Search Results (234)

The impact of modulation periods on the microstructure, as well as the tribological and mechanical characteristics of the AlCrTiVNbN/TiSiN nano multilayer films, was investigated. The films were prepared with modulation periods ranging from 4 nm to 7 nm, and their properties were explored using X-ray diffraction (XRD), scanning electron microscope (SEM), nanoindentation, and a tribological tester. All nano multilayer films revealed a face-centered cubic (FCC) structure with a preferred planar direction of (200). As the modulation period increased, the XRD peak moved to higher angles, and the interplanar distance decreased. Also, the mechanical properties deteriorated, and the COF rose monotonically as a result. The nano multilayer film with a modulation period equal to 4 nm exhibited a smooth surface with minimal small particles, the highest hardness of 15.51 ± 0.16 GPa and elastic modulus of 182.89 ± 2.38 GPa, the highest values for the ratios of H/E and H³/E², the lowest average friction coefficient of 0.73, and a wear rate equal to (8.2 9 ± 0.18) × 10⁻⁸ mm³·N⁻¹·m⁻¹. The improvement in the properties of the film was ascribed to the coherent growth and alternating stress field between the AlCrTiVNbN and TiSiN layers. Full article

Nanostructured multilayer anticorrosion coatings offer an effective strategy to mitigate the poor corrosion resistance of aluminum alloys and extend their service life. In this study, four types of Ti/Cr multilayer coatings with varied modulation periods along the growth direction were deposited on 7050 aluminum alloy substrates using direct current magnetron sputtering. The cross-sectional microstructure of the coatings was characterized by scanning electron microscopy (SEM), while their mechanical and corrosion properties were systematically evaluated through nanoindentation and electrochemical measurements. The influence of modulation period distribution on the corrosion resistance of Ti/Cr multilayers was thoroughly investigated. The results show that the average thickness of the Ti/Cr multilayer coatings is 680 nm, the structure is dense, and the coarse columnar crystals are not seen. All Ti/Cr multilayer coatings significantly reduced the corrosion current density of 7050 aluminum alloy by about 10 times compared with that of the substrate, showing good protective effect. Modulation period along the coating growth direction decreases the Ti/Cr multilayer coating surface heterogeneous interface density increases, inhibits the formation of corrosion channels, hindering the penetration of corrosive media, and the other three coatings and aluminum alloy compared to its corrosion surface did not see obvious pore corrosion, showing the most excellent corrosion resistance. Full article

Residual stress plays a crucial role in determining the structural reliability and mechanical performance of nano-multilayers. In the present study, nano-multilayers composed of ZrO_xN_y and V₂O₃ were deposited via magnetron sputtering, with the N:Ar flow ratio systematically varied during the process. Through the precise control of the deposition conditions, the compressive residual stress within the films was effectively reduced to approximately 0 GPa, thereby improving their mechanical robustness. It was observed that the optimization of the stress distribution was strongly influenced by the structural symmetry of the multilayer configuration. This symmetrical design not only mitigated stress accumulation but also ensured uniform mechanical response throughout the multilayer structure. The results from nanoindentation testing revealed a steady hardness value near 10.6 GPa. Furthermore, the maximum H³/E² and H/E ratios recorded were 0.054 GPa and 0.073, respectively, suggesting enhanced resistance to both plastic deformation and cracking. Full article

Lightweight, high-temperature thermal insulation materials play a critical role in aerospace applications, where extreme temperature conditions necessitate lightweight, high-performance solutions. This paper explores advancements in lightweight, high-temperature insulation materials specifically designed for aerospace environments, focusing on innovative flexible ceramic fiber felts, thermal insulation tiles, nano-insulation materials (aerogels), and multilayer insulations (MLIs). These materials exhibit superior thermal resistance, low density, and durability under dynamic and harsh conditions. Key developments include the integration of nanostructures to enhance thermal conductivity control and improve mechanical stability. This paper also highlights applications in spacecraft thermal protection systems, providing insights into the challenges of future material design strategies. These advancements underscore the growing potential of thermal insulations to improve energy efficiency, safety, and performance in aerospace missions. Full article

