Search Results (185)

High-power thulium-doped fiber lasers (TDFLs) operating near 2050 nm are of great interest for applications including atmospheric gas sensing and free-space optical communication owing to the favorable atmospheric transmission and the strong absorption bands of carbon dioxide (CO₂). Here, we report an all-fiber high-power TDFL based on a 793 nm-pumped master oscillator power amplifier (MOPA) architecture. The system comprises a custom-built linear-cavity seed laser and two amplification stages. With a maximum pump power of 818 W, the final amplifier delivers 501 W at 2050 nm with a slope efficiency of 51%. Stable operation is confirmed over two hours at full power, with an RMS power fluctuation of only 0.47%. The measured beam quality factors $M^2$ are 1.31 and 1.27 in the horizontal and vertical directions, respectively, indicating near-diffraction-limited performance. The demonstrated system combines high output power, excellent stability, and good beam quality, and thus provides a promising laser source for 2 μm high-performance applications. Full article

We extended self-similar amplification to a large-mode-area tapered Yb-doped fiber (LMA T-YDF) with longitudinally decreasing nonlinearity. The theoretical analysis and numerical simulation demonstrate that T-YDFs with different nonlinearity profiles can achieve self-similar evolution, which is confirmed by a self-similar amplifier that employs two kinds of T-YDFs. Further experimental study indicates that the T-YDF with a large core diameter at the thin end can achieve self-similar evolution across a wide range of pump powers and generate 51 W average power, 34 fs nearly transform-limited (TL) pulses with 32 dB gain. To the best of our knowledge, this is the first theoretical and experimental demonstration of self-similar amplification in T-YDFs. The high-gain feature of the T-YDF simplifies the laser system and can be used to build a compact all-fiber high-power femtosecond laser source. Full article

A 1319 nm, single-frequency, two-stage partially end-pumped slab (Innoslab) amplifier with high output power and excellent beam quality was reported. A 3 W, quasi-continuous wave pulsed, single-frequency all-fiber seed laser was amplified to a maximum average power of 154.0 W with a magnification of ~51.3 and overall optical-to-optical efficiency up to 12.0%. The output pulse width was 132.6 μs at a repetition rate of 500 Hz. The beam quality factors of M² were 1.4 and 1.3 in the horizontal and vertical directions, respectively. The power stability at the maximum output power was 0.43% (RMS) in 10 min. Higher output power and optical-to-optical efficiency could be achieved through optimizing mode matching between the pump beam and the seed laser beam. Full article

This paper presents an absolute distance measurement system based on three-wavelength synchronous phase-shifting interferometry. A synthetic wavelength chain is established using three semiconductor lasers in an all-fiber Fizeau interferometer. By integrating a piezoelectric transducer (PZT)-driven sinusoidal phase modulation with multi-channel synchronous sampling for phase demodulation, and further combining it with a fractional multiplication method, the proposed system achieves high-precision absolute distance measurement over an extended range. Experimental results demonstrate an unambiguous measurement range of 240 μm, a static measurement precision better than 0.6 nm, and a dynamic displacement measurement accuracy superior to 2 nm in comparison with the reference device. The main error sources of the system, including synthetic wavelength uncertainty, phase measurement uncertainty, and air refractive index uncertainty, are systematically modeled and analyzed. In addition, the influence of dynamic factors, such as PZT nonlinearity, is discussed and compensated. The proposed method provides a robust and high-precision solution for absolute ranging and shows strong potential for applications in industrial precision inspection and optical sensing. Full article

Hail is one of the typical manifestations of severe convective weather, characterized by its sudden onset and strong localization. In this study, a compact all-fiber coherent Doppler lidar (CDL) working at the 1.5 μm wavelength is employed to detect a hail event. Combined with ERA5 reanalysis data, Parsivel², and cloud-type products from the Fengyun satellite, the synoptic background of the hail event was analyzed. Owing to its high-precision spectrum measurement capability, the CDL can effectively separate the multi-component power spectra of precipitation particles. By comparing particle velocity, spectrum width and skewness as characteristic parameters from signal separation across light rain, hail and heavy rain, the distinctive power spectrum characteristics of hail were identified. This study verifies that CDL can provide high-spatiotemporal-resolution data support for the short-term forecasting of hail events. Full article

Singlet oxygen (¹O₂) is a key mediator in photodynamic therapy (PDT), and its generation and reactivity in biological systems have been extensively studied. It has been shown that laser radiation at near-infrared (NIR) regions can be used to directly generate ¹O₂. In this work, we investigated photosensitizer-free ¹O₂ generation using an original all-fiber pulsed laser operating at 1066 nm and 1241 nm and evaluated its impact on mitochondrial activity in U-87 MG glioblastoma cells. Singlet oxygen was evaluated using the 1,3-diphenylisobenzofuran (DPBF) chemical probe and confirmed with argon-purging controls, demonstrating clear oxygen- and wavelength-dependent effects. Laser irradiation of glioblastoma cells demonstrated distinct effects depending on the wavelength, although decrease in cellular metabolic activity was observed in both cases. Interestingly, some inhibitory effect was also observed when the culture medium was pre-irradiated at 1241 nm and subsequently added to intact cells. These results demonstrate that laser radiation at both studied wavelengths can elicit measurable biological effects, although the relative efficiency in chemical versus cellular systems varies. Collectively, these findings provide a foundation for further systematic studies of wavelength-specific NIR interactions with cellular and molecular components in biological environments. Full article

