Search Results (168)

Lime plaster has historically been a key material in the preservation of architectural heritage in Peru; however, its availability has been restricted by state regulations that limit its production and commercialization. This study evaluates the performance of paints formulated with inorganic pigments extracted from soils in the Cusco valley, combined with natural and synthetic binders, as a sustainable alternative for the protection of heritage buildings in this Andean region characterized by high altitude, wide thermal variations, and high solar radiation. Adhesion, hardness, drying time, and weather resistance tests were conducted according to applicable ASTM standards for architectural coatings. The results show that these formulations exhibit good adhesion to historic surfaces and greater durability against extreme environmental conditions compared to traditional lime plaster. Their potential compatibility with historic substrates and lower environmental impact suggest that these paints represent a viable alternative in sustainable conservation strategies; however, further studies are needed to more accurately characterize the mineralogical composition of the pigments used. Full article

Selenium (Se), as a vital trace element, plays an important role in regulating the antioxidant systems of plants, strengthening photosynthetic capacity, and enhancing their stress resistance. Selenate and selenite are the dominant forms of Se available to plants in soils. This research takes highland barley as the research object, aiming to assess the impacts of plant growth, organic acid metabolite, and six transcription factor families in highland barley seedlings under varying concentrations of Na₂SeO₃. The study indicated that compared to the control group (CK), the plant height of highland barley seedlings under Se1 (0.02 g/kg Na₂SeO₃) treatment significantly increased by 66%. Under the Se2 (0.2 g/kg Na₂SeO₃) treatment, plant height significantly decreased by 28%. With Na₂SeO₃ concentration increased, the pigment content, O₂⁻ production rate, and soluble protein content in highland barley seedlings decreased, while the contents of soluble sugar, MDA, and H₂O₂ increased. Se1 treatment was found to be more beneficial for the growth and development of seedlings. The organic selenium in leaves and roots under Se2 treatment significantly increased by 1105-fold and 188-fold, respectively. The most effective migration capability from soil to leaf under Se1 or Se2 treatment was up to 6.15 or 6.56, respectively. Based on metabolomics, 30 differential metabolites of organic acids were screened from highland barley seedlings under Na₂SeO₃ treatment and showed positive correlationships with organic selenium, inorganic selenium, and total selenium in highland barley seedling leaves. Through transcriptome analysis, heatmap analysis on six major categories of transcription factors (bHLH, MYB, NAC, WRKY, GATA, and HSF) was performed. Under Se2 treatment, approximately two-thirds of the transcription factors showed high expressions. We further screened 26 differentially expressed genes (DEGs) related to Na₂SeO₃ concentration. Based on correlation analysis, there were six genes in the bHLH family, five in MYB, three in NAC, five in WRKY, and three in the GATA and HSF families that showed positive correlations with 30 differential organic acid metabolites. These results enhance our understanding of the relationship between the organic acid metabolites and transcription factor expression in highland barley seedlings under Na₂SeO₃ treatment. Full article

Stormwater runoff is a significant source of microplastics to surface water. This study addresses challenges in the sampling, treatment, and characterization of microplastics in existing stormwater control measures across various regions in the United States. Stormwater sediment samples were collected via traditional stormwater sampling approaches for particulate and inorganic contamination with portable automatic samplers, analyzed using visible and fluorescence microscopy with Nile red as a selective stain, and subsequently confirmed through Raman spectroscopy. The inclusion of laboratory and field blanks enabled the identification of contamination at key steps during sample handling. The results reveal that the filtration process is a significant source of laboratory contamination, while the sampling process itself could be a primary contributor to overall sample contamination. Additionally, it was found that using green fluorescence as the sole emission wavelength may underestimate MP quantities, as some particles emit fluorescence exclusively in the red spectrum. Raman analysis revealed interferences caused by pigments and additives in plastics, along with challenges evaluating particles in the low micron range (≤10 microns), which complicates a comprehensive analysis. The findings of this study emphasize the importance of implementing strong quality assurance and control measures when assessing the levels of microplastics in the environment, including sample collection, processing, and analysis. Full article

