Search Results (1,274)

Bi₆Fe₂Ti₃O₁₈ (BFTO) ceramics were synthesized via a solid-state reaction route using stoichiometric amounts of Bi₂O₃, TiO₂, and Fe₂O₃ powders. A thermal analysis of the powder mixture was conducted to optimize the heat treatment parameters. Energy-dispersive X-ray spectroscopy (EDS) confirmed the conservation of the chemical composition following calcination. Final densification was achieved through hot pressing. The crystal structure of the sintered samples, examined via X-ray diffraction at room temperature, revealed a tetragonal symmetry for BFTO ceramics sintered at 850 °C. Electron backscatter diffraction (EBSD) provided detailed insight into the crystallographic orientation and microstructure. Broadband dielectric spectroscopy (BBDS) was employed to investigate the dielectric response of BFTO ceramics over a frequency range of 10 mHz to 10 MHz and a temperature range of −30 °C to +200 °C. The temperature dependence of the relative permittivity (ε_r) and dielectric loss tangent (tan δ) were measured within a frequency range of 100 kHz to 900 kHz and a temperature range of 25 °C to 570 °C. The impedance data obtained from the BBDS measurements were validated using the Kramers–Kronig test and modeled using the Kohlrausch–Williams–Watts (KWW) function. The stretching parameter (β) ranged from ~0.72 to 0.82 in the impedance formalism within the temperature range from 200 °C to 20 °C. Full article

Commercially available bismuth subcarbonate (Bi₂O₂CO₃) was treated with nitric acid and the surfactant cetyltrimethylammonium bromide. The treated catalysts exhibited enhanced photocatalytic activity compared to pure Bi₂O₂CO₃ in the decolorization of rhodamine B (RhB) under visible light irradiation. The absorbance at 554 nm gradually decreased over time and disappeared completely within 80 min. The crystal structure, morphology, and optical properties of the samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), UV-Vis diffuse reflectance spectroscopy (DRS), and photoluminescence (PL) spectroscopy. The improved photocatalytic activity of the treated catalysts was attributed to partial carbonate removal and the formation of Bi⁵⁺ species. Scavenger experiments indicated that superoxide radicals (·O₂⁻) and photogenerated holes (h⁺) played significant roles in the photocatalytic decolorization of RhB. Full article

Water pollution caused by increasing industrial and human activity remains a serious environmental challenge, especially due to the persistence of organic contaminants in aquatic systems. Photocatalysis offers a promising and eco-friendly solution, but in the case of bismuth oxide (Bi₂O₃) there is still a limited understanding of how structural and morphological features influence photocatalytic performance. In this work, a straightforward hydrothermal synthesis method followed by controlled calcination was developed to produce phase-pure α- and β-Bi₂O₃ with tunable morphologies. By varying the hydrothermal temperature and reaction time, distinct structures were successfully obtained, including flower-like, broccoli-like, and fused morphologies. XRD analyses showed that the final crystal phase depends solely on the calcination temperature, with β-Bi₂O₃ forming at 350 °C and α-Bi₂O₃ at 500 °C. SEM and BET analyses confirmed that morphology and surface area are strongly influenced by the hydrothermal conditions, with the flower-like β-Bi₂O₃ exhibiting the highest surface area. UV–Vis spectroscopy revealed that β-Bi₂O₃ also has a lower bandgap than its α counterpart, making it more responsive to visible light. Photocatalytic tests using Rhodamine B showed that the flower-like β-Bi₂O₃ achieved the highest degradation efficiency (81% in 4 h). Kinetic analysis followed pseudo-first-order behavior, and radical scavenging experiments identified hydroxyl radicals, superoxide radicals, and holes as key active species. The catalyst also demonstrated excellent stability and reusability. Additionally, Methyl Orange (MO), a more stable and persistent azo dye, was selected as a second model pollutant. The flower-like β-Bi₂O₃ catalyst achieved 73% degradation of MO at pH = 7 and complete removal under acidic conditions (pH = 2) in less than 3 h. These findings underscore the importance of both phase and morphology in designing high-performance Bi₂O₃ photocatalysts for environmental remediation. Full article

