Search Results (48)

AlGaN is attractive for fabricating deep ultraviolet (DUV) optoelectronic and electronic devices of light-emitting diodes (LEDs), photodetectors, high-electron-mobility field-effect transistors (HEMTs), etc. We investigated the quality and optical properties of Al_xGa_1−xN films with high Al fractions (60–87%) grown on sapphire substrates, including AlN nucleation and buffer layers, by metal–organic chemical vapor deposition (MOCVD). They were initially investigated by high-resolution X-ray diffraction (HR-XRD) and Raman scattering (RS). A set of formulas was deduced to precisely determine x(Al) from HR-XRD data. Screw dislocation densities in AlGaN and AlN layers were deduced. DUV (266 nm) excitation RS clearly exhibits AlGaN Raman features far superior to visible RS. The simulation on the AlGaN longitudinal optical (LO) phonon modes determined the carrier concentrations in the AlGaN layers. The spatial correlation model (SCM) analyses on E₂(high) modes examined the AlGaN and AlN layer properties. These high-x(Al) Al_xGa_1−xN films possess large energy gaps E_g in the range of 5.0–5.6 eV and are excited by a DUV 213 nm (5.8 eV) laser for room temperature (RT) photoluminescence (PL) and temperature-dependent photoluminescence (TDPL) studies. The obtained RTPL bands were deconvoluted with two Gaussian bands, indicating cross-bandgap emission, phonon replicas, and variation with x(Al). TDPL spectra at 20–300 K of Al_0.87Ga_0.13N exhibit the T-dependences of the band-edge luminescence near 5.6 eV and the phonon replicas. According to the Arrhenius fitting diagram of the TDPL spectra, the activation energy (19.6 meV) associated with the luminescence process is acquired. In addition, the combined PL and time-resolved photoluminescence (TRPL) spectroscopic system with DUV 213 nm pulse excitation was applied to measure a typical AlGaN multiple-quantum well (MQW). The RT TRPL decay spectra were obtained at four wavelengths and fitted by two exponentials with fast and slow decay times of ~0.2 ns and 1–2 ns, respectively. Comprehensive studies on these Al-rich AlGaN epi-films and a typical AlGaN MQW are achieved with unique and significant results, which are useful to researchers in the field. Full article

We present our recent development of the surface-emitting quantum cascade laser with a PC (photonic crystal) resonator and a strain-compensated MQW (multiple quantum well) active layer operating at around 4.3 μm. We describe the laser performance mainly from the viewpoint of the design and analysis of the PC resonators, which include both numerical calculations by FEM (finite element method) and analytical calculations using the k·p perturbation theory and group theory. We analyze the resonance quality factor, overlap factor, extraction efficiency, and far-field pattern, and show how the output power and beam quality have been improved by the appropriate design of the PC resonator. Full article

This investigation explores the structural and electronic properties of low-temperature-grown (InAs)₄(GaAs)₃/Be-doped InAlAs and InGaAs/Be-doped InAlAs multiple quantum wells (MQWs), utilizing migration-enhanced epitaxy (MEE) and conventional molecular beam epitaxy (MBE) growth mode. Through comprehensive characterization methods including transmission electron microscopy (TEM), Raman spectroscopy, atomic force microscopy (AFM), pump–probe transient reflectivity, and Hall effect measurements, the study reveals significant distinctions between the two types of MQWs. The (InAs)₄(GaAs)₃/Be-doped InAlAs MQWs grown via the MEE mode exhibit enhanced periodicity and interface quality over the InGaAs/Be-InAlAs MQWs grown through the conventional molecule beam epitaxy (MBE) mode, as evidenced by TEM. The AFM results indicate lower surface roughness for the (InAs)₄(GaAs)₃/Be-doped InAlAs MQWs by using the MEE mode. Raman spectroscopy reveals weaker disorder-activated modes in the (InAs)₄(GaAs)₃/Be-doped InAlAs MQWs by using the MEE mode. This originates from utilizing the (InAs)₄(GaAs)₃ short period superlattices rather than InGaAs, which suppresses the arbitrary distribution of Ga and In atoms during the InGaAs growth. Furthermore, pump–probe transient reflectivity measurements show shorter carrier lifetimes in the (InAs)₄(GaAs)₃/Be-doped InAlAs MQWs, attributed to a higher density of antisite defects. It is noteworthy that room temperature Hall measurements imply that the mobility of (InAs)₄(GaAs)₃/Be-doped InAlAs MQWs grown at a low temperature of 250 °C via the MEE mode is superior to that of InGaAs/Be-doped InAlAs MQWs grown in the conventional MBE growth mode, reaching 2230 cm²/V.s. The reason for the higher mobility of (InAs)₄(GaAs)₃/Be-doped InAlAs MQWs is that this short-period superlattice structure can effectively suppress alloy scattering caused by the arbitrary distribution of In and Ga atoms during the growth process of the InGaAs ternary alloy. These results exhibit the promise of the MEE growth approach for growing high-performance MQWs for advanced optoelectronic applications, notably for high-speed optoelectronic devices like THz photoconductive antennas. Full article

