Why Does the PV Solar Power Plant Operate Ineffectively?

: Quality, reliability, and durability are the key features of photovoltaic (PV) solar system design, production, and operation. They are considered when manufacturing every cell and designing the entire system. Achieving these key features ensures that the PV solar system performs satisfactorily and offers years of trouble-free operation, even in adverse conditions. In each cell, the quality of the raw material should meet the quality standards. The fulﬁllment of the quality management system requires every part that goes into the PV solar system to undergo extensive testing in laboratories and environments to ensure it meets expectations. Hence, every MWh of electricity generated by the PV solar system is counted, the losses should be examined, and the PV system’s returns should be maximized. There are many types of losses in the PV solar system; these losses are identiﬁed and quantiﬁed based on knowledge and experience. They can be classiﬁed into two major blocks: optical and electrical losses. The optical losses include, but are not limited to, partial shading losses, far shading losses, near shading losses, incident angle modiﬁer (IAM) losses, soiling losses, potential induced degradation (PID) losses, temperature losses, light-induced degradation (LID) losses, PV yearly degradation losses, array mismatch losses, and module quality losses. In addition, there are cable losses inside the PV solar power system, inverter losses, transformer losses, and transmission line losses. Thus, this work reviews the losses in the PV solar system in general and the 103 MWp grid-tied Al Quweira PV power plant/Aqaba, mainly using PVsyst software. The annual performance ratio (PR) is 79.5%, and the efﬁciency ( η ) under standard test conditions (STC) is 16.49%. The normalized production is 4.64 kWh/kWp/day, the array loss is 1.69 kWh/kWp/day, and the system loss is 0.18 kWh/kWp/day. Understanding factors that impact the PV system production losses is the key to obtaining an accurate production estimation. It enhances the annual energy and yield generated from the power plant. This review beneﬁts investors, energy professionals, manufacturers, installers, and project developers by allowing them to maximize energy generation from PV solar systems and increase the number of solar irradiation incidents on PV modules.


Introduction
Electrical companies strive to exploit renewable energy's vast potential to meet the growing energy requirements.The high penetration of photovoltaic (PV) power plants in electrical generation is evident due to the global increase in their installation capacity year-by-year, as shown in Figures 1 and 2, respectively.Plummeting prices and the rising efficiency of the plant enhance the installed capacity.At the end of 2021, the total installed capacity was around 947 GW, as shown in Figure 3.
New technologies tend to come with unknown risks; investors must know these.Every technology brings a new mode of failure and a unique design.The solar system's efficiency should be calculated under standard test conditions (STC).The STC are the industry standards for conditions under which solar panels are tested using a fixed set of conditions.Thus, the solar panels can be more accurately compared and rated against each other.The STC are specified as a temperature of 25 • C for the cell itself, not the surrounding ambient temperature, and an irradiance of 1000 W/m 2 .This refers to the amount of energy falling on a given area at a given time.Additionally, the air mass (AM) under the STC is 1.5.PV solar power plants have had the most significant generation growth among renewable energy resources globally.They exceeded 1000 terawatt-hours (TWh) by the end of 2021.Records show that the increment was 179 TWh that year, as shown in Figure 6.This has become the lowest-cost option for new electricity generation installations for most of the world.The average annual growth was 25% in 2022-2030 [28].A strategic policy and tremendous effort from the public and private sectors must be established to achieve a net zero emissions scenario by 2050.PV solar power plants account for 3.6% of global electricity generation and remain the third-largest renewable electricity technology after wind energy and hydropower generation.In 2021, China was responsible for about 38% of the generation growth as it installed a large PV solar power plant capacity.The USA had the second-largest generation growth, about 17%, and the European Union had the third-largest 10%.As a result of this strong growth, experts have amended their outlook for 2022, anticipating new systems to total between 204 and 252 [28].This paper is organized as follows.Section 2 presents the current status of renewable energy in Jordan.In Section 3, PV power plant optical losses are explained.Next, PV power plant electrical losses are investigated in Section 4, followed by optimization of the PV solar power plant design in Section 5. A real case study is analyzed in Section 6.The results and discussion are presented in Section 7. Finally, the conclusions are mentioned in Section 8.

Current Status of Renewable Energy in Jordan
Jordan is one of the world's most energy-insecure countries, importing 96% of its energy needs.The energy challenge in Jordan is more critical today than ever; this is why the government of Jordan has issued an energy efficiency and renewable energy law which provides incentives for sustainable energy solutions.The government ambitiously aims to slash its fossil fuel bill by making green energy 20% of its overall power consumption by 2024.Jordan has become aware of the importance of solar power for reducing energy costs.Jordan is blessed with over 300 days of sunshine yearly and is considered one of the sunbelt countries.Unsurprisingly, solar energy projects have quickly become the government's hot choice.A legal framework has been developed in Jordan to attract investors and the government's commitment to renewable energy.Thus, the Kingdom has officially made its place on the renewable energy map.In 2012, Jordan encouraged the installation of solar cells in houses, enabling consumers to store or buy the solar energy surplus.In 2018, investments in solar energy amounted to 30 fully implemented and under-construction projects.The actual investment amounted to $1.938 [29] billion.Most solar energy projects are located in the south, where there is higher solar radiation, making this sector a promising investment opportunity.Thus, it is expected that there will be an increase in the reliance on solar energy in Jordan in the coming years.Therefore, as a case study, this review investigates the state-of-the-art research on losses in PV power plants in general and in Jordan's Quweira PV power plant in particular.Jordan's Ministry of Energy and Minerals Resources (MEMR) is the project owner of the Quweira PV power plant, and Tsk-Enviromena JV is the project contractor.At the Jordanian transmission network at the National Electric Power Company (NEPCO), the Al-Quweira PV solar system is integrated at the 132/33 kV substation via two step-up transformers.Table 1 shows generated power stations connected to transmission lines (MW) based on the fuel used.Table 2 shows renewable energy projects connected to the transmission system in 2020.Table 3 shows the electrical energy (GWh) consumed based on fuel used.Investigating losses leads to less expensive and more efficient PV solar power modules that can easily be installed.Solar panel affordability and efficiency have improved dramatically over previous decades.Researchers are continuously looking at improving the efficiency rate of PV to make the most of solar power.Hence, massive competition in the solar power market is expected to lead to lower prices for solar panels and more efficient storage solutions [30].Table 2. Renewable energy projects connected to the transmission system in 2020 in Jordan [29].

Project Generation Capacity (MW)
Mass Group Holding Ltd/Tafila

Optical Losses
Optical losses in a PV power plant can be analyzed based on shading losses, spectral mismatch, thermalization, nanoabsorption, reflection, parasitic absorption, and additional losses.

Partial Shading Losses
In shading effects, wherein a shadow falls across a module section, it causes the electrical energy of at least one or more strings of cells in the module to fall to zero, but the entire module's output does not fall to zero [31].A PV cell is an electrical device that directly converts light energy through the PV effect.PV cells have a complicated relationship between solar irradiation, temperature, and total resistance and exhibit a nonlinear characteristic curve known as the P-V curve [32].
Figure 7 shows a PV array with bypass diodes across each module and blocking diodes at the top of each string.If one of the panels is shaded, it acts as a high resistance and blocks the flow of power produced out of the panel itself and the power produced by the unshaded panel.Hence, a bypass diode comes into play; the current created by the unshaded panel can flow through a bypass diode to avoid the high resistance of the shaded panel.Bypass diodes are not used unless panels are connected in series to generate a higher voltage.Some solar panels are assembled with the cells divided into groups, each with a built-in bypass diode.When the sun shines, the voltage generated by the two panels is more than that of the battery.However, in the dark, the panels produce no voltage [33].Thus, the voltage would cause a current to pass in the opposite direction through the panels.Hence, blocking diodes prevent the discharge of the battery.Blocking diodes are usually involved in the construction of solar panels.Thus, bypass diodes protect the panels and prevent hot spots in shaded cells connected in series, whereas blocking diodes prevent the reverse current drawn by shaded string [34].

