Search Results (686)

In this study, edge-oxidized graphene oxide (EOGO) was used as an additive in fly ash (FA) geopolymer paste. The effect of EOGO on the properties of the fly ash geopolymer was investigated. EOGO was added to the FA geopolymer at four different percentages (0%, 0.1%, 0.5% and 1%), and the mixture was cured under two different conditions: room curing (~20 °C) and heat curing (~60 °C). To characterize the FA-EOGO geopolymer, multiple laboratory tests were employed, including compressive strength, Free-Free Resonance Column (FFRC), density, water absorption, and setting tests. The FFRC test was used to evaluate the stiffness at small strain (Young’s modulus) via the resonance of the specimen. The mechanical test results showed that the strength and elastic modulus were high during heat curing, and the highest compressive strength and elastic modulus were achieved at 0.1% EOGO. In the physical test, 0.1% EOGO had the highest density and the lowest porosity and water absorption. As a result of the setting time test, as the EOGO content increased, the setting time was shortened. It is concluded that the optimum proportion of EOGO is 0.1% in FA geopolymer paste. Full article

Metallic nanofoams with amorphous structures demonstrate exceptional properties and significant potential for diverse applications. However, their mechanical properties at different temperatures are still unclear. By using molecular dynamics simulation, this study investigates the mechanical responses of representative CuZr amorphous metallic nanofoam (AMNF) under uniaxial tension and compression at various temperatures. Our results reveal that the mechanical properties, such as Young’s modulus, yield stress, and maximum stress, exhibit notable temperature sensitivity and tension–compression asymmetry. Under tensile loading, the Young’s modulus, yield strength, and peak stress exhibit significant reductions of approximately 30.5%, 33.3%, and 32.9%, respectively, as the temperature increases from 100 K to 600 K. Similarly, under compressive loading, these mechanical properties experience even greater declines, with the Young’s modulus, yield strength, and peak stress decreasing by about 34.5%, 38.0%, and 41.7% over the same temperature range. The tension–compression asymmetry in yield strength is temperature independent. Interestingly, the tension–compression asymmetry in elastic modulus becomes more pronounced at elevated temperatures, which is attributed to the influence of surface energy effects. This phenomenon is further amplified by the increased disparity in surface-area-to-volume ratio variations between tensile and compressive loading at higher temperatures. Additionally, as the temperature rises, despite material softening, the structural resistance under large tensile strains improves due to delayed ligament degradation and more uniform deformation distribution, delaying global failure. Full article

(1) Background: Optimizing infill density in 3D-printed PLA parts reduces material usage, cost, and waste. This study examines mechanical behavior in the initial and hydration stages. The findings provide valuable data for numerical simulations and engineering applications in additive manufacturing. (2) Methods: PLA specimens were printed with infill densities of 100%, 75%, and 25%. Mechanical tests, including tensile and compression tests, and one-hour stress-relaxation at 2% strain were conducted. The digital image correlation method was used to obtain the strain fields on the samples’ surface under tensile loading. Mechanical properties, including the elastic modulus, strength values, and Poisson’s ratio, were assessed. Hydrolytic degradation effects over one month were also evaluated. (3) Results: Lowering the PLA infill density reduced the ultimate tensile strength (from 60.04 ± 2.24 MPa to 26.24 ± 0.77 MPa), Young’s modulus (from 2645.05 ± 204.15 MPa to 1245.41 ± 83.79 MPa), compressive strength (from 26.59 ± 0.80 MPa to 21.83 ± 1.01 MPa), and Poisson’s ratio (from 0.32 to 0.30). A 40% mass reduction (form 100% to 25% infill density) resulted in a 56% decrease in tensile strength and a 53% decrease in Young’s modulus. A 31% mass reduction was observed for compression samples. Stress relaxation decreased significantly from 100% to 75% density, with further reductions having minimal impact. Hydrated samples showed no mechanical changes compared to baseline specimens. (4) Conclusions: Optimizing infill density in 3D-printed PLA parts helps to balance mechanical performance with material efficiency. The best mechanical properties are typically achieved with an infill density of 100%, but results show that decreasing the mass of the part by a reduction in infill density from 75% to 25% does not significantly affect the ability to transfer tensile and compression loads. PLA’s biodegradability makes it a viable alternative to stable polymers. By minimizing material waste and enabling the efficient use of resources, additive manufacturing aligns with the principles of a closed-loop economy, supporting sustainable development. Full article

