Search Results (674)

Brine with a high magnesium-to-lithium ratio was separated by electrodialysis equipped with a monovalent cation exchange membrane under differing operational parameters. The ionic concentration variations, separation coefficients, lithium recovery ratio, permselectivity coefficient, and Li⁺ flux were analyzed to evaluate the effect of the initial Li⁺/Mg²⁺ mass concentration ratio, applied voltage, and initial volume ratio between the dilute and concentrated compartments on the separation performance of magnesium and lithium. The results showed that the increase in initial Li⁺/Mg²⁺ concentration ratio significantly increased the separation coefficient, lithium recovery ratio, and Li⁺ flux, demonstrating an improvement in the separation performance since the Li⁺ migration was accelerated when less Mg²⁺ competed with Li⁺. As the applied voltage increased from 10 V to 15 V, the separation coefficient increased, and the lithium recovery ratio and Li⁺ flux increased within 60 min; however, as the applied voltage increased to 20 V, the separation coefficient, the lithium recovery ratio, and the Li⁺ flux did not increase, which indicated that an increase in the applied voltage within the limits would contribute to the separation performance. The increase in the initial volume ratio between the dilute and concentrated compartments decreased the separation coefficient and lithium recovery ratio, indicating that the separation performance had declined. Full article

Oxygen transport membranes (OTMs) have gained a lot of attention for their application in different innovative fields, but the development of new materials able to combine high oxygen permeability and good chemical stability is crucial to boost the exploitation of such membrane-based technologies. Perovskite oxides are widely studied as mixed ionic-electronic conductors for the realization of OTMs. In this article, we focus on _Sr1-xCa_xTi_0.8Fe_0.2O_3-ẟ (SCTF) perovskites and investigate the effect of Ca content on the A-site of the permeation properties, both in single-phase SCTF membranes and in dual-phase membranes obtained by combining SCTF and the ionic conductor Ce_0.8Gd_0.2O₂ (CGO). In single-phase samples, we observed that the substitution of 40% Ca preserves the permeation performances of the non-substituted SrTi_0.8Fe_0.2O_3−ẟ membrane while allowing for a substantial decrease in the sintering temperature, thus facilitating membrane manufacturing. In dual-phase membranes, the increase in the Ca content in the perovskite causes an increase in grain size. The permeation is, at least partially, controlled by the kinetics of the surface exchange reactions. This limitation can be overcome by the addition of an activation layer; however, the permeance of activated CGO-SCTF membranes still remains lower compared to the single-phase parent perovskitic membranes. Full article

Against the challenge of extreme lead (Pb) contamination (>15,000 ppm) in industrial polluted soils, where conventional agents fail to disrupt stable Pb–soil complexes—this study extends our prior cadmium (Cd) remediation research to validate amino acid ionic liquids (AAILs) for highly recalcitrant metals. Fifteen AAILs were screened via batch washing, with [Met][NO₃] (methionine-based) demonstrating the highest Pb removal efficiency. Single-factor optimization revealed that under the conditions of 0.8 mol/L, 6:1 liquid–soil ratio, 60 min, 85.4% Pb was removed from severely contaminated soil by [Met][NO₃]. Kinetic analysis using four common models showed that the second-order kinetic equation provided the best fit, indicating that Pb removal was predominantly driven by chemical reactions such as complexation or ion exchange. After washing, the contents of various Pb species were significantly reduced, thereby mitigating environmental risks. Notably, no substantial changes in soil texture were observed. However, a marked increase in organic matter content was detected, accompanied by decreases in soil pH and mineral element concentrations. Analysis of soil mineral composition, functional groups, and chemical speciation revealed that [Met][NO₃] primarily facilitated Pb removal through ion-exchange and coordination reactions. This study establishes [Met][NO₃] as a green agent with dual efficacy: it achieves high-efficiency remediation of severely Pb-contaminated soil while ensuring environmental sustainability, thus highlighting its potential for practical application. Full article

Natural polymers, such as gelatin, offer a sustainable, green, and versatile alternative for developing proton exchange membranes in low-temperature fuel cell applications. They provide a balance of biocompatibility, flexibility, and ionic conductivity. In this work, gelatin-based composite membranes are reported. The membranes were fabricated and modified with various additives, including ionic liquids (ILs), polyethylene glycol (PEG), and glycerol, to enhance their electrochemical and mechanical properties. The proton conductivity of the pure gelatin membrane was relatively low at 1.0368 × 10⁻⁴ Scm⁻¹; however, the incorporation of IL ([DEMA][OMs]) significantly improved it, with the gelatin/0.2 g IL membrane achieving the highest conductivity of 4.181 × 10⁻⁴ Scm⁻¹. The introduction of PEG and glycerol also contributed to enhanced conductivity and flexibility. The water uptake analysis revealed that IL-containing membranes exhibited superior hydration properties, with the highest water uptake recorded for the gelatin/0.2 g glycerol/0.2 g IL membrane, which was found to be very high (906.55%). The results showed that the combination of IL and PEG provided enhanced proton transport and mechanical stability (as examined visually), making these membranes promising candidates for fuel cell applications. Therefore, this study underscores the importance of bio-based materials by utilizing gelatin as a sustainable, biodegradable polymer, supporting the transition toward greener energy materials. The findings demonstrate that modifying gelatin with conductivity-enhancing and plasticizing agents can significantly improve its performance, paving the way for bio-based proton exchange membranes with improved efficiency and durability. Full article