Top methods in this publication
Partial shading can dramatically reduce the power output of a PV array as well as complicate operation by causing multiple p appear in the power-voltage P V characteristic curve.The extent of these problems depends not only on the shading area much more significantly on the shading pattern.In this paper three new physical PV array arrangements are proposed to mit shading effects.The arrangements are based on maximizing the distance between adjacent PV modules within a PV array b arranging modules in different rows and columns without changing the electrical connections.A systematic analysis is perfo assess the proposed PV array arrangements under different shading patterns and scenarios, and to compare performance w configurations.The new arrangements are shown to effectively (i) redistribute shading patterns over the entire PV array, (ii) protection diodes power dissipation, (iii) eliminate multiple peaks, and (iv) maximize power output.The analysis considers sh scenarios related to cloud shape, size, transmissivity and passage over an array.The new configurations simplify operation a performance significantly compared to the reference Series-Parallel SP and Total Cross Tied TCT configurations: the cha curves exhibit a single peak allowing tracking of the maximum power point with a simple controller removing the need for co controller algorithms and costly hardware, and the power output gains range from 19 to 140% compared to SP, and 13 to 68% TCT.
This figure was uploaded Djilali Content may be subject t copyright.Figure 3 Impact of bypass diode on the I V PV characteristic of two PV modules connected in series.

Far Shading Losses
When the PV array has an elevated horizon, for example, from a nearby mountain range, newly built high skyscrapers, or even city skylines, these objects blackface the sunlight received by the PV array.In such cases, shading from the horizon is applied to the entire PV plant.This happens during the hours in which the sun is below the horizon line.At that time, the array loses its direct irradiance.The energy generated is only based on diffuse solar irradiance.In such events, a solar PV array starts to lose solar irradiance, because Mega objects, such as skyscrapers, are located nearby, from 5 to 15 km.Such losses in a PV plant are known as far shading losses.The designer can model these losses in the PV system by accessing that location's horizon profile through a simulation.Tools like the Solmetric SunEye or Solar Pathfinder can generate horizon profiles.The Solmetric SunEye is a digital handheld instrument that can be easily carried and used at any project site to capture a far shading profile [35].
In comparison, after capturing the shading profile from the installation site with Solar Pathfinder software, the operator can easily import the shading profile into the system for further analysis.Indeed, the Suneye and Solar Pathfinder are equally efficient and accurate for far shading analysis.Meteonorm and Aurora Solar software can also create the horizon profile remotely based on the online contour mapping facility.Any horizon file that lists the azimuth and elevation angles can model a horizon profile.The line at the bottom of this file is caused by far shading and interpolating linearly.There are two options [36]:

•
Losses ≤| 1 | % consider the project site, obtain the horizon profile, and analyze the amount of far shading loss annually.

•
Losses ≥| 1 | % consider changes in the project site, discard the proposed site, or raise the alarm to the management about such losses.
Far shading loss assessment is essential for the proposed project site, as are other parameters, such as cost-effectiveness and accessibility to the local electricity grid [37].Thus, this impacts the techno-commercial characteristics and long-term economic assessment.Thus, mitigating or optimizing far shading loss is primarily the decision of the project designer.

Near Shading Losses
These losses occur because of shadows on the solar panel from the objects near it.They can be categorized as

1.
Nearby buildings, trees, electric poles, and headlines may create shadows on the PV and rooftop installations, such as service areas, water tanks, satellites, and air conditioning chillers.Shade from these obstacles can substantially decrease the PV power plant's output.Thus, it is recommended that such areas are avoided for installations.

2.
Nearby transmission lines passing by the PV site or within the PV power plant can cause shading on the PV module.Similarly, nearby wind turbines may cause a shadow on PV arrays.Shading decreases the total electricity production of PV panels and can create a thermal hotspot, resulting in long-term degradation.Some research states that these shadows cause junction diode failures and fire hazards.Fire accidents can happen in PV installation.More than 80% of these accidents are due to partial shading [38].Commercially, the manufacturer provides a product and performance warranty for 25 years to 30 years.If the solar panels are installed in the shaded area, the contractual agreement of the module warranty is lost.Figure 8 shows components in which a fire occurred in a PV plant.Table 4 illustrates the potential hazards for firefighters working close to a PV power plant.Table 4. Illustration of potential hazards for firefighters working close to PV power plants [39].

Potential Hazard Illustration
Electrical shock Contacting an energized conductor on an energized module or broken energized modules or exposed wires.

Slips and falls
Space limitation.

Collapse
The roof may collapse when support beams are weakened.
Arc or ground fault An arc may occur from exposed conductors in an energized PV power plant.
Combustion Materials in the PV power plant may be burnt and release noxious gases.
• Inter-raw shading The insufficient space between the top edges of two mounted strings leads to inter-raw shading.Thus, a specified distance should be kept between the two rows and the tilt angle should be optimized.Hence, an optimized ground coverage ratio (GCR) value should be considered.The GCR is defined as the ratio of the solar The GCR provides the percentage of an area that can be utilized for the PV power plant's installation: the higher the GCR value, the lower the PV capacity.On the other hand, a lower GCR means that the inter-raw pitch is increased, the shading loss is decreased, and the specific PV power plant output is increased.

•
Hotspots occur due to junction diode failure; fires may even happen.Finally, an annual near shading loss of up to | 2 | % is an acceptable limit [40].

Incidence Angle Modifier (IAM) Losses
A portion of sunlight is reflected when it strikes the PV module's surface.The reflection is more significant when the sunlight's incident angle is high.This reflection loss is technically called the IAM.The PV module consists of different layers, as shown in Figure 9.When sun rays fall on the glass, a portion of the light is transmitted through the layers based on the theory of reflection-Fresnel's law.If light falls on the glass surface at 90 • , then the reflection is less than 5% [41].
On the other hand, the reflection is low at a low incidence angle.The IAM applies to both direct and diffuse irradiance.Additionally, solar irradiance is very low during sunrise or sunset.IAM is calculated for each PV module in the array.When the angle of incidence increases, subsequently, the loss effect increases.After 50 • , the loss starts to grow exponentially [42].The incidence angle is inversely proportional to the solar azimuth angle.The solution is obtained using the PV modules' antireflective coating (ARC).The ARC entraps sunlight in a particular medium.Thus, the losses are limited to (2-3%) of the yearly energy yield.Both the glass coating and PV cell surface are manufactured, including the ARC, to reduce the IAM loss.Selecting materials with a high dielectric strength and a specific thickness for ARC film allows most of the sunlight's bandwidth to be absorbed.Figure 10 shows how PV cells with ARC operate highly efficiently through the various spectra of the sunlight's wavelength.Major manufacturers provide ARC under standard conditions for all PV modules [43].The IAM optical loss factor is given by Equation (2) [45]: where τ is the weighted transmittance, R is the weighted reflectance, and A is the absorbance.The weight of the IAM loss factor is calculated using the spectral distribution of radiation and the PV module spectrum response.The basic approach for describing the IAM was developed by Souka and Safat in 1966 [45].The American Society of heating, refrigeration, and air conditioning (ASHRAE) developed the model.The new model is given by Equation (3) [46].
where AOI is the angle of incidence.Equation (3) has a discontinuity problem at θ AOI = 90, whereby it is inaccurate at low incident angles [46].Another IAM model was adopted in 2006 by De Soto, based on Snell's and Bougher's law.In this model, the angle of reflection (θ r ) is given by Equation ( 17) [47]: where l is the index of reflection of the air, n is the index of reflection of the cover glass, and θ is the angle of IAM.I AM B is given as shown in Equation ( 18) [47]: Energies 2023, 16, 4074 10 of 38 where τ(θ) is the transmittance at angle θ and τ(0) is the transmittance normal to the sun.τ(θ) and τ(0) are given by Equations ( 6) and (7), respectively [47].
Additionally, there are Sandia IAM models that describe these losses as a 5th-order polynomial [48] and the Martin and Ruiz IAM model [49][50][51].