ZnO-based heterostructures are up-and-coming candidates for terahertz (THz) optoelectronic devices, largely owing to their innate material attributes. The significant ZnO LO-phonon energy plays a pivotal role in mitigating thermally induced LO-phonon scattering, potentially significantly elevating the temperature performance of quantum cascade lasers (QCLs). In this work, we calculate the electronic structure and absorption of ZnO/ZnMgO multiple semiconductor quantum wells (MQWs) and the current density–voltage characteristics of nonpolar m-plane ZnO/ZnMgO double-barrier resonant tunnelling diodes (RTDs). Both MQWs and RTDs are considered here as two building blocks of a QCL. We show how the doping, Mg percentage and layer thickness affect the absorption of MQWs at room temperature. We confirm that in the high doping concentrations regime, a full quantum treatment that includes the depolarisation shift effect must be considered, as it shifts mid-infrared absorption peak energy for several tens of meV. Furthermore, we also focus on the performance of RTDs for various parameter changes and conclude that, to maximise the peak-to-valley ratio (PVR), the optimal doping density of the analysed ZnO/Zn₈₈Mg₁₂O double-barrier RTD should be approximately ${10}^{18}{\mathrm{c}\mathrm{m}}^{-3}$, whilst the optimal barrier thickness should be 1.3 nm, with a Mg mole fraction of ~9%. Full article

In this study, we have fabricated a 368 nm LED with an epitaxial Indium Tin Oxide (ITO) contact layer. We analyze the thermal performance of the flip-chip LED with a symmetric electrode and metal reflective layer, applying ANSYS to build a coupled electro-thermal finite element model (FEM) of the temperature distribution in the multiple quantum wells (MQWs). We compare our system with the traditional Au-bump flip-chip LED and a flip-chip LED with a Distributed Bragg Reflector (DBR) layer. The simulation results have shown that the flip-chip LED with a metal reflective layer and symmetric electrode exhibits better heat dissipation performance, particularly at high input power. The influence of the insulating layer on the LED chip junction temperature is also examined. The simulation data establish an effect due to the thermal conductivity of the insulating layer in terms of heat dissipation, but this effect is negligible at an insulation layer thickness ≤1 µm. Full article

We propose a highly polarized vertical-cavity surface-emitting laser (VCSEL) consisting of staggered InGaN multiple quantum wells (MQWs), with the resonance cavity and polarization enabled by a bottom nanoporous (NP) n-GaN distributed Bragg reflectors (DBRs), and top TiO₂ high-index contrast gratings (HCGs). Optoelectronic simulations of the 612 nm VCSEL were systematically and numerically investigated. First, we investigated the influences of the NP DBR and HCG geometries on the optical reflectivity. Our results indicate that when there are more than 17 pairs of NP GaN DBRs with 60% air voids, the reflectance can be higher than 99.7%. Furthermore, the zeroth-order reflectivity decreases rapidly when the HCG’s period exceeds 518 nm. The optimal ratios of width-to-period (52.86 ± 1.5%) and height-to-period (35.35 ± 0.14%) were identified. The staggered MQW design also resulted in a relatively small blue shift of 5.44 nm in the emission wavelength under a high driving current. Lastly, we investigated the cavity mode wavelength and optical threshold gain of the VCSEL with a finite size of HCG. A large threshold gain difference of approximately 67.4–74% between the 0th and 1st order transverse modes can be obtained. The simulation results in this work provide a guideline for designing red VCSELs with high brightness and efficiency. Full article

