Search Results (1,514)

Ultrahigh-temperature ceramic composites based on hafnium diboride have a wide range of applications, including as components for high-speed aircraft and energy generation and storage devices. Consequently, developing methodologies for their fabrication and studying their properties are of paramount importance, in particular in using them as an electrode material for energy storage devices with increased oxidation resistance. This study investigates the behavior of ceramic composites based on the HfB₂-HfO₂-SiC system, obtained using 15 vol% Ti₂AlC MAX-phase as a sintering component, under the influence of subsonic flow of dissociated air. It was determined that incorporating the modifying component (Ti₂AlC) altered the composition of the silicate melt formed on the surface during ceramic oxidation. This modification led to the observation of a protective antioxidant function. Consequently, liquation was observed in the silicate melt layer, resulting in the formation of spherical phase inhomogeneities in its volume with increased content of titanium, aluminum, and hafnium. It is hypothesized that the increase in the high-temperature viscosity of this melt prevents it from being carried away in the form of drops, even at a surface temperature of ~1900–2000 °C. Despite the established temperature, there is no sharp increase in its values above 2400–2500 °C. This is due to the evaporation of silicate melt from the surface. In addition, the electrochemical behavior of the obtained material in a liquid electrolyte medium (KOH, 3 mol/L) was examined, and it was shown that according to the value of electrical conductivity and specific capacitance, it is a promising electrode material for supercapacitors. Full article

Lithium lanthanum titanate (LLTO) is a promising solid electrolyte for all-solid-state lithium-ion batteries (ASSLIBs), and its total conductivity is dramatically influenced by the ceramic microstructure. Here we report a novel aerodynamic levitation rapid solidification method to prepare dense LLTO ceramics with a dendrite-like microstructure, which can be hardly obtained by conventional sintering. At optimal nominal lithium content and cooling rate, the solidified LLTO ceramic achieved a high total conductivity of 2.5 × 10⁻⁴ S·cm⁻¹ at room temperature, along with excellent mechanical properties such as a high Young’s modulus of 240 GPa and a high hardness of 16.7 GPa. Results from this work suggest that aerodynamic levitation rapid solidification is an effective processing method to manipulate the microstructure of LLTO ceramics to minimize the GBs’ contribution to the total conductivity, which may be expanded to prepare other oxide-type lithium electrolytes. Full article

This study demonstrates the successful fabrication of high-performance reaction-bonded silicon carbide (RBSC) ceramics through an optimized liquid silicon infiltration (LSI) process employing multi-modal SiC particle gradation and nano-carbon black (0.6 µm) additives. By engineering porous preforms with hierarchical SiC distributions and tailored carbon sources, the resulting ceramics achieved a compressive strength of 2393 MPa and a flexural strength of 380 MPa, surpassing conventional RBSC systems. Microstructural analyses revealed homogeneous β-SiC formation and crack deflection mechanisms as key contributors to mechanical enhancement. Ultrafine SiC particles (0.5–2 µm) refined pore architectures and mediated capillary dynamics during infiltration, enabling nanoscale dispersion of residual silicon phases and minimizing interfacial defects. Compared to coarse-grained counterparts, the ultrafine SiC system exhibited a 23% increase in compressive strength, attributed to reduced sintering defects and enhanced load transfer efficiency. This work establishes a scalable strategy for designing RBSC ceramics for extreme mechanical environments, bridging material innovation with applications in high-stress structural components. Full article

Textured Si₃N₄/BN composite ceramics were successfully fabricated using two-step sintering, combining pseudo-hot isostatic pressing (PHIP) and gas pressure sintering. The grain size of h-BN platelets had a significant influence on densification and mechanical and thermal properties. With an increase in h-BN grain size, the volume density of the composite ceramics gradually decreased, while flexural strength gradually increased. Meanwhile, larger h-BN platelets were more likely to trigger toughening mechanisms like large-angle deflection and greatly increase fracture toughness. Through proper selection of h-BN grain size, textured ceramics, with the addition of h-BN platelets of 1–2 μm, showed high thermal conductivity (∼92 W∙m⁻¹∙K⁻¹) and reliable mechanical properties (∼540 MPa, ∼7.5 MPa∙m^1/2, ∼11.1 GPa). Therefore, texture control is an effective means of improving the overall performance of ceramic materials. Novel textured composite ceramics thus have great potential in large-scale fabrication and directional heat dissipation applications. Full article

