Search Results (46)

Soil strengthening with hydraulic binders has gained popularity in recent years and provides an alternative to traditional methods, both for foundation reinforcement and for retaining walls. In many cases, columns, walls, or soil-cement mix blocks require reinforcement with steel sections. Correctly assessing the load-bearing capacity of a reinforced element requires an understanding of the bonding forces between the steel and the soil-cement mix. This article presents the results of pull-out tests conducted on steel flat bars embedded in a soil-cement mix. A soil-cement mix containing sand, silt, and clay fractions was prepared. The surfaces of the flat bars were treated in three different ways, and their roughness was subsequently measured. The pull-out strength of steel flat bars embedded in a soil-cement mix with compressive strength in the range of 1–2 MPa was determined. The tests revealed a correlation between surface roughness and bond strength. The conducted tests provided the basis for developing new research directions and for formulating a new bonding model for the interaction between steel profiles and soil-cement. Full article

This study aims to develop environmentally friendly soil-stabilization materials by investigating the synergistic enhancement mechanism of industrial by-product lignin fibers (LFs) and sodium sulfate (Na₂SO₄) on the mechanical and micro-structural properties of cement-stabilized soil. A systematic evaluation was conducted through unconfined compressive strength (UCS), splitting tensile strength, and capillary water absorption tests, supplemented by microscopic analyses including XRD and SEM. The results indicate that the optimal synergistic effect occurs at 1.0% LF and 0.10% Na₂SO₄, which increases UCS and splitting tensile strength by 9.23% and 18.37%, respectively, compared to cement-stabilized soil. Meanwhile, early strength development is accelerated. Microscopically, LF physically bridges soil particles, forming aggregates, reducing porosity, and enhancing cohesion. Chemically, Na₂SO₄ acts as an activator, accelerating cement hydration and stimulating pozzolanic reactions to form calcium aluminosilicate hydrate and gypsum, which fill pores and densify the matrix. The synergistic mechanism lies in Na₂SO₄ enhancing the interaction between the LFs and clay minerals through ion exchange, facilitating the formation of a stable spatial network structure that inhibits particle sliding and crack propagation. This technology offers substantial sustainability benefits by utilizing paper-making waste LF and low-cost Na₂SO₄ to improve soil strength, toughness, and impermeability. Full article

As an industrial waste, slag powder can be processed and incorporated into cement-based materials as an additive, significantly improving the engineering properties of cement–soil. The strength of slag–cement-stabilized soil is subject to nonlinear interactions among multiple factors, including cement content, slag powder dosage, curing age, and moisture content, forming a complex influence mechanism. To achieve accurate strength prediction and mix proportion optimization for slag–cement-stabilized soil, this study prepared cement-stabilized soil specimens with different slag powder contents using typical sandy soil and clay from the Nantong region, and obtained sample data through unconfined compressive strength tests. A Back Propagation (BP) neural network prediction model was also established. Addressing the limitations of traditional BP neural networks in prediction accuracy caused by random initial weight thresholds and susceptibility to local optima, the sparrow search algorithm (SSA) was introduced to optimize initial network parameters, constructing an SSA-BP model that effectively enhances convergence speed and generalization capability. Research results demonstrated that the SSA-BP model reduced prediction error by 53.4% compared with the traditional BP model, showing superior prediction accuracy and effective characterization of multifactor nonlinear relationships. This study provides theoretical support and an efficient prediction tool for industrial waste recycling and environmentally friendly solidified soil engineering design. Full article

High-plasticity clay soils pose significant challenges in geotechnical engineering due to their poor mechanical properties, such as low strength and high compressibility. Lime–cement stabilization offers a sustainable solution, but optimizing additive proportions requires advanced analytical approaches to decipher complex soil-stabilizer interactions. This study investigates the stabilization of high-plasticity clay soil (CH) sourced from Kano, Nigeria, using lime (0–30%) and cement (0–8%) for thirty (30) sample combinations to optimize consolidation and strength properties. Geotechnical laboratory tests (consolidation and UCS) were evaluated per ASTM standards. Multivariate analysis integrated principal component analysis (PCA) with regression modeling (PCR) for sensitivity and causality assessment. Optimal stabilization (15% lime + 6% cement) significantly improved soil properties: void ratio reduced by 58% (0.60→0.25), porosity by 49.5% (0.38→0.19), UCS increased by 222.5% to 2670 kPa (28 days), preconsolidation stress by 206% (355.63→1088.92 kPa), and compressibility modulus by 16% (7048→10,474.28 kPa). PCR sensitivity analysis attributed 46% of UCS variance to PC1 (compressibility parameters: void ratio, porosity, compression index; β = 0.72). PCR Causality analysis shows improvment with curing (R²: 68.7% at 7 days→83.0% at 28 days; RMSE: 11.2→7.8 kPa). PCR establishes compressibility reduction as the dominant causal mechanism for strength gain, providing a robust framework for dosage optimization beyond empirical approaches. Full article