Quantum-well intermixing (QWI) technology is commonly considered as an effective methodology to tune the post-growth bandgap energy of semiconductor composites for electronic applications in diode lasers and photonic integrated devices. However, the specific influencing mechanism of the interfacial strain introduced by the dielectric-layer-modulated multiple quantum well (MQW) structures on the photoluminescence (PL) property and interfacial quality still remains unclear. Therefore, in the present study, different thicknesses of SiO₂-layer samples were coated and then annealed under high temperature to introduce interfacial strain and enhance atomic interdiffusion at the barrier–well interfaces. Based on the optical and microstructural experimental test results, it was found that the SiO₂ capping thickness played a positive role in driving the blueshift of the PL peak, leading to a widely tunable PL emission for post-growth MQWs. After annealing, the blueshift in the InGaAs/AlGaAs MQW structures was found to increase with increased thickness of the SiO₂ layer, and the largest blueshift of 30 eV was obtained in the sample covered with a 600 nm thick SiO₂ layer that was annealed at 850 °C for 180 s. Additionally, significant well-width fluctuations were observed at the MQW interface after intermixing, due to the interfacial strain introduced by the thermal mismatch between SiO₂ and GaAs, which enhanced the inhomogeneous diffusion rate of interfacial atoms. Thus, it can be demonstrated that the introduction of appropriate interfacial strain in the QWI process is of great significance for the regulation of MQW band structure as well as the control of interfacial quality. Full article

Currently, GaN-based blue- and green-light-emitting devices have achieved successful applications in practice, while the luminescence efficiency of devices with longer wavelengths (such as yellow light) is still very low. Therefore, in this paper, the electroluminescence characterization of yellow-light-emitting InGaN/GaN multiple quantum wells (MQWs) with different In content in the last InGaN quantum well, which is next to the p-type GaN electrode layer, are investigated numerically to reveal a possible physical mechanism by which the different distribution of In content in the active region impacts the carrier capture and the light emission process in yellow InGaN/GaN MQWs. The simulation results show that at low injection currents, the luminescence efficiency of high-In-content yellow MQWs is enhanced, which can be ascribed to the enhanced radiative recombination process induced by the increased carrier concentration in the last InGaN quantum wells with promoted carrier capture ability. However, in the case of high injection condition, the luminescence efficiency of yellow MQWs deteriorates with increasing In content, i.e., the droop effect becomes remarkable. This can be ascribed to both significantly enhanced Auger recombination and electron leakage in the last InGaN quantum well, induced also by the promoted capture ability of charge carriers. Full article

Semipolar AlGaN multiple quantum wells (MQWs) have unique advantages in deep ultraviolet light emitters due to the weak Quantum-Confined Stark Effect. However, their applications are hampered by the poor crystalline quality of semipolar AlGaN thin films. Different treatments were developed to improve the crystal quality of semipolar AlGaN, including a multistep in situ thermal annealing technique proposed by our group. In this work, temperature-dependent and time-resolved photoluminescence characterizations were performed to reveal the carrier localization in the MQW region. The degree of carrier localization in semipolar AlGaN MQWs grown on top of the in situ-annealed AlN is similar to that of conventional ex situ face-to-face annealing, both of which are significantly stronger than that of the c-plane counterpart. Moreover, MQWs on in situ-annealed AlN show drastically reduced dislocation densities, demonstrating its great potential for the future development of high-efficiency optoelectronic devices. Full article

Recent experiments have shown that more than 85% of photo-generated carriers can escape from multiple quantum wells (MQWs) sandwiched between p-type and n-type layers (PIN). In this work, we quantitatively analyze the relationship between the energy of carriers and the height of potential barriers to be crossed, based on the GaAs/InGaAs quantum well structure system, combined with the Heisenberg uncertainty principle. It was found that that the energy obtained by electrons from photons is just enough for them to escape, and it was found that the energy obtained by the hole is just enough for it to escape due to the extra energy calculated, based on the uncertainty principle. This extra energy is considered to come from photo-generated thermal energy. The differential reflection spectrum of the structure is then measured by pump–probe technology to verify the assumption. The experiment shows that the photo-generated carrier has a longer lifetime in its short circuit (SC) state, and thus it possesses a lower structure temperature than that in open circuit (OC). This can only explain a thermal energy reduction caused by the continuous carrier escape in SC state, indicating an extra thermal energy transferred to the escaping carriers. This study is of great significance to the design of new optoelectronic devices and can improve the theory of photo-generated carrier transports. Full article

The studies of the interband electron transition energy in multiple Hg_1-xCd_xTe/Hg_1-yCd_yTe quantum wells (MQWs) at room temperature were carried out. The MQWs were grown on the (013) GaAs substrate by molecular beam epitaxy, with the layer composition and thickness being measured by the in-situ ellipsometric parameters measurement at the nanometer level. The Hg_1-xCd_xTe barrier composition and width were x = 0.69 and 30 nm, respectively. The Hg_1-yCd_yTe well composition was y = 0.06–0.10, and the width varied in the range of 2.7–13 nm. The experimental data of the interband electron transition energy were determined by the absorption spectral analysis. The calculation of the interband electron transition energy was carried out on the basis of the four-band Kane model. A good agreement between the experimental and calculated data was obtained. It was shown that MQWs may be used as a photosensitive material for creating infrared optoelectronic devices operating in different modes in the range of 3–10 μm at room temperature. Full article

