Search Results (30)

The performance analysis of a 10 kW_p rooftop grid connected solar photovoltaic (PV) system located in Sagolband, Imphal, India has been studied for 5 years. The key technical parameters such as array yield ($Y_A$), reference yield ($Y_R$), final yield ($Y_F$), capacity utilization factor (CUF), PV system efficiency (${\eta }_{Sys}$), and performance ratio (PR) were used to investigate its performance. In this study, the experimentally measured results of the system’s performance for the five years (i.e., July 2018 to June 2023) were compared with the predicted results, which were obtained using PVsyst V7.3.0 software. The measured energy generation in 5 years (including 40 days OFF due to inverter failure on 17 June 2019 because of a surge, which was resolved on 27 July 2019) was 58,911.3 kWh as compared to the predicted 77,769 kWh. The measured daily average energy yield was 3.2 kWh/kW_p as compared to the predicted 4.2 kWh/kW_p. It can be seen that there was a large difference between the real and predicted values, which may be due to inverter downtime, local environmental variables (e.g., lower-than-expected solar irradiation and temperature impacts), and the possible degradation of photovoltaic modules over time. The measured daily average PR of the system was 70.71%, and the maximum occurred in the months of October, November, December, and January, which was almost similar to the predicted result. The measured daily average CUF of the system was 13.36%, and the maximum occurred in the months of March, April, and May. The measured daily average system efficiency was 11.31%. Moreover, the actual payback was 4 years and 10 months, indicating strong financial viability despite the system’s estimated lifespan of 25 years. This study highlights the importance of regular maintenance, fault detection, and better predictive modelling for more accurate energy projections, and also offers an understanding of real-world performance fluctuations. Full article

The short-wave infrared (SWIR) grating imaging spectrometer based on indium gallium arsenide (InGaAs) material inverts the atmospheric methane concentration by measuring the scattered light signals in the sky. This study proposes spectral and radiometric calibration methods for the characteristics of the spectrometer, such as the small-area array, high signal-to-noise ratio, and high spectral resolution. Four spectral response function models, namely, the Gauss, Lorentz, Voigt and super-Gaussian models, were compared during spectral calibration. With a fitting residual of 0.032, the Gauss model was found to be the most suitable spectral response function for the spectrometer. Based on the spectral response function, the spectral range and spectral resolution of the spectrometer were determined to be 1592.4–1677.2 and 0.1867 nm, respectively. In addition, radiometric calibration of the spectrometer was achieved by combining an integrating sphere and linear measuring instrument. Moreover, absolute and relative radiometric calibrations of the spectrometer were performed. The low signal response problem caused by the quantum efficiency of the detector at long wavelength was corrected, and the uncertainty and non-stability uncertainty of absolute radiometric calibration were calculated to be less than 0.2%. Finally, the calibrated spectrometer was used to accurately measure the solar scattering spectrum in the SWIR band, and the solar spectrum was simulated by the radiative transfer model for verification; the measurement error was found to be 5%. Concurrently, a methane sample gas experiment was performed using the integrating-sphere light source, and the measurement error was less than 4%. This fully proves the effectiveness of the spectral and radiometric calibrations of the SWIR spectrometer and strongly guarantees a subsequent, rapid and accurate inversion of atmospheric methane concentration. Full article

We perform precise measurements of the ⁸⁷Rb Rydberg excitation spectrum by using electromagnetically induced transparency (EIT) in a ladder system. We utilize a two-photon excitation configuration with the probe and control lasers at 420 nm and 1013 nm, respectively. In this work, we employ $6P_{3/2},$F′ = 3 as an intermediate state to excite the high-lying Rydberg states of the $nS$ and $nD$ series, with principal quantum numbers ranging from $n=35$ to $n=70$. To improve the signal-to-noise ratio (SNR) in this inverted level scheme (${\lambda }_p<{\lambda }_c$), we apply a 100 kHz chopping to the control beam, which is followed by a demodulation operated with a lock-in amplifier. Additionally, we verify the ionization energies and determine the quantum defects for the $nS$ and $nD$ series, respectively. Our work offers a database for applications of large-scale quantum simulation and quantum computation with the ⁸⁷Rb atom array. Full article

