Search Results (239)

Efficient utilization of low-calorific-value gases reduces emissions but remains challenging. Self-heat-maintained combustion uses fuel’s exothermic heat to sustain stability without external heat, yet the feed gas typically requires preheating (typically 573–673 K). This study innovatively proposes a compact regenerative catalytic reactor featuring an integrated helical heat-recovery structure and replaces empirical preheating with a user-defined function (UDF) programmed heat transfer efficiency model. This dual innovation enables self-sustained combustion at 0.16 vol.% methane, the lowest reported concentration for autonomous operation. Numerical results confirm stable operation under ultra-lean conditions, with significantly reduced preheating energy demand and accelerated thermal response. Transient analysis shows lower space velocities enable self-maintained combustion across a broader range of methane concentrations. However, higher methane concentrations require higher inlet temperatures for self-heat maintenance. This study provides significant insights for recovering energy from low-calorific-value gases and alleviating global energy pressures. Full article

With CO₂ generation and emissions requirements, the cement industry faces huge pressure for reducing carbon emissions. Choosing alternative fuels instead of coal is a promising approach. However, the fuel properties of the alternative fuels have not been comprehensively studied. In this work, the fifty typical alternative fuels were selected based on the compositions for different classifications, and the basic fuel properties including proximate analysis, ultimate analysis, and low calorific values were analyzed. Most fuels from plastics and clothes have relatively low moisture; the values of as-received basis moisture (M_ar) and air-dry basis moisture (M_ad) of the others are all lower than 30 wt%. However, the alternative fuels of plastic and cloth all have relatively high contents of air-dry basis volatile compounds (V_ad) (>60 wt%), and they all have low contents of air-dry basis fixed carbon (FC_ad) (commonly <20 wt%) and air-dry basis ash (A_ad) (<30 wt%). The air-dry basis carbon contents (C_ad) of plastics are higher than 40 wt%, while the C_ad values of biomass are lower than 50 wt%. As for air-dry basis hydrogen (H_ad), the contents are all lower than 14 wt% and relatively stable for different kinds of alternative fuels. As for air-dry basis nitrogen (N_ad), the contents are all lower than 9 wt%, and most of them are lower than 3 wt%. In addition, the contents of air-dry basis sulfur (S_ad) of different alternative fuels are also lower than 3 wt%, while plastics, biomass, and clothes are all lower than 1 wt%. Also, the low calorific values (Q_net,ar) for the alternative fuels of plastic are commonly high, and the values for biomass are commonly between 500 and 1500 kJ/kg, while Q_net,ar values for the alternative fuels of cloth and others vary. The fuel properties of the fifty typical alternative fuels can guide fuel selection and optimization when they are mixed for combustion with coals in cement decomposition furnaces. Full article

Co-combustion is regarded as an effective means for high-efficiency utilization of low-quality fuels. However, low-quality fuel has problems such as low energy density and high water content. The fuel quality and blending performance can be further optimized by the pretreatment of low-quality fuel, for example, calorific value, hydrophobicity, and NO conversion rate. Based on the idea of co-upgradation, this study systematically investigates the effects of integrated upgrading on fuel quality and hydrophobicity under different conditions. In this study, lignite and wheat straw were selected as research objects. The co-upgrading experiments of wheat straw and lignite were conducted at reaction temperatures of 170 °C, 220 °C, and 270 °C in flue gas and air atmospheres with biomass blending ratios of 0%, 25%, 50%, 75%, and 100%. SEM (scanning electron microscopy) and nitrogen (N₂) adsorption analyses showed that under low-temperature and low-oxygen conditions, organic components from biomass pyrolysis migrated in situ to cover the surface of lignite, resulting in a gradual smoothing of the fuel surface and a decrease in the specific surface area. Meanwhile, water reabsorption experiments and contact angle measurements showed that the equilibrium water holding capacity and water absorption capacity of the lifted fuels was weakened, and hydrophobicity was enhanced. Combustion kinetic parameters and pollutant release characteristics were investigated by thermogravimetric analysis (TGA) and isothermal combustion tests. It was found that co-upgradation could effectively reduce the reaction activation energy and NO conversion rate. Characterized by Raman spectroscopy (Raman) and X-ray photoelectron spectroscopy (XPS), in situ migration of organic components affected combustion reactivity by modulating changes in N-containing product precursors. The results showed that the extracted fuel with a 75% biomass blending ratio in the flue gas atmosphere exhibited the best overall performance at 220 °C, with optimal calorific value, combustion reactivity, and hydrophobicity. These findings may provide important theoretical foundations and practical guidance for the optimization of industrial-scale upgrading processes of low-quality fuels. Full article