In this research, we compared the performance of commercial μ-LEDs and three-layered staggered QW μ-LED arrays. We also investigated the self-heating effect. We proposed a green micro-resonant cavity light-emitting diode (µ-RCLED) that consists of a three-layer staggered InGaN with multiple quantum wells (MQWs), a bottom layer of nanoporous n-GaN distributed Bragg reflectors (DBRs), and a top layer of Ta₂O₅/SiO₂ DBRs. We systematically performed simulations of the proposed µ-RCLEDs. For the InGaN MQWs with an input current of 300 mA, the calculated wavefunction overlaps are 8.8% and 18.1% for the regular and staggered structures, respectively. Furthermore, the staggered MQWs can reduce the blue-shift of electroluminescence from 10.25 nm, obtained with regular MQWs, to 2.25 nm. Due to less blue-shift, the output power can be maintained even at a high input current. Conversely, by employing 6.5 pairs of Ta₂O₅/SiO₂ DBRs stacks, the full width at half maximum (FWHM) can be significantly reduced from 40 nm, obtained with ordinary µ-LEDs, to 0.3 nm, and a divergence angle smaller than 60° can be obtained. Our simulation results suggest that the µ-RCLEDs can effectively resolve the wavelength instability and color purity issues of conventional µ-LEDs. Full article

GaN cap layer with different thicknesses was grown on each InGaN well layer during MOCVD growth for InGaN/GaN multiple quantum well (MQW) samples to study the influence of the cap layer on the photoluminescence (PL) characteristics of MQWs. Through the temperature-dependent (TD) PL spectra, it was found that when the cap layer was too thick, the localized states of the quantum wells were relatively non-uniform. The thicker the well layer, the worse the uniformity of the localized states. Furthermore, through micro-area fluorescence imaging tests, it was found that when the cap layer was too thick, the luminescence quality of the quantum well was worse. In summary, the uniformity of the localized states in the quantum wells and the luminescence characteristics of the quantum wells could be improved when a relatively thin cap layer of the quantum well was prepared during the growth. These results could facilitate high efficiency QW preparation, especially for green LEDs. Full article

Electron leakage has an adverse influence on the optical output power for laser diodes (LDs), especially where the conventional last quantum barrier (LQB) in the multiple quantum well (MQW) active region may cause severe leakage problems. In this article, a composite last quantum barrier (CLQB) composed of p-type doped AlGaN (p-AlGaN) and unintentionally doped GaN (u-GaN) layers is designed to replace the conventional one, for overcoming the problem of electron overflow. Theoretical calculations with LASTIP software demonstrate that CLQB with optimized parameters of Al composition, thickness and p-type doping concentration of the p-AlGaN layer in the CLQB can have a 50% improvement in slope efficiency (SE) compared with the conventional structure LD. This will help to realize a higher optical output power in InGaN-based violet LDs. Full article

Metal halide perovskites have become a research highlight in the optoelectronic field due to their excellent properties. The perovskite light-emitting diodes (PeLEDs) have achieved great improvement in performance in recent years, and the construction of quasi-2D perovskites by incorporating large-size organic cations is an effective strategy for fabricating efficient PeLEDs. Here, we incorporate the fluorine meta-substituted phenethylammonium bromide (m-FPEABr) into CsPbBr₃ to prepare quasi-2D perovskite films for efficient PeLEDs, and study the effect of fluorine substitution on regulating the crystallization kinetics and phase distribution of the quasi-2D perovskites. It is found that m-FPEABr allows the transformation of low-n phases to high-n phases during the annealing process, leading to the suppression of n = 1 phase and increasing higher-n phases with improved crystallinity. The rational phase distribution results in the formation of multiple quantum wells (MQWs) in the m-FPEABr based films. The carrier dynamics study reveals that the resultant MQWs enable rapid energy funneling from low-n phases to emission centers. As a result, the green PeLEDs achieve a peak external quantum efficiency of 16.66% at the luminance of 1279 cd m⁻². Our study demonstrates that the fluorinated organic cations would provide a facile and effective approach to developing high-performance PeLEDs. Full article