Vs30, the average shear wave velocity in the uppermost 30 m, is a critical parameter in seismic hazard analysis. In the Philippines, the Refraction Microtremor (ReMi) survey is the standard method for Vs30 Estimation. This study evaluates the efficiency of using an elitist Genetic Algorithm (GA) to invert Horizontal-to-Vertical Spectral Ratio (HVSR) data as an alternative approach. Unlike ReMi surveys, which require geophone arrays, HVSR surveys use a single-unit three-component microtremor seismograph, enabling faster and broader data collection. Analysis of 174 HVSR and 52 ReMi datasets from the Greater Metro Manila Area (GMMA) and Leyte Province revealed strong correlations between estimated and measured Vs30 values. The overall match rates for soil profile classification under the National Structural Code of the Philippines (NSCP 2015) were 76% in GMMA and 81% in Leyte, with R-squared values of 0.885 and 0.806, respectively. Additionally, the relationship between the fundamental site period and estimated Vs30 values was explored. The R-squared values of 0.772 for GMMA and 0.707 for Leyte indicate a strong correlation and demonstrate the expected inverse relationship between the two variables. Given the Philippines’ high seismic activity, this method provides an efficient means to enhance seismic hazard mapping, improving earthquake preparedness and mitigation. Full article

This study analyzes the design, installation, and performance evaluation of a photovoltaic farm located in Tulcea County, Romania, connected to a 20 kV distribution network. With a peak capacity of approximately 2800 kWp, the farm takes advantage of Romania’s favorable climate conditions and the support provided by renewable energy policies. The analysis covers both the photovoltaic panel array and the electrical energy evacuation system. The substation at the park is equipped with technology that complies with European standards and integrates advanced features typical of modern distribution networks. The operational performance evaluation includes detailed calculations of the performance ratio and power losses, attributed to factors such as temperature fluctuations, panel fouling, inverter efficiency, grid-related issues, and system availability. The farm contributes around 3620 MWh of electricity to the grid annually, demonstrating the important role of photovoltaic installations in promoting sustainable energy solutions at the regional level. Full article

Several studies suggest that shale sweet spots are likely associated with a low Poisson’s ratio in the shale layer. Compared with conventional geophysical techniques with active seismic data, it is straightforward and cost-effective to delineate the distribution of 3D Poisson’s ratios using microseismic data. In this study, an alternating method is proposed to determine microseismic event locations, 3D P-wave velocity, and Poisson’s ratio models with data recorded from downhole monitoring arrays. The method combines the improved 3D traveltime tomography, which inverts P and S arrivals for 3D P-wave velocity and Poisson’s ratio structures simultaneously, and a 3D grid search approach for event locations in an iterative fashion. The traveltime tomography directly inverts the Poisson’s ratio structure instead of calculating the Poisson’s ratios from P- and S-wave velocities (i.e., Vp and Vs) that are inverted by conventional traveltime tomography separately. The synthetic results and analysis suggest that the proposed method recovers the true Poisson’s ratio model reasonably. Additionally, we apply the method to a field dataset, which indicates that it may help delineate the reservoir structure and identify potential shale sweet spots. Full article

This article presents an analysis of the performance of a 14.04 kWp grid-connected photovoltaic (PV) installation consisting of monocrystalline silicon, polycrystalline silicon and bifacial glass–glass monocrystalline silicon modules. The photovoltaic system was mounted in Poland, a location characterized by temperate climate conditions. On the basis of the obtained results, the photovoltaic parameters were determined in accordance with the international standard. The annual energy yield of the entire system was 1033 kWh/kWp, and the performance ratio achieved was 83%. The highest average daily final yield was in the range of 4.0–4.5 kWh/kWp for each photovoltaic technology under investigation. In the cold part of the year, the efficiency of the photovoltaic modules was estimated to be 15%, and it was estimated to be 7% during the warm part of the year. Array capture losses accounted for around 0.75 kWh/kWp of energy loss per day, whereas the inverter efficiency was over 95% during the months that are beneficial for energy production. Full article

