Search Results (284)

Zoological environments aim to promote natural behaviours and optimal welfare conditions. Over the past decade, research on the use of artificial ultraviolet-B (UV-B) exposure has improved vitamin D₃ levels and reduced incidences of metabolic bone disease in diurnal primates; however, this has not been investigated in nocturnals. Aye-ayes (Daubentonia madagascariensis), nocturnal lemurs often housed indoors in zoos with little to no exposure to natural sunlight, have been reported to have low vitamin D₃ levels. This study aims to investigate the impacts of artificial UV-B as a supplemental healthcare strategy for aye-ayes, examining its influences on vitamin D₃ levels and positional sleeping behaviour. The 25-hydroxy-vitamin D₃ (25OHD₃) blood levels were tested before and after exposure to different levels of artificial UV-B and heat sources. Statistical analysis showed no correlation between UV-B and 25OHD₃ at group parameter levels. However, one individual showed a positive correlation. Sleeping position duration analysis showed a potential basking behaviour with the use of increased ear exposure and other thermoregulatory responses. Despite representing 8.06% of the European captive aye-aye population, these findings highlight the need for further research on vitamin D₃ parameters and responses to UV-B to optimise captive conditions and support the species’ long-term health. Full article

High nighttime temperature (HNT) due to asymmetric diurnal warming threatens wheat productivity. This study evaluated the effect of HNT on wheat phenology, physiology, and yield through field and controlled environment experiments in Central Queensland, Australia. Two wheat genotypes, Faraday and AVT#6, were assessed under three sowing dates—1 May (Early), 15 June (Mid), and 1 August (Late)—within the recommended sowing window for the region. In a parallel growth chamber study, the plants were exposed to two nighttime temperature regimes, of 15 °C (normal) and 20 °C (high), with consistent daytime conditions from booting to maturity. Late sowing resulted in shortened vegetative growth and grain filling periods and increased exposure to HNT during the reproductive phase. This resulted in elevated floret sterility, lower grain weight, and up to 40% yield loss. AVT#6 exhibited greater sensitivity to HNT despite maturing earlier. Leaf gas exchange analysis revealed increased nighttime respiration (Rn) and reduced assimilation (A), resulting in higher Rn/A ratio for late-sown crops. The results from controlled environment chambers resembled trends of the field experiment, producing lower grain yield and biomass under HNT. Cumulative nighttime hours above 20 °C correlated more strongly with yield losses than daytime heat. These findings highlight the need for HNT-tolerant genotypes and optimized sowing schedules under future climate scenarios. Full article

Photovoltaic–thermal (PVT) technology has attracted considerable attention for its ability to significantly improve solar energy conversion efficiency by simultaneously providing electricity and heat during the day. PVT technology serves a purpose in condensers and subcoolers for passive cooling in refrigeration systems at night. In our previous work, we proposed a switchable film-insulated photovoltaic–thermal–passive cooling (PVT-PC) module to address the structural incompatibility between diurnal and nocturnal modes. However, the performance of the proposed module strongly depends on two key design parameters: the structural height and the vacuum level of the air cushion. In this study, a numerical model of the proposed module is developed to examine the impact of design and meteorological parameters on its all-day performance. The results show that diurnal performance remains stable across different structural heights, while nocturnal passive cooling power shows strong dependence on vacuum level and structural height, achieving up to 103.73 W/m² at 10 mm height and 1500 Pa vacuum, which is comparable to unglazed PVT modules. Convective heat transfer enhancement, induced by changes in air cushion shape, is identified as the primary contributor to improved nocturnal cooling performance. Wind speed has minimal impact on electrical output but significantly enhances thermal efficiency and nocturnal convective cooling power, with a passive cooling power increase of up to 31.61%. In contrast, higher sky temperatures degrade nocturnal cooling performance due to diminished radiative exchange, despite improving diurnal thermal efficiency. These findings provide fundamental insights for optimizing the structural design and operational strategies of PVT-PC systems under varying environmental conditions. Full article