The advantages of torrefaction preheating, including the production of a hydrophobic solid product, improved particle size distribution, enhanced fuel properties with fewer environmental issues, decreased moisture content, and reduced volatile content. In order to meet the technical requirements of biomass oriented value-added and energy saving and emission reduction, pine sawdust (PS) was taken as the research object, and the physicochemical properties of the PS samples preheated at a low temperature were analyzed by synchronous thermal analysis (TG-DSC), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscope (SEM), and organic element analyzer (EA). The effect of preheating at a lower temperature on the physicochemical properties of PS was discussed. The results showed that, under the preheating condition of 200 °C, compared with PS, the water content of PS-200 decreased by 3.23%, the volatile content decreased by 3.69%, the fixed carbon increased by 6.81%, the calorific value increased by 6.90%, the equilibrium water content decreases from 7.06% to 4.46%, and the hydrophobicity increases. This research, based on the improvement of the quality of agricultural and forestry waste and the promotion of the strategy of converting waste into energy, has contributed to the advancement of sustainable energy production. Full article

The generation of fine coal particles during mining and processing presents significant environmental and logistical challenges, particularly in coal-dependent, developing countries like South Africa (SA). This review critically evaluates the technical viability of fine coal briquetting as a sustainable waste-to-energy solution within a SA context, while drawing from global best practices and comparative benchmarks. It examines abundant feedstocks that can be used for valorization strategies, including fine coal and agricultural biomass residues. Furthermore, binder types, manufacturing parameters, and quality optimization strategies that influence briquette performance are assessed. The co-densification of fine coal with biomass offers a means to enhance combustion efficiency, reduce dust emissions, and convert low-value waste into a high-calorific, manageable fuel. Attention is also given to briquette testing standards (i.e., South African Bureau of Standards, ASTM International, and International Organization of Standardization) and end-use applications across domestic, industrial, and off-grid settings. Moreover, the review explores socio-economic implications, including rural job creation, energy poverty alleviation, and the potential role of briquetting in SA’s ‘Just Energy Transition’ (JET). This paper uniquely integrates technical analysis with policy relevance, rural energy needs, and practical challenges specific to South Africa, while offering a structured framework for bio-coal briquetting adoption in developing countries. While technical and economic barriers remain, such as binder costs and feedstock variability, the integration of briquetting into circular economy frameworks represents a promising path toward cleaner, decentralized energy and coal waste valorization. Full article

The modern world has brought extensive socioeconomic and ecological changes. Urbanization in developing nations has significantly increased municipal solid waste, necessitating in-depth understanding of waste composition particularly in developing nations for sustainable management practices. This study aimed to classify and characterize waste while evaluating potential waste management methods. Mixed methods were used to examine landfilled waste from Soshanguve and Hatherley sites in Tshwane Metropolitan, South Africa, using techniques such as Fourier transform infrared spectroscopy, X-ray fluorescence, proximate, and ultimate analysis. Seasonal variations in waste components were analysed over two seasons. The study identified that both sites are predominantly composed of organic waste, accounting for over 42 wt.%, with moisture content of ~50 wt.%, and minimal recyclables (<5 wt.%). Seasonal variations in MSW were significant for glass (<4% increase), organic waste (<5% increase), while plastic decreased by ~7% during spring. The biodegradable waste showed high carbon (>50%) and oxygen (>40%) levels, low ash content (<18%), and calorific values of 15–19 MJ/kg. Biodegradables mainly contained oxides of calcium, silicon, iron (III), and potassium with chemical composition indicating functional groups that emphasize composting and energy recovery benefits. The research provides insights into sustainable waste management, revealing waste composition at Tshwane landfills, aiding informed decision-making for resource usage and environmental conservation. Full article