This study presents the development and characterization of sustainable bio-bricks incorporating agricultural residues—specifically coffee husks and bovine excreta—as partial substitutes for cement. A mixture design optimized through response surface methodology (RSM) identified the best-performing formulation, namely 960 g of cement, 225 g of lignin (extracted from coffee husks), and 315 g of bovine excreta. Experimental evaluations included compressive and flexural strength, water absorption, density, thermal conductivity, transmittance, admittance, and acoustic transmission loss. The optimal mixture achieved a compressive strength of 1.70 MPa and a flexural strength of 0.56 MPa, meeting Colombian technical standards for non-structural masonry. Its thermal conductivity (~0.19 W/(m×K)) and transmittance (~0.20 W/(m²×K)) suggest good insulation performance. Field tests in three Colombian climate zones confirmed improved thermal comfort compared to traditional clay brick walls, with up to 8 °C internal temperature reduction. Acoustic analysis revealed higher sound attenuation in bio-bricks, especially at low frequencies. Chemical and morphological analyses (SEM-EDS, FTIR, and TGA) confirmed favorable thermal stability and the synergistic interaction of organic and inorganic components. The findings support bio-bricks’ potential as eco-efficient, low-carbon alternatives for sustainable building applications. Full article

In contemporary construction practices, polycarboxylate superplasticizers (PCEs) have gained extensive utilization in concrete formulation owing to their exceptional dispersive properties and superior water reduction capabilities. Nevertheless, these admixtures demonstrate pronounced susceptibility to clay contamination, a critical limitation that substantially constrains their practical implementation. To mitigate this detrimental effect, multiple technical strategies have been developed to suppress clay sensitivity, with predominant approaches focusing on molecular structure optimization and incorporation of supplementary admixtures. This review systematically investigates the competitive adsorption mechanisms operating at the cement–clay interface. Through rigorous analysis of molecular architecture characteristics and synergistic admixture combinations, we comprehensively review current methodologies for enhancing the clay resistance of PCE-based systems. Furthermore, this paper proposes prospective directions for synthesizing clay-tolerant PCE derivatives, emphasizing molecular design principles and advanced formulation protocols that may inform future research trajectories in construction materials science. Full article

In response to the need for sustainable soil stabilization alternatives, this study explores the use of waste materials and biopolymers to improve the mechanical behavior of clay from Cartagena, Colombia. Crushed limestone waste (CLW), ground glass powder (GG), recycled gypsum (GY), xanthan gum (XG), and the combination of XG with polypropylene fibers (XG–PPF) were used as stabilizing agents. Samples were compacted at different dry densities and cured for 28 days. Unconfined compressive strength (UCS) and ultrasonic pulse velocity (UPV) tests were conducted to assess the strength and stiffness of the treated mixtures. Results were normalized using the porosity/binder index ($\mathrm{\eta }/B_{iv}$), leading to predictive equations with high determination coefficients (R² = 0.94 for UCS and R² = 0.96 for stiffness). However, XG-treated mixtures exhibited distinct behavior that prevented their inclusion in a unified predictive model, as the fitted exponent x in the porosity/binder index ($\mathrm{\eta }/B_{iv}^x$) differed markedly from the others. While an exponent of 0.28 was suitable for blends with mineral binders, the optimal x values for XG and XG–PPF mixtures were significantly lower at 0.02 and 0.03, respectively, reflecting their unique gel-like and fiber-reinforced characteristics. The analysis of variance (ANOVA) identified cement content and compaction density as the most influential factors, while some interactions involving the residues were not statistically significant, despite aligning with experimental trends. The findings support the technical viability of using sustainable additives to enhance soil properties with reduced environmental impact. Full article