As a core structure within the Qing Changling Mausoleum, a UNESCO World Cultural Heritage site, Long’en Hall preserves a relatively complete set of Qing dynasty imperial lacquered furniture. These furnishings provide critical physical evidence for studying Qing dynasty sacrificial rituals and the craftsmanship of court lacquerware. However, limited research has been conducted on the surface finishing techniques of such furnishings, posing challenges to their conservation and accurate restoration. This study focuses on representative furnishings from Long’en Hall—including an offering table, an incense pavilion, a throne, and a poke lamp—and employed a multi-method analytical approach comprising fluorescence microscopy (FM), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS), X-ray photoelectron spectroscopy (XPS), and Fourier-transform infrared (FTIR) spectroscopy. The analysis was conducted on the following two levels: the lacquer layer structure and material composition. The results show that the furnishings in the Long’en Hall adopt the typical structure of “lacquer ash layer–color lacquer layer”, and the color lacquer layer is composed of raw lacquer, tung oil, animal glue, and other natural organic ingredients as film-forming materials, supplemented with inorganic mineral pigments such as red lead (Pb₃O₄) and Au metal, which constitutes a stable organic–inorganic composite structure with the lacquer ash layer. The multi-analysis results show a good complementary and cross-corroboration relationship, providing the necessary technical support and a theoretical reference for Qing dynasty palace lacquer wood furniture as cultural relics worthy of scientific protection and imitation. Full article

The influence of structural water in alumina (Al₂O₃) and silica (SiO₂) coated titanium dioxide (TiO₂) pigments on the photodegradation behavior of polypropylene (PP) composites was investigated. Four commercial rutile TiO₂ pigments with varying surface inorganic coatings were incorporated into PP plaques and subjected to accelerated UV weathering to simulate outdoor exposure. Photodegradation was assessed through gloss retention measurements, the carbonyl index (CI), and stress at break retention, while pigment morphology and composition were analyzed using transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS). Surface charge and water content were determined through the zeta potential (ζ), Karl Fischer titration, thermogravimetric analysis (TGA), and Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS). The results showed that low-alumina coating alone led to the lowest photodegradation resistance, the highest CI, and the lowest stress at break retention. In contrast, increasing alumina content enhanced photostability, reaching its maximum for combined alumina–silica coatings, which mitigated electron–hole pair migration. PP composites with high alumina–silica-coated TiO₂ exhibited higher gloss retention (36%) compared to low-alumina samples (21%). Furthermore, statistical analysis using ANOVA revealed significant differences in coating content and ζ potential among the pigment grades. These findings provide novel insights into oxide-water interactions and the impact of structural water on the photodegradation of polymer composites. Full article

Biodegradable mulch films were developed over the last decades to replace polyethylene, but their short durability and higher costs still limit their diffusion. This work aimed to test an innovative composite mulching film constituted by a mixture of carboxylmethyl cellulose, chitosan and sodium alginate, enriched or not with an inorganic N- and P-source to help the microbial breakdown in soil. The trial was carried out using outdoor mesocosms cultivated with lettuce plants with high-density planting. Commercial Mater-Bi^® and a polyethylene film were taken as control treatments. Air temperature and humidity monitored daily during the 51 d cropping cycle remained within the ideal range for lettuce growth with no mildew or fungi infection. Visible mechanical degradation of the experimental biopolymers occurred after 3 weeks; however, Mater-Bi^® and polyethylene remained unaltered until harvest. Chemical soil variables (TOC, TN, CEC, EC) remained unchanged in all theses, whereas the pH varied. The yield, pigments, total phenols, flavonoids and ROS scavenging activity of lettuce were similar among treatments. Despite their shorter life service (~3 weeks), polysaccharide-based mulching films showed their potential to protect lettuce plants at an early stage and provide yield and nutraceutical values similar to conventionally mulched plants, while allowing a reduced environmental impact and disposal operations. Full article

