Search Results (38)

High-frequency (h. f.) harmonic distortion (HD) of advanced SiGe heterojunction bipolar transistor (HBT)-based power cells (PwCs), featuring optimized metallization interconnections between individual HBTs, was investigated. Single tone input power (P_in) excitations at 1, 2, 5, and 10 GHz frequencies were employed. The output power (P_out) of the fundamental tone and its harmonics were analyzed in both the frequency and time domains. A rapid increase in the third harmonic of P_out was observed at input powers exceeding −8 dBm for a fundamental frequency of 10 GHz in two different PwC technologies. This increase in the third harmonic was analyzed in terms of nonlinear current waveforms, the nonlinearity of the HBT p-n junction diffusion capacitances, substrate current behavior versus P_in, and avalanche multiplication current. To assess the RF power performance of the PwCs, scalar and vectorial load-pull (LP) measurements were conducted and analyzed. Under matched conditions, the SiGe PwCs demonstrated good linearity, particularly at high frequencies. The key power performance of the PwCs was measured and simulated as follows: input power 1 dB compression point (P_{in_1dB}) of −3 dBm, transducer power gain (G_T) of 15 dB, and power added efficiency (PAE) of 50% at 30 GHz. All measured data were corroborated with simulations using the compact model HiCuM L2. Full article

Coronary artery disease (CAD) is the third leading cause of disability and death globally. Intravascular ultrasound (IVUS) is the most commonly used imaging modality for the characterization of vulnerable plaques. The development of novel intravascular imaging and therapy devices requires dedicated open systems (e.g., for pulse sequences for imaging or thrombolysis), which are not currently available. This paper presents the development of a novel multifunctional FPGA-based pulser/receiver system for intravascular ultrasound imaging and therapy research. The open platform consists of a host PC with a Matlab-based software interface, an FPGA board, and a proprietary analog front-end board with state-of-the-art electronics for highly flexible transmission and reception schemes. The main features of the system include the capability to convert arbitrary waveforms into tristate bipolar pulses by using the PWM technique and by the direct acquisition of raw radiofrequency (RF) echo data. The results of a multicycle excitation pulse applied to a custom 550 kHz therapy transducer for acoustic characterization and a pulse-echo experiment conducted with a high-voltage, short-pulse excitation for a 19.48 MHz transducer are reported. Testing results show that the proposed system can be easily controlled to match the frequency and bandwidth required for different IVUS transducers across a broad class of applications. Full article

Insulation materials are critical for the reliability and performance of electrical power systems, particularly in high-voltage rotating machines. While failures can arise from thermal, mechanical, or electrical stress, they predominantly manifest as electrical breakdowns. Prior research has primarily concentrated on aging in straight winding sections, despite evidence indicating that failures frequently occur in the bending regions of turn insulation. This study explores the influence of high-frequency pulsed electrical stress on the lifetime behavior of Type II insulation systems used in high-voltage rotating machines. Practical samples, designed with geometric configurations and technology akin to that in rotating machines, were tested under conditions characterized by voltage slew rates (dv/dt) exceeding 10 kV/μs, with variations in frequency and waveform shape. The findings reveal that the rate of electrical aging remains consistent across differing pulse widths, risetimes, and polarities, displaying a similar lifetime exponent. Nonetheless, insulation durability is markedly more compromised under pulsed conditions. At the identical times-to-failure, the sinusoidal waveform necessitated nearly twice the applied peak voltage as the bipolar pulse waveform. This finding clearly suggests that pulsed excitation exacerbates insulation degradation more effectively due to the sharp rise times and high (dv/dt) rates imposing substantial electrical stress on dielectric materials. Full article

Current-carrying coils and rotating permanent magnets can be used to create time-varying excitation magnetic fields for electrodynamic wireless power transmission (EWPT). Both types of transmitters produce low-frequency, time-varying fields at the locations of the receiver, but with fundamental differences. A coil transmitter produces a uniaxial magnetic field, where the direction of the field is along a single axis, but the amplitude varies in a bipolar fashion. In contrast, a rotating magnet transmitter produces a rotating magnetic field, with the amplitude varying in two orthogonal directions. Building on prior work for coil transmitters, this manuscript presents the modeling and a simulation framework for rotating magnet transmitters. The performance of an EWPT system is then studied both theoretically and experimentally for both transmitter types. For the same B-field amplitude (501 µT) and a fixed transmitter-receiver distance of 12 cm, a receiver driven by a coil transmitter produces 38 mW, whereas the same receiver driven by a rotating magnet transmitter produces 149 mW, nearly four times higher. This power increase is a result of 50% higher receiver rotation speeds using the rotating magnet transmitter. The power transfer efficiency is also six times higher for the rotating magnet transmitter. Full article