We report the generation of sub-50 fs mid-infrared (MIR) pulses using a fiber-integrated system comprising a several-centimeters-long chalcogenide (As₂S₃) fiber and a fluoride (ZBLAN) fiber. Initially, 127 fs pulses at 2.8 µm are generated via the soliton self-frequency shift in the fluoride fiber. These pulses are then coupled into the As₂S₃ fiber, which provides substantial normal dispersion at this wavelength, enabling temporal stretching to achieve pulse durations of 1.02 ps (8 cm), 2.06 ps (15 cm), and 4.45 ps (24 cm), corresponding to a maximum stretch factor of approximately 35. Simultaneously, the pulses undergo significant spectral broadening via self-phase modulation during this process. Subsequent nonlinear compression within an optimized ZBLAN fiber yields compressed pulses as short as 46 fs, representing a compression ratio of approximately 63%. This work represents, for the first time, picosecond stretching and sub-50 fs nonlinear compression in a fiber-integrated architecture at 2.8 μm, establishing a critical component for future all-fiber MIR-chirped pulse amplification systems. Full article

Line-field spectral-domain optical coherence tomography (LF-SD-OCT) offers high-speed parallel imaging, but lateral beam expansion limits the photon budget per spatial channel, compromising sensitivity. Here, we demonstrate a high-speed LF-SD-OCT system driven by a gain-managed nonlinear (GMN) all-fiber source operating at a central wavelength of 1063.2 nm. Delivering 269 mW of average power with a smooth 98 nm (3 dB) bandwidth, the GMN source effectively fulfills the stringent photon budget and stability requirements of parallel detection. The system achieves a 5.68 μm axial resolution and a ~1.2 mm effective imaging range. Ex vivo porcine myocardial tissue ablation experiments validate its capability for high-contrast cross-sectional visualization of ablation crater morphology, showing excellent agreement with optical microscopy. These results establish GMN-enabled LF-SD-OCT as a robust solution for the precise intraoperative monitoring of laser-induced tissue damage. Full article

We have demonstrated a high-power, polarization-maintaining all-fiber amplifier operating at a repetition rate of 1 MHz. The seed laser is a Semiconductor Saturable Absorber Mirror (SESAM) mode-locked oscillator with an 18.1 nm full width in half-maximum (FWHM) spectrum. The pulse duration is stretched to 1.1 ns using temperature-controlled chirped fiber Bragg gratings (TCFBGs) and subsequently amplified in a 40 µm core Yb-doped fiber, achieving a maximum output power of 37 W. The amplified laser exhibits excellent beam quality with an M² factor of 1.04. The pulse duration is compressed to 207 fs in a single-grating compressor with 86% efficiency, yielding an average power of 32 W, a pulse energy of 32 µJ, and a peak power of 154.6 MW. This high-power all-fiber femtosecond laser is a promising source for scientific and industrial applications. Full article

This study introduces an all-fiber optic sensing network based on fiber Bragg grating (FBG) technology for structural health monitoring (SHM) of launch vehicle payload fairings under extreme thermo-mechanical conditions. A wavelength–space dual-multiplexing architecture enables full-field strain and temperature monitoring with minimal sensor deployment. Structural deformations are reconstructed from local measurements using the inverse finite element method (iFEM), achieving sub-millimeter accuracy. High-temperature experiments verified that FBG sensors maintain a strain accuracy of 0.8 με at 500 °C, significantly outperforming conventional sensors. Under 15 MPa mechanical loading and 420 °C thermal shock, the fairing structure exhibited no damage propagation. The sensing system captured real-time strain distributions and deformation profiles, confirming its suitability for aerospace SHM. The combined use of iFEM and FBG enables high-fidelity large-scale deformation reconstruction, offering a reliable solution for reusable aerospace structures operating in harsh environments. Full article

Two-dimensional transition metal dichalcogenides (TMDs) are key materials in ultrafast photonics. However, the performance of conventional TMDs is limited by their bandwidth and carrier recovery time. The novel Dirac semimetal nickel ditelluride (NiTe₂), with its broad-band response and excellent nonlinear properties, emerges as an ideal candidate for saturable absorber (SA) materials. In this work, we report, for the first time, the application of NiTe₂ in the ytterbium-doped fiber laser, demonstrating stable passive Q-switching operation. The nonlinear transmission curve reveals a modulation depth of 6.82% at 1 µm and a saturation intensity of 2.12 MW/cm². Using an all-fiber ring cavity structure, stable Q-switched pulses with a central wavelength of 1031 nm were achieved at a pump threshold of 94 mW, with a maximum pulse repetition frequency of 30.1 kHz. The minimum pulse width reached 2.3 μs, and the single-pulse energy increased to 3.05 nJ, with an impressive radio frequency (RF) spectral signal-to-noise ratio (SNR) of 58.9 dB. This study demonstrates the potential of NiTe₂ as a high-performance SA in the near-infrared region, providing a solid foundation for its future application in ultrafast laser technologies. Full article