The artisanal production of paints using inorganic pigments from the Cusco Valley is considered a sustainable alternative to the use of synthetic industrial paints. This approach not only helps reduce the environmental footprint associated with the use of volatile organic compounds (VOCs) but also utilizes local materials. The present study evaluates the physical and mechanical properties of paints obtained from natural pigments through standardized tests based on the American ASTM standards, focusing on adhesion (ASTM D-3359), drying time (ASTM D-1640), surface hardness (ASTM D-3363), and the performance of the paints when exposed to the environmental factors of Cusco (under real conditions). In this regard, the pigments were extracted from traditional quarries and processed through the sedimentation method (MS) and ball milling (MG). The produced paints were formulated with the addition of polyvinyl acetate (PVA) as a binder and water as a solvent and were applied to standardized panels. The results show that all samples meet the requirements of the technical parameters, demonstrating good adhesion, appropriate drying times, and acceptable hardness for architectural coatings, Chromatic variations (ΔE*) were recorded depending on the processing method and the level of environmental exposure, with paints containing ground pigments (MG) being more resistant to fading. This study concludes that these artisanal formulations represent a technically viable and culturally relevant alternative to industrial coatings, especially in contexts of heritage restoration or sustainable architecture. Full article

This communication presents an approach to the chromatic study of rock painting scenes in the Tecsecocha sector, Ccorca district, Cusco, Peru, through the application of color spectrophotometry using Capsure by XRite, considered a portable device that facilitates reference measurements of color codes belonging to the visible spectrum (400–700 nm). It is evident that this methodology does not perform the physicochemical characterization of the pigments present in the rock paintings, which are cataloged as artistic heritage of the nation, making it unfeasible to extract physical samples or significantly alter the rock paintings. Therefore, the NCS color notation system allowed for the non-invasive recording of color tones. The results showed a predominance of white and red tones with variations in their shades; among the most frequent codes, S2030-Y70R and S3010-Y40R stand out, indicating yellow tones with red influences of 70% and 40%, respectively. In the anthropomorphic figures, a slight variation in the proportion of red was identified, suggesting differences in the application of pigments, while in the representations of camelids, the tones varied from S3005-Y20R (yellow with 20% red) to S2030-Y70R (greater red influence). Full article

Modern and contemporary artworks, due to technological developments in the synthesis of new pigments, are characterized by a pictorial palette composed of a wide variety of pigments. This diversity makes it increasingly important to carry out thorough characterization studies in order to gain a complete and comprehensive understanding of the properties of the numerous pigments in use today. In this work, 18 modern acrylic paints were characterized using micro-Raman spectroscopy with two laser excitation lines (532 nm and 633 nm). The analysed pigments can be classified as organic, inorganic, or mixtures, depending on their chemical composition. Specifically, the following pigments were investigated: Cobalt Blue, Permanent Blue Light, Ultramarine, Primary—Cyan Blue, Cerulean Blue, Cobalt Blue (Hue), Indanthrene Blue, Phthalo Blue, Van Dyke Brown, Permanent Green Light, Phthalo Green, Primary Red—Magenta, Cadmium Red Medium, Lemon Yellow, Cadmium Yellow Medium, Zinc White, Titanium White and Iridescent Silver. The pigments were applied to wooden and glass substrates to simulate the creative processes of actual modern and contemporary artworks. The aim was to define their composition, as this knowledge is essential for the protection, conservation and enhancement of cultural heritage. Full article