This paper presents a comparative study between two permanent magnet motor structures, one with trapezoidal waveforms and the other with sinusoidal waveforms, from the perspective of production cost, dynamic characteristic performance, and energy economy. The novel element of the research is also in using an electromagnetic converter to reduce the vehicle’s overall energy consumption and to push the multiple disadvantages of using the insolated bipolar transistors. This study is based on the sizing of the electromagnetic converter and the two motor structures using the method of combined analytical finite elements. The program for sizing is coupled with two control laws relating to the motor types in order to choose the top performers according to good dynamic characteristics and energy saving. The simulation results show, on the one hand, the equivalence of these structures from a dynamic characteristic point of view and, on the other hand, that the trapezoidal waveform motor structure is more economical. The design of an excitation system optimizing the consumed energy equipped by a hybrid excitation motor is also developed. Full article

In this study, a single-outer-spiral electrode with inductance of 20 μH is employed to couple the energy input of a bipolar nanosecond pulse for the purpose of generating a large-scale atmospheric pressure plasma jet. When the spiral electrode is wrapped around a plasma jet tube with a length of 35 cm, the electrical field can be optimized, resulting in a stable laminar flow field, and a plasma jet with a length and diameter larger than 14 cm and 1.2 cm can be generated. A comparative study of the bipolar and unipolar pulse excitation voltages is also conducted, showing that the maximum lengths of the plasma jet excited by a bipolar pulse voltage, positive pulse voltage, and negative are 14 cm, 10 cm, and 7 cm, respectively. The temporal and spatially resolved spectra of the plasma jets excited by both bipolar and unipolar pulses are investigated, respectively, and the main physiochemical processes of the active species and the plasma dynamics’ evolution are discussed. Full article

This paper studies the stability of a real-world wind farm, Bison Wind Generation System (BWGS) in the state of North Dakota in the United States. BWGS uses an AC collector grid rated at 34.5 kV and a symmetrical bipolar high-voltage DC (HVDC) transmission grid rated at ±250 kV. The HVDC line transfers a total power of 0.5 GW, while both the HVDC rectifier and inverter substations use line-commuted converters (LCCs). The LCC-based rectifier adopts constant DC current control to regulate HVDC current, while the inverter operates in constant extinction angle control mode to maintain a fixed HVDC voltage. This paper proposes a frequency scan-based approach to obtain the d–q impedance model of (i) BWGS AC collector grids with Type 4 wind turbines that use permanent magnet synchronous generators (PMSGs) and two fully rated converters, and (ii) an LCC-HVDC system. The impedance frequency response of the BWGS is acquired by exciting the AC collector grid and LCC-HVDC with multi-sine voltage perturbations during its steady-state operation. The resulting voltage and current signals are subjected to a fast Fourier transform (FFT) to extract frequency components. By analyzing the impedance frequency response measurement of BWGS, a linear time–invariant (LTI) representation of its dynamics is obtained using the vector fitting (VF) technique. Finally, a Bode plot is applied, considering the impedance of the BWGS and grid to perform stability analyses. This study examines the influence of the short circuit ratio (SCR) of the grid and the phase lock loop (PLL) frequency bandwidth on the stability of the overall system. The findings provide valuable insights for the design and verification of an AC collector and LCC-based HVDC transmission systems. The findings suggest that the extraction of the impedance model of a real-world wind farm, achieved through frequency scanning and subsequent representation as an LTI system using VF, is regarded as a robust, suitable, and accurate methodology for investigating the dynamics, unstable operating conditions, and control interaction of the wind farm and LCC-HVDC system with the AC grid. Full article