In order to cope with the emergence of energy conservation and consumption reduction initiatives, we used an acrylic emulsion (as the adhesive), combined with silica aerogel (SA) and hollow glass microsphere (HGM) fillers, to synthesize thermal insulation coatings, which were found to have low thermal conductivity and excellent thermal insulation properties. These waterborne coatings are environmentally friendly and were synthesized without organic solvents. Comprehensive testing verified that the coatings met practical requirements. Specifically, the addition of 18% SA resulted in minimal thermal conductivity (0.0433 W/m·K), the lowest density (0.177 g/cm³), as well as a reduced gross calorific value. At a heating surface temperature of 200 °C, the 5 mm coating’s cooling surface temperature was 108.7 °C, yielding a 91.3 °C temperature difference and demonstrating remarkable thermal insulation performance. Furthermore, the coatings showed favorable results in terms of water resistance, corrosion resistance, wear resistance, and adhesion, achieving satisfactory engineering standards. In this work, the influence of different contents of SA on various properties of the coating was studied, with the aim of providing a reference for the modulation of the comprehensive performance of SA thermal insulation coatings. Full article

This work investigated the effect of experimental conditions of dry and wet torrefaction on the properties of olive leaves and olive pomace. Torrefaction improved the fuel properties of olive waste. According to Van Krevelen parameters (O/C and H/C ratios), torrefied biomass, tested as solid biofuel, achieved a similar quality threshold to lignite. For example, dry torrefaction conducted at 230 °C for 80 min reduced the O/C and H/C ratios of olive leaves from 0.51 and 1.51 for raw biomass to 0.25 and 1.17 for torrefied biomass, respectively. Under the same conditions, the O/C and H/C ratios of olive pomace were also reduced from 0.34 and 1.60 to 0.27 and 1.36, respectively. Calorific values of raw olive leaves and olive pomace amounted to 18.0 and 23.2 MJ/kg, respectively. Following dry torrefaction and biomass conversion into biochar, calorific values of olive leaves and olive pomace increased by 24% and 14% up to 22.2 and 26.3 MJ/kg through dry torrefaction, compared with 17% and 23% increments up to 21.1 and 28.5 MJ/kg through wet torrefaction, respectively. Interestingly, biomass processing through wet torrefaction performed in a fluidized bed powered by superheated steam could be completed 8- to 12-fold more rapidly than dry torrefaction. SEM analysis indicated a breakdown of the surface structure of olive waste following the torrefaction process. According to the Brunauer–Emmett–Teller (BET) method, total pore surface areas of biochar obtained from wet torrefaction of olive pomace and olive leaves amounted to 3.6 m²/g and 0.8 m²/g, with total pore volumes amounting to 0.0225 cm³/g and 0.0103 cm³/g, respectively. Maximal contents of 5-hydroxymethylfurfural and furfural in liquid by-products from dry torrefaction amounted to 1930 and 1880 mg/1 kg, respectively. Alternately, in liquid by-products from wet torrefaction, concentrations of these high-value compounds remained very low. Full article

Plastic waste is currently a major concern in Romania due to the annual increase in quantities generated from anthropogenic and industrial activities, especially from end-of-life vehicles (ELVs), and the need to reduce environmental impact. This study investigates an alternative valorization route for polypropylene (PP) and polyethylene (PE) plastic waste through microwave-assisted pyrolysis, aiming to maximize conversion into gaseous products, particularly hydrogen-rich gas. A monomode microwave reactor was employed, using layered configurations of plastic feedstock, silicon carbide as a microwave susceptor, and activated carbon as a catalyst. The influence of catalyst loading, reactor configuration, and plastic type was assessed through systematic experiments. Results showed that technical-grade PP, under optimal conditions, yielded up to 81.4 wt.% gas with a hydrogen concentration of 45.2 vol.% and a hydrogen efficiency of 44.8 g/g. In contrast, PE and mixed PP + PE waste displayed lower hydrogen performance, particularly when containing inorganic fillers. For all types of plastics studied, the gaseous fractions obtained have a high calorific value (46,941–55,087 kJ/kg) and at the same time low specific CO₂ emissions (4.4–6.1 × 10⁻⁵ kg CO₂/kJ), which makes these fuels very efficient and have a low carbon footprint. Comparative tests using conventional heating revealed significantly lower hydrogen yields (4.77 vs. 19.7 mmol/g plastic). These findings highlight the potential of microwave-assisted pyrolysis as an efficient method for transforming ELV-derived plastic waste into energy carriers, offering a pathway toward low-carbon, resource-efficient waste management. Full article