Soiling Losses
These are caused by the accumulation of snow, dirt, dust, leaves, pollen, and bird droppings on PV panels.Thus, the accumulation of soil on the PV module can lead to a significant decrease in energy production by the PV module [52,53].The amount of sunlight blocked by dirt and debris accumulates on the solar panels over time.Soiling losses are not constant throughout the year.They depend on weather and season changes.The driving factors for the soiling losses are as follows [54]:

•
Locations vary from region to region.The soiling loss profile differs between Europe and the gulf region.There are more dust particles in the gulf region air than in other places due to the deserts.• Air pollution is not the same everywhere.It is near industrial, dense urban, and corp land.In the agricultural area and during the season of corp harvesting, the soiling rate increases rapidly.However, for the rest of the year, it remains deficient.The percentage loss due to dust decomposition is higher than in other places, especially in suburban areas where many public and private means of transport move around on the road daily.• Air mist: A higher moisture content makes dust stick to surfaces.Thus, the dust remains stuck to the surface, even with heavy wind.• Bird droppings: Forced cleaning is required to remove the deposition.This represents a severe problem; the rain does not remove them.Nevertheless, their reported impact is relatively small ≤2% in terms of the total soiling loss.• Snow: Heavy snowfall covers entire PV arrays.The whole modules are cut off from sunlight, and there is no electricity production.However, if the module surface is partially covered by snow, it is hazardous, as it causes electrical damage to the PV module.
The soiling loss (SL) values observed from many solar plants throughout the world in recent years are as follows [55]: % if the region is near major vehicular traffic areas.• 0.5% if the system is cleaned in summer.
The solutions to reducing the soiling loss are as follows [4]: • Clean the PV surface regularly with a 15-30 day cycle for large systems and every 60-90 days for small rooftops.

•
Table 5 shows different cleaning methods used in PV solar systems.

•
Higher tilt angles help to remove dust naturally.It is recommended that the tilt angle is low for installation.The tilt angle depends on the location and time of the year [56].
Self-cleaning Electric charge, surface covered with a pellucid nanofilm.
The average number of days between cleaning events (n) in the PV power plant is given in Equation ( 8) [58]: where C optimum is the optimal number of cleaning cycles, and the increment of S loss per day is known as the soiling rate (SR).For instance, a SR of 0.2%/day means that the S loss is 0.2% for the first day.Then, it increases to 0.4% and 0.6% for the second and third days, respectively, and so on.Thus, the S loss is given by Equation ( 9) [58].
where k is the number of days with no cleaning.The annual yield loss Y loss is given as shown in Equation ( 10) [58].
where C is the installed capacity of the PV power plant, and Y spec is the specific annual yield.

Potential Induced Degradation (PID) Losses
The solar panel consists of individual PV cells.Each of these cells generates electricity from the collected sunlight.These solar cells are large photodiodes where the charge currents are separated due to the PN junction's electric field.The incident sunlight dislodges electrons.These electrons then flow along with the contacts and generate green electricity.The grounded PV array has a string or array grounding, so the potential across the system always remains positive to the Earth.PID does not occur in grounded systems, where the inverter's negative pole is grounded, or in systems less than or equal to 600 V. Here, eliminating the high negative voltage potential drives the PID phenomena.Thus, the potential can float between high positive or negative values in an ungrounded PV array.The high voltage difference across the solar module structure is responsible for degradation.Due to the high negative potential to the Earth, sodium ions from glass are ionized and drift toward the solar cell.These Na + .ions penetrate through the arc layer to the emitter layer of the solar cell, and electrons captured by Na + ions become Na.The high relative voltage forces the sodium ions to diffuse from the glass through encapsulation and eventually accumulate on the cell surface.Modules with negative potential concerning the ground are mostly affected.
The PID affects panels closer to the string's negative side.The negative potential concerning the Earth is the highest on that side.In an individual PV module, the PID effect is more potent in cells closer to the aluminum frame, whereas it is less effective in cells in the center of the modules.Figure 11 shows that the PID affects solar modules near the negative string more.Currently, the system level exists due to higher string voltage designs, such as those with up to 1500 V, which can create a very high potential difference and a transformerless inverter (floating potential) [8].This process creates a stacking fault through the solar cell.It happens at the microcrack surface, increasing recombination and reducing the power output-the propagation of microcracks when walking on a PV module.When the mechanical load is released, these cracks become invisible.The occurrence of microcracks reduce the performance and causes a direct financial loss.These cracks also occur during transportation, installation, and operation.Most breakage locations that occur during module design and construction after mechanical stress tests are located in the module's center.It is due to being the area of the highest mechanical tension and stress by bowing [60,61].
Power reduction caused by the PID may happen gradually over time or immediately after installation.Power loss ∆P is proportional to current loss through the equivalent PV cell circuit shunt.PID is responsible for power losses of up to 30%.This mechanism has become very important due to the high PV voltage rating.PID can affect the modules within a few years and decrease the PV modules' output power.More work has been done on developing a PID sensor to detect PID before a 1% power loss occurs.The detection device's operation is based on the electrical quantity, which is easy to measure.Usually, the installation site's modules are removed and tested indoors.This action is considered time-consuming and costly and causes damage to the modules.Yield and efficiency are lost in a PV power system every day.The result is a dramatic loss of earnings within a short period of time.Polarization and leakage currents in the module cause these losses.Solar cells become inactive.Finding a PID killer increases the PV array to a highly positive potential and reversing the polarization effect is considered an open research problem.In a few months or years, the performance could deteriorate by 30% to 40% or more.PID accelerates performance degradation, which grows exponentially.An early detection mechanism for PID is essential, because it allows for some reversal of that effect.Prevention is always preferable to treatment.According to Finsterle, PID lowers the open-circuit voltage (V oc ) and the module's maximum power point (MPP) [62].
PID is considered one of the crucial factors associated with PV reliability.PID testing comprises a 96-hour test period, during which test panels are subjected to humidity and temperature levels of 85% (±5%) and 60 • C (±2 • C), respectively.The voltages applied to these panels may correspond to the maximum plant voltage listed in the panel datasheet.The IV measurement is visually inspected as part of the PID testing method.The module must pass the test without significant defects and with a power loss not exceeding 5%.PID increases the probability of not guaranteeing a 25-year warranty life.Additionally, high humidities and temperatures cause more significant overall losses.At an early stage, PID can be reversed by changing the voltage bias.PID is not detectable to the naked eye.Tests can be used to sense PID in operational sites such as thermal images, electroluminescence, and IV curves.PID can be prevented using strings with isolation transformers between the strings and the inverters, negative terminal grounding, and installation of the anti-PID [62].