Two-dimensional (2D) transition-metal dichalcogenides (TMDs) materials, such as molybdenum disulfide (MoS₂), stand out due to their atomically thin layered structure and exceptional electrical properties. Consequently, they could potentially become one of the main materials for future integrated high-performance logic circuits. However, the local back-gate-based MoS₂ transistors on a silicon substrate can lead to the degradation of electrical characteristics. This degradation is caused by the abnormal effect of gate sidewalls, leading to non-uniform field controllability. Therefore, the buried-gate-based MoS₂ transistors where the gate electrodes are embedded into the silicon substrate are fabricated. The several device parameters such as field-effect mobility, on/off current ratio, and breakdown voltage of gate dielectric are dramatically enhanced by field-effect mobility (from 0.166 to 1.08 cm²/V·s), on/off current ratio (from 4.90 × 10⁵ to 1.52 × 10⁷), and breakdown voltage (from 15.73 to 27.48 V) compared with a local back-gate-based MoS₂ transistor, respectively. Integrated logic circuits, including inverters, NAND, NOR, AND, and OR gates, were successfully fabricated by 2-inch wafer-scale through the integration of a buried-gate MoS₂ transistor array. Full article

In this paper, a twelve-antenna system is designed for 5G smartphones with metal frames. The system is compact and operates on dual bands within the sub-6 GHz frequency range using multiple-input multiple-output (MIMO) technology. Two sets of six-antenna units are included in the system, arranged in a diagonal mirror-image configuration, and positioned at the center of the circuit board’s longer edges. The profile height of each of the six-antenna units is only 3 mm, and the overall array dimensions are 105 × 3 × 3.1 mm³. A single antenna unit is 15 × 3 × 3.1 mm³ (0.173 λ × 0.035 λ × 0.036 λ, where λ equals the free-space wavelength of 3450 MHz). The arrangement of the antennas in the six-antenna units is parallel, with a 3 mm separation between adjacent antennas. The antenna structure comprises of an inverted L-shaped feed branch and two inverted L-shaped short-circuit branches integrated into part of the metal frame. The proposed array can form multiple resonance paths, achieving dual-band operation at 3300–3600 MHz and 4800–5000 MHz. The measured isolation of this twelve-antenna system within the operating frequency band is over 10 dB, and the measured antenna efficiency is greater than 36%. Therefore, the system is suitable for use in smartphones with high screen-to-body ratios and metal frames. Full article

Quality, reliability, and durability are the key features of photovoltaic (PV) solar system design, production, and operation. They are considered when manufacturing every cell and designing the entire system. Achieving these key features ensures that the PV solar system performs satisfactorily and offers years of trouble-free operation, even in adverse conditions. In each cell, the quality of the raw material should meet the quality standards. The fulfillment of the quality management system requires every part that goes into the PV solar system to undergo extensive testing in laboratories and environments to ensure it meets expectations. Hence, every MWh of electricity generated by the PV solar system is counted, the losses should be examined, and the PV system’s returns should be maximized. There are many types of losses in the PV solar system; these losses are identified and quantified based on knowledge and experience. They can be classified into two major blocks: optical and electrical losses. The optical losses include, but are not limited to, partial shading losses, far shading losses, near shading losses, incident angle modifier (IAM) losses, soiling losses, potential induced degradation (PID) losses, temperature losses, light-induced degradation (LID) losses, PV yearly degradation losses, array mismatch losses, and module quality losses. In addition, there are cable losses inside the PV solar power system, inverter losses, transformer losses, and transmission line losses. Thus, this work reviews the losses in the PV solar system in general and the 103 MWp grid-tied Al Quweira PV power plant/Aqaba, mainly using PVsyst software. The annual performance ratio (PR) is $79.5\%$, and the efficiency $\left(\eta \right)$ under standard test conditions (STC) is $16.49\%$. The normalized production is 4.64 kWh/kWp/day, the array loss is 1.69 kWh/kWp/day, and the system loss is 0.18 kWh/kWp/day. Understanding factors that impact the PV system production losses is the key to obtaining an accurate production estimation. It enhances the annual energy and yield generated from the power plant. This review benefits investors, energy professionals, manufacturers, installers, and project developers by allowing them to maximize energy generation from PV solar systems and increase the number of solar irradiation incidents on PV modules. Full article