Traditional coal quality assessment methods rely exclusively on the laboratory testing of physical samples, which impedes detailed stratigraphic evaluation and limits the integration of intelligent precision mining technologies. To resolve this challenge, this study investigates geophysical logging as an innovative method for coal quality prediction. By integrating scanning electron microscopy (SEM), X-ray analysis, and optical microscopy with interdisciplinary methodologies spanning mathematics, mineralogy, and applied geophysics, this research analyzes the coal quality and mineral composition of the Shanxi Formation coal seams in northern Jiangsu, China. A predictive model linking geophysical logging responses to coal quality parameters was established to delineate relationships between subsurface geophysical data and material properties. The results demonstrate that the Shanxi Formation coals are gas coal (a medium-metamorphic bituminous subclass) characterized by low sulfur content, low ash yield, low fixed carbon, high volatile matter, and high calorific value. Mineralogical analysis identifies calcite, pyrite, and clay minerals as the dominant constituents. Pyrite occurs in diverse microscopic forms, including euhedral and semi-euhedral fine grains, fissure-filling aggregates, irregular blocky structures, framboidal clusters, and disseminated particles. Systematic relationships were observed between logging parameters and coal quality: moisture, ash content, and volatile matter exhibit an initial decrease, followed by an increase with rising apparent resistivity (LLD) and bulk density (DEN). Conversely, fixed carbon and calorific value display an inverse trend, peaking at intermediate LLD/DEN values before declining. Total sulfur increases with density up to a threshold before decreasing, while showing a concave upward relationship with resistivity. Negative correlations exist between moisture, fixed carbon, calorific value lateral resistivity (LLS), natural gamma (GR), short-spaced gamma-gamma (SSGG), and acoustic transit time (AC). In contrast, ash yield, volatile matter, and total sulfur correlate positively with these logging parameters. These trends are governed by coalification processes, lithotype composition, reservoir physical properties, and the types and mass fractions of minerals. Validation through independent two-sample t-tests confirms the feasibility of the neural network model for predicting coal quality parameters from geophysical logging data. The predictive model provides technical and theoretical support for advancing intelligent coal mining practices and optimizing efficiency in coal chemical industries, enabling real-time subsurface characterization to facilitate precision resource extraction. Full article

Introduction: The major cause of obesity is excessive calorie intake. Inappropriate dietary habits, like increased meal frequency, portion sizes, or amount of snacks consumed contribute to obesity development. Potential differences in the perception of snacks by people with different BMIs may be one of the causes of obesity. Assessment of the perception of snacks by people with excessive and normal body weight will allow us to check whether this parameter actually has an impact on the development of obesity. Materials and Methods: A survey study was conducted to check differences in assessing different snacks and beverages by individuals with varied BMIs. Participants analyzed snacks on presented photographs and assessed portion sizes, estimated caloric content, assessed whether the meal was healthy, and determined whether the indicated portion would be sufficient to satisfy their hunger. The study population was divided according to body mass index (BMI) into individuals with normal weight, overweight, and obesity. Additionally, the study group was divided according to gender and age. Results: There were no statistically significant differences in the majority of the studied parameters concerning BMI; however, the study revealed relatively low education level regarding caloric assessment. Conclusions: BMI seems not to have an influence on calorie and portion size perception of snacks. The majority of the population wrongly assessed the calorific value of snacks, which might contribute to obesity development. People have a tendency to overestimate the caloric value of snacks. Women assess the portion size of highly processed snacks as larger than men do. Full article

This study provides a comprehensive thermochemical characterization of common nut residues—almonds, walnuts, hazelnuts, peanuts, and pistachios shells—as potential biomass fuels, examining their chemical composition, calorific values, and emissions profiles. Their suitability as renewable energy sources was systematically assessed by verifying compliance with ISO 17225-2 standards for pellet production. The nut residues demonstrated promising energy characteristics, with higher heating values ranging from 17.75 to 19.12 MJ/kg and most samples fulfilling ISO 17225-2 classifications A1 or A2. Specifically, the walnut residues met the highest quality classification (A1), whereas the almond, hazelnut, and pistachio residues met the A2 classification, and the peanut residues were classified as B due to higher nitrogen content. A Life Cycle Assessment (LCA) was also performed to quantify the environmental impacts, focusing on CO₂ emissions from energy recovery and transportation. The results showed significantly lower CO₂ emissions from all the nut residues compared to fossil fuels such as coal, natural gas, fuel oil (HFO), and LPG. The almond residues exhibited the lowest total CO₂ emissions at 1669.27 kg CO₂ per ton, while the peanuts had the highest at 1945.93 kg CO₂ per ton. Even the highest-emitting nut residues produced substantially lower emissions compared to coal, which emitted approximately 4581.12 kg CO₂ per ton. These findings highlight the potential of nut residues as low-carbon, renewable energy sources, providing both environmental advantages and opportunities to support local agricultural economies. Full article