Temperature Losses
A fraction of solar cell radiation produces electricity, and the remaining radiation is converted into thermal energy.A portion of the produced thermal energy increases the solar cell's temperature, dissipating the rest from the top and bottom of the cell.The temperature of the cell determines its electrical performance.Hence, the IV curve in the PV module at a given irradiance states that the power output decreases when the temperature increases and there is a voltage drop.In comparison, the PV solar output power is increased when the temperature falls while the irradiance remains constant [11].Conveniently, a semiconductor demonstrates better conductivity with an increasing temperature, and at zero Kelvin, it acts as an insulator.This can be explained by Equation (11).The net effect of temperature is linearly related to the open-circuit voltage V oc , while the temperature is associated with the rise in the photodiode's leakage currents.The cells with lower V oc are more affected by temperature than cells with higher V oc .This implies that a solar cell based on crystalline silicon with V oc of 650 mV is more affected than an amorphous silicon solar cell with an V oc of 850 mV [63,64] .
Fabrication of the PV module includes the temperature coefficients in the commercial modules' datasheet.The temperature coefficient of power is the rate of change in the output power concerning the temperature.Likewise, the temperature coefficient is the rate of change in a voltage concerning temperature.A typical datasheet of a commercial module specifies temperature coefficients for the I sc , V oc , and power under STC.Equation (12) shows how to calculate the PV power output concerning the temperature change dP dT .The reference temperature 25 • C is considered to be the STC temperature [63].
The operator should distinguish between the module temperature and ambient temperature.The difference in heat flow in and out of the module's encapsulation solar cells is affected by various factors.The primary factor involved in increasing the PV module's operating temperature is the thermal equilibrium between the heat lost to the surrounding environment and the PV module's heat.Heat exchange with the surroundings depends on the heat transfer coefficient of the module and its surface area, wind speed, and ambient temperature.The conductive heat loss is caused by heat flow from one material to another.The NOCT model is expressed in Equation ( 13), where the cell temperature depends on the irradiance and the ambient temperature [65].Thus, the cell temperature never goes below the ambient temperature, and the minimum limit is at the ambient temperature.It takes place at night when the irradiance is zero.The NOCT of a particular PV module depends on the nominal wind speed of 1 m/s, an ambient temperature of 20 • C, the PV cell under an irradiance of 800 W/m 2 , and the no-load conditions (η c = 0).The performance of the module is worse due to the temperature effects that drop the PV output power at high cell temperatures while the sun shines in summer [63,66].
In addition, the energy balance is given in Equation ( 14) [63,66]: where τ is the transmissivity of the cover of the solar cell, α is the absorptivity of the solar cell, η c is the electrical efficiency, I(t) is the PV output current (A), U L is the overall loss coefficient, and T cell is the solar cell temperature.For no-load conditions, η c = 0. Thus, Equation ( 14) can be rewritten as Equation ( 15) [63,66].
Thus, the cell temperature can be found with Equation ( 16)

Light-Induced Degradation (LID) Losses
Some modules experience a permanent blackout in power output upon initial exposure to light.Thus, the efficiency is reduced.The degradation ranges from 1% up to 5%.Hence, LID phenomena play an essential role in manufacturing a-Si-based solar panels.Amorphous silicon (a-Si) has been the best-developed thin-film material in commercial production since 1980.It is an inexpensive material [67].Its amorphous nature has several significant consequences for PV.Here, the shedding light's absorption is acceptable, but doping and charging transportation are difficult.
In 1977, it was discovered by Staebler-Wronski that there are dangling bonds of different lengths and orientations in amorphous silicon (Si) materials.When the conductivity of a-Si is exposed to light for a specific period of time, the conductivity drops to a certain level based on the a-Si phenomenon.There are many models to explain this observed behavior.One of these models is the hydrogen bond switching model.This model supposes that the silicon items are bonded in the a-Si.When light shines on this material, electrons are generated in whole pairs.These electrons and hole pairs are virtually connected.They can recombine and release a photon from the bond.This energy breaks the bond and releases the energy.This is essential to create the dangling bond on these silicon atoms.Briefly, this model states that this bond is essentially switched by hydrogen.This hydrogen is present in a-Si materials.The bonds between the two silicon atoms and hydrogen represent H-bond switching.The dangling bond's density increases as light shines, because of the recombination of these electron and hole pairs that are generated as a consequence, as well as due to the creation of dangling bond states [10].Another model is the hydrogen-collision model.In this model, dangling bonds are created in these amorphous materials.Silicon items are bonded to hydrogen.When light shines, it causes these bonds to break, creating dangling bonds on each silicon atom.The hydrogen is subsequently set free and released [68].

PV Yearly Degradation Losses
The PV module's performance is generally rated under STC: an irradiance of 1000 W/m 2 , a solar spectrum of AM 1.5, and a module temperature at 25 • C. The module's actual V PV and I PV change as the lighting temperature and load conditions change.The module's performance depends on the time delay, solar installation, direction and tilt modules, cloud cover, shading, temperature, geographic location, and day.The voltage and current fluctuations are logged with a multimeter or data logger.More complex and high-efficiency technologies have higher potential for degradation.Figure 13 shows the drop in the plant's output capacity for three annual degradation cases.Three key factors were used as the selection criteria: reliability, technology selection, and the levelized cost of electricity (LCOE).Technology selection depends on the insulation, temperature, precipitation, and geography.The module's performance was simulated based on actual weather data.LCOE describes the cost of power produced by a PV power plant over time, typically the plant's warranted life.The most significant impact of LCOE is the cost of PV modules, as they constitute the central part of the plant.Many factors impact the LCOE cost, such as the module price, the power generated by a module over its warranted life, and the power degradation during a module's lifetime [12].

Figures and Tables from this paper
Figures and Tables The long-term performance of solar modules is of key importance to achieve pro table solar power installations.In this work, the degradation mechanism potential-induced degradation (PID) was inve ...

Array Mismatch Losses
Array mismatch losses occur when solar panels of different wattages and voltages or manufactured by different companies are mixed.However, these are not recommended or prohibited.In this case, particular interest should be given to each panel's electrical parameters.When two panels from different vendors are connected, the problem is that they have different electrical characteristics and, thus, various degradation performances.Wiring mismatched solar panels together negatively impacts the solar output power.Operators should take a look at the parameters on both panels.Therefore, a datasheet is available on the back of the panels; the operator should pay more attention to V oc , V mp , I sc , and I mp .The ideal cell would have a perfect rectangular characteristic, and the closeness of the characteristics to the rectangular shape is a measure of the cell's quality.The solar cell's output power increases with solar radiation.The I sc changes are essentially proportional to the change in solar radiation.However, the voltage difference is comparatively less.However, there are a few drawbacks.The operators should use the maximum power point (MPPT) and charge controller to absorb the excess voltage and bring it down to the battery bank [70,71].
The least-rated power module determines the overall rated current in solar modules connected in series and drags the overall plant output down.The overall voltage should not exceed the maximum voltage limit of the MPPT charge controller connected to the modules [72,73].While modules connected in parallel obtain a high current, the voltage is the lowest with parallel connections.The current in a series connection and the voltage in a parallel connection decrease the solar array's performance.Reducing the current or reducing the voltage of one of the panels reduces the power output, therefore causing a reduction in the system's performance.Hence, wiring mismatched solar panels together negatively impact the solar power output.As the operator adds many panels, the wire size should be increased [13,14].In some cases, the underperformance of a module could have a cause as small as a crack in the module, the soiling conditions, or the presence of some hydraulic fluid in the construction process, all of which have the same effect as the mismatched module [74].