Porous ceramics have been widely used in various fields. In this paper, porous ceramics with through-hole structures were prepared using a novel and eco-friendly gel casting method with carrageenan as the gelling agent. Especially, the idea of large size particle stacking is introduced into the gel casting process. By introducing large size alumina aggregates as raw materials, and small size micropowders as filling materials, micropores were directly formed after the green body was sintered. To tune the pore size, pore structure, gas permeability, the strength of the final porous ceramics, the components of the raw materials including the alumina aggregates, the filling materials, and sintering additives in the slurry were precisely designed. Porous Al₂O₃-based ceramics with high gas permeability, high flexural strength, and moderate porosity were finally obtained. Full article

To address the poor thermal shock resistance and high brittleness of traditional ceramic tools, a novel Si₃N₄/Sc₂W₃O₁₂ (SNS) composite ceramic material was developed via in situ synthesis using WO₃ and Sc₂O₃ as precursors and consolidated by spark plasma sintering. Sc₂W₃O₁₂ with negative thermal expansion was introduced to compensate for matrix shrinkage and modulate interfacial stress. The effects of varying Sc₂W₃O₁₂ content on thermal expansion, residual stress, microstructure, and mechanical properties were systematically investigated. Among the compositions, SNS3 (12 wt.% Sc₂W₃O₁₂) exhibited the best overall performance: relative density of 98.8 ± 0.2%, flexural strength of 712.4 ± 30 MPa, fracture toughness of 7.5 ± 0.3 MPa·m^1/2, Vickers hardness of 16.3 ± 0.3 GPa, and an average thermal expansion coefficient of 2.81 × 10⁻⁶·K⁻¹. The formation of a spherical chain-like Sc-W-O phase at the grain boundaries created a “hard core–soft shell” interface that enhanced crack resistance and stress buffering. Cutting tests showed that the SNS3 tool reduced workpiece surface roughness by 32.91% and achieved a cutting distance of 9500 m. These results validate the potential of this novel multiphase ceramic system as a promising candidate for high-performance and thermally stable ceramic cutting tools. Full article

The sustainable valorization of electrolytic manganese residue (EMR) and fly ash (FA) presents critical environmental challenges. This study systematically investigates the performance optimization of EMR-FA ceramic composites through the coordinated regulation of raw material ratios, sintering temperatures, and additive effects. While the composite with 85 g FA exhibits the highest mechanical strength, lowest porosity, and minimal water absorption, the formulation consisting of 45 wt% EMR, 40 wt% FA, and 15 wt% kaolin is identified as a balanced composition that achieves an effective compromise between mechanical performance and solid waste utilization efficiency. Sintering temperature studies revealed temperature-dependent property enhancement, with controlled sintering at 1150 °C preventing the over-firing phenomena observed at 1200 °C while promoting phase evolution. XRD-SEM analyses confirmed accelerated anorthite formation and the morphological transformations of FA spherical particles under thermal activation. Additive engineering demonstrated that 8 wt% CaO addition enhanced structural densification through hydrogrossular crystallization, whereas Na₂SiO₃ induced sodium-rich calcium silicate phases that suppressed anorthite development. Contrastingly, ZrO₂ facilitated zircon nucleation, while TiO₂ enabled progressive performance enhancement through amorphous phase modification. This work establishes fundamental phase–structure–property relationships and provides actionable engineering parameters for sustainable ceramic production from industrial solid wastes. Full article

A ceramic–metal composite was synthesized using sol–gel and electrospinning methods to serve as a SERS substrate. The precursors used were tetraethyl orthosilicate, aluminum nitrate, and zirconium, and polyvinylpyrrolidone was added to electrospun nonwoven fibrous membranes. The membranes were sintered, decorated with silver nanoparticles. The enhancement substrates were made of fibers of cylindric morphology with an average diameter of approximately 190 nm, a smooth surface, and 9 nm spherical particles decorating the surface of the fibers. The enhancement capacity of the substrates was tested using pyridine, methyl orange, methylene blue, crystal violet, and Eriochrome black T at different concentrations with Raman spectroscopy to determine whether the size and complexity of the analyte has an impact on the enhancement capacity. Enhancement factors of 2.53 × 10², 3.06 × 10¹, 2.97 × 10³, 4.66 × 10³, and 1.45 × 10³ times were obtained for the signal of pyridine, methyl orange, methylene blue, crystal violet, and Eriochrome black T at concentrations of 1 nM. Full article

