Search Results (429)

Two gold-decorated wooden sculptures of Qing Dynasty collected in Qianjiang Cultural Administration Institute, Chongqing, China, holds significant cultural value. Although in appearance they were preserved completely, the wooden bodies exhibited a certain degree of decay with severe peeling of the surface painted layer and gold lacquer layer. In this study, the samples from the sculptures were characterized by microscopy, SED–EDS (Scanning Electron Microscopy and Energy Dispersive Spectrometer) analysis, and Raman spectroscopy, while the preservation state of wooden core was assessed through the fluorescence microscopy and NREL (National Renewable Energy Laboratory) chemical analysis methods. Findings reveal that the raw material for wooden sculpture is cypress, and holocellulose content of wooden core is as low as 32%. The raw materials for red pigment include cinnabar (HgS) and hematite (Fe₂O₃). There are multiple layers of lacquer and gold can be observed. There is a layer made of clay, gypsum, or brick ash beneath the lacquer layer and colored layer. The gold layer on the surface adopted traditional Chinese gilding technique which is called sticking gold. This study provides insights into the material properties and technological features of these wooden sculptures, offering a reference for future protection of similar sculptures. Full article

The potential for creating composite cements by incorporating fly ash is demonstrated. Analysis revealed that the fly ash examined consists of 69.66 wt. % silicon oxide, 21.34 wt. % aluminum oxide, 1.57 wt. % calcium oxide and 2.78 wt. % iron oxide. Fly ash mainly consists of quartz (SiO₂), goethite (FeO(OH)) and mullite (3Al₂O₃·2SiO₂). The properties of the cement composition containing 5 to 25 wt. % fly ash were studied. Incorporating fly ash enhances system dispersion, promotes mixture uniformity, and stimulates the pozzolanic reaction. Compositions of composite cements consisting of 90% CEM I 42.5 and 10% fly ash were developed. The cement stone based on the obtained composite cement had a compacted structure with a density of 2.160 g/cm³, which is 9.4% higher than the control sample. It is shown that when composite cement containing 10% fly ash interacts with water, hydration reactions of cement minerals (C₃S, C₂S, C₃A and C₄AF) begin first. This is accompanied by the formation of hydrate neoplasms, such as calcium hydroxide (Ca(OH)₂) and calcium hydrosilicates (C-S-H). Fly ash particles containing amorphous silica progressively participate in a pozzolanic reaction with Ca(OH)₂, leading to the formation of additional calcium hydrosilicates phases. This process enhances structural densification and reduces the porosity of the cement matrix. After 28 days of curing, the compressive strength of the resulting composite cements ranged from 42.1 to 54.2 MPa, aligning with the strength classes 32.5 and 42.5 as specified by GOST 31108-2020. Full article

The Chengyang City (城阳城) site in Xinyang, Henan Province, China, was a significant northern military stronghold of the Chu state during the Warring States period (475/403–221 BCE). The lacquered armor unearthed from Tomb M18 provides critical material evidence for studying ancient military technology and lacquer craftsmanship. In this study, a comprehensive analytical approach combining ultra-depth optical microscopy, Fourier-transform infrared spectroscopy (FTIR), confocal micro-Raman spectroscopy, scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDS) and pyrolysis–gas chromatography/mass spectrometry (Py-GC/MS) were employed to systematically characterize the structural and compositional features of the armor samples. The results indicate that the armor was constructed with a leather substrate and lacked any lacquer ash layer, while the surface exhibited multiple layers of mixed laccol and urushiol-based lacquer coatings. Cinnabar (HgS) was identified as the primary red pigment, and no carbon black or iron-based blackening agents were detected in the dark lacquer layers. Notably, the presence of laccol suggests that such lacquer resources may have also been produced in mainland China, offering new perspectives on the prevailing view that associates laccol exclusively with “Vietnamese lacquer.” This study elucidates the technological characteristics of mid-Warring States period lacquered armor, provides scientific insights into ancient lacquering techniques, and contributes valuable data for the conservation and restoration of similar cultural heritage artifacts. Full article