Module Quality Losses
Understanding the quality of PV components and translating this information into actionable results is more important than ever.A healthy PV power plant mainly depends on the reliability of its components.Hence, the module's quality depends on performance and safety issues associated with its assets.The detection of module degradation is based on many issues, such as thermal anomalies, often giving modules a sense of power loss.This information is combined with electrical factors at the string or panel levels, giving further information about gradual losses in historical power data analysis.Historical degradation by inspecting the power data is considered an important issue.It can shed light on quantitative historical losses and trends.Combining this visual inspection and laboratory analysis can determine and confirm the nature of degradation and safety risks.IV measurements can quantify gradual losses compared with power nameplates.Each year, amassed field inspection information and data are gathered and analyzed [75,76].
Defect modules can be classified into cell and interconnection types, such as corrosion, hot spots, snail trails, broken interconnections, cracks, and burn marks.Additionally, a back sheet includes the outer layer (airside) and the inner layer (cell side), cracking, delamination, and yellowing.Encapsulants include discoloration, browning, and delamination.Different defects include glass defects, a loss of the antireflection coating (ARC), and junction boxes.The long-term performance is affected by field failures.Many modules may not be able to last 20-30 years.Statistics show an increment in the field's frequency and extent of module and plant failures.All modules are not created equal in terms of new cells, technologies, and materials.They support the worldwide PV community by generating data that accelerates solar technology adoption.Quality testing shows many common solar panel defects, such as scratches and uneven or excessive glue on glass and frames.Unsealing problems exist, such as gaps between the glass and the frame.Thus, the output or fill factor is lower than stated in the datasheet, and the cell colors and alignments are inconsistent.Figure 14 shows some of the PV modules' quality losses [77].

Electrical Losses
Electrical losses in PV solar systems include cable, inverter, transformer, and transmission line losses.These losses can also be classified as DC plant losses, AC plant losses, and DC to AC conversion losses.

DC & AC Cable Losses
Most solar power kits or packages do not come with wire.The installer is responsible for the wires and cables needed for their installation.They do this because every installation is unique, and the preference is to keep the package price low.The enormous challenge of wire choice depends on the budget and project.An understanding of wiring materials and diagram is needed to make the correct purchase decision for a PV solar system [19].

•
There are many types of wire, which can get confusing.Wires differ in terms of the conductor material's insulation and flexibility.The most popular and widely used conductor for solar applications is pure copper.Aluminum is another option.It is relatively cheaper than copper.Wires can come with various insulation types that vary in terms of their protective properties.Some work better in high temperatures, high moisture conditions, under high UV exposure, or when exposed to fire than others for indoor solar wiring, such as in sheds or garages.The wire can have a solid core construction or standard, so it is flexible.Standard wire offers a greater surface area for flow and thus delivers better conductivity than solid cores.In most cases, it is best to use standard wire for PV solar systems.

•
The wire's thickness and length determine how much current can be safely carried.
A PV designer or electrical engineer can find the economically optimal wire size.
There is massive investment in solar panels, inverters, charge controllers, mounting equipment, and batteries in PV solar systems.The plant is at risk if one chooses the wrong excess carrying capacity for wires.One of these risks is the friction effect.Overloading occurs when the current increases and more thermal energy dissipates.Thus, the operational temperature of the insulation and the wire rise beyond a specific limit.In some cases, voltage loss causes equipment failure or malfunction [78].More panels can be added to the system and rewired at some points.The cables should meet weather and UV resistance requirements, withstand an operating temperature range of −40 • C to +125 • C, and withstand the voltage, depending on the application.Flame-retardant, halogen-free insulation, and sheath properties are considered self-extinguishing as well as acid-and alkaline-resistant characteristics.Cables should maintain short circuit resistance at high temperatures of 250 • C. It is preferable to have a small diameter to save space and allow the wire to be abrasion-resistant and have a high mechanical strength.PV cable installation should take as little time as possible to minimize the DC voltage drop and reduce the magnetic field's susceptibility [79].
Most of these losses are design issues, while none are stable-they vary according to the load conditions.Correct design and sizing of the cables, as well as regular electrical maintenance, are the main ways to combat DC and AC cable losses.They are impacted by choosing the right components and installing cable runs with suitable cross-section areas.

Inverter Losses
Inverters in PV solar systems mainly determine the functionality, for example, the static and transient characteristics, performance, and reliability.These inverters' essential functions are DC-AC conversion, MPPT, current grid control, active anti-islanding, and various monitoring and protection requirements.The trend nowadays is to use smart inverters with grid support features.Inverters are classified as grid-connected and stand-alone, single-phase, or three-phase.Concerning transformer isolation, inverters can be classified based on their line frequency, for example, high-frequency transformer or transformerless intervers [80].
Inverters can be classified as central, string, micro, and multistring inverters.

•
Central inverters are used in large-scale applications, as shown in Figure 15.Their peak efficiency is around 98%.They have some problems due to a mismatch between modules and strings.A loss of single inverters leads to the entire or a large part of the power generation being lost.

•
String inverter systems are used in residential applications, ranging from 2 kW to 6 kW, as shown in Figure 16.In this inverter type, there are multiple strings with individual inverters as possible configurations.String-level MPPTs are better than nonoptimal central inverters.

•
Microinverters are used in applications requiring less than than 500 W.They are mounted at the back of the panel with one per panel.There is a direct connection to the single-phase grid through AC wiring, as shown in Figure 17.Concerning MPPT, there is a higher energy yield than string converters, especially when significant shading is expected.This type requires the elimination of high-voltage and high-current DC switches and wiring.• Multi-string inverters combine the higher energy yield of a string inverter with the central inverter's.Each string has its MPPT implemented alongside the DC-DC converter.
Choosing a suitable inverter depends on the overall power system's size.These converters are connected via a DC bus to the inverter and, ultimately, to the grid.A new string with a dedicated DC-DC converter must be included within a specific power range to expand the system's size.Central and string inverters require less labor hours and are more affordable than microinverters.Additionally, they need fewer connections through cables than microinverters.However, microinverters can undergo rapid shutdown.There is no doubt that inverters are the most sophisticated devices in the PV solar system, despite their high failure rate compared to other system devices.Table 6 shows the pros and cons of the topologies of inverters used in PV solar systems.

The case study analysis
recorded in th for this study both facilities tem 2 has be recorded in ea To compar since peak po divided by it and 56 kW fo appearing in kW p for the are observed for System 2, result, as the o closer to the M greater ease inverter to M distributed la production th mated life of 1500 € up for are higher in t to be inspecte ure in the dis plete stopped A detailed pleted, in ord seasonal patt The proposed analyze the in mance, distri intervals.It [12,15].Detai PV arrays, len ifications of necessary.
Total daily inverter syste P I:S: ¼ P PVpanels where P PVpanel DC wiring los system.Wirin and the dista and the distan ing losses), for

The good things about AC solar panels and micro inverters
There are a few problems with solar panels string arrays which micro inverters can help to solve:

High DC voltage
Sending a high DC current through a cable can create a lot of heat, the nature of DC electricity can cause electrical cables to loose their conductivity creating resistance and even more heat increasing the risk of re and arcing.Because each micro inverter converts the DC to AC at the panel before it travels through a cable this risk is reduced.

Switching hardware
The fuses and protective systems for high voltage DC power are more expensive than those used in AC systems.

