Search Results (432)

To address the severe wear and galvanic corrosion of TC4/Mg three-dimensional interpenetrating composites caused by the potential difference and hardness disparity between the two phases, this work proposes a hybrid surface modification strategy combining plasma electrolytic oxidation (PEO) with a self-assembled monolayer (SAM) doped with multi-walled carbon nanotubes (MWCNTs). A PEO ceramic coating was first grown in situ on the composite surface, followed by sealing modification using MWCNTs-containing SAM. The microstructure, phase composition, tribological behavior and potentiodynamic polarization curves of the coatings were systematically evaluated. The results show that the PEO coating is mainly composed of Mg₂SiO₄, MgO, MgF₂ and TiO₂, exhibiting a typical porous structure. After the MWCNTs-doped SAM composite modification, the nano-fillers and the molecular layer synergistically seal the micropores and cracks, and the surface transforms into a continuous and dense layered morphology. Wear tests reveal that the composite coating reduces the friction coefficient to 0.195 and decreases the wear volume by 93.53% compared with the bare composite. The “micro-roller bearing” effect and debris adsorption of MWCNTs significantly improve the wear resistance, and the dominant wear mechanism changes from abrasive wear to three-body wear. Electrochemical measurements show that the corrosion current density of the composite coating decreases from 2 × 10⁻⁴ A·cm⁻² (bare composite) to 1.401 × 10⁻⁹ A·cm⁻², i.e., a reduction by five orders of magnitude, with a protection efficiency of 99.99%. This is attributed to the physical barrier effect of the PEO coating and the synergistic sealing of defects, as well as the blocking of electron transfer by MWCNTs/SAM. The multi-level protection system of “PEO + MWCNTs + SAM” constructed in this work achieves a synergistic improvement in both wear resistance and corrosion resistance of the TC4/Mg two-phase interpenetrating composite, and holds promise for further investigation as an osseointegration implant material. Full article

Blue honeysuckle (Lonicera caerulea L.) is subject to environmental stressors, leading to variability in both severe fruit drop during development and fruit quality. Zinc, an essential micronutrient, is critical to sustainable fruit tree production by enhancing yield and nutritional quality. Different forms of zinc fertilizers, particularly nano-zinc versus conventional ionic zinc, exhibit marked differences in absorption efficiency and agronomic performance, thereby determining their practical efficacy. In this two-year study, we evaluated the effects of foliar-applied zinc forms, ZnO nanoparticles (30, 50, and 90 nm) and ionic zinc (ZnCl₂ and ZnSO₄), applied at the young fruit, veraison, and maturity stages on yield and fruit quality. Results showed that ZnO nanoparticles were more effective than ionic zinc at 80 mg/L. In particular, among the ZnO NP treatments, 90 nm ZnO NPs exhibited the best overall effect, significantly improving fruit quality. The 30 nm ZnO NPs treatment performed best in terms of single fruit weight, yield per plant, and fruit firmness. This study highlights the potential of nano-zinc to enhance productivity and quality in blue honeysuckle, providing a theoretical basis for selecting optimal zinc fertilizer types and particle sizes in specialty berry production, with implications for sustainable, high-quality fruit cultivation. Full article

Micro- and nano-container-based self-healing coatings have emerged as a promising strategy for the long-term conservation of cultural heritage artifacts, including metals, stone, organic matter, and construction materials. These coatings incorporate microcapsules or nanocapsules with tailored shell and core materials, enabling autonomous release of healing agents or corrosion inhibitors in response to damage. For metallic artifacts, benzotriazole@mesoporous silica nanoparticles (BTA@MSN) microcapsules achieve selective pH-responsive release, reaching 77% at pH 9.0 and 42% at pH 5.0, effectively mitigating localized corrosion. Temperature-adaptive poly(methyl methacrylate-co-methacrylic acid) (PMMA-MA)/MgO microcapsules exhibit controlled rupture rates, with a 75% reduction at elevated temperatures, enhancing crack repair efficiency by approximately 5%. Organic artifacts, such as wooden or paper manuscripts, benefit from clove oil nanocapsules, which increase tensile strength by 43.5% and fracture toughness by 101.9%, with only 2.91% weight loss over 7 days compared to 33.1% for unencapsulated oil. Advanced fabrication methods—including microfluidics, Pickering emulsions, and multi-core systems—enable high encapsulation efficiency (up to 73.5%), uniform particle size, and repeatable healing. Multi-stimuli responsiveness (pH, temperature, light, magnetic fields) and biobased, environmentally friendly materials further enhance adaptability and sustainability. In this review, “self-healing” is defined broadly to include both physical crack repair and autonomous restoration of protective functions. Overall, self-healing micro/nanocapsule coatings provide a highly controllable, efficient, and durable solution for active heritage protection, representing a shift from passive to intelligent conservation strategies. Furthermore, a systematic comparison of different capsule systems is provided to clarify their respective advantages and limitations. Overall, hybrid systems exhibit the most balanced performance, while inorganic nanocontainers offer superior stability and controlled release, and polymeric capsules enable rapid healing but limited reusability. Full article