Curtobacterium species are increasingly recognized as plant pathogens and soil decomposers, but their prevalence and function as plant endophytes in aerial organs are less clear. In this study, we isolated six endophytic Curtobacterium species from the fruits, flower petals (previously unreported) and stem tissue of plants from diverse environments and examined their general characteristics. We found that all Curtobacterium endophytes belonging to three major Curtobacterium clusters—C. oceanosedimentum (a group not previously recognized as endophytic), C. luteum and C. flaccumfaciens—shared some common features. All or nearly all isolates tested were pigmented, displayed moderate salt tolerance and, surprisingly, were psychrotolerant, being able to grow at 6 °C. The exception was a fruit C. luteum isolate that appears to have evolved thermotolerance (up to 45 °C) instead as a likely adaptation to its environment. All isolates were able to metabolize starch and casein and solubilize inorganic phosphate, indicating conserved secreted hydrolase activity, but only isolates in the C. oceanosedimentum group were able to absorb and metabolize citrate. Finally, all endophytes tested were able to ferment the plant sugars sucrose and fructose, while they differed in their ability to use other sugars. Thus, this study documents common traits and adaptations in various Curtobacterium endophytes, and the presence of these isolates in floral and fruit organs implies the possible seed-borne inheritance of these isolates. Full article

Iron redox cycling in paddy soils drives the release and mineralisation of dissolved organic carbon (DOC), influencing the emission of CO₂ and CH₄. Light irradiation exerts an inhibitory effect on the mineralisation of soil organic carbon, but the responses to light intensity of iron redox processes coupled with organic carbon transformation and greenhouse gas emissions remain underexplored. Here, we conducted a slurry incubation experiment with paddy soil at varying light intensities. The dynamics of soil ferrous iron [Fe(II)], DOC, dissolved inorganic carbon (DIC), and chlorophyll a, as well as headspace CO₂ and CH₄, were monitored over a 40-day period. The results demonstrated that light irradiation inhibited iron reduction, leading to a 58.1–74.7% decrease in soil Fe(II) concentration compared to dark incubation. The oxidation of Fe(II) generated from iron reduction was enhanced under light incubation (3.12–3.53 mg g⁻¹), and the oxidation rate constant trended higher with increasing light intensity. Light irradiation reduced CO₂ and CH₄ emissions to 8.8–76.9% and 2.3–6.7% of those under dark incubation, respectively. With the extension of incubation time, soil DIC concentration showed an increase followed by a decrease under light incubation, and the earlier DIC decrease occurred at higher light intensities. The DOC decrease rate constant was greater under light incubation (0.024–0.042 d⁻¹) than under dark incubation (0.012 d⁻¹). Light irradiation activated phototrophic microorganisms producing chlorophyll a (4.71–6.46 mg g⁻¹), whereas this pigment was undetectable under dark incubation. Organic carbon mineralisation was positively correlated with Fe(II) concentration, and Fe(II) oxidation was positively correlated with chlorophyll a concentration and DOC decrease (p < 0.05). Agricultural practices optimizing light exposure, such as shallow flooding or reducing plant density, are promising approaches to bolster DOC sequestration and mitigate CO₂ and CH₄ emissions in paddy fields. Full article

The increasing use of nanostructured silver-containing inorganic materials raises concerns about their impact on aquatic organisms. This study assessed the toxicity of silver-modified bentonite composites on Chlamydomonas sp. Two materials were tested: silver-exchanged bentonite (Ben-Ag) and its reduced form (Ben-Ag (H₂)).Microalgae were exposed to 0.5 IC₅₀, 1.5 IC₅₀, and 2 IC₅₀. Ben-Ag showed higher toxicity than Ben-Ag (H₂), which even promoted algal growth at low doses. Fluorescence microscopy revealed morphological shrinkage in treated cells. Increased phenol content, elevated malondialdehyde (MDA) levels, and altered antioxidant enzyme activities further confirmed Ben-Ag toxicity, along with reduced growth and photosynthetic pigments. Transcriptomic analysis revealed significant changes in gene expression under Ben-Ag exposure. Genes involved in photosynthesis (petB, psbL), caspase activity (casp), and carotenoid metabolism (Q2CHY) were down-regulated, indicating stress-induced damage. In contrast, genes encoding stress response enzymes (SOD, peroxidase), carbon metabolism enzymes (rbcL, PGQ1), and β-carotene biosynthesis (Q2BKT) were up-regulated, reflecting cellular defense mechanisms. Overall, the study highlights the high toxicity of Ben-Ag to Chlamydomonas sp., emphasizing the importance of evaluating environmental risks before using such materials in aquatic environments. Full article