Linear induction launchers (LILs) are a specific subtype of linear motors. However, LILs are air-core machines that consistently operate in a transient rather than a steady state. Moreover, their operating currents and voltages exceed those of traditional machines. The execution time of LILs often remains within a few milliseconds, and it is essential to manage extremely high-power levels quickly. The control methods for LILs differ from those used for regular machines due to the differences from conventional linear motors. In this respect, there are still challenges to be overcome in power systems designed for LILs in the literature. This study has developed a novel power energization system to address these challenges, particularly in terms of inadequate V/f control and the unnecessary energization of regions along the barrel where no projectile is present. It focuses on the system’s design using multi-stage H-bridge inverters to produce a sinusoidal current for section-by-section polyphase excitation. An FPGA-based electronics control system generates bipolar PWM fiber-optical signals for IGBT switches for scalar V/f control of the inverters. Distributed multi-inverters power each stage of the launcher’s barrel and are controlled by the FPGA to create the travelling electromagnetic wave package. Three-dimensional FEM analysis is used for observation of the trigger timing to ensure positive force along the barrel. By driving each inverter independently, the coils on the barrel are excited sequentially based on the position of the projectile. This study also explains the implementation of a laboratory-scale barrel prototype, a 40 mm aluminum projectile, its power electronics, and the control part of the multi-stage inverters. In this study, 3300 V–1200 A IGBTs and 8.8 mF–2000 V DC-Link capacitors were used in the H-bridge inverter modules. Experimental studies have been conducted on the launcher, and the results obtained, including achieving a velocity of 30 m/s, are consistent with the electromagnetic simulations. It has been observed that the launcher, powered by the proposed system, is approximately 57.14% more efficient compared to the version energized by a single inverter. Full article

This article proposes and experimentally characterizes two implementations of a novel front-end circuit for three-wire connected resistive sensors with a wire-resistance compensation. The first implementation relies on two twin diodes, whereas the second on a switch; in both cases, those devices are non-remote (i.e., they are placed at the circuit end). The two circuit proposals have a square-wave input excitation so that a constant current with the two polarities is alternatively generated. Then, depending on that polarity, the current goes through either the sensor and the wire parasitic resistances or just the parasitic resistances. This generates a square-wave bipolar output signal whose average value, which is obtained by a low-pass filter, is proportional to the sensor resistance and only depends on the mismatch between two of the three wire resistances involved. Experimental tests applied to resistances related to a Pt100 thermal sensor show a remarkable linearity. For example, the switch-based front-end circuit offers a non-linearity error lower than 0.01% full-scale span, and this is practically insensitive to both the presence and the mismatch between the wire resistances. Full article

This paper proposes a nondestructive, separate transmitter-receiver (TX-RX) electromagnetic measurement system for near-surface detection. Different from the traditional dual-coil integrated design, the proposed transient electromagnetic (TEM) system performs shallow subsurface detection using independent TX coil and movable RX coils. This configuration requires a large primary field so that the far-away secondary field is able to generate reliably induced voltages. To achieve this goal, a bipolar current-pulsed power supply (BCPPS) with a late resonant charging strategy is designed to produce a sufficiently large magnetic moment for the exciting coil with low source interference. The magnetic dipole source (MDS) with a large proportion of weight is separated from the field observation device and does not need to be dragged or transported during the detection process. This setup lowers the weight of the scanning device to 3 kg and greatly improves the measurement efficiency. The results of the laboratory test verify the effectiveness of the separate MDS and RX module system. Field experimental detection further demonstrates that the proposed system can realize highly efficient and shallow surface detection within a 200 m range of the MDS device. Full article

This work aims to provide information about the deposition of gold via bipolar high-power impulse magnetron sputtering (HIPIMS) in order to identify suitable process parameters. The influences of voltage, pulse length and the kick-pulse on an argon–gold plasma during a bipolar high-power impulse magnetron sputtering deposition process were analysed via optical emission spectroscopy (OES) and oscilloscope. The voltage was varied between 700 V and 1000 V, the pulse length was varied between 20 µs and 100 µs and the process was observed once with kick-pulse and once without. The influence of the voltage on the plasma was more pronounced than the influence of the pulse width. While the intensity of several Au I lines increased up to 13-fold with increasing voltages, only a less-than linear increase in Au I brightness with time could be identified for changes in pulse length. The intensity of excited argon is only minimally affected by changes in voltages, but follows the evolution of the discharge current, with increasing pulse lengths. Contrary to the excited argon, the intensity emitted by ionized argon grows nearly linearly with voltage and pulse length. The reverse polarised pulse mainly affects the excited argon atoms in the plasma, while the influence on the ionized argon is less pronounced, as can be seen in the the spectra. Unlike the excited argon atoms, the excited gold atoms appear to be completely unaffected by the kick-pulse. No ionization of gold was observed. During the pulse, a strong rarefaction of plasma takes place. Very short pulses of less than 50 µs and high voltages of about 1000 V are to be preferred for the deposition of gold layers. This paper offers a comprehensive overview of the gold spectrum during a HIPIMS process and makes use of optical emission spectroscopy as a simple measuring approach for evaluation of the reverse polarized pulse during a bipolar process. Future uses of the process may include the metallization of polymers. Full article