This study examines diurnal surface temperature dynamics across major Moroccan cities during the growing season and explores the interaction between urban and vegetated surfaces. We also introduce the Urban Thermal Impact Ratio (UTIR), a novel metric designed to quantify urban thermal comfort as a function of the surface urban heat island (SUHI) intensity. The analysis is based on outputs from a land surface model (LSM) for the year 2010, integrating high-resolution Landsat and MODIS data to characterize land cover and biophysical parameters across twelve land cover types. Our findings reveal moderate urban–vegetation temperature differences in coastal cities like Tangier (1.8 °C) and Rabat (1.0 °C), where winter vegetation remains active. In inland areas, urban morphology plays a more dominant role: Fes, with a 20% impervious surface area (ISA), exhibits a smaller SUHI than Meknes (5% ISA), due to higher urban heating in the latter. The Atlantic desert city of Dakhla shows a distinct pattern, with a nighttime SUHI of 2.1 °C and a daytime urban cooling of −0.7 °C, driven by irrigated parks and lawns enhancing evapotranspiration and shading. At the regional scale, summer UTIR values remain below one in Tangier-Tetouan-Al Hoceima, Rabat-Sale-Kenitra, and Casablanca-Settat, suggesting that urban conditions generally stay within thermal comfort thresholds. In contrast, higher UTIR values in Marrakech-Safi, Beni Mellal-Khénifra, and Guelmim-Oued Noun indicate elevated heat discomfort. At the city scale, the UTIR in Tangier, Rabat, and Casablanca demonstrates a clear diurnal pattern: it emerges around 11:00 a.m., peaks at 1:00 p.m., and fades by 3:00 p.m. This study highlights the critical role of vegetation in regulating urban surface temperatures and modulating urban–rural thermal contrasts. The UTIR provides a practical, scalable indicator of urban heat stress, particularly valuable in data-scarce settings. These findings carry significant implications for climate-resilient urban planning, optimized energy use, and the design of public health early warning systems in the context of climate change. Full article

Ravine forests are key to conserving biodiversity and maintaining ecosystem processes in fragmented landscapes. Here, we evaluated the phenology of plant species in the Los Nogales Nature Sanctuary (Lo Barnechea, Chile) using Sentinel-2 images (2019–2024) and the Alos Palsar DEM (12.5 m). We calculated the Normalized Difference Vegetation Index (NDVI), the Topographic Position Index (TPI), and Diurnal Anisotropic Heat (DAH) to assess vegetation dynamics across different topographic and thermal gradients. Generalized Additive Models (GAM) revealed that tree species exhibited more stable, regular seasonal NDVI trajectories, while shrubs showed moderate fluctuations, and herbaceous species displayed high interannual variability, likely reflecting sensitivity to climatic events. Spatial analysis indicated that trees predominated on steep slopes and higher elevations, herbs were concentrated in low-lying, moisture-retaining areas, and shrubs were more common in areas with higher thermal load. These findings highlight the significant role of terrain and temperature in shaping plant phenology and distribution, underscoring the utility of remote sensing and topographic indices for monitoring ecological processes in complex mountainous environments. Full article

