Search Results (7,307)

A novel stainless steel with high Mn and Mo content (much higher than traditional stainless steel), designated CH241SS, was developed as a potential replacement for Cr-Mo-V alloy steel in the cold forging applications of precision industry. Through carbon reduction in an environmentally friendly manner and a two-stage heat treatment process, the hardness of as-cast CH241 was tailored from HRC 37 to HRC 29, thereby meeting the industrial specifications of cold-forged steel (≤HRC 30). X-ray diffraction analysis of the as-cast microstructure revealed the presence of a small amount of ferrite, martensite, austenite, and alloy carbides. After heat treatment, CH241 exhibited a dual-phase microstructure consisting of ferrite and martensite with dispersed Cr(Ni-Mo) alloy carbides. The CH241 alloy demonstrated excellent high-temperature stability. No noticeable softening occurred after 72 h for the second-stage heat treatment. Based on the mechanical and room-temperature tensile fatigue properties of CH241-F (forging material) and CH241-ST (soft-tough heat treatment), it was demonstrated that the CH241 stainless steel was superior to the traditional stainless steel 4xx in terms of strength and fatigue life. Therefore, CH241 stainless steel can be introduced into cold forging and can be used in precision fatigue application. The relevant data include composition design and heat treatment properties. This study is an important milestone in assisting the upgrading of the vehicle and aerospace industries. Full article

In this study, we report an effective, one-step chemical treatment to directly isolate carboxylated cellulose nanocrystals (CCNCs) from a lignocellulosic source using a mixture of peracetic acid and 10% H₂SO₄ solution. We used infrared spectroscopy, X-ray diffraction, dynamic light scattering, atomic force microscopy, and scanning electron microscopy to characterize all the materials. The obtained CCNCs exhibited needle-like shapes with a width of 10–50 nm and a length of 200–500 nm, a high crystalline index (71.3%), and a high content of -COOH groups (~1.405 mmol/g), with a zeta potential value of −48.5 mV. We attributed this to the cooperative effect of strong oxidative agent and strong acid, which makes the removal of all components occur simultaneously in parallel with the partial hydrolysis of amorphous cellulose regions. Our study opens a new, simple approach to directly isolate cellulose nanocrystals from a lignocellulosic source. Full article

PSR B1259-63/LS 2883 is a well-studied gamma-ray binary hosting a pulsar in a 3.4-year eccentric orbit around a Be-type star. Its non-thermal emission spans from radio to TeV energies, exhibiting a significant increase near the periastron passage. This paper is dedicated to the analysis of INTEGRAL observations of the system following its last periastron passage in June 2024. We aim to study the spectral evolution of this gamma-ray binary in the soft (0.3–10 keV) and hard (30–300 keV) X-ray energy bands. We performed a joint analysis of the data taken by INTEGRAL/ISGRI in July–August 2024 and quasi-simultaneous Swift/XRT observations. The spectrum of the system in the 0.3–300 keV band is well described by an absorbed power law with a photon index of $\Gamma =1.42\pm 0.03$. We place constraints on potential spectral curvature, limiting the break energy $E_{\mathrm{b}}>30$ keV for $\Delta \Gamma >0.3$ and cutoff energy $E_{\mathrm{cutoff}}>150$ keV at a 95% confidence level. For one-zone leptonic emission models, these values correspond to electron distribution spectral parameters of $E_{\mathrm{b},\mathrm{e}}>0.8$ TeV and $E_{\mathrm{cutoff},\mathrm{e}}>1.7$ TeV, consistent with previous constraints derived by H.E.S.S. Full article