Naked oat (Avena nuda L.) is an important dual-purpose crop for grain and forage in cold regions; however, its high fatty acid content renders seeds prone to deterioration during storage. This study aimed to investigate the protective effects of zinc oxide nanoparticles (ZnO NPs) on artificially aged naked oat seeds and elucidate the underlying molecular mechanisms. Non-aged seeds (Naged) were subjected to artificial aging at 45 °C and 100% relative humidity for 24 h (Aged), followed by priming with 30 mg L⁻¹ ZnO NPs for 6 h (Daged). Antioxidant enzyme activities were determined spectrophotometrically, and transcriptome sequencing was performed on an Illumina platform to identify differentially expressed genes (DEGs) and enriched pathways. We found that ZnO NPs increased catalase (CAT), peroxidase (POD) and superoxide dismutase (SOD) activities by 3–4-fold, restored germination rate from 75% to 98%, and enhanced seed vigor index. A total of 21,403 DEGs were detected, with 15,841 stably expressed in response to nano-priming. Reactive oxygen species (ROS) burst rapidly induced up-regulation of AP2/EREBP transcription factor family members, which subsequently activated antioxidant enzyme genes to maintain cellular redox homeostasis. Metabolic pathway analysis demonstrated that the phenylpropanoid pathway was reprogrammed, characterized by down-regulated lignin biosynthesis and up-regulated flavonoid production, thereby enhancing ROS scavenging capacity. Additionally, the pentose phosphate pathway was activated to provide additional NADPH for antioxidant defense, and up-regulated ADP-glucose pyrophosphorylase (AGPase) facilitated starch accumulation. Notably, the 40S ribosomal protein S13 exhibited the highest connectivity in protein–protein interaction networks, was up-regulated 2.1-fold, and was enriched in post-translational modification processes. These findings suggest that nano-priming with ZnO NPs represents a promising biotechnological strategy for enhancing seed vigor and storability in naked oat, with potential applications in sustainable agriculture and the seed industry. Full article

Removing trace amounts of dissolved organic matter (DOM) has always been a significant issue in the field of environmental science and engineering. Herein, a UV-coupled O₃ micro-nano bubble (O₃-MNB) system was constructed, demonstrating superior efficiency in eliminating DOM compared to bulk O₃-MNB oxidation and direct UV photolysis. Various advanced analytical techniques, including in situ electron paramagnetic resonance, Fourier transform infrared spectroscopy and three-dimensional excitation–emission matrix, were employed to reveal the mechanism of the reaction process. Benefiting from the abundant interfacial area and enhanced mass transfer efficiency provided by the micro-nano bubbles, along with the simultaneous generation of reactive oxygen species such as •OH through UV activation, the UV/O₃-MNB system demonstrates excellent performance in removing DOM, and more than 90% of the mineralization rate was achieved after 1 h reaction. Furthermore, the findings were verified using both municipal water and natural surface water, and the proposed system also shows advantages in energy consumption compared to direct UV irradiation and conventional O₃ treatment, with an energy consumption of 25 kWh/mg dissolved organic carbon. This study innovatively integrates UV light with O₃-MNB technology, offering novel insights for advanced water purification and providing valuable references for practical engineering applications. Full article