The improvement of densification and fracture toughness in high-entropy ceramics is important to realizing their practical applications. In this study, SiC whiskers and metal Ni additions were incorporated to solve these problems of high-entropy boride ceramics. The influence of sintering temperatures (1450–1650 °C) on the densification, microstructure, hardness, fracture toughness, and bending strength of (M_0.2Ti_0.2Ta_0.2V_0.2Nb_0.2)B₂-SiC_w-Ni (M=Hf, Zr, or Cr) composites prepared by hot-pressing technology were studied. Results showed that when SiC whiskers and metal Ni additions were used as additives, increasing sintering temperatures from 1450 to 1600 °C promoted the densification of high-entropy boride ceramics. This was mainly attributed to the high sintering driving force. However, when the temperature further increased to 1650 °C, their densification behavior decreased. At a sintering temperature of 1600 °C, these high-entropy borides ceramics all had the highest densification behavior, leading to their high hardness and fracture toughness. The highest relative density was 96.3%, the highest hardness was 22.02 GPa, and the highest fracture toughness was 13.25 MPa·m^1/2, which was improved by the co-function of SiC whiskers and plastic metal Ni. Meanwhile, in the adopted sintering temperature range of 1450 to 1650 °C, the highest bending strength at room temperature of these high-entropy boride ceramics could reach 320.8 MPa. Therefore, this research offers an effective densification, strengthening, and toughening method for high-entropy boride composites at a low sintering temperature. Full article

The sustainable utilization of solid waste is crucial for environmental protection. This work investigates the fabrication of foamed ceramics from Cr slag and municipal solid waste incineration (MSWI) fly ash, focusing on the effects of three inhibitors—NH₂SO₃H, ZnO·TiO₂, and (NH₄)₂HPO₄—on material properties and Cr leaching behavior. Experimental analysis, chemical thermodynamic calculations, and material characterization were all employed. Results show that the prepared foamed ceramics meet the JG/T 511-2017 standard for building materials, exhibiting excellent physical properties but significant Cr leaching. Among the inhibitors, (NH₄)₂HPO₄ with a molar ratio of n(P)/n(Cr) = 1 shows the best performance, achieving a bulk density of 205 kg/m³, compressive strength of 0.850 MPa, Cr leaching concentration of 188 μg/L, and a 70.0% of Cr leaching inhibition rate. The improvement is attributed to the AlPO₄ formation that enhancing the strength, and Ca₂P₂O₇ that stabilizing Cr during sintering. This work provides a feasible method for the safe resource utilization of Cr-containing waste. Full article

To elucidate the key material parameters governing the tribological performance of ceramic composites under dry sliding against steel, this study presents a comprehensive comparative assessment of the microstructural characteristics, mechanical performance, and tribological behavior of two alumina–zirconia (Al₂O₃–ZrO₂) ceramic composites, each reinforced with a 42 vol.% carbide phase: zirconium carbide (ZrC) and tungsten carbide (WC). Specifically, tungsten carbide (WC) was selected for its exceptional bulk mechanical properties, while zirconium carbide (ZrC) was chosen to contrast its potentially different interfacial reactivity against a steel counterface. ZrC and WC were selected as reinforcing phases due to their high hardness and distinct chemical and interfacial properties, which were expected to critically affect the wear and friction behavior of the composites under demanding conditions. Specimens were consolidated via spark plasma sintering (SPS). The investigation encompassed macro- and nanoscale hardness measurements (Vickers hardness HV₁, HV₁₀; nanoindentation hardness H), elastic modulus (E), fracture toughness (K_IC), coefficient of friction (COF), and specific wear rate (W_s) under unlubricated reciprocating sliding against 100Cr6 steel at normal loads of 10 N and 25 N. The Al₂O₃–ZrO₂–WC composite exhibited an ultrafine-grained microstructure and markedly enhanced mechanical properties (HV₁₀ ≈ 20.9 GPa; H ≈ 33.6 GPa; K_IC ≈ 4.7 MPa·m^½) relative to the coarse-grained Al₂O₃–ZrO₂–ZrC counterpart (HV₁₀ ≈ 16.6 GPa; H ≈ 27.0 GPa; K_IC ≈ 3.2 MPa·m^½). Paradoxically, the ZrC-reinforced composite demonstrated superior tribological performance, with a low and load-independent specific wear rate (W_s ≈ 1.2 × 10⁻⁹ mm³/Nm) and a stable steady-state COF of approximately 0.46. Conversely, the WC-reinforced system exhibited significantly elevated wear volumes—particularly under the 25 N regime—and a higher, more fluctuating COF. Scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM–EDX) of the wear tracks revealed the formation of a continuous, iron-enriched tribofilm on the ZrC composite, derived from counterface material transfer, whereas the WC composite surface displayed only sparse tribofilm development. These findings underscore that, in steel-paired tribological applications of Al₂O₃–ZrO₂–based composites, the efficacy of interfacial tribolayer generation can supersede intrinsic bulk mechanical attributes as the dominant factor governing wear resistance. Full article