Renewable power capacity sets records annually, driven by solar photovoltaic power, which accounts for more than half of all renewable power expansion in 2021. In this sense, photovoltaic system design must be correctly defined before system installation to generate the maximum quantity of energy at the lowest possible cost. The proposed study analyses the oversizing of the solar array vs. the capacity of the solar inverter, seeking low clipping losses in the inverter. A real 4.2 kWp residential PV installation was modelled and validated using the software SAM and input data from different sources, such as a weather station for weather conditions, ESIOS for electricity rates, and FusionSolar to obtain energy data from the PV installation. Once data were validated through SAM, the DC to AC ratio was varied between 0.9 and 2.1. The azimuth and slope sensitivity analyses were performed regarding clipping inverter losses. Results have been evaluated through the energy generated and the discounted payback period, showing that, depending on the weather conditions, slope, and azimuth, among others, it is advisable to increase the DC to AC ratio to values between 1.63 and 1.87, implying low discounted payback periods of about 8 to 9 years. In addition, it was observed that inverter clipping losses significantly vary depending on the defined azimuth and slope. Full article

Growing 5G/6G phased-array beam-steering applications, for which liquid crystal (LC) is one of the enabling technology candidates, have sparked interest in the modulation of the phase (and amplitude) of microwave and millimeter-wave signals. In this communication, fresh insights into the systematic design analysis of a 1–67 GHz passive inverted microstrip line (IMSL) phase shifter filled with highly anisotropic LC as tunable dielectric media are obtained. Based on waveguide disturbance tests to characterize the dielectric properties of the non-tunable PCB and tunable LC used in the IMSL phase shift device filled with a GT3-24002 LC layer (125 µm thick) partially enclosing a 220 µm wide, 17 µm thick, 1.35 cm long copper core line, a 0–π differential phase shift in the 1–67 GHz range with less than 2 dB insertion loss is reported. Dissipative loss analysis shows that the dielectric absorption of the LC is 21.28% of the input signal power at 60 GHz. Further investigation is performed to quantify the impacts of dielectric substrate thicknesses (PCB and LC) on the wave-occupied volume ratio (and hence the phase tuning range), as well as on dissipative losses (including conductor loss and dielectric loss). Specifically, conductor loss is observed to follow a linear relationship with the reciprocal of the LC thickness. Full article

Due to the full-wave AC–DC power conversion, second-order frequency oscillations of current and voltage are created in single-phase PV-grid-connected inverters. These oscillations propagate toward the input and adversely affect the PV power utilization ratio. Large power decoupling capacitors are the preliminary solution for coping with voltage ripples across PVs, and they decrease the lifetime of the overall system. This paper proposes the average current mode control (ACMC) of the input inductor in a DC–DC boost converter in a double-stage PV power conversion system. Through extensive explanations of the modeling and control of a DC–DC boost converter, it is shown that the ACMC reduces the propagation of the second-order frequency components (SOFCs) toward the input PV array. Two controllers—a proportional–integral controller and an integral single-lead controller—are considered to adjust the average value of the PV output current in a single-loop control structure. This control approach is simple to implement and exhibits high impedance to current oscillatory components, which, in turn, reduces the size of the required capacitance. Full article