In this work, the synthesis and structural characterization of the smallest possible member of the family of bis-functionalized {MnMo₆O₂₄} Anderson–Evans polyoxometalates (POMs) is reported. The synthesis of the title compound TBA₃{[HC(CH₂O)₃]₂MnMo₆O₁₈} (1) was accomplished by using trimethylolmethane as the capping unit (TBA: tetra(n-butyl)ammonium, n-B_u4N⁺). The molecular structure of the organic–inorganic POM gave rise to yet undisclosed ¹H-NMR features, which are discussed thoroughly. Single-crystal X-ray diffraction (XRD) analysis revealed a highly regular 3D packing of the polyoxoanions within a matrix of TBA cations. The hybrid POM is of particular interest regarding potential applications in photocatalysis (i.e., hydrogen evolution) and energy storage. Thus, the electrochemical and thermal properties of 1 are also analyzed. Full article

The development of a silane coupling agent with an aminopropyl structure as a nucleating agent for poly(ethylene terephthalate) (PET) is reported in this study. The tri–block oligomers nucleating agent was formed by 1,3-bis(3-aminopropyl)-1,1,3,3-tetramethyldisiloxane/oxalic acid/low molecular weight PET (LPOBD). It was subsequently cross-linked with tetraethyl orthosilicate to form LPOBD-T. Composites of LPOBD/PET and LPOBD-T/PET were prepared by melt blending, and their thermal and crystallization behaviors were analyzed using XRD, DSC, TG, and POM. The results indicated that not only did the triblock polymer nucleating agent LPOBD exhibit a strong nucleation effect, but the crosslinked LPOBD-T also demonstrated superior crystallization performance. Specifically, the crystallinity of the 1 wt% LPOBD-T/PET composite increased by 3.3%, the crystallization temperature rose by 21.1 °C, and the t_1/2 was reduced by 53 s. Moreover, the crystalline morphology was more uniform. These findings indicate that the tri-block oligomers synthesized from a silane coupling agent serve as effective nucleating agents for PET. Full article

The Qiubudong silver deposit on the western margin of the Fuping ore cluster in the central North China Craton is a representative breccia-type deposit characterized by relatively high-grade ores, thick mineralized zones, and extensive alteration, indicating considerable potential for economic resource development and further exploration. Previous studies on this deposit have not addressed its genetic mineralogical characteristics. This study focuses on pyrite and quartz to investigate their typomorphic features, such as crystal morphology, trace element composition, thermoelectric properties, and luminescence characteristics, and their implications for ore-forming processes. Pyrite crystals are predominantly cubic in early stages, while pentagonal dodecahedral and cubic–dodecahedral combinations peak during the main mineralization stage. The pyrite is sulfur-deficient and iron-rich, enriched in Au, and relatively high in Ag, Cu, Pb, and Bi contents during the main ore-forming stage. Rare earth element (REE) concentrations are low, with weak LREE-HREE fractionation and a strong negative Eu anomaly. The thermoelectric coefficient of pyrite ranges from −328.9 to +335.6 μV/°C, with a mean of +197.63 μV/°C; P-type conduction dominates, with an occurrence rate of 58%–100% and an average of 88.78%. A weak–low temperature and a strong–high temperature peak characterize quartz thermoluminescence during the main mineralization stage. Fluid inclusions in quartz include liquid-rich, vapor-rich, and two-phase types, with salinities ranging from 10.11% to 12.62% NaCl equiv. (average 11.16%) and densities from 0.91 to 0.95 g/cm³ (average 0.90 g/cm³). The ore-forming fluids are interpreted as F-rich, low-salinity, low-density hydrothermal fluids of volcanic origin at medium–low temperatures. The abundance of pentagonal dodecahedral pyrite, low Co/Ni ratios, high Cu contents, and complex quartz thermoluminescence signatures are key mineralogical indicators for deep prospecting. Combined with thermoelectric data and morphological analysis, the depth interval around 800 m between drill holes ZK3204 and ZK3201 has high mineralization potential. This study fills a research gap on the genetic mineralogy of the Qiubudong deposit and provides a scientific basis for deep exploration. Full article