In this study, as-cast ductile iron was austempered to produce austempered ductile iron (ADI). A CrAlSiN film was then deposited on the surface of ADI specimens using the cathodic arc deposition (CAD) method. The gas flow ratio of Ar/N₂ varied (2, 2.5, and 3) under different processing parameters, designated as S1, S2, and S3, respectively. The composition, structure, hardness, adhesion, and wear resistance of the coated specimens were analyzed to evaluate the effect of the gas flow ratio on surface hardness and abrasion resistance. The experimental results indicated that CrN/Al(Si)N nano-multilayered films were successfully synthesized using oppositely positioned dual targets (Cr and AlSi) reacting with N₂ gas during the CAD process. The coatings significantly enhanced the surface hardness and wear resistance of ADI. A comparison of the three coating conditions with varying gas flow ratios revealed that as the Ar/N₂ gas flow ratio decreased (i.e., N₂ gas flow increased), the surface hardness of the coated ADI specimens increased while the abrasion rate decreased. Among the tested conditions, S1 exhibited the highest hardness (1479 HV_0.1) and the lowest wear rate (1.6 × 10⁻⁶ g/m). Full article

The spread of infectious diseases, such as COVID-19, presents a significant problem for public health and healthcare systems. Digital technology plays an important role in achieving access to healthcare by enhancing device connectivity and information sharing. This study aimed to develop, implement, and demonstrate a tracking and surveillance system to enhance monitoring for emerging infectious diseases, focusing on COVID-19 patient profiling. The system integrates IoT-based wearable devices, an artificial intelligence (AI) camera for real-time monitoring, and a MySQL database for data management. The program uses Charts.js for data visualization and Longdo Map API for mapping, leveraging Jetson Nano boards, webcams, and Python (Version 3.9). We employed a classification technique to categorize patients into two groups: those with a positive mood and those with a negative mood. For comparing accuracies, we utilized three types of models: multilayer perceptron (MLP), support vector machine (SVM), and random forest. Model validation and evaluation were conducted using Python programming. The results of this study fall into three parts. The first part involved testing the monitoring and surveillance system. It was found that the system could receive information from the wearable device, display the received data in graph form, and notify the medical staff when examining symptoms to consider whether the patient should be taken to the hospital. The second part focused on testing the device, and it was found that it could measure body temperature, heart rate, and blood oxygen levels (SpO₂) and send those data to the database. The third part involved an AI camera test, and it was found that the most suitable algorithm to analyze the patient’s facial expressions was Random Forest. The results show that the system supports hospitals in managing COVID-19 and similar diseases by enabling timely interventions through facial expression analysis. Full article

Scaffolds play a crucial role in tissue engineering as regenerative templates. Fabricating scaffolds with good biocompatibility and appropriate mechanical properties remains a major challenge in this field. This study proposes a method for preparing multi-material scaffolds, enabling the 3D printing of collagen and thermoplastic elastomers at room temperature. Addressing the previous challenges such as the poor printability of pure collagen and the difficulty of maintaining structural integrity during multilayer printing, this research improved the printability of collagen by optimizing its concentration and pH value and completed the large-span printing of thermoplastic elastomer using a precise temperature-control system. The developed hybrid scaffold has an interconnected porous structure, which can support the adhesion and proliferation of fibroblasts. The scaffolds were further treated with different post-treatment methods, and it was proven that the neutralized and cross-linked collagen scaffold, which has both nano-fibers and a certain rigidity, can better support the osteogenic differentiation of bone marrow mesenchymal stem cells (BMSCs). The research results show that the collagen thermoplastic elastomer hybrid scaffold has significant clinical application potential in soft tissue and hard tissue regeneration, providing a versatile solution to meet the diverse needs of tissue engineering. Full article

Point-of-care (POC) antigen detection plays a crucial role in curbing the spread of viruses. Paper-based fluorescence aptasensors are expected to offer a low-cost tool to meet the needs of decentralized POC diagnosis. Herein, we report on a fluorescent paper-based sensing system for detecting the SARS-CoV-2 spike protein. The sensing system was constructed by loading multi-layer Nb₂C MXene nano-quenchers and carbon-dot-labeled aptamer (G-CDs@Apt) probes onto a mixed cellulose ester (MCE) paper substrate. On the Nb₂C MXene/G-CDs@Apt sensing paper, abundant G-CDs@Apt probes were attached to the multilayer MXene nano-quenchers and kept in a fluorescence-off state, while recognition of the target detached the G-CDs@Apt probes formed the nano--quenchers, resulting in fluorescence recovery of the sensing paper. The developed paper-based sensor performed well in the one-step detection of the SARS-CoV-2 S1 protein with a detection limit of 0.067 ng/mL (0.335 pg/test). The assay exhibited good selectivity and anti-interference in the detection of the SARS-CoV-2 S1 protein in artificial saliva. Moreover, the paper-based aptasensor was successfully used to detect the SARS-CoV-2 S1 protein in actual environmental samples with recoveries of 90.87–100.55% and relative standard deviations of 1.52–3.41%. The proposed technology provides a cost-effective alternative to traditional antibody test strips for a wide range of POC diagnostic applications. Full article