The effect of shade on solar panel output
Below is a good video by SolarQuotes.com.au about how the shade can effect the output of solar panels.Stand-alone PV solar systems are mainly used for DC loads, such as mobile applications, street lamps, signs, telephones, and water pumps connected to DC motors.On the other hand, stand-alone AC loads are used in remote or off-grid applications because it is not economical to extend the power grid.These systems are used in complete solar homes with conventional AC loads, such as water pumping applications.Grid-connected solar PV systems mostly uses central inverters and they have applications in systems ranging from 250 kW up to 1 MW.Typically, large PV solar plants have several MW scale inverters.The topology choice for implementation depends entirely on the system's needs, size, and budget.The inverter choice for a PV system depends on the inverter's characteristics, and the inverter should be as efficient as possible.Thus, it must deliver maximum amount of PV-generated power to the grid or load.
Under rated conditions, the typical efficiency is more than 95%.An active islanding detection capability is essential for grid-tied inverters.Islanding means that the inverters in a grid-tied setup continue to power the system even though the grid operator's power is limited.Islanding needs to be prohibited due to safety issues.Therefore, inverters are expected to respond and detect by immediately introducing power to the grid.This is referred to as anti-islanding.In many situations, solar inverters are exposed to ambient conditions.They must comply with the location's temperature and humidity conditions, since grid-tied inverters pump power into the grid.A high quality must be maintained to prevent the disruption of the grid's power flow.Thus, inverters are expected to have a low harmonic content on the line currents.This increases the lifespan of the inverter, the crucial power electronic device in modern PV systems.A suitable inverter is probably attained under favorable conditions with a lifetime of around 10-12 years.The modules in a PV system can last for over 25 years [82].
There is no benefit in harvesting energy from solar arrays during low insulation and low-light periods (early day, late day, cloudy day).Inverters convert a fraction of the virtually offered energy.The use of high-performance power electronics (HPPE) double conversion was recently attempted [83] to maximize the system's efficiency and therefore its profitability.Many factors should be considered when estimating inverters, such as the electrical yield (kWh/kW), inverter's lifespan and warranty, modularity, indoor vs. outdoor installation, considerations inside the cabinet, high and low ambient temperatures, and transformer isolation [84].
The decent cooling of PV solar system inverters is an essential criterion to guarantee the reliability of their operation.If the junction temperature of switching devices exceeds the limits, the devices fail.Heat sinks are used to remove the dissipated power in switching devices.Thus, an adequate heat sink needs to be chosen for a particular application.It is necessary to estimate the power dissipation in the switching device.The ideal switches have zero ON-state drops and, hence, no conduction losses, zero leakage current, and no OFF-state loss.Additionally, turn-ON and turn-OFF transitions are instantaneous, and there is no energy loss during switching transitions [85].In comparison, practical losses are finite forward drops and conduction losses as well as finite turn-ON and turn-OFF transition times.The transition between switch states is instantaneous, and the voltage drop across the conducting throws is zero.
Power losses in an inverter can be expressed as shown in Equation ( 17).
P AC = P DC − P conduction − P switching − P stray (17) The switching energy loss is calculated based on the IGBT turn-ON energy loss (E ON ) as a function of the DC voltage, current, and junction temperature and the IGBT turn-OFF energy loss (E OFF ) as a function of the DC voltage, current, and junction temperature.They are available in the IGBT datasheets for various operating and environmental conditions.The calculation of inverter switching is based on having a constant DC bus voltage, E ON , and E OFF that vary with the load current.Additionally, the ripple in currents is neglected.The variation in the switching energy loss with current can be approximated by a simple function (linear, piecewise linear, or parabolic).Thus, the switching loss is the product of the average switching energy loss and the switching frequency.Losses are calculated based on how much current passes through the switch.Each switch has a DC input and an AC output voltage to characterize inverter losses and correlate them to obtain precise efficiency measurements.The resistance of each switch is estimated with a time-aligned temperature.The average conduction loss in a power semiconductor device depends on the switch and connection resistances [83].It can be calculated using the following Equation ( 18) where I on (avg) and I on (rms) are the average and rms conduction state currents, respectively.They can be determined from the converter's operating conditions.V ON and R ON are the ON-state forward voltage drop of the device and the ON-state resistance of the switching device.It should be noted that MOSFET does not have V ON , and other devices have negligible R ON [82].The turn-OFF loss can be expressed by Equation ( 19) where V OFF and I ON are the voltage at the OFF-state and the current at the ON-state, t f i is the current fall time for the device, and F s is the switching frequency of the converter [84].
The turn-ON losses can be expressed by Equation ( 20): where t ri is the current rise time of the transistor, I rrm is the reverse recovery current, and t rr is the reverse; these expressions are somewhat simplified approximations.For accurate estimations, the effects of the operating temperature, drive circuit design, and parasitic elements of the layout should be considered.The total power dissipation may be determined by summing all loss components.The losses may be observed depending on the converter's switching frequency.The total switching power is given by Equation ( 21) Thus, ON/OFF energy losses depend on the frequency; losses increase with the turn ON/OFF time [82].E ON and E OFF are energy the ON/OFF states available on the datasheet.
V ds and I ds are the voltage and current drain sources, respectively.Good differential measurements are needed to measure precise voltage and speed values to catch the rise and fall times.
In contrast, stray losses are a kind of catch-all for other losses.They include the OFF-state, support circuit, and gate losses and all other losses that are difficult to characterize.

Transformer Losses
Losses in a transformer can be classified into two main categories: iron losses and copper losses [86].Iron losses are defined as core losses (constant losses).These losses are mainly classified as hysteresis losses and eddy current losses.The hysteresis losses are the iron core's repeated magnetization and demagnetization cycles caused by energy losses produced by the alternating input current.These losses can be minimized by using a core material with minor hysteresis loss alloys, such as Mumetal silicon steel, or nanohysteresis loops.When the magnetic field's direction changes, some energy is lost due to heating.Thus, the core's magnitude and the direction of the core's magnetic field should be changed.This energy loss is reduced by using a core made of soft iron.The field lines produced by the primary coil may not entirely cut the secondary coil, especially if the core has an air gap or is poorly designed, contributing to the transformer's flux leakage loss.This can be improved by winding the secondary coil on top of the primary coil to ensure that all field lines from the primary coils pass through the secondary coils.Eddy currents are circulating currents in nature, and the eddy current losses are caused by the induced currents flowing in conductors due to the magnetic field formed by the alternating current, leading to energy wasted as heat.The eddy currents depend on the material's conductivity (σ).They can be reduced by adding silicon to the material.However, silicon decreases the strength of the material.Thus, around 3-5% can be added.In a practical transformer, these losses are minimized by using a laminated core made of thin sheets of soft iron insulated from each other to provide higher resistance.The high resistance reduces the eddy currents' flow and energy loss due to eddy currents in the core.Copper losses are caused when the currents flow into the primary and secondary windings' resistances, resulting in heat generated by the I 2 R losses.Thick copper wires with considerably lower resistance minimize these losses [87].

Transmission Line Losses
In modern society, electricity has become a necessity.However, transmitting this power across continents is not as simple as running a cable due to the relatively large power line resistance over long distances.Power plants have to be built every few blocks to minimize power loss [88].Alternative currents (AC) improve this problem by using a transformer to set up voltages for long-distance transmission and back down.However, this presents an entirely new set of problems.While every conductive line has intrinsic resistive properties, AC causes another type of impedance known as reactance, which causes further losses due to the line's inductive and capacitive properties [89].Inductors resist changes in current, temporarily storing energy in the magnetic field.Capacitors resist changes in voltage, temporarily storing energy in the electric field [87].These can cause phase shifts between the voltage and the currents in the line and cause an increase in resistive losses.This is minimized by adding capacitor banks at power stations to adjust the power factor.High-voltage power lines often emit a superior sound due to the air's ionization around the power lines.This is known as corona discharge.While the air is relatively insulative, having too large of an electric field can pull the atoms' electrons, making the air conductive due to potentially substantial power losses.Corona discharge is minimized by increasing the cables' diameters and bundling multiple wires to increase the surface area.The voltage of the power lines is generally kept well below 2 MV.When voltage levels are above this limit, the electric field is so large that the corona discharge loss surpasses the resistive loss of the lines themselves.Even with these precautions, power loss is unavoidable.In transmission lines, 2-4% of the power is often lost [90].

Optimizing the Design of the PV Solar Power Plant
The PV solar power system design is optimized to increase performance and reduce operating costs.The MacLeamy curve shown in Figure 18 shows that the sooner changes are made, the better and the cheaper the whole process is.The developer can optimize their PV solar power system at the very early stage of the project by adjusting the pitch distance and AC/DC ratio and accelerating PV by speeding up the time to layout and reducing the levelized cost of energy (LCOE).Thus, the efficiency is improved and more generation is obtained from the PV solar system.There are immediate improvements and some of the following solutions are implemented: • Site evaluation factors, such as solar resources, the geometry of the site, the interconnection strategy, grid requirements, local restrictions, market situations, row orientation, and the shade stripe [92,93].