The occurrence of haze pollution significantly deteriorates air quality and threatens human health, yet persistent knowledge gaps in real-time source apportionment of fine particulate matter (PM_2.5) hinder sustained improvements in atmospheric pollution conditions. Thus, this study employed single-particle aerosol mass spectrometry (SPAMS) to investigate PM_2.5 sources and dynamics during winter haze episodes in Yinchuan, Northwest China. Results showed that the average PM_2.5 concentration was 57 μg·m⁻³, peaking at 218 μg·m⁻³. PM_2.5 was dominated by organic carbon (OC, 17.3%), mixed carbonaceous particles (ECOC, 17.0%), and elemental carbon (EC, 14.3%). The primary sources were coal combustion (26.4%), fugitive dust (25.8%), and vehicle emissions (19.1%). Residential coal burning dominated coal emissions (80.9%), highlighting inefficient decentralized heating. Source contributions showed distinct diurnal patterns: coal combustion peaked nocturnally (29.3% at 09:00) due to heating and inversions, fugitive dust rose at night (28.6% at 19:00) from construction and low winds, and vehicle emissions aligned with traffic (17.5% at 07:00). Haze episodes were driven by synergistic increases in local coal (+4.0%), dust (+2.7%), and vehicle (+2.1%) emissions, compounded by regional transport (10.1–36.7%) of aged particles from northwestern zones. Fugitive dust correlated with sulfur dioxide (SO₂) and ozone (O₃) (p < 0.01), suggesting roles as carriers and reactive interfaces. Findings confirm local emission dominance with spatiotemporal heterogeneity and regional transport influence. SPAMS effectively resolved short-term pollution dynamics, providing critical insights for targeted air quality management in arid regions. Full article

The Marine Atmospheric Boundary Layer (MABL), as a critical component of Earth’s climate system, governs the exchange of matter and energy between the ocean surface and the lower atmosphere. This study presents shipborne Doppler lidar observations conducted during 12 January to 3 February 2024, along the southeastern Chinese coast. Employing a Coherent Doppler Wind Lidar (CDWL) system onboard the R/V “Yuezhanyu” research vessel, we investigated the spatiotemporal variability of MABL characteristics through integration with ERA5 reanalysis data. The key findings reveal a significant positive correlation between MABL height and surface sensible heat flux in winter, underscoring the dominant role of sensible heat flux in boundary layer development. Through the Empirical Orthogonal Function (EOF) analysis of the ERA5 regional boundary layer height, sensible heat flux, and sea level pressure, we demonstrate MABL height over the coastal seas typically exceeds the corresponding terrestrial atmospheric boundary layer height and exhibits weak diurnal variation. The CDWL observations highlight complex wind field dynamics influenced by synoptic conditions and maritime zones. Compared to onshore regions, the MABL over offshore areas further away from land has lower wind shear changes and a more uniform wind field. Notably, the terrain of Taiwan, China, induces significant low-level jet formations within the MABL. Low-level jets and low boundary layer height promote the pollution episode observed by CDWL. This research provides new insights into MABL dynamics over East Asian marginal seas, with implications for improving boundary layer parameterization in regional climate models and advancing our understanding of coastal meteorological processes. Full article

This study evaluated the effects of photovoltaic (PV) arrays on critical surface parameters through analysis of observational data collected from a utility-scale PV power station located in Wujiaqu City, Xinjiang, in 2021. The results reveal that: (1) Installation of PV panels reduces surface albedo, which is significantly altered by dust storm conditions; (2) the installation of PV arrays increases the aerodynamic and thermal roughness length by increasing the frictional velocity across the mixed underlying surface; (3) the overall transport coefficients within the PV plant are higher than that of the reference site, with greater diurnal variation than nocturnal variation. The overall transport coefficient is highest in the unstable stratification conditions and lowest under stable stratification conditions; and (4) soil thermal property parameters exhibit seasonal variations. Significant changes in thermal conductivity and specific heat capacity were observed during spring thaw, high and fluctuating diffusivity in summer, and low and stable values in winter. The findings demonstrate that installing PV arrays in arid regions modifies surface energy balance and heat transfer characteristics. This provides a basis for optimizing PV station layouts and conducting climate impact assessments. Full article