The Combined Cycle Combined Heat and Power (CCCHP) systems are an effective way to improve energy efficiency and reduce emissions. This paper examines the energy and environmental impact of CCCHP combustion using waste biomass like the biomass of spent wash (SW), waste crankcase oil (WCO), and bagasse (BA) using an advanced Ebsilon Professional 16 software simulation model. The simulations were designed to achieve 150 MW total power output and 25 MW heating energy. Simulation results indicate that the minimum fuel feed requirement of a 10.762 kg/s flow rate was recorded at the highest calorific value (CV) fuel briquette of 1:8 ratio BA–WCO. The BA–WCO system demonstrates a significantly higher heat recovery capacity in the heat recovery steam generator (HRSG) compared to the BA–SW system. At a 1:8 ratio, it recovers 1463 kJ/kg versus 583 kJ/kg, and 1391 kJ/kg versus 498 kJ/kg at a 1:3 ratio. The CCCHP efficiency was much higher for BA–WCO than those developed from spent wash–bagasse, yielding up to 41.1% compared to a maximum of 26.71%. Furthermore, the BA–WCO system showed a better result than the BA–SW CCCHP system by emitting a low amount of flue gas with low temperature. Full article

The accelerated urbanisation that is occurring in many regions of the world is resulting in a corresponding increase in the volume of sewage sludge. This sludge is then stored in specialised landfills, the area of which is increasing annually. One of the methods of utilising this sludge is through its combustion in power plants, where it serves to generate heat. However, due to the low calorific value of sewage sludge, it is recommended to combust it in conjunction with high-calorific fuel. To improve energy efficiency of sewage residue biomass utilisation by co-combustion with coal, it is necessary to determine the main combustion parameters and mass fraction in the mixture. The objective of this study is to estimate the primary parameters of combustion of sewage sludge and coal by employing the synchronous thermal analysis method, in addition to determining the concentrations of gaseous substances formed during the combustion process. A comprehensive technical and elemental analysis of the fuels was conducted, and their thermal properties were thoroughly determined. The inorganic residue from sewage sludge combustion was analysed by scanning electron microscopy for the content of trace elements and basic oxides. Thermogravimetric analysis (TGA) of fuels was conducted in an oxidising medium, utilising a 6 mg suspension with a heating rate of 20 °C/min. The profiles of TG, DTG, and DSC curves were then utilised to determine the ignition and burnout temperatures, maximum mass loss rate, combustion index, and synergistic effects. The mixture of coal with 25% sewage sludge was found to have the most energy-efficient performance compared to other mixtures, with a 3% reduction in ignition temperature compared to coal. Concentrations of carbon dioxide, carbon monoxide, nitrogen oxides, and sulphur oxides were also determined. Full article

The present study investigates the catalytic conversion of low-density polyethylene (LDPE) into high-grade fuel oil using a semi-batch reactor at 350 °C under ambient pressure, with a catalyst-to-LDPE ratio of 1:20. Zeolite-based catalysts were synthesized by impregnating different metals (Fe, Zn, Cr, Mn, and Ga) onto ZSM-5 with a silica-to-alumina ratio of 30 (Z30). These catalysts were characterized using BET, XRD, and NH3-TPD techniques to evaluate their physicochemical properties. The results showed that catalytic pyrolysis of LDPE yielded less pyrolytic oil compared to non-catalytic pyrolysis. The obtained pyrolytic oil was analysed through elemental composition, gross calorific value (GCV), Simulated Distillation, and GC-DHA. The elemental analysis revealed a high carbon (85–86%) and hydrogen (13–14%) content, resulting in a high GCV of approximately 42 MJ/kg. GC-DHA analysis indicated that the pyrolytic oil was rich in aromatic and olefinic compounds. Among the catalysts, 5Fe/Z30 exhibited the highest aromatic selectivity (35%), a research octane number of 91, and 100% LDPE conversion. These findings underscore the potential of low-cost iron-based catalysts for efficiently converting LDPE waste into valuable chemicals and fuels. Full article