•
The optimization of cleaning solutions, which is paramount to lowering the cost and increasing the performance and profitability of the plants [55].The cleaning solutions can be classified as manual, semiautomated, and automated.Manual cleaning is typically done in regions in which labor is cheap.Tractors and brushes in areas with low soiling rates require low cleaning frequencies.Semiautonomous robots are cheap and typically used for smaller projects with high amounts of soiling and labor.Fully autonomous robots are typically used for remote projects in regions with extreme weather and soiling conditions that require a high cleaning frequency [52].Each solution has different concerns, needs, and water availabilities.Soiling management solutions have lower costs per MW, increasing the site's profitability [53].

•
Configuration parameters, such as [94] -The preliminary design and equipment selection.-A PV solar system's bill of materials (BoM) includes the PV modules' encapsulates, front surface, back sheet, and interconnections, as well as inverters (central/ string) and module mounting systems, such as horizontal single-axis trackers, and a fixed tilt.

-
The optimal ground coverage ratio (GCR) is around 3-3.5.A higher GCR reduces shading losses (by measuring a structure's length and the PV's pitch.The pitch is related to shade control.If more land is used, more land is leased, and there are longer cables, roads, or trenches and more giant perimeter fences or greater vegetation management).

-
The DC/AC ratio (the ratio between the DC capacity of the array compared to the AC capacity of the inverters).The optimal value is around 1.17.

-
The clipping loss (this phenomenon happens when the array's maximum power point tracking (MPPT) is greater than the maximal power available from the inverter).A high ratio can provoke a clipping loss.The inverter cannot work under these conditions.-Economic aspects of the inverter, including the cost, electrical balance of the system's costs (BoS) (the BoS encompasses all components of a PV solar system, other than the PV system's panels.It includes the wiring, switches, amounting systems, solar inverters, battery banks, and chargers).

-
The aging of the equipment.

•
The final equipment selection.

-
The final optimization of the selected component and the final layout drawings.

-
The layout research algorithm presents the preliminary equipment and helps to explore possible configurations to minimize the LOCE.

-
A suitable components rating should be installed based on how much PV solar power plant is generated.

-
The PV solar system structure's (bifacial/monofacial) arrays, the (string/central) inverters, and the (tracker/ fixed) arrays depend on the topography analogies of the site and the amount of power [95].

-
Weather station selection such as dust detection sensor should meet the PV solar power plant location.

• Operation and maintenance [97]:
-The owner employs the entire in-house maintenance staff and provides all operations and maintenance tasks.-Full-turn key operational and maintenance contracts that give ability and performance guarantees to the power plant owners.-Capex investment and secure life value of up to 20-30 years of maintenance.
Capex is calculated based on the infrastructure equipment and installation [98].
• Performance enhancement using intelligent solutions: -The power purchase agreement (PPA) is a contractual agreement between energy sellers and buyers..A PPA is usually signed for a long-term period of 10-20 years.

-
The industry always strives for innovations, long-term views, the implementation of new technologies, and the ability to monitor performance.

-
The LCOE is beneficial as it compares systems built with different technologies by giving the currency value per unit of energy.There is a simple balance between an efficient project in terms of energy production and an economically viable one that reduces capital investment and operational costs.

-
There should be no escalation of operating expenses (OpEx) (the day-to-day expenses that a company has to keep its business running.).Thus, a flat OpEx means that whatever is paid on day one is the same as that paid in year 20.

System Under Study
Recently, PV systems have increasingly been integrated with the electrical grid in Jordan, facilitating procedures.One of the most important grid-connected PV systems is Quweira solar power plant, a 103 MW photovoltaic power station owned by the Quweira/Aqaba government, as shown in Figure 19  Typically, fixed solar panel arrays are mounted on a sloping roof with a carefully selected orientation, e.g., facing straight south in the northern hemisphere.The two ways that the sun traverses the sky are horizontally, as it moves from east to west, and vertically, as it rises and falls.The angle of incidence at which the sun's rays strike the panel's surface changes and becomes more oblique as it passes across its face.As a result, the ability of the solar cell crystals to convert energy is diminished.Trackers that only follow one axis-horizontal movement-are known as single-axis trackers, and dual-axis trackers follow both axes.Single-axis trackers can recover up to 45% more of the sun's energy, while dual-axis models can save a massive 65%, so they work well.Unfortunately, they are costly and inappropriate for all circumstances, but they are still worth considering.
A central converter outfitted with three or four blocks connected to the same PV and a medium voltage transformer in parallel.Table 7 shows the Quweira PV power plant's rating capacity.Table 8 shows the plant's main components.Table 9 shows the mechanical characteristics of the Quweira PV power plant module.Table 10 shows the Quweira PV power plant's array specifications.Table 11 shows the Quweira PV power plant's central inverter specifications.Table 12 shopws the Quweira PV power plant's cable and transformer specifications.

Results and Discussion
Figure 20 shows the wind speed as a function of the ambient temperature and pressure at the Quweria PV power plant.Figure 21 shows the typical vs. the measured values of POA Irradiance for the fixed plant.Figure 22 shows the typical vs. the measured values of POA irradiance for the tracked part plant.Figure 23 shows a sample of ambient temperatures ( • C) at the location of the system under study.Figure 24 shows a sample of wind speeds.Figure 25 shows sun paths (height/Azimuth diagram).The total PV arrays are represented by 20 modules connected in series and 8640 strings connected in parallel.Figure 26 demonstrates the characteristics of the PV array at different irradiation levels for the combined arrays used.Figure 27 demonstrates the characteristics of the combined PV array at different temperatures.Figure 28 shows the array temperature vs. the effective irradiance.
As mentioned in this work, PV power plant losses include thermal losses.The thermal balance in the PVsyst software involves the heat loss factor, known as U.It is calculated as shown in Equation ( 22) where U c is the constant loss factor, W/m 2 K, U v is the wind loss factor (W/m 2 K m/s), and wind vel is the wind velocity (m/s).Table 13 shows the balances and main results, where GlobHor is the global horizon irradiation, DiffHor is the horizontal diffuse irradiation, T Amb is the ambient temperature, GlobInc is the global incident in the collector plane, GlobEff is the effective global correlation for the IAM and shading, EArray is the effective energy at the output of the array, E Grid is the energy injected into the grid, PR is the performance ratio, EArrMPP is the array's virtual energy at the MPP, and EArray is the effective energy at the output of the array.The main parameter needed for the wiring losses of the PV array is the resistance of the circuit according to the wire lengths and sections.Wiring loss may be evaluated as a percentage of the system's power under STC.Losses of cables between the output of the inverter and the injection point of the energy meter should be considered.The distance and wire section should be defined earlier.The external transformer loss should be considered in a high rating system (MW).The LID mismatch parameter reflects the confidence of matching the actual module set's performance concerning the manufacturer's specifications.The default PVsyst value is half of the lower tolerance level for the module's exposure to the sun.A typical value for the LID loss factor for P-type wafers is 2%.The current mismatch within a string is essential, because the current in the weakest module dominates the current in the whole string.Voltage mismatch between strings has a lower impact on the system's performance.The soiling loss is almost negligible in temperate climates and residential situations.It may become very significant in some industrial environments, such as systems near railway lines or in a desert climate.Each month, the soiling loss can be defined individually to account for periodic cleaning, rainy periods, or eventual snow covering.The soiling loss factor is 3%.IAM is defined in the PV module within the component database.Specific studies can be conducted using a standard profile based on Fresnel's laws.The auxiliaries include fans, air conditioners, and electronic devices.Thus, Figure 29 shows the loss flow diagram for the plant under study.Figure 30 shows the plant's power output distribution.Figure 31 shows the normalized production per installed kWp.  Figure 32 shows the nominal power at the input of the inverter.The operating conditions above these values are limited.The violet curve shows the power, and the green curve shows the power available from the array.In case the array is working at its MPP.The difference between these two curves represents the overload power loss.The overload power loss percentage is the area between these curves concerning the entire histogram area.PVsyst software considers the sizing to be acceptable when the overload loss does not exceed 3%.When the overload loss is 1-3%, PVsyst software shows a slightly undersized inverter and has an orange warning.However, if the overload exceeds 3%, PVsyst software gives an error message in red, and the simulation is impossible.If the designer wants to create a system with a highly oversized PV array, they need to increase the potential limit of 3% in the project's settings.The nominal power P nom−ratio is known as the DC/AC ratio.A good sizing usually corresponds to a P nom−ratio of 1.25-1.3.Note that the simulation's overload loss may significantly differ from the sizing value.The histogram calculation for this rough sizing tool cannot consider all system losses.Thus, the ratio of the inverter loss to the nominal inverter power is −1.89%.