Low-temperature stress adversely impairs rice germination and seedling establishment. This study assessed a nano-bio-priming strategy using lecithin (L) and silicon dioxide nanoparticles (SiO₂ NPs) to enhance chilling tolerance. Two fragrant rice cultivars (Xiangyaxiangzhan and Meixiangzhan 2) were primed with six combinations of lecithin (0, 50, and 100 μmol·L⁻¹, denoted as L0, L1, and L2) and SiO₂ NPs (0 and 100 mg·L⁻¹, denoted as S0 and S1) and exposed to optimal temperature (25 °C) or low-temperature stress (15 °C). Low-temperature stress delayed germination onset by two days. Combined priming treatments L1S1 and L2S1 significantly alleviated this inhibitory effect. Crucially, cultivar-specific responses were evident in Meixiangzhan 2, where L1S1 increased the germination vigor index by 50.97%. Meanwhile, the effect was less pronounced or inhibitory at normal temperature in Xiangyaxiangzhan. Priming substantially enhanced seedling growth, and L2S1 maximally increased root and shoot length in Meixiangzhan 2 by 55.30% and 15.82%, respectively. Furthermore, biomass accumulation was strongly promoted. L1S1 increased total dry weight and total fresh weight in Meixiangzhan 2 by 19.64% and 23.48%, respectively. Physiologically, priming elevated chlorophyll and carotenoid contents upregulated the activities of superoxide dismutase (SOD), peroxidase (POD), and catalase (CAT), and increased levels of soluble protein and ascorbate (AsA), while maintaining nitrate reductase (NR) activity and hydrogen peroxide (H₂O₂) homeostasis. These physiological improvements were positively correlated with enhanced growth. Our findings demonstrate that co-priming with lecithin and SiO₂ NPs is a potent strategy for enhancing low-temperature tolerance, with efficacy depending on both the treatment combination and rice genotype. Full article

Micronutrient deficiencies and low nutrient-use efficiency remain critical constraints to sustainable crop production. This study tested the hypothesis that Zn- and Cu-doped MnFe₂O₄ spinel ferrite nanoparticles can function as an efficient multinutrient nanofertilizer to enhance fenugreek (Trigonella foenum-graecum L.) growth and physiological performance. Zn- and Cu-doped MnFe₂O₄ nanoparticles were synthesized via a sol–gel method and characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). The nanoparticles exhibited a cubic spinel structure with an average crystallite size of 27 nm and uniform incorporation of Zn and Cu within the MnFe₂O₄ lattice. Foliar application at different concentrations (100–500 mg/L) significantly improved seed germination, seed vigor, plant height, leaf number, stem thickness, biomass accumulation, and chlorophyll content compared with the untreated control. The 300 mg/L treatment consistently produced the greatest improvements, increasing plant height, biomass, and total chlorophyll content by more than 25–40% relative to control plants. Higher concentrations of T₅ resulted in diminished benefits, indicating a concentration-dependent response. These findings demonstrate that Zn- and Cu-doped MnFe₂O₄ nanofertilizer provides a balanced and bioavailable source of essential micronutrients, offering a promising nano-enabled strategy for improving nutrient use efficiency and sustainable fenugreek production. Full article

Ozonation is widely applied for refractory wastewater treatment, but its practical engineering is often limited by poor ozone mass transfer and low ozone utilization. In this study, micro-nano bubbles (MNBs) technology was employed to improve ozone delivery, and the performance of an O₃-MNBs system for treating coking reverse osmosis concentrate (ROC) was systematically compared with the conventional millimeter-sized ozone bubbles (O₃-MBs) system. To further promote oxidation, hydrogen peroxide (H₂O₂) was introduced, forming an O₃-MNBs/H₂O₂ system. Results showed that O₃-MNBs (D₅₀ = 36 μm) achieved a volumetric mass transfer coefficient 2.5 times higher than O₃-MBs. Under optimized conditions (pH: 7–9, ozone dosage: 10 mg/(L·min), temperature: 20–30 °C), COD removal in the O₃-MNBs system reached 34.9 ± 1.2%, nearly twice that of the O₃-MBs system, while the O/C ratio decreased by approximately 50% (4.7 ± 0.2), indicating enhanced ozone utilization efficiency. The addition of H₂O₂ further increased COD removal to 52.1 ± 2.9% and reduced the O/C ratio to 2.9 ± 0.2, reflecting strong synergistic effects. Moreover, the integration of MNBs and H₂O₂ effectively reduced energy consumption per unit of pollutant removed. Overall, the O₃-MNBs-based technology enhances organic pollutant degradation, ozone utilization and energy efficiency, offering a promising strategy for high-salinity refractory wastewater treatment. Full article