The Rotunda in Thessaloniki, Greece, preserves in its interior a magnificent wall mosaic assemblage of unique inspiration and beauty. Thirty-six (36) glass tesserae, blue, green, yellow, brown, black, gold and silver in color, were examined for the first time via UV-Vis reflectance spectroscopy, scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS) and X-ray diffraction (XRD) analysis, in order to investigate the base glass composition, and their technological and morphological features. Despite the heterogeneity observed in the glass composition, the results indicated similarities with other Early Christian and Byzantine wall mosaics in the use of colorants, opacifiers and decolorizers. Cobalt, copper, iron and manganese along with lead and tin compounds are responsible for the blue, green, yellow, brown and black colors. Tin-based opacifiers and bone ash contribute to the glass opacity. The use of different glass recipes and opacifiers in the Rotunda’s assemblage reflects the transition from the Roman glass tradition to the Byzantine glass production of the fourth and the fifth century in the eastern Mediterranean. Full article

Recent tailing dam failures in Brazil have been attributed to liquefaction. Chemical stabilization offers a promising solution to enhance the strength and stiffness of tailings and mitigate liquefaction potential. This study investigated the mechanical and microstructural behavior of gold mine tailings (GMTs) stabilized using (i) an alkali-activated binder composed of sugar cane bagasse ash (SCBA), hydrated eggshell lime (HEL), and sodium hydroxide (NaOH) and (ii) Portland cement (PC). Drained and undrained triaxial shear tests and scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS) analyses were performed. Specimens stabilized with Portland cement exhibited a strong strain-softening behavior and the highest strength, with 5.3 MPa under 200 kPa confining pressure compared to 2.3 MPa for alkali-activated samples and 740 kPa for untreated GMTs. The addition of either binder also increased both the peak effective friction angle and the critical state stress ratio, confirming an enhanced shear strength. SEM-EDS analyses confirmed the formation of cementitious reaction products, explaining these improvements. This research validates both binders as viable solutions for tailing stabilization, with the novel alkali-activated binder offering a sustainable alternative for large-scale applications. Full article

The Lunayyir Volcanic Field (Harrat Lunayyir), located on the western boundary of the Arabian Microplate, comprises a Quaternary volcanic region featuring approximately 150 volcanoes formed from around 700 vents. In 2009, a significant volcano-seismic event occurred, resulting in the formation of a nearly 20 km long fissure. Geophysical modeling has demonstrated that this area lies above an eruptible magma system, unequivocally confirming ongoing volcanic activity. Recent geological mapping and age determinations have further established the field as a young Quaternary volcanic landscape. Notably, the 2009 event provided critical evidence of the region’s volcanic activity and underscored the potential to connect its volcanic geoheritage with hazard mitigation strategies. The volcanic field displays diverse features, including effusive eruptions—primarily pāhoehoe and ‘a‘ā lava flows—and explosive structures such as spatter ramparts and multi-crater scoria cones. While effusive eruptions are most common and exert long-term impacts, explosive eruptions tend to be less intense; however, some events have reached a Volcanic Explosivity Index (VEI) of 4, distributing ash up to 250 km. Recognizing the geoheritage and geodiversity of the area may enhance resilience to volcanic hazards through geoconservation, educational initiatives, managed visitation, and establishment of a geoheritage reserve to preserve site conditions. Hazards associated with this dispersed monogenetic volcanic field manifest with recurrence intervals ranging from centuries to millennia, presenting challenges for effective communication. Although eruptions are infrequent, they have the potential to impact regional infrastructure. Documentation of volcanic geoheritage supports hazard communication efforts. Within the northern development sector, 26 geosites have been identified, 22 of which pertain to the Quaternary basaltic volcanic field, each representing a specific hazard and contributing vital information for resilience planning. Full article