Environmental impacts, such as elevated temperatures due to urban heat islands (UHIs), associated with land cover change due to urbanization, should not be ignored. In contrast to conventional impermeable concrete, permeable pavements have been implemented as green infrastructure strategies for achieving environmental benefits, such as stormwater management. Their impacts and benefits on other environmental aspects should not be ignored, especially for those with limited discussion in the literature. Therefore, this study monitored the surface and air temperatures of three types of pavements: conventional impermeable concrete (IC), pervious concrete (PC), and the patented JW Eco-technology (JW). As UHIs are more intense in the summer, temperature profiles during targeted periods when surface temperatures exceeded 40 °C for consecutive days were examined. In addition, as an available option at the study site, shade was created to evaluate its effect on surface temperatures across the pavement systems. Overall, the annual average surface and air temperatures of the three pavements were similar. However, seasonal and diurnal variations in temperatures were both observed, suggesting summer was the season when the differences in temperatures among pavements were most noticeable. Investigation during the targeted periods revealed that the average surface temperatures of PC were 2.4–2.7 °C and 3.2–3.3 °C higher than those observed on IC and JW, and the average air temperature of PC was 1.8 °C greater than that of IC and JW between 12:00 and 16:00. On the contrary, the average surface temperatures of PC were significantly lower than those on IC (1.3–1.4 °C) and JW (1.5 °C) between 21:00 and 5:00. Results also indicate that shade was an effective way to alleviate the high surface temperatures during the warm hours by lowering surface temperatures 21.0 °C, 15.4 °C, and 15.0 °C, for PC, IC, and JW, respectively. Finally, temperatures associated with the aqueducts of JW Eco-technology and the impacts on overall surface temperatures will be discussed. Full article

Global warming has intensified the frequency and intensity of heatwaves, particularly in urban areas, significantly affecting residents’ daily activities. Extant studies have mainly concentrated on the relationship between socio-economic attributes and the impacts of heatwaves on urban populations. However, the relationship between the built environment and the impacts of heatwaves on urban population distribution has not received much attention. Furthermore, most studies have overlooked the temporal heterogeneity in heatwave impacts on population activities and distribution. Therefore, taking the central urban area of Nanchang as the case, this study investigated the impacts of heatwaves on population distribution and their temporal heterogeneity. Moreover, it identified the nonlinear relationships between built environment factors and population changes during heatwaves by using the XGBoost model and SHAP method. The results revealed that heatwaves exerted the largest impacts on population distribution during weekend nights, followed by weekend daytime and weekday nighttime, with the least impacts observed during weekday daytime. Furthermore, location and transportation factors significantly affected population changes during heatwaves across most time periods, with their influences being associated with policy factors such as the high-temperature leave policy for workers in industrial zones located in urban fringe areas and the cooling zone establishment policy for citizens in subway stations. Moreover, land use and building form factors exhibited significant temporal heterogeneity in their impacts on population changes during heatwaves. This temporal heterogeneity was fundamentally driven by individuals’ heat adaptation behaviors, the spatiotemporal patterns of their daily activities, and the diurnal variations in the built environment’s influence on local thermal environment. These findings provide valuable insights to proactively alleviate the adverse impacts of heatwaves. Full article