The sustainability of new-generation energy sources has become one of the most critical challenges in recent years as renewable energy sources (RESs) rapidly replace old fossil sources. Integration between RESs and the grid should be completed through power electronics converters and optimized control techniques. RESs have many advantages, such as having increased reliability and sustainability, being environmentally friendly, and having cheaper maintenance costs and more reasonable energy prices. Photovoltaic (PV) panels are among the most popular RESs. A PV array’s generated voltage level is unsuitable for direct load or grid connection and has to be enhanced via a DC-DC boost converter. After that, an inverter should be used to change the generated DC voltage to AC voltage for the grid or loads. In order to reach higher voltage gains, different structures have been proposed in the literature, such as cascaded converters, non-isolated converters (including transformers), and positive- and negative-voltage-lift Luo converters. These converters have some disadvantages, such as including a large number of semiconductor devices and inductors, heavy and bulky structures, and the need for intermediate converters to convert DC to AC voltage and vice versa. Besides the efficiency and high DC voltage gain feature, to achieve more reliability and sustainability and a longer lifetime of the PV source, the current drawn from these sources should be as ripple-free as possible. This study considers all these details by presenting a novel DC-DC power boost converter. The steady-state analysis, simulation, and test results are presented. The most important features of the proposed converter include the lack of need for a transformer, intermediate inverter, rectifier converters, and bulky and heavy components, while still ensuring that high voltage gains and high efficiencies are possible. Simulation results showed that for duty ratios from D = 0.05 to D = 0.15 for the switch S3, the gain of the converter was 22, 35, and 70 times greater than the input voltage, respectively. The desired 200 VDC and 400 VDC voltages for the output nodes were obtained using 12 VDC as the input voltage with and without the switched-capacitor cell, respectively. A limited number of the voltages between −47 and 12 V dropped across the inductors, and a reversed voltage from −12 to −48 V was reported for the power diodes. Additionally, an efficiency close to 96.88% was obtained for the proposed converter. According to the experimental results, a voltage close to 198 VDC was obtained with a 12 VDC input voltage source without using the switched-capacitor cell. A current with a maximum of 7 A was reported for the output diode, and more than 96% efficiency was reported. The results showed that the primary source of the power losses was the semiconductors, and the switching losses made up around 69% and 88% of the total losses for the switches and diodes, respectively. The present topology has three power switches. Two of the switches are activated and deactivated simultaneously. The third switch is activated or deactivated in reverse with the other switches. The results showed that for short-duty ratios such as 0.5 for switches S1 and S2 and 0.35 for switch S3, DC voltage gains close to 35 were obtained theoretically. The generated voltage could be doubled by applying fourth and fifth power switches by making a switched-capacitor-based topology. All of these details are illustrated in this study in detail. The proposed circuit was set up and tested in a laboratory environment. The test results confirm the simulation and theoretical analysis. Full article

Red Malus ‘Royalty’ fruits are rich in anthocyanins. This study aimed to obtain the optimal parameters for the extraction and separation of anthocyanins from Malus ‘Royalty’ fruits and to evaluate the inhibitory effect of the enriched anthocyanin fraction on gastric cancer cells. Ultrasonic-assisted extraction was used for the extraction of the anthocyanins of Malus ‘Royalty’ fruit, and the extraction results showed that the optimum parameters were an extraction temperature of 20 °C, a solid–liquid ratio of 1:6 (g/mL), ethanol and formic acid contents of 70% and 0.4%, respectively, an extraction time of 40 min, and an ultrasonic power of 300 W. The optimum extraction parameters to achieve the highest anthocyanin yield by a single-factor experiment coupled with response surface methodology were identified. The separation results showed that the AB-8 macroporous resin was a better purifying material, with 60% ethanol as an adsorbent, and the adsorption–desorption equilibrium times were 6 h and 1 h, respectively. Cyanidin-3-galactoside was the main body composition separation of anthocyanins by a high-performance liquid chromatography-diode array detector. The antitumor activity results showed that the anthocyanins of Malus ‘Royalty’ fruits have a significant inhibitory effect on the gastric cancer cell line BGC-803. The in vitro cell viability test of CCK-8 showed that the inhibitory effect on tumor cells was more significant with the increased anthocyanin concentration, with a half maximal inhibitory concentration (IC₅₀) value of 105.5 μg/mL. The cell morphology was observed by an inverted microscope, and it was found that the backbone of BGC-803 treated with a high concentration of anthocyanins was disintegrated and the nucleoplasm was concentrated. The mechanism of apoptosis was analyzed by Western blotting, and the results showed that with increasing anthocyanin concentration in the medium, the expression levels of the proapoptotic proteins Bax and Bak increased, and the expression levels of the antiapoptotic proteins Bcl-2 and Bcl-xL decreased, which coordinated the regulation of cell apoptosis. This research suggests that the enriched anthocyanin fraction from Malus ‘Royalty’ fruits have potential antitumor and adjuvant therapeutic effects on gastric cancer. Full article