Ultra-high-molecular-weight polyethylene (UHMWPE) is a pivotal material in engineering and biomedical applications due to its exceptional mechanical strength, wear resistance, and impact performance. However, its extreme melt viscosity, caused by extensive chain entanglements, severely limits processability via conventional melt-processing techniques. Recent advances in catalytic synthesis have enabled the production of disentangled UHMWPE (dis-UHMWPE), which exhibits enhanced processability while retaining superior mechanical properties. Notably, heterogeneous catalytic systems, utilizing supported fluorinated bis (phenoxy-imine) titanium (FI) catalysts, polyhedral oligomeric silsesquioxanes (POSS)-modified Z-N catalysts, and other novel catalysts, have emerged as promising solutions, combining structural control with industrial feasibility. Moreover, optimizing polymerization conditions further enhances chain disentanglement while maintaining ultra-high molecular weights. These systems utilize nanoscale supports and ligand engineering to spatially isolate active sites, tailor the chain propagation/crystallization kinetics, and suppress interchain entanglement during polymerization. Furthermore, characterization techniques such as melt rheology and differential scanning calorimetry (DSC) provide critical insights into chain entanglement, revealing distinct reorganization kinetics and bimodal melting behavior in dis-UHMWPE. This development of hybrid catalytic systems opens up new avenues for solid-state processing and industrial-scale production. This review highlights recent advances concerning interaction between catalyst design, polymerization control, and material performance, ultimately unlocking the full potential of UHMWPE for next-generation applications. Full article

The paper presents a study of changes in selected physicochemical properties of honeys during their refrigerated storage at 8 ± 1 °C for 24 weeks. On the basis of the study of primary pollen, the botanical identification of the variety of honeys was made—rapeseed, multiflower and buckwheat honey. The samples were stored for 24 weeks in dark, hermetically sealed glass containers in a refrigerated chamber (8 ± 1 °C, 73 ± 2% relative humidity). The comprehensive suite of analyses comprised sugar profiling (ion chromatography), moisture content determination (refractometry), pH and acidity measurement (titration), electrical conductivity, color assessment in the CIELab system (ΔE and BI indices), texture parameters (penetration testing), rheological properties (rheometry), and microscopic evaluation of crystal morphology; all data were subjected to statistical treatment (ANOVA, Tukey’s test, Pearson correlations). The changes in these parameters were examined at 1, 2, 3, 6, 12, and 24 weeks of storage. A slight but significant increase in moisture content was observed (most pronounced in rapeseed honey), while all parameters remained within the prescribed limits and showed no signs of fermentation. The honeys’ color became markedly lighter. Already in the first weeks of storage, an increase in the L* value and elevated ΔE indices were recorded. The crystallization process proceeded in two distinct phases—initial nucleation (occurring fastest in rapeseed honey) followed by the formation of crystal agglomerates—which resulted in rising hardness and cohesion up to weeks 6–12, after which these metrics gradually declined; simultaneously, a rheological shift was noted, with viscosity increasing and the flow behavior changing from Newtonian to pseudoplastic, especially in rapeseed honey. Studies show that refrigerated storage accelerates honey crystallization, as lower temperatures promote the formation of glucose crystals. This accelerated crystallization may have practical applications in the production of creamed honey, where controlled crystal formation is essential for achieving a smooth, spreadable texture. Full article