The stabilization of expansive soils is crucial for the construction projects to mitigate swelling, shrinkage, and bearing capacity issues. This study investigates the synergistic effects of cement and clinoptilolite zeolite on stabilizing high-plasticity clay (CH) soil from Kano State, Nigeria. A total of 30 admixture combinations—cement (0–8%) and zeolite (0–15%)—were tested via standardized laboratory methods to evaluate their free swell index (FSI), swell percentage, swell pressure, shrinkage, and California Bearing Ratio (CBR). Principal component (Lasso) “least absolute shrinkage and selection operator” regression modeled interactions between admixtures and soil properties. The key results include the following: (1) 6% cement + 12% zeolite reduced the FSI by 60% (45 → 18); (2) 8% cement + 15% zeolite decreased the swell percentage by 47.8% (22.5% → 11.75%); (3) 6% cement + 12% zeolite lowered swell pressure by 54.2% (240 kPa → 110 kPa); (4) 8% cement + 12% zeolite reduced shrinkage by 50% (5.6% → 2.8%); and (5) 6% cement + 9% zeolite achieved an unsoaked CBR of 80.01% and soaked CBR of 72.79% (resilience ratio: 0.8010). PCLR models explained 93.5% (unsoaked) and 75.0% (soaked) of the CBR variance, highlighting how zeolite’s mediation analysis indicates that zeolite improves the bearing capacity mainly by reducing the free swell index (path coefficient = −0.91429, p < 0.0001), while conditional process modeling provided greater explanatory power (R² = 0.745) compared to moderation-only analysis (R² = 0.618). This study demonstrates that zeolite–cement blends optimize strength and resilience in expansive soils, with implications for sustainable infrastructure in arid and semi-arid regions. Full article

This study identifies the following three key factors controlling shale gas reservoirs in the lower Cambrian Niutitang Formation, northern Guizhou, China: sedimentary features, diagenetic modification, and stable tectonic conditions. This research addresses gaps in previous studies by investigating how tectonic and diagenetic conditions contribute to the unique characteristics of shale gas enrichment in tectonically complex areas with high thermal maturity (R_o > 2.5%). Sedimentary conditions revealed a positive correlation between total organic carbon (TOC) content and gas adsorption capacity, with higher TOC enhancing adsorption. Experimental data indicate that the TOC content (2.33%–9.07%) significantly correlates with methane adsorption capacity (Langmuir volume VL = 1.87–8.78 cm³/g at 30 °C and 10 MPa), as evidenced by the linear relationship between TOC and VL in shale samples. Clay mineral content exhibited a dual role as moderate levels (15%–25%) improved adsorption, while excessive amounts (>30%) reduced efficiency due to pore occlusion. Diagenesis, including compaction, cementation, and thermal evolution of organic matter, significantly reshaped reservoir porosity. Quantitative analysis of core samples demonstrates that compaction caused a porosity reduction of 18%–25% in samples with burial depths exceeding 1500 m, thereby influencing gas retention capacity. The reservoir has entered the anchizone (average vitrinite reflectance R_o = 2.54%), characterized by advanced organic matter maturation and widespread organic porosity development. Tectonic activity was critical for gas retention; intense tectonic activity led to shallower burial depths and gas loss, whereas structurally stable areas favored preservation. This study emphasizes the significance of tectonic conditions and their role in maintaining gas reservoirs in the anchizone, reconciling discrepancies in gas storage mechanisms observed in basins with similar TOC and thermal maturity. In summary, deep marine shale gas enrichment relies on the synergistic effects of high-quality sedimentary foundations (TOC > 4%, quartz > 30%), diagenetic evolution optimizing pore structures, and stable tectonic conditions ensuring gas retention. These findings provide new insights into the exploration of shale gas in complex tectonic regions and offer a framework for improving prediction models in shale gas enrichment by integrating micro-scale organic–inorganic interactions with macro-scale tectonic controls. Full article

Deep coalbed methane (CBM) reservoirs have the characteristics of low permeability, low porosity, and low water saturation, which easily experience wellbore instability due to drilling fluid, severely affecting drilling safety. Based on the physical property analysis of coal samples, the wellbore instability mechanism of the deep CBM reservoir was investigated by multiple methods. It was found that the wellbore instability is mainly caused by drilling fluid intrusion and the interaction between drilling fluid and coal formation; the fracture pressure of coal after immersion decreased from 27.4 MPa to 25.0 MPa because of the imbibition of drilling fluid. A novel nano-plugging agent with a size of 460 nm was prepared that can cement coal particles to form disc-shaped briquettes with a tensile strength of 2.27 MPa. Based on that, an effective anti-collapse drilling fluid for deep coal rock reservoirs was constructed, the invasion depth of the optimized drilling fluid was only 6 mm. The CT result shows that the number of fractures and pores in coal rock significantly reduced after treatment with the wellbore-stabilizing drilling fluid; nano-plugging anti-collapse agent in drilling fluid can form a dense layer on the coal surface, and then the hydration swelling of clay in the wellbore region can be effectively suppressed. Finally, the drilling fluid in this work can achieve the purpose of sealing and wettability alternation to prevent the collapse of the wellbore in the deep coal reservoir. Full article