Perforated materials are widely used in various fields, including in medicine, for example, in trays for placing and storing cutting tools and for sterilizing disposable materials. Currently, the effective elastic modulus of orthopedic plates is higher than the effective elastic modulus of human bone tissue (the effective elastic modulus of bone ranges between 10 and 30 GPa, depending on the type of bone). This difference in effective elastic modulus leads to the phenomenon known as the stress shielding effect, where the bone experiences insufficient mechanical loading. One potential approach to influence the effective elastic modulus of orthopedic plates is through perforations in their design. Stainless steel 316L has garnered significant interest among medical engineering specialists due to its lower weight, higher strength, and superior biocompatibility. The elastic properties of perforated constructions are influenced by their internal quality, dimensions, shapes, and the overall perforation area, making their study important. An experiment was conducted on perforated plates of 316L stainless steel with perforation areas ranging from 3% to 20%. Increasing the perforation area in perforated 316L stainless steel plates (perforated plates had dimensions of 50 mm in height, 20 mm in width, and 1 mm in thickness; hole diameter of 1 mm; and pitch between the holes of 2, 3, 4, and 5 mm) from 3% to 20% resulted in a decrease in Young’s modulus of the perforated plates from 199 GPa to 147.8 GPa, determined using a non-destructive method for determining resonant frequencies using a laser vibrometer. A three-point bending test on the perforated plates confirmed these findings, demonstrating a consistent trend of decreasing Young’s modulus with increasing perforation area, from 194.4 GPa at 3.14% to 142.6 GPa at 19.63%. The three-point bending method was also employed in this study to determine the Young’s modulus of the perforated plates in order to reinforce the obtained results on the elastic properties by determining the resonance frequencies with a laser vibrometer. It was discovered that the Young’s modulus of a perforated plate cannot be determined solely by the perforation area, as it depends on both the perforation diameter and the pitch between the perforations. In addition, finite element method (FEM) simulations were conducted, revealing that increasing perforation diameter and decreasing pitch significantly reduce the Young’s modulus—with values dropping from 201.5 GPa to 72.6 GPa across various configurations. Full article

The mechanical properties of cell scaffolds are strongly influenced by their hydration state. In this study, we investigated the effect of the aqueous phase on the elastic modulus of chitosan hydrogel films using two complementary techniques: uniaxial tensile testing and atomic force microscopy (AFM) nanoindentation. Our results demonstrate that hydration markedly reduced the elastic modulus, decreasing from approximately 2 GPa in dry films to 120 kPa in swollen films, primarily due to the plasticizing effect of water. Moreover, hydrogel films in equilibrium with the aqueous phase exhibited a Young’s modulus three times lower than that of swollen films not in equilibrium. Raman spectroscopy further reveals a solvent “squeeze-out” phenomenon, as evidenced by an increased signal intensity in the 850–1200 cm⁻¹ region for stretched films that were out of swelling equilibrium, whereas equilibrated films showed stable spectral features. These findings highlight the crucial role of hydration dynamics in determining the mechanical behavior of chitosan hydrogel films, offering valuable insights for tailoring their properties in biomedical scaffold applications. Full article

The effect of root canal irrigants on the mechanical properties of dentin is crucial in endodontic treatment planning. While antiseptics such as sodium hypochlorite and EDTA are widely used, their potential to weaken dentin structure remains a concern. Polyhexanide-based formulations may offer a safer alternative. To assess the impact of a polyhexanide-based antiseptic composition, compared to standard irrigants, on the microhardness, Young’s modulus, and elastic deformation energy of dentin. Sixty extracted human teeth were sectioned and polished to prepare dentin samples. Baseline measurements of Vickers microhardness, Young’s modulus, and elastic deformation work were performed using a Microhardness Tester (CSM Instruments, Switzerland) with a Berkovich indenter. Samples were then divided into six groups (n = 10 per group) and exposed to different irrigants (NaCl 0.9%, NaOCl 3%, chlorhexidine 2%, EDTA 17%, and polyhexanide-based solutions—0.1% and 0.2% Lavasept). Post-treatment measurements were performed. Statistical analysis was conducted using non-parametric tests with Bonferroni correction. Sodium hypochlorite (3%) caused the most pronounced reduction in dentin microhardness and mechanical strength, though not always statistically significant. Polyhexanide-based solutions (0.1% and 0.2% Lavasept) showed a milder effect, with statistically significant changes observed only in elastic deformation energy for 0.2% polyhexanide. EDTA treatment led to severe surface destruction, precluding reliable post-treatment measurements. Polyhexanide-based irrigants demonstrated a more favorable impact on dentin mechanical properties compared to traditional irrigants, supporting their potential use in endodontic protocols aimed at preserving dentin integrity. Full article