We experimentally and theoretically demonstrate coexistence of three different wavelength-multiplexed bound dual-frequency pulses in an all-fiber mode-locked fiber laser, effectively achieved by exploiting polarization-dependent loss effects and two uneven gain peaks of Er-doped fiber. With the single wall carbon-nanotube-based intensity modulation, wavelength-multiplexed dual-frequency pulses located at 1531.1 nm and 1556.6 nm are obtained. Changing the polarization rotation angles in the fiber cavity, one of the two asynchronous pulses evolves into a bound state of a doublet, in which the center wavelength of the bound solitons is centered at ~1530 nm or ~1556 nm. The relative phase between the two bound solitons or modulation depth of bound solitons can be switched by a polarization controller. A simulation method based on coupled Ginzburg–Landau equations is provided to characterize the laser physics and understand the mechanism behind the dynamics of tuning between different bound dual-frequency pulses. The proposed fiber laser will provide a potential way to understand multiple soliton dynamics and implementation in optical frequency combs generation. Full article

A reflective all-fiber optical current transformer based on a spatial non-reciprocal phase modulation technique is investigated by theoretical analysis and experimental measurement. The modulation unit, composed of a phase delay wave plate (LiNbO₃) and two Faraday rotators, achieves flexible frequency adjustment by converting modulation from the time domain to the spatial domain. Therefore, the avoidance of the impact caused by delay coils is achieved in principle. The absence of intrinsic frequency limitations eliminates the demand for precise timing control in demodulation, thereby simplifying the demodulation circuit and reducing the cost and size of the transformer. In previous studies, redundancies were identified in the optical path coupling devices. The half-wave voltage of the modulator is excessively high, and its size is considerable due to constraints inherent in the manufacturing process. The measurement range is within 1800 A. The scheme simplifies some optical path components. By optimizing the phase delay wave plate, the half-wave voltage of the modulator is significantly reduced by a factor of 150. Experimental results demonstrate that the current transformer exhibits excellent detection consistency within the rated current range of 30–3600 A (1–120%), the response time is within 3 ms, and the measurement error and peak error reach 0.052% and 0.127%. This configuration provides a novel option for the design and practical application of all-fiber optical current transformers. Full article

A monolithic all-fiber high-energy chirped pulse amplification (CPA) system with a managed large dispersion is demonstrated. Considering the nonlinearity in the amplification system, two temperature-tuning cascaded chirped fiber Bragg gratings (CFBGs) with a large dispersion of 200 ps/nm are employed as stretchers to stretch the pulse duration to more than 2 ns in the time domain. The main amplifier, with centimeter-level length, a large mode area, and high-gain silicate glass fiber, increases the energy to 293 μJ at 100 kHz. A reflective grating pair with a high density of 1740 lines/mm is used to compress the large-dispersion chirped pulse into a compact structure. Owing to the high-order dispersion pre-compensation by the CFBGs and the large-sized grating with high diffraction efficiency, we achieved a compressed pulse duration of 466 fs with a maximum pulse energy of 250 μJ, corresponding to a compression efficiency of more than 85% and a well-preserved beam quality of M² < 1.3. To the best of our knowledge, this is the highest pulse energy ever reported in a monolithic fiber femtosecond amplifier. Full article

A 50.9-W all-fiber mid-infrared (MIR) supercontinuum (SC) laser with a conversion efficiency of over 76.7% is demonstrated in a ZBLAN (ZrF₄–BaF₂–LaF₃–AlF₃–NaF) fiber. The entire system consists of a broadband thulium-doped fiber amplifier (TDFA) operating at 1.9–2.6 μm and a piece of ZBLAN fiber. The system features an all-fiber architecture, which is achieved by directly splicing the pigtail fiber of the TDFA to the ZBLAN fiber. The system’s stability and reliability were ensured by the utilization of the water-cooled fusion splicing joint between the silica fiber and ZBLAN fiber, and an AlF₃ fiber endcap. When the seed pulse repetition rate (PRR) was 3 MHz and the pulse duration was 6 ns, a MIR SC laser with an average power of 50.9 W and a spectral range of 1.9–3.6 μm was obtained, with a corresponding power conversion efficiency (from the TDFA output to the SC laser output) of 76.7%. By adjusting the pulse duration to 4 ns, the generated SC laser exhibited a spectral range of 1.9–3.7 μm and an average power of 50.1 W, corresponding to a power conversion efficiency of 75.1%. Such a supercontinuum (SC) laser paves the way for the application of high-power SC lasers in a wide range of fields. Full article