The aim of the present note is to contribute to the search for sustainable binders to be used for soil stabilization purposes. Fly ash and quicklime are added to a clayey soil of low plasticity in different proportions; samples were prepared by wet mixing and Standard Proctor compaction of the soil–water–binder mixture. Permeability tests were carried out for the first 28 days of curing, varying the moulding water content of the investigated samples. Compressibility was evaluated through one-dimensional consolidation tests performed after 7 days of curing and shear strength was investigated at the same curing time. Reactions development was successfully monitored by measuring pH and small strain shear modulus by means of bender elements testing for the first 28 days of curing. Microstructural investigation through scanning electron microscope and Energy dispersive X-Ray Spectroscopy revealed the presence of pozzolanic products in the mixture, reflecting the reduction in compressibility and the improvement in the mechanical characteristics of the soil of concern, after the treatment. The addition of the combination of fly ash and quicklime allowed to enhance the draining capability of the mixtures, especially when the mixture is compacted at optimum water content. Full article

Considering the current requirement for high temperatures and the significant energy consumption in the preparation of geopolymer-based cements, this paper presents a study on the compressive strength of metakaolin-based geopolymers containing various low-calcium fly ash admixtures, prepared at room temperature (25 ± 2 °C). The physical properties and microstructure of the geopolymers were characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). The type of alkaline cations, phase transformation, evolution of characteristic functional groups, and hydration characteristics of the microstructures were analyzed, and the hydration mechanism is discussed. The experimental results indicated that the fly ash content had a more significant impact on compressive strength than the alkaline cation type (Na⁺/K⁺). The optimal formulation (20% fly ash with 20% KOH activator) reached a compressive strength of 76.70 MPa at 28 days, which was around 6% higher than that of the NaOH-activated counterpart (72.34 MPa). Crystalline phase analysis in the transformation of mullite and microstructure analysis indicated that the increase in compressive strength could be attributed to the effective filling of the matrix interface by chemically inert fillers and the dense N-A-S-H and C-(A)-S-H multi-dimensional gel structures. These experiments prove the feasibility of using fly ash and metakaolin to prepare geopolymer materials with high compressive strength at room temperature. Full article

High-calcium fly ash (HCFA), produced from the lignite combustion, has emerged as a global concern due to its fine particle size and adverse environmental impacts. This study presents the characteristics of dispersed microspheres from HCFA obtained using modern techniques, such as XRD, SEM-EDS, ⁵⁷Fe Mössbauer spectroscopy, DSC-TG, particle size analysis, and magnetic measurements. It is found that an increase in microsphere size is likely due to the growth of the silicate glass-like phase, while the magnetic crystalline phase content remains stable. According to the ⁵⁷Fe Mössbauer spectroscopy, there are two substituted Ca-based ferrites—CaFe₂O₄ and Ca₂Fe₂O₅ with a quite different magnetic behavior. Besides, the magnetic ordering temperature of the brownmillerite (Ca₂Fe₂O₅) phase increases with the average diameter of the microspheres. FORC analysis reveals enhanced magnetic interactions as microsphere size increases, indicating an elevation in the concentration of magnetic microparticles, primarily on the microsphere surface, as supported by electron microscopy data. The discovered the magnetic crystallographic phases distribution on the microsphere’s surface claims the accessibility for further enrichment of the magnetically active particles and the possible application of fly ashes as a cheap source for magnetic materials synthesis. Full article

In recent years, recovering critical elements from coal has attracted considerable interest due to their significant potential and resulting advantages. A prime example is the coal-hosted Al-Ga-Li-REE deposit within the Jungar Coalfield of Inner Mongolia, northern China, where lithium (Li), gallium (Ga), and aluminum (Al) are successfully extracted from coal ash. However, the specific forms in which these elements exist, crucial for developing effective extraction methods, remain unquantified. This research investigated the distribution of Li, Ga, Nb, Zr, and rare earth elements (REEs) within the coal. The study employed a combination of analytical techniques, including inductively coupled plasma mass spectrometry (ICP-MS), sequential chemical extraction (SCE), scanning electron microscopy coupled with energy-dispersive X-ray spectrometry (SEM-EDS), and X-ray powder diffraction analysis (XRD). The analyzed coals exhibited enriched levels of Li, Ga, Zr, Nb, and REEs. Kaolinite and boehmite were the primary mineral constituents, along with minor amounts of calcite, pyrite, rutile, goyazite, and chlorite. Sequential chemical extraction revealed that Li and Ga are primarily associated with aluminosilicate phases (71.84%–84.39%) and, to a lesser degree, organic matter (12.15%–25.09%). Zirconium and Nb were also predominantly found within aluminosilicates (68.53%–95.96%). REEs occur mainly in carbonate (28.28%–60.78%), aluminosilicate (11.6%–33.08%), and organic (22.04%–29.42%) fractions. Full article