Background: Diabetics accumulate Advanced Glycation End products (AGEs) such as Nε-(carboxymethyl)lysine (CML) in their skin, which can provoke changes in the skin’s biomechanical properties. The same changes are also observed during aging. Collagen is one of the first targets of glycation, and this leads to the disruption of the dermis, potentially contributing to the skin complications seen in diabetes, like impaired wound healing and the formation of chronic ulcers. We therefore investigated whether it was possible to detect differences in the biomechanical properties of the reticular dermis by comparing C57/BL6 control mice, type 1 and type 2 diabetic mice, and aged mice. Methods: To investigate this, we used an Atomic Force Microscope (a type of local probe microscope used to visualize the surface topography of a sample) to measure the elastic modulus of each skin sample. The elastic modulus is a parameter that describes a tissue’s resistance to elastic deformation when stress is applied. We also determined whether diabetes is associated with the accumulation of AGEs via Western blots. Results: We found that type 2 diabetic mice and aged mice had a stiffer reticular dermis than young control mice. No differences were found in type 1 diabetic mice. The results of the Western blot did not reveal any significant differences in the CML content in different types of mice, although a non-significant increase was found in type 2 diabetic and aged mice. We show that there is a significant positive correlation between the amount of CML in a mouse and the rigidity of its reticular dermis. Conclusions/interpretation: We have demonstrated that increased glycation in mouse skin is correlated with the biomechanical properties of that skin, which explains the wound healing defects diabetic patient’s experience. AFM is therefore a powerful technique that could be used to characterize the mechanical effects of treatments aimed at reducing the level of AGEs in the skin. Full article

Stratlingite is known as one of the hydration products of aluminum-rich cements. Its microstructure and, consequently, mechanical properties, depend on the Al/Si ratio and hydration conditions. The layered structure of stratlingite is characterized as defected, with vacancies in the aluminosilicate layer. This study uses density functional theory calculations on different stratlingite models to show how chemical composition, water content, and structural defects affect its mechanical properties. The developed models represent structures with full occupancy, with little or no content of structural water, and with vacancies in the aluminosilicate layer. It was shown that the full occupancy models have the highest toughness and are strongly anisotropic. The calculated bulk modulus (B_H) of the models with full occupancy was about 40 GPa, being in the typical range for calcium aluminosilicate minerals. The water loss led to an increase in B_H by approximately 40% compared to the models with full occupancy. In contrast, the models with vacancies exhibited a decrease in B_H of about 30%. In models with the high silicon content (Al/Si ratio of 1/4), B_H, Young’s (E_H), and shear (G_H) moduli decreased in a range 15%–30% compared to the models with an Al/Si ratio of 2/3 of Al/Si. Finally, according to Pugh’s ratio (B_H/G_H), which serves as a criterion for brittle–ductile transition (1.8), the models with full occupancy exhibit a brittle behavior, whereas the defected structures are closer to ductile. This could explain the elastic behavior of stratlingite binder in concretes. Generally, the calculations showed that all investigated parameters (chemical composition, water content, and structural defects) have a significant impact on the mechanical properties of stratlingite minerals. Full article

Enhanced hard coatings with exceptional mechanical and thermal qualities have prompted substantial study into multicomponent nitride systems. TiAl(Si)N coatings have emerged as viable possibilities owing to their remarkable hardness, thermal stability, and oxidation resistance. This work involved the fabrication of thickness-varied TiAl(Si)N gradient coatings using reactive magnetron sputtering, employing a controlled modulation of aluminum and silicon content across the film thickness. Three samples, with thicknesses of ~400 nm, ~600 nm, and ~800 nm, were deposited under uniform Ar/N₂ gas flow ratios, and their microstructural, mechanical, and tribological characteristics were rigorously examined. SEM investigation demonstrated a significant change across thicknesses. XRD results validated the emergence of a predominant cubic TiAl(Si)N phase alongside a secondary hexagonal AlN phase, signifying partial phase segregation. The nanoindentation results indicated that Sample 2 exhibited the maximum hardness (~38 GPa) and Young’s modulus (~550 GPa) due to an optimized equilibrium between solid solution strengthening and nanocomposite production. Tribological testing revealed that Sample 1 displayed the lowest and most consistent friction coefficient, corresponding to its superior H/E and H3/E2 ratios, which signify improved elasticity and resistance to plastic deformation. The findings emphasize that the implementation of a compositional gradient, especially in the distribution of Si and Al, markedly affects the microstructure and performance of TiAl(Si)N coatings. Gradient structures enhance the microstructure, optimize hardness, and increase the friction coefficient. Ongoing refinement of gradient profiles and deposition parameters may further improve the characteristics of TiAl(Si)N coatings, facilitating their wider industrial use. Full article