To ensure the sustainable use of limited resources, it is essential to establish selective and efficient recycling technologies for platinum group metals (PGMs). This study focused on the selective precipitation-based separation of Pt(IV) from hydrochloric acid (HCl) solutions in the presence of various metal ions, using trans-1,4-bis(aminomethyl)cyclohexane (BACT) as a precipitating agent. By using BACT, we succeeded in the selective separation of Pt(IV) by precipitation from HCl solutions containing Pd(II) and Rh(III). Notably, selective and efficient recovery of Pt(IV) was accomplished across various HCl concentrations, with a small amount of BACT and within a short shaking time. To evaluate the practical applicability of the method, Pt(IV) was recovered and purified from the HCl leachate of spent automotive exhaust gas purification catalysts using BACT. As a result, a high Pt recovery of 95.6% and a high purity of 99.3% were achieved. Although Pt(IV) was recovered as a precipitate containing BACT, it was found that Pt black could be readily obtained by dissolving the precipitate in HCl solution followed by reduction with sodium borohydride. Detailed structural analysis of the Pt(IV)-containing precipitate revealed that it is an ionic crystal composed of [PtCl₆]²⁻ and protonated BACT. The selective formation of this ionic crystal in HCl solution, along with its stability under such conditions, is the key to the selective recovery of Pt(IV) using BACT. Full article

Na₀.₈₉Co_0.90Me_0.10O₂ (Me = Cr, Ni, Mo, W, Pb, and Bi) ceramic samples were prepared using a solid-state reaction method, and their crystal structure, microstructure, and electrical, thermal, and thermoelectric properties were investigated. The effect of the nature of the doping metal (Me = Cr, Ni, Mo, W, and Bi) on the structure and properties of layered sodium cobaltite Na_0.89CoO₂ was analyzed. The largest Seebeck coefficient (616 μV/K at 1073 K) and figure-of-merit (1.74 at 1073 K) values among the samples studied were demonstrated by the Na_0.89Co_0.9Bi_0.1O₂ solid solution, which was also characterized by the lowest value of the dimensionless relative self-compatibility factor of about 8% within the 673–873 K temperature range. The obtained results demonstrate that doping of layered sodium cobaltite by transition and heavy metal oxides improves its microstructure and thermoelectric properties, which shows the prospectiveness of the used doping strategy for the development of new thermoelectric oxides with enhanced thermoelectric characteristics. It was also shown that samples with a higher sodium content (Na:Co = 0.89:1) possessed higher chemical and thermal stability than those with a lower sodium content (Na:Co = 0.55:1), which makes them more suitable for practical applications. Full article

Developing functional perovskites is important for advancing solar energy conversion technologies. This study investigates the effects of dopants on the structural, optical, electronic, and solar conversion performances of Ba₂M_0.4Bi_1.6O₆ double perovskites. X-ray diffraction (XRD) and Rietveld refinement confirm crystallization in the I2/m space group (M = La, Ce, Pr, Pb), and Fm$\overline{3}$m and I2/m space groups (M = Y). The B1-O-B2 structure modulates to highly ordered (M = La, Y), partially ordered (M = Pr), or disordered (M = Ce, Pb). UV-vis spectra show strong light absorption, with Tauc plots estimating ~1.57 eV (M = La) and ~1.73 eV (M = Pr) optical band gaps. Under AM 1.5G illumination, the M = La photoelectrode generates photocurrents of 1 mA cm⁻² at 0.3 V_RHE, surpassing M = Ce and Pb (1 μm, 4-times spin-coating). Increasing its thickness to 7.7 μm (4-times dip-coating) further enhances the photocurrents to 2.3 mA cm⁻² at 0.2 V_RHE, outperforming all counterparts due to improved stability. Fine-tuning crystal and electronic structures via strategic B-site doping provides a new route for engineering Ba₂Bi₂O₆-based double perovskites for broad solar energy conversion applications. Full article

Understanding strain behavior near grain boundaries is critical for controlling structural distortions and oxygen vacancy migration in perovskite oxides. However, conventional techniques often lack the spatial resolution needed to analyze phase and domain evolution at the nanoscale. In this paper, polarization-dependent second-harmonic generation (SHG) imaging is employed as a tool to probe local symmetry breaking and complex domain structures in the vicinity of a low-angle grain boundary of SrTiO₃ (STO) bicrystals. We show that the anisotropic strain introduced by a tilted grain boundary produces strong local distortions, leading to the coexistence of tetragonal and rhombohedral domains. By analyzing SHG intensity and variations in the second-order nonlinear optical susceptibility, we map the distribution of strain fields and domain configurations near the boundary. In pristine samples, the grain boundary acts as a localized source of strain accumulation and symmetry breaking, while in samples subjected to intentional electrical stressing, the SHG response becomes broader and more uniform, suggesting strain relaxation. This work highlights SHG imaging as a powerful technique for visualizing grain-boundary-driven structural changes, with broad implications for the design of strain-engineered functional oxide devices. Full article