TiO₂ nanoparticles are found as pigments in coatings and paints and are, therefore, released into the environment through runoff. To assess their environmental impact, comprehensive fate and ecotoxicity studies necessitate particles closely resembling those released into the environment. In response, we developed a method designed to isolate TiO₂ particles from commercial paints. Using six contrasting paints alongside a pure TiO₂ pigment, we evaluated two extraction methods in terms of recovery, purification rate, and preservation of both inorganic and organic particle coatings. The paints and extracts were characterized using cryogenic-TEM, ICP-OES, thermogravimetry, and infrared spectroscopy. In contrast to the alkaline-based extraction method, the extraction with acetic acid facilitated the retention of both inorganic and organic coatings and ensured good removal of organic polymers. Recovery rates exceeded 70% for all paints and extraction methods, yet the complete removal of SiO₂, when present, was not achieved. CaCO₃ removal was effective with both extraction methods. Our developed extraction method enables the isolation of TiO₂-particles similar to those aged within paints. However, we recommend using silicate-free paints when SiO₂ interference is of concern for the study design. Furthermore, this method could be interesting for pigment recycling, offering a gentler alternative to existing techniques which compromise particle coatings. Full article

Paint loss is one of the main forms of deterioration in historical wall paintings, generally restored by the application of chromatic reintegration. In the specific case of outdoor exposed paintings, it is essential to find a binder that will withstand diverse weather conditions. Since chromatic reintegrations have to be compatible with the original painting, fresco paint mock-ups were manufactured and compared to chromatic reintegrations made with an aqueous colloidal dispersion of silica nanoparticles as binder. The physical compatibility was studied by colour spectrophotometry and measurements of static contact angle, gloss, and roughness values, together with a peeling test, stereomicroscopy, and polarised light microscopy. They were also characterised from a mineralogical, chemical, and molecular point of view using X-ray diffraction, X-ray fluorescence and Fourier-transform infrared spectroscopy. The microtexture was studied by scanning electron microscopy with energy-dispersive X-ray spectroscopy. Chromatic reintegrations showed similar roughness and lower gloss values than frescoes, and the nano-silica binder ensured the natural breathability of the wall. Overall, the chemical nature of pigments was highly influential. The reintegrations with silicate-based pigments were more homogenous, with hardly any fissures, while those carried out with sulphide- or oxide-based pigments were severely cracked. The use of verdigris is discouraged due to the lack of affinity between the binder and the pigment. Full article

This study aims to explore the feasibility of producing submicrometer and nanometer cellulose fibers derived from rice husk treated with a novel method which selectively eliminate hemicellulose and lignin, while maintaining the integrity of the cellulosic and silica constituents. Three distinct processing methods are tested to extract the nanocellulose, namely hand milling, ball milling, and wet milling using a high-shear wet media mill from Masuko Sangyo Co., Ltd., Kawaguchi-city, Japan. A range of analytical methods, including Scanning Electron Microscopy (SEM), Energy-Dispersive X-ray Spectroscopy (EDX), Transmission Electron Microscopy (TEM), Fourier Transform Infrared Spectroscopy (FTIR), Differential Scanning Calorimetry (DSC), and Thermogravimetric Analysis (TGA), are utilized to characterize the morphology, elemental composition, thermal stability, and chemical properties of the samples. The study revealed that among the tested methods, only wet milling successfully produced cellulose nanofibrils and silica nanoparticles, forming a biogenic organic–inorganic nanohybrid system. The nanofibers had lengths in the range of 120 nm and below, while the nanoparticles were in the tens of nanometers. The silica nanoparticles were found to adhere to the cellulose nanofibrils, forming a biogenic organic–inorganic nanohybrid system, with potential applications across diverse fields, including biomedical (drug delivery, biosensing, bone regeneration, and wound healing), cosmetic (skin and dental care), technical (insulating aerogels, flame retardants, and UV-absorbing pigments), and food applications (dietary supplements, thickeners). Full article