In the current study, the authors have listed the causes of common failures in hydro turbine blades. In the following, coatings, as one of the practical solutions that can be utilized in the hydropower industry, were selected for further investigation. In this regard, nanocoating technology is used to prevent the above-mentioned failures, as well as to extend the service lifetime of turbine blades, to increase the inspection time, i.e., the overhaul intervals, and to reduce repair costs. Therefore, firstly, the raw materials of runner blades in different types of turbines were checked. The collected data revealed that this equipment is usually made of stainless steel (i.e., 304 and 316L). Therefore, the main focus of the current research was a general investigation of the effects of different nanocoatings on the material properties, including the wear, corrosion, and erosion, of 304 and 316L steels. Finally, a coating process used in this industry that is suitable for overhaul rather than initial construction was investigated. The advantages of using nanocoatings compared to traditional coatings in this industry were enumerated. In addition, the effects of single-layer and multi-layer coatings with different compositions on the corrosion, wear, and erosion properties of each of these stainless steels were discussed. Eventually, considering the gaps in past research and summarizing the collected results, a future research direction was proposed, including different combinations of materials to create new nanocoatings (with different percentages of nano alumina and titanium carbide). Full article

With the rapid advancement of infrared detection technology, the development of infrared stealth materials has become a pressing need. The study of optical micro/nano infrared stealth materials, which possess selective infrared radiation properties and precise structural features, is of significant importance. By integrating deep reinforcement learning with a multilayer perceptron, we have framed the design of radiation-selective films as a reinforcement learning problem. This approach led to the creation of a Ge/Ag/Ge/Ag multilayer micro/nano optical film that exhibits infrared stealth characteristics. During the design process, the agent continuously adjusts the thickness parameters of the optical film, exploring and learning within the defined design space. Upon completion of the training, the agent outputs the optimized thickness parameters. The results demonstrate that the film structure, optimized by the agent, exhibits a low average emissivities of 0.086 and 0.147 in the 3∼5 µm and 8∼14 µm atmospheric windows, respectively, meeting the infrared stealth requirements in terms of radiation characteristics. Additionally, the film demonstrates a high average emissivity of 0.75 in the 5∼8 µm range, making it effective for thermal radiation management. Furthermore, we coated the Si surface with the designed thin film and conducted experimental validation. The results show that the coated material exhibits excellent infrared stealth properties. Full article

Traditional binary coatings like TiN and CrN display limited thermal stability and wear resistance under extreme conditions. High-entropy alloy nitride (HEAN) coatings offer a promising solution due to their customizable composition and unique properties, including high hardness, corrosion resistance, and thermal stability. This study focused on (AlCrNbTaTi)N HEAN coatings to address a critical need for materials capable of enduring extreme mechanical and tribological demands by examining the impact of aluminum content on their structural and mechanical properties, providing insights for optimizing coatings in harsh conditions through a self-assembled nanolayer structure with enhanced resilience and performance. The coatings were deposited via a cathodic arc by employing an AlCrNbTaTi alloy target composed of aluminum (20, 50, 60, 70%) and equal molar ratios of Cr, Nb, Ta, and Ti. The coatings were characterized through grazing incidence X-ray diffraction, SEM, HR-TEM, a nano-indentation test, and a friction and wear test. The results indicated that with increasing Al content, the structure of (AlCrNbTaTi)N coatings shifted from FCC to an amorphous state, leading to a reduction in the hardness and elastic modulus, accompanied by an increase in the wear rate and friction coefficient. The (AlCrNbTaTi)N coating, with an equal atomic ratio of metallic elements, showed potential as a hard tool coating. It demonstrated outstanding mechanical and tribological properties, with a 34.5 GPa hardness, 369 GPa modulus, 0.35 friction coefficient, and 8.2 × 10⁻¹⁹ m²·N⁻¹ wear rate. The findings highlight the potential of (AlCrNbTaTi)N coatings to extend tool life and improve operational efficiency, helping advance materials engineering for industrial applications. Full article