As a new generation of mobile communication networks, 6G security faces many new security challenges. Vehicle to Everything (V2X) will be an important part of 6G. In V2X, connected and automated vehicles (CAVs) need to frequently share data with other vehicles and infrastructures. Therefore, identity revocation technology in the authentication is an important way to secure CAVs and other 6G scenario applications. This paper proposes an efficient credential revocation scheme with a four-layer architecture. First, a rapid pre-filtration layer is constructed based on the cuckoo filter, responsible for the initial screening of credentials. Secondly, a directed routing layer and the precision judgement layer are designed based on the consistency hash and the dynamic RSA accumulator. By proposing the dynamic expansion of the RSA accumulator and load-balancing algorithm, a smaller and more stable revocation delay can be achieved when many users and terminal devices access 6G. Finally, a trusted storage layer is built based on the blockchain, and the key revocation parameters are uploaded to the blockchain to achieve a tamper-proof revocation mechanism and trusted data traceability. Based on this architecture, this paper also proposes a detailed identity credential revocation and verification process. Compared to existing solutions, this paper’s solution has a combined average improvement of 59.14% in the performance of the latency of the cancellation of the inspection, and the system has excellent load balancing, with a standard deviation of only 11.62, and the maximum deviation is controlled within the range of ±4%. Full article

The object of this study is welded joints of AISI 321 and Ti-6Al-4V, obtained by diffusion welding on developed conical surfaces. The problem of creating bimetallic joints of AISI 321 and Ti-6Al-4V with developed conical contact surfaces, using diffusion welding through an intermediate Electrolytic Tough Pitch Copper (Cu-ETP) copper layer, was solved. The joints were studied using micro-X-ray spectral analysis, microstructural analysis, and mechanical tests. High mutual diffusion of copper and titanium, along with increased concentrations of Cr and V in copper, was detected. The shear strength of the obtained welded joints is 250 MPa and 235 MPa at 30 min and 15 min, respectively, which is higher than the copper layer’s strength (180 MPa). The obtained results are explained by the dislocation diffusion mechanism in the volume of grains and beyond, due to thermal deformations during welding. Under operating conditions of internal pressure and cryogenic temperatures, the strength of the connection is ensured by the entire two-layer structure, and tightness is ensured by a vacuum-tight diffusion connection. The obtained strength of the connection (250 MPa) is sufficient under the specified operating conditions. Analysis of existing solutions in the literature review indicates that industrial application of technology for manufacturing bimetallic adapters from AISI 321 stainless steel and Ti-6Al-4V titanium alloy is limited to butt joints with small geometric dimensions. Studies of the transition zone structure and diffusion processes in bimetallic joints with developed conical contact surfaces enabled determination of factors affecting joint structure and diffusion coefficients. The obtained bimetallic adapters, made of Ti-6Al-4V titanium alloy and AISI 321 stainless steel, can be used to connect titanium high-pressure vessels with stainless steel pipelines. Full article

This study aims to determine the optimal low-temperature stress relieving heat treatment that minimizes residual stresses while preserving corrosion resistance in Laser Powder Bed Fusion (L-PBF) processed Ti6Al4V alloy. Specifically, it investigates the effects of stress relieving at 400 °C, 600 °C, and 800 °C on microstructure, residual stress, and electrochemical performance. Specimens were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), and electrochemical techniques. A novel microcapillary electrochemical method was employed to precisely assess passive layer stability and corrosion behaviour under simulated oral conditions, including fluoride contamination and tensile loading. Results show that heat treatments up to 600 °C effectively reduce residual stress with minimal impact on corrosion resistance. However, 800 °C treatment leads to a phase transformation from α′ martensite to a dual-phase α + β structure, significantly compromising passive film integrity. The findings establish 600 °C as the optimal stress-relieving temperature for balancing mechanical stability and electrochemical performance in biomedical and aerospace components. Full article

M-edge X-ray absorption spectroscopy (XAS), which probes 3p→3d transitions in first-row transition metals, provides detailed insights into oxidation states, spin-states, and local electronic structure with high element and orbital specificity. Operating in the extreme ultraviolet (XUV) region, this technique provides sharp multiplet-resolved features with high sensitivity to ligand field and covalency effects. Compared to K- and L-edge XAS, M-edge spectra exhibit significantly narrower full widths at half maximum (typically 0.3–0.5 eV versus >1 eV at the L-edge and >1.5–2 eV at the K-edge), owing to longer 3p core-hole lifetimes. M-edge measurements are also more surface-sensitive due to the lower photon energy range, making them particularly well-suited for probing thin films, interfaces, and surface-bound species. The advent of tabletop high-harmonic generation (HHG) sources has enabled femtosecond time-resolved M-edge measurements, allowing direct observation of ultrafast photoinduced processes such as charge transfer and spin crossover dynamics. This review presents an overview of the fundamental principles, experimental advances, and current theoretical approaches for interpreting M-edge spectra. We further discuss a range of applications in catalysis, materials science, and coordination chemistry, highlighting the technique’s growing impact and potential for future studies. Full article