Heavier element analogues of a ketone, a C=O double-bond compound, have been fascinating compounds from the viewpoint of main-group element chemistry because of their unique structural features and reactivity as compared with those of a ketone, which plays an important role in organic chemistry. We will report here the synthesis of diorgano-stannanethione and stannaneselone featuring tin–chalcogen double bonds, which are the heavy-element analogues of a ketone. The newly obtained stannaneselone has been structurally characterized by spectroscopic analyses and single-crystal X-ray diffraction (SC-XRD) analysis, showing the short Sn–Se bond length featuring π-bond character. The obtained bis(ferrocenyl)stannanechalcogenones were found to undergo [2+4]cycloaddition reactions with 2,3-dimethyl-1,3-butadiene, affording the corresponding six-membered ring compound. Notably, thermolysis of the [2+4]cycloadduct of the stannaneselone regenerated the stannaneselone via the retro[2+4]cycloaddition, whereas the sulfur analogue was thermally very stable. Full article

Topological insulators (TIs) can be widely applied in the fields of ultrafast optical and spintronic devices owing to the existence of topologically protected gapless Dirac surface states. However, the study of ultrafast dynamics of carriers in TIs remains elusive. In this work, the carrier dynamics of Li-doped Bi_2−xSe₃ single crystals were investigated by femtosecond (fs) transient optical spectroscopy (ΔR/R(t) signals). The temperature dependence for the relaxation rates of the electron–electron interaction and electron–phonon coupling is consistent with the results of electrical transport, which indicates the carrier dynamics of TI is highly related with carrier concentrations. We find that the carrier type and concentration of Bi₂Se₃ can be tuned by Li doping, leading to a metal-insulation transition at low temperatures (T ≤ 55 K), indicating that electron–electron interactions are dominant at low temperature. For T > 55 K, electron–phonon coupling in the bulk carriers becomes the main electric transport mechanism. Full article

Phenylene-based bis-oxamate polydentate ligands offer a unique opportunity for creating a large variety of coordination compounds, in which paramagnetic metal ions are strongly magnetically coupled. The employment of imino nitroxyl (IN) radicals as supplementary ligands confers numerous benefits, including the strong ferromagnetic interaction between Ni and IN. Furthermore, the chelating IN can act as a capping ligand, thereby impeding the formation of coordination polymers. In this study, we present the molecular and crystal structure and experimental and theoretical magnetic behavior of an exceptional neutral trinuclear complex [Ni(L³⁻)₂(IN)₃]∙5CH₃OH (1) (L is N,N′-1,3-phenylenebis-oxamic acid; IN is [4,4,5,5-tetramethyl-2-(6-methylpyridin-2-yl)-4,5-dihydro-1H-imidazol-1-yl]oxidanyl radical) with a cyclic triangular arrangement. Moreover, in this compound three Ni²⁺ ions are linked by the two bis-oxamate ligands playing a rare tritopic function due to an unprecedented triple deprotonation of the related meta-phenylene-bis(oxamic acid). The main evidence of such a deprotonation of the ligand is the neutrality of the cluster, since there are no anions or cations compensating for its charge in the crystals of the compound. Despite the presence of six possible magnetic couplings in the trinuclear cluster 1, its behavior was reproduced with a high degree of accuracy using a three-J model and ZFS, under the assumption that the three different Ni-IN interactions are equal to each other, whereas only two equivalent-in-value Ni-Ni interactions were taken into account, with the third one being equated to zero. Our study indicates the presence of two opposite-in-nature types of magnetic interactions within the triangular core. DFT and CASSCF/NEVPT2 calculations were completed to support the experimental magnetic data simulation. Full article