The present study introduces an innovative blown coextrusion die technology designed to address a critical gap in the production of multilayer films. Unlike conventional systems, this novel die allows for the creation of films with a high number of layers, ensuring layer integrity even in the micro-nano scale. A key advancement of this die is its ability to increase the number of layers without extending the residence time since it does not require an additional multiplier element. The risk of thermal degradation can, thus be, minimized. The die can easily be combined with existing cast coextrusion technologies, making it very versatile. Stability maps were developed to define processability and, in association with rheological analysis, optimal processing windows were determined. This study highlights the potential of enhancing material efficiency by increasing the number of layers while reducing the need for high percentages of EVOH. The produced multilayer films exhibited strong layer adhesion without the use of tie layers, thus improving recyclability and supporting sustainability goals. Full article

This study addresses the issues of the limited data storage capacity of Argo buoys and satellite communication charges on the basis of data volume by proposing a block lossless data compression method that combines bidirectional long short-term memory networks and multi-head self-attention with a multilayer perceptron (BiLSTM-MHSA-MLP). We constructed an Argo buoy data compression system using the main buoy control board, Jetson nano development board, and the BeiDou-3 satellite transparent transmission module. By processing input sequences bidirectionally, BiLSTM enhances the understanding of the temporal relationships within profile data, whereas the MHSA processes the outputs of the BiLSTM layer in parallel to obtain richer representations. Building on this preliminary probability prediction model, a multilayer perceptron (MLP) and a block length parameter (block_len) are introduced to achieve block compression during training, dynamically updating the model and optimizing symbol probability distributions for more accurate predictions. Experiments conducted on multiple 4000 m single-batch profile datasets from both the PC and Jetson nano platforms demonstrate that this method achieves a lower compression ratio, shorter compression time, and greater specificity. This approach significantly reduces the communication time between Argo buoys and satellites, laying a foundation for the future integration of Jetson Nano into Argo buoys for real-time data compression. Full article

In this study, an inorganic multilayer barrier film was fabricated on the polyethylene naphthalate (PEN) substrate, which was composed of a SiO₂ layer prepared by inductively coupled plasma chemical vapor deposition (ICP-CVD) and a Al₂O₃/ZnO nanolaminate produced by plasma-enhanced atomic layer deposition (PEALD). The multilayer composite film with a structure of 50 nm SiO₂ + (4.5 nm Al₂O₃/6 nm ZnO) × 4 has excellent optical transmittance (88.1%) and extremely low water vapor permeability (3.3 × 10⁻⁵ g/m²/day, 38 °C, 90% RH), indicating the cooperation of the two advanced film growth methods. The results suggest that the defects of the SiO₂ layer prepared by ICP-CVD were effectively repaired by the PEALD layer, which has excellent defect coverage. And Al₂O₃/ZnO nanolaminates have advantages over single-layer Al₂O₃ due to their complex diffusion pathways. The multilayer barrier film offers potential for encapsulating organic electronic devices that require a longer lifespan. Full article

The simple oxides like titania, zirconia, and ZnO are famous with their antibacterial (or even antimicrobial) properties as well as their biocompatibility. They are broadly used for air and water filtering, in food packaging, in medicine (for implants, prostheses, and scaffolds), etc. However, these application fields can be broadened by switching to the composite multicomponent compounds (for example, titanates) containing in their unit cell, together with oxygen, several different metallic ions. This review begins with a description of the synthesis methods, starting from wet chemical conversion through the manufacturing of oxide (nano)powders toward mechanosynthesis methods. The morphology of these multicomponent oxides can also be very different (like thin films, complicated multilayers, or porous scaffolds). Further, we discuss in vitro tests. The antimicrobial properties are investigated with Gram-positive or Gram-negative bacteria (like Escherichia coli or Staphylococcus aureus) or fungi. The cytotoxicity can be studied, for example, using mouse mesenchymal stem cells, MSCs (C3H10T1/2), or human osteoblast-like cells (MG63). Other human osteoblast-like cells (SaOS-2) can be used to characterize the cell adhesion, proliferation, and differentiation in vitro. The in vitro tests with individual microbial or cell cultures are rather far away from the real conditions in the human or animal body. Therefore, they have to be followed by in vivo tests, which permit the estimation of the real applicability of novel materials. Further, we discuss the physical, chemical, and biological mechanisms determining the antimicrobial properties and biocompatibility. The possible directions of future developments and novel application areas are described in the concluding section of the review. Full article