Background/Objectives: Cystic fibrosis (CF) is a rare autosomal recessive genetic disease that has a progressive and multisystemic course. The spectrum and frequency of mutations in the gene encoding the cystic fibrosis transmembrane conductance regulator (CFTR) vary both in European countries and in other geographical regions. The aim of our retrospective study was to present the genetic variants identified in a group of 48 CF patients from the Moldova region (Romania), as well as to establish genotype–phenotype correlations. Methods: Genetic testing was initially performed for 38 CFTR mutations, and in heterozygous patients or those in whom no mutation was detected, CFTR gene sequencing (NGS) was performed. Results: The compound heterozygous genotype was identified in 26 (54.16%) of the patients (with one of the alleles being F508del), while 22 (45.83%) patients had the homozygous F508del genotype. The F508del variant was the most frequent (69.79%), followed by G542X (6.25%, 6/96). Several new variants were also identified that had not been reported in other studies from Romania (R1158X, K598*, R347H, c.2589_2599del, R496H, and CFTRdele2). Phenotypic manifestations in patients with CFTR class I, II, III and VII variants (homozygous and compound heterozygous) were more severe compared to those in patients with CFTR class IV, V and VI mutations, with the data obtained being consistent with those in the literature. Respiratory tract involvement was present in 77.08% of the patients, being more frequent in patients with the compound heterozygous genotype compared to the homozygous F508del genotype. Most patients had exocrine pancreatic insufficiency (EPI) (85.41%). Gastrointestinal manifestations included hepatocytolysis (66.66%) and biliary cirrhosis (0.41%). Meconium ileus was detected in 18.75% of patients, all with a compound heterozygous genotype. Conclusions: We compared the results obtained with data from the literature and correlated the detected CFTR variant (genotype) with the phenotypic manifestations, highlighting certain particularities present in some patients. Genetic testing allows for early diagnosis and adapted management, including personalized treatment for each patient. Identification of novel unclassified CFTR variants still remains a challenge for clinicians. NGS-based screening of heterozygous healthy carriers is important for both genetic counseling and prenatal diagnosis. Full article

The rapid growth of Internet of Things (IoT) deployment has led to an unprecedented volume of interconnected, resource-constrained devices. Securing their communication is essential, especially in vehicular environments, where sensitive data exchange requires robust authentication, integrity, and confidentiality guarantees. In this paper, we present an empirical evaluation of TLS (Transport Layer Security)-enhanced MQTT (Message Queuing Telemetry Transport) on low-cost, quad-core Cortex-A72 ARMv8 boards, specifically the Raspberry Pi 4B, commonly used as prototyping platforms for On-Board Units (OBUs) and Road-Side Units (RSUs). Three MQTT entities, namely, the broker, the publisher, and the subscriber, are deployed, utilizing Elliptic Curve Cryptography (ECC) for key exchange and authentication and employing the AES_256_GCM and ChaCha20_Poly1305 ciphers for confidentiality via appropriately selected libraries. We quantify resource consumption in terms of CPU utilization, execution time, energy usage, memory footprint, and goodput across TLS phases, cipher suites, message packaging strategies, and both Ethernet and WiFi interfaces. Our results show that (i) TLS 1.3-enhanced MQTT is feasible on Raspberry Pi 4B devices, though it introduces non-negligible resource overheads; (ii) batching messages into fewer, larger packets reduces transmission cost and latency; and (iii) ChaCha20_Poly1305 outperforms AES_256_GCM, particularly in wireless scenarios, making it the preferred choice for resource- and latency-sensitive V2X applications. These findings provide actionable recommendations for deploying secure MQTT communication on an IoT platform. Full article