This study presents a comprehensive analytical–numerical approach to determining the elastic–plastic properties of Hybrid Metal Matrix Composites (HMMCs), contrasting with prior research that primarily emphasizes elasticity. Using the finite element method (FEM) and elasticity and plasticity theory, we determined key parameters, including Young’s modulus, Poisson’s ratio, yield strength, and ultimate tensile strength. The method, which also accounts for strain-hardening behavior via the Hollomon model, enables precise simulation of HMMC with randomly distributed reinforcement particles of varying shapes and sizes, offering a realistic representation of the composite microstructure. Verification against the literature confirms the accuracy of the approach in reflecting both elastic and plastic behavior, providing essential insights into the material’s full mechanical response, particularly yield strength and strain-hardening properties, aspects rarely explored in depth in existing studies on HMMCs. Full article

Critical-sized bone defects or CSDs result from bone loss due to trauma, tumor removal, congenital defects, or degenerative diseases. Though autologous bone transplantation is the current gold standard in treating CSDs, its limitations include donor-site morbidity, unavailability of donor bone tissues, risk of infection, and mismatch between the bone geometry and the defect site. Customized scaffolds fabricated using 3D printing and biocompatible materials can provide mechanical integrity and facilitate osseointegration. Ti-6Al-4V (Ti64) is one of the most widely used commercial alloys in orthopedics. To avoid elastic modulus mismatch between bones and Ti64, it is imperative to use porous lattice structures. Ti64 scaffolds with diamond, cubic, and triply periodic minimal surface (TPMS) gyroid lattice architectures were fabricated using selective laser melting (SLM)with pore sizes ranging from 300 to 900 μm using selective laser melting and evaluated for mechanical and biological performance. Increasing pore size led to higher porosity (up to 90.54%) and reduced mechanical properties. Young’s modulus ranged from 13.18 GPa to 1.01 GPa, while yield stress decreased from 478.16 MPa to 14.86 MPa. Diamond and cubic scaffolds with 300–600 μm pores exhibited stiffness within the cortical bone range, while the 900 μm diamond scaffold approached trabecular stiffness. Gyroid scaffolds (600–900 μm) also showed modulus and yield strength within the cortical bone range but were not suitable for trabecular applications due to their higher stiffness. Cytocompatibility was confirmed through leachate analysis and DAPI-stained osteoblast nuclei. The biological evaluation reported maximum cell adherence in lower pore sizes, with gyroid scaffolds showing a statistically significant (p < 0.01) increase in cell proliferation. These findings suggest that 300–600 μm lattice scaffolds offer an optimal balance between mechanical integrity and biological response for load-bearing bone repair. Full article

Soft lithography with microfabricated molds is a widely used manufacturing method. Recent advancements in 3D printing technologies have enabled microscale feature resolution, providing a promising alternative for mold fabrication. It is well established that the curing of PDMS is influenced by parameters such as temperature, time, and curing agent ratio. This study was conducted to address inconsistencies in PDMS curing observed when using different 3D-printed mold materials during the development of a Lab-on-a-Chip (LoC) system, which is typically employed for investigating the effect of hydrodynamic cavitation on blood clot disintegration. To evaluate the impact of mold material on PDMS curing behavior, PDMS was cast into molds made from polylactic acid (PLA), polyethylene terephthalate (PET), resin, and aluminum, and cured at controlled temperatures (55, 65, and 75 °C) for various durations (2, 6, and 12 h). Curing performance was assessed using Soxhlet extraction, Young’s modulus calculations derived from Atomic Force Microscopy (AFM), and complementary characterization methods. The results indicate that the mold material significantly affects PDMS curing kinetics due to differences in thermal conductivity and surface interactions. Notably, at 65 °C, PDMS cured in aluminum molds had a higher Young’s modulus (~1.84 MPa) compared to PLA (~1.23 MPa) and PET (~1.17 MPa), demonstrating that the mold material can be leveraged to tailor the mechanical properties. These effects were especially pronounced at lower curing temperatures, where PLA and PET molds offered better control over PDMS elasticity, making them suitable for applications requiring flexible LoC devices. Based on these findings, 3D-printed PLA molds show strong potential for PDMS-based microdevice fabrication. Full article