Salinity stress severely limits rice productivity and grain quality worldwide. Although exogenous foliar application of titanium dioxide nanoparticles (nano-TiO₂) has been reported to enhance crop stress tolerance, its regulatory roles in yield formation and grain quality in rice varieties with differing salt tolerance are not well understood. In the present study, two contrasting rice varieties, viz., Jingliangyou 3261 (JLY3261; salt-tolerant) and Yuxiangyouzhan (YXYZ; salt-sensitive), were applied with five nano-TiO₂ foliar application treatments—viz., CK: water spray; Ti1: 15 mg L⁻¹; Ti2: 30 mg L⁻¹; Ti3: 45 mg L⁻¹; and Ti4: 60 mg L⁻¹—at the jointing and panicle initiation stages. Plants were irrigated with 0.3% saltwater to simulate salt stress. The results showed that Ti2 and Ti3 treatments led to 8.59% and 14.80% increases in grain yield in JLY3261 and YXYZ, respectively, compared with CK. Ti2 and Ti3 treatments significantly increased the leaf area index, net photosynthetic rate, and aboveground biomass of both varieties at the heading stage. Meanwhile, the activities of antioxidant enzymes such as superoxide dismutase and peroxidase, as well as nitrogen metabolism enzymes including nitrate reductase and glutamine synthetase, were improved with a substantial reduction in malondialdehyde contents. Application of nano-TiO₂ upregulated the expression of ion transport-related genes such as OsSOSs, OsNHXs and OsHKTs, thus improving leaf K⁺ accumulation and reducing Na⁺ content to optimize the K⁺/Na⁺ ratio. In addition, Ti2 and Ti3 treatments improved the milled rice rate, head rice rate, and protein content, while they decreased the chalkiness degree of both rice cultivars. Principal component analysis showed that the aboveground biomass at the heading stage was a core evaluation index for both varieties. Overall, foliar application of 30–45 mg L⁻¹ nano-TiO₂ was found to be effective regarding growth and yield improvement in rice under saline conditions. This study provides a theoretical basis for agro-management strategies for rice cultivation in saline–alkaline soils. Full article

Porous Ca₂Mg₂Al₂₈O₄₆ (C₂M₂A₁₄) ceramics are highly competitive candidates in the field of critical metal filtration due to their attractive non-metallic-inclusions removal capacity. However, the low mechanical strength and inadequate thermal shock resistance (TSR) of these materials restrict their further application. In this work, ZrO₂-toughened C₂M₂A₁₄-based porous ceramics are fabricated by using the polymer sponge replica method. Nano-sized ZrO₂ particles derived from nano-ZrO₂ sol are beneficial to enhance the mechanical properties and TSR of porous ceramics. The optimized porous C₂M₂A₁₄ ceramics exhibit robust compressive strength (2.15 MPa), good residual strength ratio (66.4%) and excellent filtration efficiency in the reduction in total oxygen content (68.4%) by adding 3 wt% ZrO₂ sol. These excellent comprehensive properties show that as-prepared porous C₂M₂A₁₄ ceramics are promising candidate materials for application in the field of critical metal filtration. Full article

Nanotechnology holds great promise for alleviating drought stress in crops. This study elucidates and compares the distinct physiological mechanisms by which two nanomaterials, nano-cerium oxide (CeO₂) and nano-titanium dioxide (TiO₂), function as seed-priming agents to enhance drought tolerance in barley. A comprehensive analysis encompassing germination performance, hormonal dynamics, starch metabolism, osmotic adjustment, photosynthetic pigments, and the antioxidant system revealed that each nanomaterial operates through a unique pathway. Specifically, priming with 150 mg·L⁻¹ nano-CeO₂ (CP-150) primarily promoted root development and stress resilience. This effect was achieved by persistently reducing abscisic acid (ABA) levels, elevating gibberellin (GA₃), enhancing amylase activity to mobilize seed reserves, and increasing soluble protein accumulation in roots. In contrast, priming with 500 mg·L⁻¹ nano-TiO₂ (TP-500) was more effective in enhancing shoot physiology and adaptive capacity by rapidly inducing auxin (IAA), robustly stimulating the antioxidant enzyme system, and increasing photosynthetic pigment content. The temporally and spatially complementary actions of these nanomaterials, with nano-CeO₂ fostering root-based resilience and nano-TiO₂ boosting shoot-level functions, synergistically support seed germination and seedling establishment under drought conditions. This study provides a mechanistic foundation for designing targeted nano-priming strategies to improve crop drought resistance. Full article

This study investigated the combined effects of climate change-related salinity extremes and nanoparticle pollution on the seagrass Posidonia oceanica and the macroalga Caulerpa prolifera. Both species were exposed, individually and in co-occurrence, to different salinity regimes (34; 38 and 42 g kg⁻¹) and to the emerging contaminant nano-TiO₂ (0.7 mg L⁻¹, environmentally relevant concentration, and 5.0 mg L⁻¹, high-stress exposure). Biochemical and physiological responses were assessed at baseline (T0) and after 3, 6, and 12 days of exposure, followed by a 12-day recovery phase to evaluate post-stress resilience. This multifactorial design enabled the evaluation of interactive and cumulative effects of salinity shifts associated with climate change and nanoparticle contamination. Results showed that P. oceanica was particularly sensitive to nano-TiO₂ at a concentration of42 g kg⁻¹. Reduced photosynthetic performance was associated with enhanced oxidative stress and limited recovery capacity, suggesting potential long-term impacts on meadow persistence and ecosystem functioning. In contrast, C. prolifera exhibited higher tolerance and recovery efficiency, potentially gaining a competitive advantage under climate-induced environmental variability and increasing the risk of seagrass decline and community shifts in coastal ecosystems. These biochemical markers of early stress do not necessarily reflect direct population effects, particularly in long-lived foundation species such as Posidonia oceanica. Full article

