Ships and offshore equipment operating in marine environments often face issues such as seawater corrosion and biofouling, leading to significant economic losses. To address the corrosion problems of ships and offshore equipment, heavy-duty anticorrosive coatings are widely used for corrosion protection in marine environments due to their long-term effectiveness, cost-efficiency, and excellent applicability. In this study, silane coupling agent (KH-560) was employed to modify sodium silicate, and the modified sodium silicate was then incorporated as a reinforcing phase into polyurethane to ultimately prepare a modified sodium silicate/polyurethane coating. The feasibility of the modified sodium silicate/polyurethane coating was investigated by characterizing its conventional physicochemical properties, weather resistance, acid and alkali resistance, and salt spray corrosion resistance. Experimental results indicate that the silane coupling agent acts as a bridge between the organic and inorganic interfaces through the hydrolysis and condensation reactions of its bifunctional groups, forming an interfacial layer connected by hydrogen bonds and covalent bonds, thereby improving the compatibility between the organic resin and inorganic sodium silicate. Comprehensive performance analysis revealed that when the content of modified sodium silicate was 60 wt%, the coating hardness reached 4H. Additionally, electrochemical tests demonstrated that the coating exhibited higher impedance (9.62 × 10⁴ Ω/cm²) and lower corrosion current density (5.82 × 10⁻⁷ A/cm²). This study provides a theoretical and experimental basis for the development of high-performance anticorrosive coatings for marine applications. Full article

As key components in solid-state electrolytes, lithium salts influence the electrochemical window, ionic conductivity, and ultimately the full battery’s performance. To reduce the selection time and costs while providing electric and molecular level insights into the interactions of elements and components in solid polymer electrolytes, this paper proposes a rapid screening method based on Density Functional Theory (DFT). The structure stability, electrochemical stability, and ionic conductivity of eight common inorganic and organic lithium salts were systematically investigated by analyzing five parameters: formation energy, band gap, Li⁺–anion dissociation energy, anion–PEO binding energy, and anion diffusion barriers along PEO chains. Through a comprehensive analysis of these parameters obtained from DFT, LiTFSI has been identified as the most suitable lithium salt. The electrolytes fabricated by LiTFSI exhibited better performance. This approach, characterized by its rapidness, efficiency, and low cost, provides a viable method for screening lithium salts in developing solid-state batteries. Full article

Intensive and large-scale drip irrigation plays a crucial role in ensuring cotton production in Northwest China. However, significant differences in cotton production have occurred at times within large-scale irrigation systems, and quantitative information on the importance and interactions of factors related to cotton growth and constraints is scarce. In 2018–2019, we monitored six possible constraints (irrigation depth, soil texture, soil salt, soil moisture, soil inorganic nitrogen and soil organic matter) associated with drip irrigation management and seed cotton yields in a collective drip irrigation system (CDIS, composed of several drip irrigation subsystems (DISs)) in southern Xinjiang to assess the importance of different factors and identify the main constraints. In 2023, other more refined field trials were conducted to further evaluate the influencing mechanism of the main constraints on crop growth in one typical DIS within the selected CDIS. The results revealed large yield differences within the CDIS; although the average seed cotton yield was good (2018: 8051 kg ha⁻¹, 2019: 6617 kg ha⁻¹). Excessive irrigation depths (>500 mm) and coarse soil texture (sand content > 70%) were identified as the main constraints, affecting more than 45% of the plant area in the CDIS based on boundary line analysis (a typical analysis method to study the responses between variables) The results from the DISs revealed that the two constraints directly affected the soil moisture and soil inorganic nitrogen in the root zone, which reduced the effectiveness of irrigation and fertilization under drip irrigation. The Structural Equation Model (used to evaluate the causal relationships among multiple variables) revealed that both irrigation depth and soil texture indirectly affect yield by affecting soil inorganic nitrogen and plant N uptake and that soil nitrogen management is critical in resisting yield decline caused by constraints. An optimized irrigation schedule, improved uniformity of the drip irrigation network and adjusted drip fertilization strategies could be used for site-specific management to address the yield decline due to the main constraints and improve water and fertilizer use efficiency under drip irrigation management. Full article

Marine-derived biomaterials are emerging as promising candidates for tissue regeneration due to their sustainability, biocompatibility, bioactivity, and unique chemical structure. This review provides an overview of different marine-derived inorganic and organic materials, such as calcium carbonate, magnesium salts, silica, polysaccharides, bioactive peptides, and lipid-based compounds, and their effects in promoting osteogenesis. Specifically, the osteoinductive, osteoconductive, and osteointegrative activities of traditional and innovative materials that influence key molecular pathways such as BMP/Smad and Wnt/β-catenin signaling underlying bone formation will be evaluated. This review also prospects innovative approaches, i.e., phage display technology, to optimize marine-derived peptides for targeted bone regeneration. In the context of innovative and sustainable materials, this review suggests some interesting applications of unusual materials able to overcome the limitations of conventional ones and stimulate cellular regeneration of bone tissue by activating specific molecular pathways. Full article

Aqueous zinc batteries are emerging technologies for energy storage, owing to their high safety, high energy, and low cost. Among them, the development of low-cost and long-cycling cathode materials is of crucial importance. Currently, Zn-ion cathodes are heavily centered on metal-based inorganic materials and carbon-based organic materials; however, the metal–organic compounds remain largely overlooked. Herein, we report the electrochemical performance of metal phthalocyanines, a large group of underexplored compounds, as alternative cathode materials for aqueous zinc batteries. We discover that the selection of transition metal plays a vital role in affecting the electrochemical properties. Among them, iron phthalocyanine exhibits the most promising performance, with a reasonable capacity (~60 mAh g⁻¹), a feasible voltage (~1.1 V), and the longest cycling (550 cycles). The optimal performance partly results from the utilization of zinc chloride “water-in-salt” electrolyte, which effectively mitigates material dissolution and enhances battery performance. Consequently, iron phthalocyanine holds promise as an inexpensive and cycle-stable cathode for aqueous zinc batteries. Full article

Significant progress has been achieved in the development of superabsorbent polymers (SAPs), focusing on enhancing their performance and expanding their applications. Efforts are particularly directed at increasing water absorbency while promoting environmental sustainability. Biodegradable materials such as starch and potassium humate have been successfully integrated with SAPs for desert greening, improving water retention, salt resistance, and seedling survival. The inclusion of nutrient-rich organic-inorganic composites further enhances the durability, efficiency, and recyclability of SAPs. In drought mitigation, polymeric absorbent resins such as polyacrylamide and starch-grafted acrylates have shown efficacy in ameliorating soil conditions and fostering plant growth. In arid environments, agents enriched with humic acid and bentonite contribute to improved soil aeration and water retention, creating optimal conditions for plant establishment. Additionally, the adoption of innovative waste management solutions has led to the production of amphiphilic SAPs from residual sludge, effectively addressing soil nutrient deficiencies and environmental pollution. In the food industry, SAPs containing protease, tea polyphenols, and chitosan exhibit potential for enhancing the stability and quality of seafood products. These advancements highlight the growing relevance of structural optimization approaches in SAP development across diverse applications and underline the importance of continued innovation in these fields. As novel materials emerge and environmental challenges intensify, the potential applications of SAPs are anticipated to expand significantly. Full article