This study evaluated the feasibility of reusing abandoned copper mine tailings (Cu tailings) as a precursor in the production of fly-ash-based alkali-activated materials (FA-AAMs). Two formulations were developed by combining FA and Cu tailings with a mixture of sodium silicate and sodium hydroxide as alkaline activators at room temperature (20 °C). Formulation G1 consisted of 70% Cu tailings and 30% fly ash (FA), whereas G2 included the same composition with an additional 15% ordinary Portland cement (OPC). The materials were characterized using X-ray fluorescence (XRF), -X-ray diffraction (XRD), field emission scanning electron microscopy with energy-dispersive spectroscopy (FESEM-EDS), and particle size analysis. While FA exhibited a high amorphous content (64.4%), Cu tailings were largely crystalline and acted as inert fillers. After 120 days of curing, average compressive strength reached 24 MPa for G1 and 41 MPa for G2, with the latter showing improved performance due to synergistic effects of geopolymerization and OPC hydration. Porosity measurements revealed a denser microstructure in G2 (35%) compared to G1 (52%). Leaching tests confirmed the immobilization of hazardous elements, with arsenic concentrations decreasing over time and remaining below regulatory limits. Despite extended setting times (24 h for G1 and 18 h for G2) and the appearance of surface efflorescence, both systems demonstrated good chemical stability and long-term performance. The results support the use of Cu tailings in FA-AAMs as a sustainable strategy for waste valorization, enabling their application in non-structural and moderate-load-bearing construction components or waste encapsulation units. This approach contributes to circular economy goals while reducing the environmental footprint associated with traditional cementitious systems. Full article

This study investigates the composition–property relationships in ternary engineered geopolymer composites (EGCs) using a simplex centroid design method to optimize the synergy between ground granulated blast furnace slag (GGBS), fly ash (FA), and metakaolin (MK). Mechanical testing revealed that compressive strength (>85 MPa) peaked at 75% GGBS/25% MK, demonstrating MK’s dominant role in enhancing densification, while flexural strength showed a negative correlation with GGBS content but consistent improvement with MK addition. Strain-hardening behavior was most pronounced in 75% GGBS/25% MK and 83% GGBS/8% FA/8% MK mixtures, with the latter achieving optimal precursor synergy. Fiber dispersion uniformity showed a strong linear correlation (R² = 0.98) with tensile strain capacity, confirming its critical role in strain-hardening performance. Mercury intrusion porosimetry analysis demonstrated that the G83F8M8 mixture exhibited the lowest porosity (<10%) and finest pore size distribution (50–100 nm dominant), directly linking pore refinement to superior mechanical properties. Full article

Rare earth elements (REYs) are crucial components of billions of products worldwide. Transitioning from foreign to domestic REY sources requires utilizing both primary (i.e., carbonatites, alkaline igneous rocks, pegmatites, skarn deposits) and secondary (unconventional) sources (i.e., ion-adsorption clays, placer deposits, weathered rock, black and/or oil shales). Coal and coal-bearing strata, promising secondary REY resources, are the focus of this study. Understanding REY mineral associations in unconventional resources is essential to quantifying resource volume and identifying viable mineral separation and processing techniques. Highly REY-enriched (>750 ppm) coal or mudstone samples from the Uinta Region, Utah, USA, were selected for scanning electron microscopy (SEM) analysis. Energy dispersive X-ray spectroscopy (EDS)-determined REY enrichment occurs in: (1) a silt-size fraction (5–30 μm) of monazite and xenotime REY-enriched grains, (2) a clay-size fraction (2–5 μm) of monazite REY-enriched grains dispersed in the clay-rich matrix, and (3) organically confined REY domains < 2 μm. Findings suggest possible REY enrichment from multiple sources, including: (1) detrital silt-size grains, (2) volcanic ash fall, largely in clay-size grains, and (3) organic REY uptake in the peat swamp depositional environment. Full article