Titanium dioxide (TiO₂) nano- and submicrometric particles’ widespread use in different sectors raised concerns about human and environmental exposure. The validation of analytical methods is essential to ensure reliability in risk assessment studies. In this study, a single-particle inductively coupled plasma mass spectrometry (spICP-MS) method was validated for the detection, quantification, and dimensional characterization of TiO₂ particles in biological tissues. Tissue samples collected after exposure to TiO₂ particles underwent mild acidic digestion using a HNO₃/H₂O₂ mixture to achieve complete matrix decomposition while preserving particle integrity. The resulting digests were analyzed by ICP-MS operated in single-particle mode to quantify and size TiO₂ particles. Method validation was conducted according to ISO/IEC 17025:2017 and included linearity, repeatability, recovery, and detection limit assessments. The limit of detection for TiO₂ particles was 0.04 µg/g, and 55.7 nm was the size the detection limit. Repeatability was within 0.5–11.5% for both TiO₂ mass concentrations and particle size determination. The validated method was applied to tissues from inhalation-exposed subjects, showing TiO₂ levels of 80 ± 20 µg TiO₂/g and particle number concentrations of 5.0 × 10⁵ ± 1.2 × 10⁵ part. TiO₂/mg. Detected TiO₂ particles’ mean diameter ranged from 230 to 330 nm. The developed and validated spICP-MS method provides robust and sensitive quantification of TiO₂ particles in biological matrices, supporting its use in human biomonitoring and exposure assessment studies. Full article

In this study, magnesium-modified clinoptilolite (MZ) was successfully synthesized via precipitation and calcination to efficiently remove Pb(II) from aqueous solutions. The material was systematically characterized using BET, XRD, SEM-EDX, FT-IR, and XPS. Adsorption kinetics followed a pseudo-second-order model (R² = 0.9956), with MZ removing over 70% of Pb(II) within the first 3 h. Isotherm data were best described by the Langmuir model (R² = 0.9686), confirming monolayer chemical adsorption, with a maximum adsorption capacity (q_m) of 1656 mg/g. Notably, MZ maintained high adsorption capacity across a pH range of 3.0~5.5, and its performance was largely unaffected by the presence of high concentrations of competing ions (0.1~1.0 M NaNO₃). Mechanistic analysis revealed that the loaded MgO facilitates the chemical conversion of Pb(II) to hydroxycarbonate (Pb₃(CO₃)₂(OH)₂) via surface complexation, which constitutes the primary removal mechanism. These findings demonstrate that magnesium modification can transform natural zeolites into high-capacity, stable adsorbents, offering promising potential for the treatment of Pb(II)-contaminated water. Full article

This work presents a green chemistry route to obtain titanium dioxide TiO₂ nanoparticles with an average size of about 13.25 nm using lemongrass (Cymbopogon citratus) extract. For these assessments, TiO₂ nanoparticles were added to the coating at concentrations of 1% and 5% w/w on fiber-cement sheets. Self-cleaning evaluation was analyzed by the photodegradation of methylene blue (MB) dye at concentrations of 5, 10, and 20 mg/L applied to the coated sheet, and then exposed to simulated sunlight. The coating containing 5 wt% TiO₂ nanoparticles showed the highest photodegradation, reaching 93.3% after 4 h under simulated sunlight exposure at the lowest MB concentration (5 mg/L). Additionally, average contact angles of 80.4°, 92.03°, and 104.25° were determined for coatings containing 0%, 1%, and 5 wt% TiO₂, respectively. Moreover, the modified 5 wt% TiO₂ exhibited up to 30.9% greater hydrophobicity than the control. Antifungal efficacy against Aspergillus niger and Penicillium was evaluated using the Poisoned Food method with nanoparticles at concentrations of 1 and 3 mg/mL showing a moderate growth inhibition. In conclusion, the versatility demonstrated suggests potential applications such as a nano-additive for aqueous acrylic coatings, improving hydrophobicity, self-cleaning and antifungal properties, which could be attractive to the construction industry. Full article