A simple statistical model capturing the degree to which different patterns of urban development intensify urban heat islands (UHIs) and stress human health would be useful but has remained elusive. Accurately predicting street-level urban air temperatures from land cover and thermal data is difficult due to (1) the coarse scale of common remote sensing data, which do not observe the key environments beneath urban tree canopies, and, (2) conversely, the immense labor of intense, location-specific, ground-based survey campaigns. This work tested whether remotely sensed urban heat merged with land cover heterogeneity and shade/sun fractions, if combined at a sufficiently fine scale so as to be linearly additive, would enable simple and accurate statistical modeling of street-scale urban air temperatures with minimal empirical fitting. We used ground-based thermography of a sample of 12 residential streetscapes in Portland, Oregon, to characterize the land surface temperatures (LST_g) of eleven common urban surface cover types when sun-exposed and in shade. Surfaces were cooler in shade than sun, but with surface-specific differences not explained by greenery nor (im)perviousness. Also, surfaces on streetscapes with more canopy cover, even when sun-exposed at midday, remained significantly cooler than comparable sun-exposed surfaces on streets with less canopy cover, indicating the key significance of partial diurnal shading, not typically accounted for in urban thermal statistical models. We used high-resolution orthoimagery to quantify the area of each surface cover type within each streetscape and computed an area-weighted average surface temperature (T_s), accounting for sun/shade heterogeneity. The data revealed a significant, nearly 1:1 relationship between calculated T_s values and sun-shielded air temperatures (T_a). In contrast, relationships of T_a to tree coverage, impervious area, or the LST_g of dominant surface cover types were all statistically insignificant. These results suggest that statistical models may more reliably bridge the gap between remote sensing urban surface temperatures and reliable predictions of street-scale air temperatures if (1) analysis is at a sufficiently high resolution (e.g., <10 m) to avoid some of the known scale-dependence of urban thermal environments and enable simple weighted linear models, and (2) distinctions between thermal contributions of sunlit and shaded surfaces are included along with the influence of diurnal shading. Such models may provide effective and low-cost predictions of local UHIs and help inform effective street-level approaches to mitigating urban heat. Full article

Utilizing 58 Landsat-7 images taken over 10 years, the current study investigated the relationship between the mitigation of surface urban heat islands (SUHIs) by NbSs (Nature-based Solutions) and influential variables such as physical variables of NbSs, environmental variables of the streets, and meteorological variables. Parks and permeable pavements are the two types of NbS devices under examination. Reference (i.e., unaffected by any NbS) and experimental (i.e., affected by only one NbS) areas were selected to perform the analysis. Areas affected by large water bodies or more than one NbS device were excluded. The cooling effect caused by NbS was linked to the influential variables by multiple regression models. Key findings included the following: Firstly, the distance to an NbS is more important than the area of an individual NbS, implying that small and evenly distributed NbS devices might have better overall cooling effects than large but sparsely placed NbS devices. Secondly, NbSs do not significantly contribute to cooling in districts with grid-type streets, while exhibiting significant cooling for districts with complex street patterns. Older districts with complex street patterns should be the focus of NbS implementation, not newer, modern districts. However, NbS cooling is sensitive to several variables in districts with complex patterns. NbS installation in those districts requires careful planning to maximize engineering investment. Lastly, maintenance can be essential to sustain the cooling capacity of NbSs over time. Full article

This study investigates the relationship between Green View Index (GVI) and street thermal environment in Hangzhou’s main urban area during summer, quantifying urban greenery’s impact on diurnal/nocturnal thermal conditions to inform urban heat island mitigation strategies. Multi-source data (3D morphological metrics, LCZ classifications, mobile measurements) were integrated with deep learning-derived street-level GVI through image analysis. A random forest-multiple regression hybrid model evaluated spatiotemporal variations and GVI impacts across time, street orientation, and urban-rural gradients. Key findings include: (1) Urban street Ta prediction model: Daytime model: R² = 0.54, RMSE = 0.33 °C; Nighttime model: R² = 0.71, RMSE = 0.42 °C. (2) GVI shows significant inverse association with temperature, A 0.1 unit increase in GVI reduced temperatures by 0.124°C during the day and 0.020 °C at night. (3) Orientation effects: North–south streets exhibit strongest cooling (1.85 °C daytime reduction), followed by east–west; northeast–southwest layouts show negligible impact; (4) Canyon geometry: Low-aspect canyons (H/W < 1) enhance cooling efficiency, while high-aspect canyons (H/W > 2) retain nocturnal heat despite daytime cooling; (5) Urban-rural gradient: Cooling peaks in urban-fringe zones (10–15 km daytime, 15–20 km nighttime), contrasting with persistent nocturnal warmth in urban cores (0–5 km); (6) LCZ variability: Daytime cooling intensity peaks in LCZ3, nighttime in LCZ6. These findings offer scientific evidence and empirical support for urban thermal environment optimization strategies in urban planning and landscape design. We recommend dynamic coupling of street orientation, three-dimensional morphological characteristics, and vegetation configuration parameters to formulate differentiated thermal environment design guidelines, enabling precise alignment between mitigation measures and spatial context-specific features. Full article