Samples of gel-type cation exchangers of the TOKEM nomenclature were tested for lithium extraction from multicomponent natural brines. The dependencies of the extraction of Li and other impurities—Na, Ca, and Mg—on the duration of the sorption process for the tested ion-exchange resins under static conditions are presented. Metal ions can be arranged according to the degree of extraction for each ion exchanger in a row: Ca²⁺ < Mg²⁺ < Li⁺, Na⁺. Testing of ion exchangers under static conditions on technological Li-containing solutions confirms the applicability of TOKEM-140 and TOKEM-160 cation exchangers for lithium extraction. For TOKEM-140, lithium extraction over time varies from 76.2% to 73.8% and for TOKEM-160—from 73.8% to 72.4%. The ionic background of natural brines has a significant effect on the capacity of ion exchangers for lithium and forms the following series Li⁺ << Mg²⁺ < Ca²⁺ << Na⁺ relative to the obtained concentrations of metal ions in natural brine. The overlay of IR spectra of TOKEM-140 and TOKEM-160 ion exchangers before and after saturation shows slight changes in their appearance, indicating that the lithium sorption process has occurred. The values of static exchange capacity (SEC) for TOKEM-140 and TOKEM-160 cation exchangers are identical. Full article

This study examines the effects of several commercial surfactants on the dispersion of catalyst inks for proton exchange membrane fuel cells (PEMFCs). Catalyst inks containing Pt/C were spray-coated and assembled into membrane electrode assemblies (MEAs) by hot pressing. The structural and electrochemical properties of the resulting catalyst layers were characterized through particle size analysis, zeta potential measurements, contact angle determinations, and single-cell performance tests. Among the formulations evaluated, the ink with non-ionic surfactant Triton X-100 (TX) delivered the best performance, achieving a current density of 1134 mA/cm² at 0.3 V—substantially higher than that of the surfactant-free control. These findings provide practical guidance for selecting appropriate surfactants to optimize catalyst-ink preparation and enhance PEMFC performance. Full article

Zeolites are widely used as adsorbents due to their porous structure and ion-exchange capabilities. However, their adsorption efficiency for heavy metal ions remains limited. To enhance their performance, the natural zeolite heulandite (Z) was functionalized with guanidine derivatives: N-[3-(triethoxysilyl)propyl]guanidine (1), -aminoguanidine (2), and -acetyl-guanidine (3). The resulting materials (Z1–Z3) were evaluated for their ability to adsorb Co²⁺, Cu²⁺, and Ni²⁺ from aqueous solutions. The composition and structure of silanes 1–3 were confirmed by FT-IR and ¹H and ¹³C NMR spectroscopy methods. The modified zeolites were characterized using nitrogen adsorption/desorption (BET) and SEM-EDX to confirm their functionalization and assess the structural changes. A TGA-DSC was used to determine the thermal stability. The adsorption experiments were conducted in single and multi-ionic aqueous solutions at pH 5.0 to evaluate metal uptake. Functionalization significantly improved the adsorption efficiency, with Z1–Z3 showing a three to six times greater adsorption capacity than the unmodified zeolite. The adsorption efficiency followed the trend Cu²⁺ > Co²⁺ > Ni²⁺, primarily due to chelate complex formation between the metal ions and guanidine groups. The SEM-EDX confirmed the co-localization of nitrogen atoms and metal ions. The functional materials (Z1–Z3) exhibited strong potential as adsorbents for noble, heavy, and toxic metal ions, and could find applications in industry, agriculture, ecology, medicine, chemistry, wastewater treatment, soil remediation, chemisorption, filtration, chromatography, etc. Full article