In our study, supercapacitor electrodes were prepared by depositing electroless Ni-B coating on copper plates, followed by nitric acid etching. The composition and the micro- and phase structure of the coatings were investigated by ICP-OES, PFIB-SEM, and XRD techniques. The original pebble-like structure of the coating consists of 0.8–10 µm particles, with an X-ray amorphous phase structure. The surface morphology and porosity of the coating can be tuned simply by changing the etching time. The supercapacitive performance of the electrodes was evaluated by means of cyclic voltammetry, galvanostatic charge–discharge, and electrochemical impedance spectroscopy measurements. The capacitance of the coating was found to vary on the etching time according to a maximum function, allowing for the determination of an optimal duration to obtain a specific capacitance of 157 mF/cm² (at 0.5 A/g). An excellent charge storage retention of 178% was found after 5000 CV cycles at a scan rate of 50 mV/s owing to the evolved electrochemically active network on the surface of the electrode, indicating a long-term stable and reliable electrode. Full article

This study systematically evaluates the influence of copper (Cu) addition in gas-shielded solid wires on the microstructure and cryogenic toughness of X80 pipeline steel welds. Welds were fabricated using solid wires with varying Cu contents (0.13–0.34 wt.%) under identical gas metal arc welding (GMAW) parameters. The mechanical capacities were assessed via tensile testing, Charpy V-notch impact tests at −20 °C and Vickers hardness measurements. Microstructural evolution was characterized through optical microscopy (OM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). Key findings reveal that increasing the Cu content from 0.13 wt.% to 0.34 wt.% reduces the volume percentage of acicular ferrite (AF) in the weld metal by approximately 20%, accompanied by a significant decline in cryogenic toughness, with the average impact energy decreasing from 221.08 J to 151.59 J. Mechanistic analysis demonstrates that the trace increase in the Cu element. The phase transition temperature and inclusions is not significant but can refine the prior austenite grain size of the weld, so that the total surface area of the grain boundary increases, and the surface area of the inclusions within the grain is relatively small, resulting in the nucleation of acicular ferrite within the grain being weak. This microstructural transition lowers the critical crack size and diminishes the density for high-angle grain boundaries (HAGBs > 45°), which weakens crack deflection capability. Consequently, the crack propagation angle decreases from 54.73° to 45°, substantially reducing the energy required for stable crack growth and deteriorating low-temperature toughness. Full article

The impact of 230-MeV Xe¹³² ion irradiation on the structural, optical, and luminescent properties of YAG:Ce single crystals is investigated over a fluence range of 10¹¹–10¹⁴ ions/cm². Optical absorption; cathodo-, X-ray, and photoluminescence; and X-ray diffraction are employed to analyze radiation-induced changes. Irradiation leads to the formation of Frenkel (F, F⁺) and antisite defects and attenuates Ce³⁺ emission (via enhanced nonradiative processes and Ce³⁺ → Ce⁴⁺ recharging). A redistribution between the fast and slow components of the Ce³⁺-emission is considered. Excitation spectra show the suppression of exciton-related emission bands, as well as a shift of the excitation onset due to increased lattice disorder. XRD data confirm partial amorphization and a high level of local lattice disordering, both increasing with irradiation fluence. These findings provide insight into radiation-induced processes in YAG:Ce, which are relevant for its application in radiation–hard scintillation detectors. Full article