Accurate evapotranspiration (ET) monitoring is important for making scientific irrigation decisions. Unmanned aerial vehicle (UAV) remote sensing platforms allow for the flexible and efficient acquisition of field data, providing a valuable approach for large-scale ET monitoring. This study aims to enhance the accuracy and reliability of ET estimation in rice paddies through two synergistic approaches: (1) integrating the energy flux diurnal variations into the Two-Source Energy Balance (TSEB) model, which considers the canopy and soil temperature components separately, for physical estimation and (2) optimizing the flight altitudes and observation times for thermal infrared (TIR) data acquisition to enhance the data quality. The results indicated that the energy flux in rice paddies followed a single-peak diurnal pattern dominated by net radiation (Rn). The diurnal variation in the ratio of soil heat flux (G) to Rn could be well fitted by the cosine function with a max value and peak time (R² > 0.90). The optimal flight altitude and time (50 m and 11:00 am) for improved identification of temperature differentiation between treatments were further obtained through cross-comparison. These adaptations enabled the TSEB model to achieve a satisfactory accuracy in estimating energy flux compared to the single-source SEBAL model, with R² values of 0.8501 for Rn − G and 0.7503 for latent heat (LE), as well as reduced rRMSE values. In conclusion, this study presents a reliable method for paddy field scale ET estimation based on a calibrated TSEB model. Moreover, the integration of ground and UAV multimodal data highlights its potential for precise irrigation practices and sustainable water resource management. Full article

The eddy dissipation rate (EDR, or turbulence dissipation rate) is a crucial parameter in the study of the atmospheric boundary layer (ABL). However, the existing Doppler lidar-based estimates of EDR seldom offer long-term comparisons that span the entire ABL. Building upon prior research utilizing Doppler lidar wind-field data, we optimized the EDR retrieval algorithm using a genetic adaptive approach. The newly developed algorithm demonstrates enhanced accuracy in EDR estimation. The daily evolution of EDR reveals a distinct diurnal pattern in its variation. A detailed four consecutive days study of turbulence generated via low-level jets (LLJs) indicated that EDR driven by heat flux (~10⁻² m²/s³) is significantly stronger than that produced through wind shear (~10⁻³ m²/s³). Subsequently, we examined seasonal variations in EDR at different mixing layer heights (MLH, Zi): elevated EDR values in summer (~7 × 10⁻³ m²/s³ at 0.1Zi) contrasted with reduced levels in winter (~6 × 10⁻⁴ m²/s³ at 0.1Zi). In the early morning, EDR decreases with height for 1 magnitude, while in later stages, it remains relatively stable within 0.1 order of magnitude across 0.1Zi to 0.9Zi. Notably, the EDR during DJF exceeds that of MAM and SON in the afternoon. This suggests that ML turbulence is not solely dependent on surface fluxes (SHF + LHF) but may also be influenced by MLH. A lower MLH (smaller volume), even with reduced surface fluxes, could potentially result in a stronger EDR. Finally, we compared the evolution of the EDR and MLH in the boundary layer using Doppler lidar data from ARM sites and the PBL (Planetary Boundary Layer) Moving Active Profiling System (PBLMAPS) Airborne Doppler Lidar (ADL). The results show that the vertical wind data exhibit strong consistency (R = 0.96) when the ADL is positioned near ARM Southern Great Plains (SGP) sites C1 or E37. The ADL’s mobility and flexibility provide significant advantages for future field experiments, particularly in challenging environments such as mountainous or complex terrains. This study not only highlights the potential of utilizing Doppler lidar alone for EDR calculations but also extensively explores the development patterns of EDR within the ABL. Full article