This study investigates key factors affecting the adsorption behavior of proteins on the multimodal chromatographic adsorbent Capto MMC, aiming to enhance selective protein separation strategies. Batch equilibrium experiments were conducted using six model proteins to explore the combined effects of pH, ionic strength, and the nature of salts (kosmotropic and chaotropic) on protein–ligand interactions. Given that the Capto MMC ligand supports multiple interaction modes beyond cation exchange, particular focus was placed on acidic proteins (pI 4–5), which exhibited binding even at moderately elevated pH values—conditions ineffective for conventional cation exchangers. Hydrophobic interactions were identified as critical for stable binding of proteins like BSA and fetuin, while hydrophilic proteins such as ovalbumin showed minimal adsorption. Chromatographic column experiments were performed to evaluate elution performance under various buffer conditions, revealing that prolonged adsorption phases can reduce recovery yields for proteins with less stable tertiary structures. The findings highlight how salt type, pH, and protein hydrophobicity interplay to modulate multimodal binding mechanisms, providing practical insights for the design of tailored purification protocols. Full article

The growing demand for ultra-low sulfur fuels has intensified interest in recovering strategic metals from the large volumes of hazardous hydrodesulfurization catalysts that are discarded yearly. This work evaluates a task-specific ionic liquid, tri-n-octylammonium bis(2-,4-,4-trimethylpentyl)-phosphinate [TOA][Cy272], synthesized by the acid–base neutralization of tri-n-octylamine and Cyanex 272. FT-IR spectroscopy confirmed complete proton transfer and the formation of a stable ion pair. Liquid–liquid extraction tests were conducted with synthetic Co–Ni–Mo solutions (0.1–2.5 g/L each), a varying ionic liquid concentration (10–50 vol%), pH (1.5–12.5), and organic/aqueous ratio (1:1). At 35 vol% of ionic liquid and pH 2, the extraction efficiency for Mo reached 94%, with separation factors βMo/Ni = 12 and βMo/Co = 7.5; Co and Ni uptake remained ≤15%. Selectivity decreased at higher metal loadings because of ionic liquid saturation, and an excessive ionic liquid amount (>35%) offered no benefit, owing to viscosity-limited mass transfer. Stripping studies showed that 1 M NH₄OH stripped about 95% Mo, while leaving Co and Ni in the organic phase; conversely, 2 M HCl removed 92–98% of Co and Ni, but <5% Mo. Overall Mo recovery of about 95% was obtained by a two-step extraction/stripping scheme. The results demonstrate that [TOA][Cy272] combines the cation exchange capability of quaternary ammonium ILs with the strong chelating affinity of organophosphinic acids, delivering rapid, selective, and regenerable separation of Mo from mixed-metal leachates and wastewater streams. Full article

Soil salinity and sodicity are escalating global threats to agricultural productivity, severely limiting crop yield and quality. In the Igdir Plain of Türkiye, high summer temperatures, minimal precipitation, and a shallow groundwater table have intensified salinity-related challenges, currently affecting one-third of the arable land. Despite the substantial impact of salinity stress on eggplant (Solanum melongena L.) production, studies addressing plant tolerance mechanisms under real field conditions remain limited. In this study, eggplant was cultivated in eight distinct soil classes under open-field conditions to evaluate the effects of soil salinity and saline-alkalinity on morphological, physiological, and biochemical traits. Increasing soil exchangeable sodium percentage (ESP) and electrical conductivity (ECe) levels significantly suppressed plant height, root length, stem diameter, and leaf area, along with over 90% reductions in shoot and root biomass. Salinity impaired the uptake of essential nutrients (Ca, K, P, and Fe), while promoting toxic Na⁺ accumulation in leaves. This ionic imbalance induced oxidative stress, as indicated by elevated malondialdehyde (MDA), hydrogen peroxide (H₂O₂), and antioxidant enzyme activities (SOD, CAT, APX), all of which were strongly correlated with proline accumulation. The results highlight a coordinated plant response under salinity stress but also reveal the insufficiency of natural defense mechanisms under high salinity levels. Unless supported by external interventions to improve stress resilience and ensure productivity, growing eggplant in saline–alkaline soils should be avoided. Full article

Ion-exchange membranes (IEMs) are widely used in reverse-electrodialysis (RED) technology, which can collect the salinity gradient energy between concentrated and diluted solutions and convert it into electromotive force (EMF) to drive power generation and hydrogen production. Recent studies have indicated that the permselectivity of IEMs is vital to determining the performance of an RED stack. In this study, the influences of solution concentration, ion species, and solution temperature on the permselectivity of IEMs were experimentally investigated. The results demonstrate that the permselectivity of IEMs decreases with increasing concentrations of KAc, LiCl, and LiBr solutions for both concentrated solutions (3–5 M) and dilute solutions (0.02–0.2 M). Further, through comparing the LiBr and KBr solutions as well as the LiCl, KCl, and NH₄Cl solutions, respectively, K⁺ demonstrates a higher permselectivity than Li⁺, and both of which are smaller than NH₄⁺ under the same cation and concentration conditions. Moreover, another test was conducted using three potassium salt solutions with different anions, and the experimental permselectivity order is Ac⁻ > Br⁻ > Cl⁻. A slight increase in solution temperature enhances the permselectivity of IEMs due to the increase in ionic mobility. However, an excessive temperature is detrimental to membrane stability and thus reduces permselectivity. It can be seen that ions with low hydration energy, a small hydration radius, and high mobility show a higher permselectivity. Full article