Supercapacitors are considered a bridge between batteries and capacitors due to their significant energy density, as well as power density. Herein, we prepared two novel electrodes of Fe_0.8Co_0.2S and Fe_0.8Co_0.2S/rGO composites and analyzed their supercapacitor performance. The results indicated that Fe_0.8Co_0.2S/rGO, prepared through co-precipitation and annealing, exhibited a higher specific capacitance value and improved electrochemical properties in comparison to Fe_0.8Co_0.2S due to the synergistic effect of rGO with Fe_0.8Co_0.2S. X-ray diffraction (XRD) confirmed the desired phases of Fe_0.8Co_0.2S, while scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) verified the microstructures and desired elements. Cyclic voltammetry (CV) confirmed an enhanced oxidation current from +25 mA to +49 mA at 10 mV/s, while galvanometric charge–discharge (GCD) showed an enhanced discharge time from 78 s to 300 s. As a result, the specific capacitance and energy density were enhanced from 74.3 F/g to 285.7 F/g and 2.84 Wh/kg to 10.9 Wh/kg, respectively. This contributed to a more than 283% increase in specific capacitance, as well as energy density. Overall, Fe_0.8Co_0.2S/rGO shows great potential for small-scale energy storage devices. Full article

Pyrochlore Bi_1.8Mn_0.5Ni_0.5Ta₂O_9-Δ (sp.gr. Fd-3m, a = 10.5038(9) Å) was synthesized by the solid-phase reaction method and characterized by vibrational and X-ray spectroscopy. According to scanning electron microscopy, the ceramics are characterized by a porous microstructure formed by randomly oriented oblong grains. The average crystallite size determined by X-ray diffraction is 65 nm. The charge state of transition element cations in the pyrochlore was analyzed by soft X-ray spectroscopy using synchrotron radiation. For mixed pyrochlore, a characteristic shift of Bi4f and Ta4f and Ta5p spectra to the region of lower energies by 0.25 and 0.90 eV is observed compared to the binding energy in Bi₂O₃ and Ta₂O₅ oxides. XPS Mn2p spectrum of pyrochlore has an intermediate energy position compared to the binding energy in MnO and Mn₂O₃, which indicates a mixed charge state of manganese (II, III) cations. Judging by the nature of the Ni2p spectrum of the complex oxide, nickel ions are in the charge state of +(2+ζ). The relative permittivity of the sample in a wide temperature (up to 350 °C) and frequency range (25–10⁶ Hz) does not depend on the frequency and exhibits a constant low value of 25. The minimum value of 4 × 10⁻³ dielectric loss tangent is exhibited by the sample at a frequency of 10⁶ Hz. The activation energy of conductivity is 0.7 eV. The electrical behavior of the sample is modeled by an equivalent circuit containing a Warburg diffusion element. Full article

The influence of the copper (Cu) content on the corrosion resistance of 3.5%Ni low-carbon weathering steel was investigated using periodic dry–wet cycle accelerated corrosion tests. The mechanical properties of the steels were assessed via tensile and low-temperature impact tests, while corrosion resistance was evaluated based on weight loss measurements. Surface oxide layers were characterized using three-dimensional laser confocal microscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and electrochemical methods. Electron probe microanalysis (EPMA) was employed to examine the cross-sectional morphology of the oxide layer after 72 h of accelerated corrosion tests. The results indicate that the solution state of Cu increased the strength of 3.5%Ni steels but significantly damaged the low-temperature toughness. As the Cu content increased from 0.75% to 1.25%, the corrosion rate decreased from 4.65 to 3.74 g/m² h. However, when there was a further increase in the Cu content to 2.15%, there was little decrease in the corrosion rate. With the increase in the Cu content from 0.75% to 2.15%, the surface roughness of 3.5%Ni weathering steel after corrosion decreased from 5.543 to 5.019 μm, and the corrosion behavior was more uniform. Additionally, the α/γ protective factor of the oxide layer of the surface layer increased from 2.58 to 2.84 with an increase in the Cu content from 0.75% to 1.25%, resulting in the oxide layer of the surface layer being more protective. For 1.25%Cu steel, the corrosion current density of rusted samples is lower (ranging from 1.2609 × 10⁻⁴ A/cm² to 3.7376 × 10⁻⁴ A/cm²), and the corrosion potential is higher (ranging from −0.85544 V to −0.40243 V). Therefore, the rusted samples are more corrosion resistant. The Cu in the oxide layer of the surface layer forms CuO and CuFeO₂, which are helpful for increasing corrosion resistance, which inhibits the penetration of Cl⁻. Full article