Objectives: One of the current challenges in psychiatry is the search for answers on how to effectively manage drug-resistant depression. The occurrence of drug resistance in patients is an indication for the use of electroconvulsive therapy (ECT). This method is highly effective and usually results in relatively quick health improvement. Despite the knowledge of how ECT works, not all of the biological pathways activated during its use have been identified. Hence, based on the neuroinflammatory hypothesis of depression, we investigated the concentration of two opposite-acting adipokines (anti-inflammatory adiponectin and proinflammatory resistin) and BDNF in antidepressant-resistant patients undergoing ECT. Methods: The study group comprised 52 patients hospitalized due to episodes of depression in the course of unipolar and bipolar affective disorder. The serum concentration of adipokines and BDNF was determined before and after the therapeutic intervention using an ELISA method. In the analyses, we also included comparisons considering the type of depression, sex, and achieving remission. Results: Adiponectin, resistin, and BDNF concentrations change after ECT treatment. These changes are correlated with an improvement in the severity of depressive symptoms and are more or less pronounced depending on the type of depression. Conclusions: Although not all observed changes reach statistical significance, adipokines in particular remain exciting candidates for biomarkers in assessing the course of the disease and response to ECT treatment. Full article

Although a switched reluctance generator (SRG) is not the mainstream wind generator, it possesses the application potential and is worth developing for its many structural merits and high developed power ability. This paper presents a wind SRG-based bipolar DC microgrid having grid-connected and plug-in energy supporting functions. First, a surface-mounted permanent magnet synchronous motor (SPMSM)-driven wind turbine emulator (WTE) is established. Next, the wind SRG with an asymmetric bridge converter is developed. Good generating characteristics are obtained through proper designs of power circuit, commutation mechanism, external excitation source, voltage and current controllers. Third, a DC/DC boost interface converter and a bipolar voltage balancer are constructed to establish the 500 V microgrid bipolar DC-bus. To preserve the microgrid power supplying quality, a battery energy storage system (BESS) with bidirectional DC/DC interface converter is equipped. A dump load leg is added across the bus to limit the DC-bus voltage under energy surplus condition. In load side, a three-phase bidirectional load inverter is developed, which can be operated as a single-phase three-wire (1P3W) inverter or a three-phase three-wire (3P3W) inverter. Good sinusoidal voltage waveform and regulation characteristics are obtained using the proportional-resonant (PR) control. The microgrid to load and microgrid to grid operations are conductible. Finally, to further improve the powering reliability of microgrid, a three-phase T-type Vienna switch-mode rectifier (SMR) based plug-in energy supporting scheme is developed. When the microgrid energy shortage occurs, the possible harvested energy can be used to supply the microgrid. Full article

The anti-epileptic drug lamotrigine (LTG) has been widely used to treat various neurological disorders, including epilepsy and bipolar disorder. However, its precise mechanism of action in the central nervous system (CNS) still needs to be determined. Recent studies have highlighted the involvement of LTG in modulating the activity of voltage-gated ion channels, particularly those related to the inhibition of neuronal excitability. Additionally, LTG has been found to have neuroprotective effects, potentially through the inhibition of glutamate release and the enhancement of GABAergic neurotransmission. LTG’s unique mechanism of action compared to other anti-epileptic drugs has led to the investigation of its use in treating other CNS disorders, such as neuropathic pain, PTSD, and major depressive disorder. Furthermore, the drug has been combined with other anti-epileptic drugs and mood stabilizers, which may enhance its therapeutic effects. In conclusion, LTG’s potential to modulate multiple neurotransmitters and ion channels in the CNS makes it a promising drug for treating various neurological disorders. As our understanding of its mechanism of action in the CNS continues to evolve, the potential for the drug to be used in new indications will also be explored. Full article

This paper presents the evolution of an inductive wireless power transfer using a multicoil system. The double DD coil structure on the transmitter and the receiver side using two perpendicular bipolar DD coils is upgraded with an additional nonpolar quadrature coil. The proposed structure can be called the double DDQ coil structure. All three coils are not coupled, due to the nature of the directional double DD coil. If the transmitter and the receiver are not misaligned to one another, the system behaves as three separate, uncoupled IPT systems. The main advantage of the proposed coil topology is additionally increased power density and increased misalignment tolerance. Additionally, when the transmitter and the receiver coil are perfectly aligned, the proposed pad structure can transmit three different voltages and can be excited with different frequencies. In the case of this paper, the three coils on the transmitter side were excited by the same frequency. The proposed coil was evaluated experimentally and compared to the system using double DD coil structure. Full article