In order to reuse granulated blast furnace slag (GBFS) and low-strength soft clay (SC), this study developed a curing material using magnesium oxide (MgO) as an alkali activator to excite the GBFS and basalt fiber (BF) as reinforcing material to prepare the SC. The mixing ranges of GBFS, MgO, and BF were established as 9.48%~14.52%, 0.48%~5.52%, and 0%~1.00454% of the dry clay mass, respectively, and the mixing ratios of the three were optimized using the central composite design (CCD) test. Through the analysis of variance, factor interaction analysis, and parameter optimization of the CCD test, the optimal mass ratio of GBFS, MgO, and BF was determined to be 13.35:4.47:0.26. The curing material of this ratio was named GMBF and mixed with SC to prepare GMBF solidified clay. An equal amount of ordinary Portland cement (OPC) was taken and formed with SC to form OPC solidified clay. The mechanical properties, durability, and hydration products of GMBF solidified clay were clarified by the unconfined compressive strength (UCS) test, freeze–thaw cycle test, X-ray diffraction (XRD) test, and scanning electron microscopy (SEM) test. The UCS of the GMBF solidified clay was 1.08 MPa and 2.85 MPa at 7 and 91 days, respectively, which was 45.9% and 33.8% higher than that of the OPC solidified clay (0.74 MPa and 2.13 MPa) at the same curing time. After ten freeze–thaw cycles, the UCS of GMBF and OPC solidified clay decreased from the initial 2.85 MPa and 2.13 MPa to 1.59 MPa and 0.7 MPa, respectively, with decreases of 44.2% and 67.1%, respectively. By XRD and SEM, the hydration products of GMBF solidified clay were mainly calcium silicate hydrate gel and hydrotalcite. The interface bonding and bridging effect formed between BF and SC or hydration products, indicating that these interactions contributed to the solidified clay enhanced structural integrity. This study demonstrates that the CCD approach provides solution for recycling SC and GBFS. Laboratory tests confirm the potential of the optimized GMBF formulation for practical engineering applications. Full article

The fluid action mechanism and diagenetic evolution of tuff reservoirs in the Cretaceous Huoshiling Formation of the Dehui fault depression are discussed herein. The fluid properties of the diagenetic flow are defined, and the pore formation mechanism of the reservoir space is explained by means of thin sections, X-ray diffraction, electron probes, scanning electron microscopy (SEM), cathodoluminescence, and stable carbon and oxygen isotopic composition and fluid inclusion tests. The results reveal that the tuff reservoir of the Huoshiling Formation is moderately acidic, and the physical properties of the reservoir are characterized by middle to high porosity and ultralow permeability. The pore types are complex, comprising both primary porosity and secondary porosity, with dissolution pores and devitrification pores being the most dominant. Mechanical compaction and cementation are identified as key factors reducing reservoir porosity and permeability, while dissolution and devitrification processes improve pore structure and enhance pore connectivity. Diagenetic fluids encompass alkaline fluids, acidic fluids, deep-seated CO₊-rich hydrothermal fluids, and hydrocarbon-associated fluids. These fluids exhibit dual roles in reservoir evolution: acidic fluids enhance the dissolution of feldspar, tuffaceous materials, and carbonate minerals to generate secondary pores and improve reservoir quality, whereas alkaline fluids induce carbonate cementation, and clay mineral growth (e.g., illite) coupled with late-stage mineral precipitation obstructs pore throats, reducing permeability. The interplay among multiple fluid types and their varying dominance at different burial depths collectively governs reservoir evolution. This study underscores the critical role of fluid–rock interactions in controlling porosity–permeability evolution within tuff reservoirs. Full article