Array power (kW)
Energy (kWh) One of the most critical electrical specifications in the PV solar system is the panel efficiency [100,101]: the higher the efficiency, the smaller the surface area needed to generate a specific output power.The size of the PV array is based on the energy production in the darkest time of the year.Additionally, the panel output depends on the insulation, temperature, and R L .The inverter size should match the array size.Additionally, the inverter size is based on the R L peak.The PV's output voltage must be within the appropriate range in all weather conditions throughout the year.The inverter's efficiency varies depending on the R L .Simultaneously, extra cooling might be needed when the temperature is over 40 • .Thus, system design begins by analyzing the loads that need to be powered.PR (performance ratio) is an essential tool or factor that is used globally by companies and professionals to assess the healthiness of solar PV plants [102,103].It is considered an important metric in the PV industry.When commissioning a PV system, it is often used as a contractual condition and part of the warranty.It is not altered by the system's size or type.It is the ratio of the effective produced energy to the ideal energy yield under STC.Usually, the energy produced is the available usable energy delivered to the end-user or the grid.The PR ratio includes the optical, PV array, DC to AC conversion, and other plant losses.A simple annual PR is measured based on actual the usable energy and the annual solar irradiance [104].It is considered an indication of the peak capacity of the PV power plant and is independent of the location-specific irradiance [105].It is given by Equation ( 23) where E is the electricity generation (kWh/year), P p is the PV module's installed capacity (kWp), G POA is the total global solar irradiation sum on the plane of the array (kWh/m 2 /year), and G STC is the global solar irradiance under STC = 1 kW/m 2 .PR can be classified into two types based on its significance and applicability.First, there is the STC equivalent PR.This is calculated by adjusting the power at each recording interval to compensate for the difference between the actual PV module temperature T ambient and the STC reference temperature at 25 • C.This method is normally used when the plant's PR is to be measured for a short duration in the day.Second, there is the annual temperature corrected PR.This calculates the PR during the reporting period using the power at each recording interval to compensate for the difference between the actual PV module's temperature T ambient and the expected annual average module's temperature.The annual temperature correction is significant when the annual PR must be validated within the first 15-20 days of operation.Table 14 shows the monthly PR [99].It shows that the plant is healthy and verifies the annual energy yield [106,107].Table 15 shows the main output for the plant under study [108].Optimizing a PV plant's design increases its performance and reduces the operating costs.The PV solar system development process can be classified into fixed design development processes, including a regulatory framework, project site specifications, solar resources, and client requirements.The configuration analysis includes equipment selection, the design of the plant's layout, contracting, and operational strategies-the iterative processes concerns energy efficiency and yield calculations.Usually, grid outages and equipment shutdowns are not considered as part of the PV solar system's efficiency, despite representing 2-3% of the total energy loss.Most losses are associated with the components' characteristics and design issues.Some approaches can help to reduce these losses, such as regular maintenance, shading prevention, and regular cleaning to guarantee that the maximal amount of sun energy reaches the panel's surfaces.The equipment for the system under study, such as the panels, mounting structures, combiner boxes, warehouses, sensors, and especially, the pyranometers, appeared to be clean and in good operating condition; even the internal roads were clean.The site security is controlled and monitored by gates and fences and was found to be in acceptable shape.The scheduled preventive and corrective maintenance activities are performed regularly.A random spot check of the PV module was executed.It is worth mentioning that the Quwiera PV power plant is an optimal case, corresponding to a DC/AC ratio of 1.17, a GCR of 3.1, and a PR of 80.9%.

Conclusions
An adequate PV solar system has a high level of performance, long-term efficiency, and durability.Thus, putting effort into PV solar system losses can potentially exceed financial savings.The next step is to match the power use by shifting the load to the free electricity generation period.Understanding the PV solar loss asset management strategies can boost solar performance.Hence, the industry should develop technologies in succession and plan to prevent and reduce these losses.This review discussed the various causes of PV system losses.There have been many developments to minimize these losses in PV, such as improving the quality of materials using bifacial solar panels that use front and rear irradiation.System components have losses in energy between states, a decreased range, an increased weight/volume, and the creation of heat.Characterizing losses can help us to understand, mitigate, and manage them using the most accurate measurements to achieve reasonable measures for the derived values.Reducing a PV solar system's losses maximizes its power output and return.This work presented a study of grid-tied PV solar systems using PVsyst software.The analysis showed that the PR of the system under study is 80.9%.The measured yields for the fixed and tracked systems were 98,800 MWh and
Figure content uploaded by Ned Djilali Author contentContent may be subject to copyright.

Figure 8 .
Figure 8. Components in which a fire started in 180 PV power plant locations in Germany between 1995 and 2021 [39].

Figure 10 .
Figure 10.IAM-PV power plant losses-a comparison of surface reflection from a silicon solar cell with and without a typical antireflection coating [44].

Figure 11 .
Figure 11.PID effect in string PV modules.

Figure 12
Figure12shows three levels of strategy under control (plant, panel, cell) and the environmental factors that can not be controlled.The PV module's PID process may overgrow and affect the entire PV plant's performance in the shortest period.Consequently, this results in damage to the PV's plant financing and operation.PID can be prevented and reduced at the plant level.Humidity and temperature influence the leakage current in conjugation with the voltage level in the installation determined by the module connection scheme and solar irradiation.The leakage current peaks during morning hours when the modules' faces are covered with morning dew [59].

Figure 1 .Figure 13 .
Figure 1.Plant capacity in the cases with 0%, 1% and 2% annual degradation respectively.The gray shaded areas illustrate the difference in produced electric energy between the three cases.

Figure 20 .
Figure 20.Wind Speed as a function of the ambient temperature and pressure in the Quweria PV power plant.

Figure 23 .
Figure 23.A profile of the ambient temperature ( • C) measured in June.

Figure 24 .Figure 25 .
Figure 24.A profile of the wind speed (m/s) measured in January.

Figure 26 .Figure 27 .Figure 28 .
Figure 26.The characteristics of the PV array at different irradiation levels.

Figure 29 .Figure 30 .
Figure 29.Loss flow diagram for the plant under study.

Table 1 .
[29]r generation stations are connected on transmission lines (MW) based on fuel use in Jordan[29].

Table 2
Case study of the technical specifications of both systems.

Table 2
Case study of the technical specifications of both systems.

Table 6 .
The main pros and cons of the topologies of inverters used in PV solar systems.

Table 12 .
Quweira PV power plant's cable and transformer specifications.

Table 13 .
Balances and main results.

Table 15 .
Main outputs for the plant under study.