The thermo-chemical treatment of dental implants leads to the formation of sodium titanate crystals on their surface. When in contact with blood, these crystals dissolve and trigger an ionic exchange cascade, resulting in the formation of a calcium apatite layer. This study, carried out both in vitro and in an animal model, aimed to determine whether the cooling rate of the treatment affects the size of the deposited crystals, and whether this in turn influences wettability and early bone-to-implant contact (BIC). A total of 50 dental implants and 50 titanium discs were treated using four different cooling rates, along with a control group. Crystal size was analyzed on implant surfaces using scanning electron microscopy, and wettability was assessed on titanium discs using a goniometer. Finally, the implants were placed in the tibiae of 13 rabbits, and histological analysis was performed after three weeks to compare BIC among groups. Results suggest that a cooling rate of 75 °C/h produces smaller sodium titanate crystals, which are associated with significantly improved surface wettability and a higher percentage of bone-to-implant contact after 3 weeks of healing (p < 0.05). Full article

This study investigates the behavior of phosphate ion transport through two structurally distinct anion-exchange membranes—AMV (homogeneous) and HC-A (heterogeneous)—in an electrodialysis system under both static and stirred conditions at varying pH levels. Chronopotentiometric and current–voltage analyses were used to investigate the influence of pH and hydrodynamics on ion transport. Under underlimiting (ohmic) conditions, the AMV membrane exhibited simultaneous transport of H₂PO₄⁻ and HPO₄²⁻ ions at neutral and mildly alkaline pH, while such behavior was not verified at acidic pH and in all cases for the HC-A membrane. Under overlimiting current conditions, AMV favored electroconvection at low pH and exhibited significant water dissociation at high pH, leading to local pH shifts and chemical equilibrium displacement at the membrane–solution interface. In contrast, the HC-A membrane operated predominantly under strong electroconvective regimes, regardless of the pH value, without evidence of water dissociation or equilibrium change phenomena. Stirring significantly impacted the electrochemical responses: it altered the chronopotentiogram profiles through the emergence of intense oscillations in membrane potential drop at overlimiting currents and modified the current–voltage behavior by increasing the limiting current density, reducing electrical resistance, and compressing the plateau region that separates ohmic and overlimiting regimes. Additionally, both membranes showed signs of NH₃ formation at the anodic-side interface under pH 7–8, associated with increased electrical resistance. These findings reveal distinct ionic transport characteristics and hydrodynamic sensitivities of the membranes, thus providing valuable insights for optimizing phosphate recovery via electrodialysis. Full article

Oral delivery of hydrophobic compounds remains challenging due to their poor aqueous solubility and the potential toxicity associated with conventional surfactant-based emulsions. To address these issues, we present a surfactant-free encapsulation strategy using electrosprayed alginate hydrogel beads for the stable and controlled delivery of hydrophobic oils. Hydrophobic compounds were dispersed in high-viscosity alginate solutions without surfactants via ultrasonication, forming kinetically stable oil-in-water dispersions. These mixtures were electrosprayed into calcium chloride baths, yielding monodisperse hydrogel beads. Higher alginate concentrations improved droplet sphericity and suppressed phase separation by enhancing matrix viscosity. The resulting beads exhibited stimuli-responsive degradation and controlled release behavior in response to physiological ionic strength. Dense alginate networks delayed ion exchange and prolonged structural integrity, while elevated external ionic conditions triggered rapid disintegration and immediate payload release. This simple and scalable system offers a biocompatible platform for the oral delivery of lipophilic active compounds without the need for surfactants or complex fabrication steps. Full article

This paper presents information on ionic liquids (ILs) and explores their potential applications in heat exchange systems. Basic information on ionic liquids and their selected thermophysical properties is presented in a manner that facilitates their use in future research. The physical properties of IL that are important in the area of heat exchange are described in detail, with particular emphasis on heat exchange in flow. Issues related to the melting point, specific heat, thermal conductivity coefficient, and viscosity of selected ionic liquids, as well as the effect of temperature on their changes, are discussed. The physical properties of IL are compared with the physical properties of water treated in heat exchange as a reference substance. The issues of creating aqueous solutions of ionic liquids and the effect of the amount of water on the physical properties of the resulting solution are discussed. It is demonstrated that selected ionic liquids can be considered an alternative to traditional working liquids commonly used in heat exchange systems. Full article