Sandy soils are a type of geomaterial that may require improvements due to lack of cohesion. In this study, first, the lack of cohesion of sand was resolved using clay, and the soil was stabilized with cement and lime (4% and 3% of the dry weight of materials, respectively) and finally reinforced with recycled tire fibers of 20 to 30 mm in length for improved strength and ductility. Next, 747 samples with different fiber contents at different curing temperatures and ages were prepared and a unconfined compressive strength (UCS) test was carried out. Next, a novel approach employing multivariate nonlinear regression techniques and obtained empirical data was applied to formulate a mathematical model for predicting the UCS and the modulus of elasticity (E_s) of the reinforced and stabilized soil. This model can serve as a valuable tool for building engineers in designing building foundations. The comparison of the obtained UCS and E_s results and those predicted using the proposed model showed a correlation of >95% (R² ≥ 0.95). The fibers effectively increased the failure strain, thus resulting in the greater ductility of the samples. As an example, in 14-day samples cured at 60 °C with 0%, 0.4%, 1%, 1.7%, and 2.5% fibers, the failure strain showed an incremental trend of 1.47%, 1.87%, 2.08%, 2.20%, and 2.92%, respectively. Scanning electron microscopy (SEM) was used to study the microstructure of the samples and to explain the strength experimental outcomes. SEM images showed a desirable interaction between the fiber surfaces with the soil mass and the reduction in porosity and the occurrence of pozzolanic reactions through stabilization. The results also showed that the reinforcement effectively improved the ductility, as desired for building foundations; however, it resulted in reduced strength, although a greater strength compared to the untreated soil was achieved. Although soil stabilization has been widely studied, limited research focuses on stabilizing soil with clay, lime, cement, and recycled tire fibers. This study offers design engineers an estimation scheme of the strength properties of stabilized and reinforced foundations. Full article

Limestone calcined clay cement (LC3), enhanced through reactions with volcanic ash and the interaction between limestone and clay, significantly improves the performance of cementitious materials. It has the potential to cut CO₂ emissions by up to 30% and energy consumption in cement manufacture by 15% to 20%, providing a promising prospect for the large-scale production of low-carbon cement with a lower environmental effect. To effectively manufacture LC3 concrete, this study utilized limestone (15%), calcined clay (30%), and gypsum (5%) as supplementary cementitious materials (SCMs), replacing 50% of ordinary Portland cement (OPC). However, in regions abundant in sulfate, sulfate attack can cause interior cracking of concrete, reducing the longevity of the building. To address this issue, microcapsules containing microcrystalline wax, ceresine wax, and nano-CaCO₃ encapsulated in epoxy resin were prepared and successfully incorporated into LC3 concrete. Sulfate resistance tests were conducted through sulfate dry–wet cycles, comparing samples with and without microcapsules. The findings revealed that the initial mechanical and permeability properties of LC3 concrete did not significantly differ from OPC concrete. LC3 concrete with added microcapsules (SP4) exhibited enhanced resistance to sulfate attack, reducing mass loss and compressive strength degradation. SEM images displayed a mesh-like structure of repair products in SP4. After 14 days of self-repair, SP4 exhibited a 44.2% harmful pore ratio, 98.1% compressive strength retention, 88.7% chloride ion diffusion coefficient retention, 91.12 mV maximum amplitude, and 9.14 mV maximum frequency amplitude. The experimental results indicate that the presence of microcapsules enhances the sulfate attack self-healing performance of LC3 concrete. Full article

As shield tunnels increase, managing shield muck strains construction and the environment. To mitigate this problem, shield muck replaced bentonite in silty clay to improve synchronous grouting slurry. Initially, the physical attributes and microstructural composition of shield muck were obtained, alongside an analysis of the effects of the muck content, particle size, and general influencing factors on the slurry properties through standardized tests and regression models. Subsequently, leveraging three-dimensional response surface methodology, admixture interactions and multiple factor impacts on the slurry were explored. Finally, utilizing the SQP optimization technique, an optimal slurry blend ratio tailored for actual project needs was derived for improved muck slurry. The findings reveal with the decreasing bleeding rates as the muck content rises, the particle size diminishes. An inverse relationship exists between the muck content and slurry fluidity. At soil–binder ratios below 0.6, a decrease in the soil–binder ratio intensifies the influence of the water–binder ratio on the slurry density, bleeding rate, and setting time. The fly flash–cement ratio inversely correlates with the slurry bleeding rate, while the ratio greater than 0.6 is positively correlated. For muck particle sizes under 0.2 mm, the fly flash–cement ratio inversely impacts the density, while over 0.2 mm, it correlates positively. The optimal proportion for silty clay stratum synchronous grouting slurry, substituting muck for bentonite, includes a water–binder ratio of 0.559, binder–sand ratio of 0.684, fly flash–cement ratio of 2.080, soil–binder ratio of 0.253, particle size under 0.075 mm, and water-reducing admixture of 0.06. Full article