By proportionally blending fresh latex from PR107, Reyan 72059, and Reyan 73397, and employing both acid- and enzyme-assisted microbial coagulation methods, this study analyzed the effects of the specific latex formulation on the following: physicochemical properties, non-rubber components, molecular weight and distribution, vulcanization characteristics of compounded rubber, and physical–mechanical properties of vulcanized natural rubber. The results indicate that, compared to acid-coagulated natural rubber, enzyme-assisted microbial coagulated natural rubber exhibits slightly lower levels of volatile matter, impurities, plasticity retention index (PRI), nitrogen content, calcium ions (Ca²⁺), iron ions (Fe³⁺), and fatty acid content. Conversely, it demonstrates higher values in ash content, initial plasticity (P₀), Mooney viscosity (M_L(1+4)), acetone extract, magnesium ions (Mg²⁺), copper ions (Cu²⁺), manganese ions (Mn²⁺), gel content, molecular weight and distribution, and glass transition temperature (Tg). With the increase in the proportion of PR107 and Reyan 72059 fresh latex, the ash content, volatile matter content, fatty acid content, gel content, and dispersion coefficient (PDI) of natural rubber gradually decrease, while the impurity content, PRI, nitrogen content, weight-average molecular weight (Mw), and number-average molecular weight (Mn) gradually increase. Compared to acid-coagulated natural rubber compounds, enzyme-assisted microbial-coagulated natural rubber compounds exhibit higher minimum torque (M_L) and maximum torque (M_H), but shorter scorch time (t₁₀) and optimum cure time (t₉₀). Furthermore, as the proportion of PR107 and Reyan 72059 fresh latex increases, the ML of the compounds gradually decreases. In pure rubber formulations, enzyme-assisted microbial-coagulated natural rubber vulcanizates demonstrate higher tensile strength, tear strength, modulus at 300%, and Shore A hardness compared to acid-coagulated natural rubber vulcanizates. When the fresh latex ratio of PR107, Reyan 72059, and Reyan 73397 is 1:1:3, the tensile strength and 300% modulus of the natural rubber vulcanizates reach their maximum values. In carbon black formulations, the tensile strength and tear strength of enzyme-assisted microbial-coagulated natural rubber vulcanizates are significantly higher than those of acid-coagulated natural rubber vulcanizates in pure rubber formulations, with the increase exceeding that of other samples. Full article

To address the environmental risks associated with large-scale stockpiling of red mud (RM) and coal gangue (CG) and the demand for their high-value utilization, this study proposes a ternary concrete system incorporating RM, fly ash (FA), and CG aggregate. The effects of RM content, FA content, CG aggregate replacement rate, and water-to-binder ratio on workability, mechanical properties, and frost resistance durability were systematically investigated through orthogonal experiments, with the underlying micro-mechanisms revealed by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The results indicate that workability is predominantly governed by the water-to-binder ratio, while the micro-aggregate effect of FA significantly enhances fluidity. Mechanical properties are most significantly influenced by RM content; under a 20% CG aggregate replacement rate and a 0.45 water-to-binder ratio, an optimal compressive strength was achieved with a low content combination of RM and FA. Frost resistance deteriorated markedly with increasing RM and FA content, with the high-content group approaching the failure threshold after only 25 freeze–thaw cycles, occurring 50 and 125 cycles earlier than the medium- and low-content groups, respectively. Macro-micro results indicate a synergistic threshold at 20% red mud and 45% fly ash, yielding a compressive strength of 24.96 MPa. This value exceeds the 24.87 MPa of the 10% red mud + 45% fly ash group and the 21.90 MPa of the 10% red mud + 55% fly ash group. Microstructurally, this group also exhibits superior C-S-H gel uniformity and narrower crack widths compared to the others. Excessive incorporation of red mud and fly ash leads to agglomeration of unhydrated particles and increased porosity, aligning with the observed macroscopic strength degradation. This research identifies and quantifies the synergistic threshold governing RFCTSWC performance evolution, providing theoretical support for engineering applications of solid waste concrete. Full article