Ceramic dental prosthetics with internal metal structures are made from a cobalt–chromium alloy that is coated with ceramic. This study aims to validate surface treatments for the metal that enhance the adhesion of the ceramic coating under masticatory forces. Surface conditioning is performed using mechanical methods, like sandblasting (SB), and thermal methods, such as oxidation (O). The ceramic coating is applied to the metal component following the conditioning process, which can be conducted using either a single method or a combination of methods. Each conditioned sample undergoes characterization through various techniques, including drop shape analysis (DSA), scanning electron microscopy (SEM), X-ray diffraction (EDX), and atomic force microscopy (AFM). After the ceramic coating is applied and subjected to thermal sintering, the metal–ceramic samples are mechanically tested to assess the adhesion of the ceramic layer. The research findings, illustrated by scanning electron microscopy (SEM) images of the metal structures’ surfaces, indicate that alloy powder particles ranging from 10 to 50 µm were either adhered to the surfaces or present as discrete dots. Particles that exceed the initial design specifications of the structure can be smoothed out using sandblasting or mechanical finishing techniques. The energy-dispersive spectroscopy (EDS) results show that, after sandblasting, fragments of aluminum oxide remain trapped on the surface of the metal structures. These remnants are considered impurities, which can negatively impact the adhesion of the ceramic to the metal substrate. The analysis focuses on the exfoliation of the ceramic material from the deformed metal surfaces. The results emphasize the significant role of the sandblasting method and the micro-topography it creates, as well as the importance of the oxidation temperature in the treatment process. Drawing on 25 years of experience in dental prosthetics and the findings from this study, this publication aims to serve as a guide for applying the ceramic bonding layer to metal surfaces and for conditioning methods. These practices are essential for enhancing the adhesion of ceramic materials to metal substrates. Full article

Nowadays, there is wide advocacy for a transition to circular economic models. Fly Ash (FA) in particular is a major by-product of coal combustion and its annual waste has reached one million tonnes. Cenospheres (CSs) are considered as possibly the most valuable element within FA. Thus, in this research, polymeric foam replication was employed to fabricate ceramic foams based on a CS matrix, for potential biomedical applications. For the fabrication of foams, four types of natural marine sponges were used as templates along with a binder agent. The specimens were sintered at 1200 °C for 1 h. The results were encouraging as the specimens obtained retained the given shape and geometry. Further research will enhance the potential of such materials for future use in biomedical engineering. Full article

Lead-free (Bi_1/2Na_1/2)(Ti_1−x(Mg_1/3Nb_2/3)_x)O₃ ceramics were synthesized using the solid-phase method, and the effects of varying (Mg_1/3Nb_2/3)⁴⁺ content, substituting for Ti⁴⁺ ions at the B-site of the BNT perovskite lattice, on piezoelectric performance were systematically investigated. The influence of sintering temperature on both piezoelectric and ferroelectric properties was also explored, revealing that sintering temperature significantly affects both the microstructure and the electrical properties of the ceramics. The results indicate that the incorporation of (Mg_1/3Nb_2/3)⁴⁺ significantly enhances the piezoelectric and ferroelectric properties of BNT ceramics. Specifically, a maximum piezoelectric constant of 91 pC/N was achieved at a sintering temperature of 1160 °C and a doping concentration of x = 0.01. By comparing the ferroelectric properties across different doping levels and sintering temperatures, this study provides valuable insights for further design and process optimization of BNT-based piezoelectric materials. Full article

In this investigation, TiB₂–TiC composite powders, synthesized via the boron/carbon thermal reduction process, were employed as precursor materials. SiC, serving as the tertiary constituent, was incorporated to fabricate TiB₂–TiC–SiC composite ceramics utilizing spark plasma sintering technology. The present study initially elucidates the densification mechanisms and investigates the influence of sintering temperature on the densification behavior, microstructural evolution, and mechanical properties of the resultant ceramics. The experimental findings reveal that the sintering process of TiB₂–TiC–SiC ceramics exhibits characteristics consistent with solid-phase sintering. As the sintering temperature escalates, both the relative density and mechanical properties of the ceramics initially improve, reaching a maximum at an optimal sintering temperature of 1900 °C, before subsequently declining. Microstructural examinations conducted at this optimal temperature indicate a homogeneous distribution of the two primary phases, with no evidence of excessive grain growth. Furthermore, this research explores the effects of SiC addition on the mechanical performance and oxidation resistance of TiB₂–TiC–SiC composite ceramics. The results demonstrate that the incorporation of SiC effectively suppresses grain growth and promotes the formation of rod-like TiB₂ microstructures, thereby enhancing the mechanical attributes of the ceramics. Additionally, the addition of SiC significantly improves the oxidation resistance of the composite ceramics compared to their TiB₂–TiC binary counterparts Full article