Woven composites and natural fiber-reinforced composites both have widespread applications in various industries due to their appealing load-carrying capacity and performance compared to conventionally manufactured composites, such as polymeric composites. Representative volume element (RVE) generation is one of the most effective and widely adopted methods for estimating mechanical performance in current research. This study aims to explore the effects of three significant factors in woven composite RVEs: yarn spacing (from 0.5 mm to 1.5 mm), fabric thickness (from 0.2 to 0.5 mm), and shear angle (from 3.5 to 15 degrees) through finite element methods and statistical analysis to understand their effectiveness in the elastic moduli’s. The validation of this research has been conducted using available literature. The generation of representative volume elements (RVEs) and the calculation of elastic moduli were performed using ANSYS-19, including the material designer feature. The experimental design was carried out using Design-Expert software version 13, which used response surface methodology. The materials selected for this study were jute fiber and epoxy. After obtaining the elastic moduli from the ANSYS material designer, three responses were considered: longitudinal Young’s modulus (E₁₁), in-plane shear modulus (G₁₂), and major Poisson’s ratio (V₁₂). ANOVA (Analysis of Variance) and 3D contour graphs were generated to further analyze and correlate the effects of the selected materials on these responses. These investigations revealed that in comparison to twill structure, plain structure in natural fiber-reinforced woven composites could be a good alternative. Additionally, the findings highlighted that yarn spacing and fabric thickness significantly influence the considered moduli in plain-weave NFRC material RVEs. However, in twill-woven composite RVEs, the effects of yarn spacing, fabric thickness, and shear angle were found to be considerable. Moreover, statistical analysis has found the best combinations for both plain and twill structures, while the yarn spacing was 1 mm, the shear angle was 9.25 degrees, and the fabric thickness was 0.35 mm. Full article

In hot dry rocks (HDRs), hydraulic fracturing is necessary to create enhanced geothermal systems (EGSs) and optimize flow rates between injection and production wells. The geometry of the induced fracture is related to numerous factors, including rock mechanical properties, especially Young’s modulus and Poisson’s ratio. In this paper, we show the influence of Young’s and Poisson’s parameters on fracture geometry in selected HDR-type prospective areas in Poland. Parameters were determined in the laboratory based on drill core samples from granite and sandstone formations using both dynamic and static methods. The results obtained reveal strong differences between dynamic and static values in granite and less diverse results in sandstone. Based on these data, numerical simulations of fracture geometry were carried out, taking into account the variability in the rocks’ elastic parameters. Sensitivity analysis showed that relatively high diversity in the elastic parameters led to a relatively slight impact on the fracture geometry of the tested formations. The influence of Young’s modulus did not exceed 6.5% of the reference half-length and width values for sandstone and 7.3% of the half-length for granite. Variability in the fracture width was significant in granite formation and amounted to 46.4%. The influence of Poisson’s ratio was marginal in both tested types of rocks. The research results, which have not been reported previously, can be considered for the design of hydraulic fracturing operations in enhanced geothermal systems in Poland. Full article

Elastic moduli are important mechanical properties that describe a material’s stiffness and its deformation under elastic loading. In addition to experimental techniques, computational homogenization is commonly used for composite materials to calculate their elastic moduli. This research employs a deep learning algorithm, specifically a Feedforward Neural Network (FNN), to predict the longitudinal and transverse Young’s modulus, shear modulus, and Poisson’s ratio of various unidirectional (UD) composites. The predictions are based on several features, including the names of the composites, Young’s moduli and Poisson’s ratios of the fibers and matrices, and the fiber volume fraction. Initially, 20 different UD composites were selected from the existing literature. ANSYS-19 Material Designer was then utilized to calculate the elastic moduli of these materials while varying the fiber volume fraction from 0.2 to 0.7. This process generated a dataset of 1948 samples, with 80% of the data allocated for training the FNN model and the remaining 20% used to evaluate performance metrics of the test data. These metrics include mean squared error (MSE), root mean squared error (RMSE), mean absolute error (MAE), and R² score. The results indicate that, with optimized hyperparameters, the FNN model can accurately predict the elastic moduli, demonstrating its effectiveness as a tool for calculating the elastic properties of UD composites. Full article