Search Results (371)

Objective: This study aimed to evaluate the in vitro efficacy of silver nanoparticles (AgNPs) synthesized by bioreduction using lemongrass (Cymbopogon citratus) essential oil against multidrug-resistant (MDR) bacteria isolated from an Intensive Care Unit (ICU). Methods: The essential oil was extracted and characterized by gas chromatography–mass spectrometry (GC-MS). Antioxidant activity was assessed using the 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging assay, the 2,2′-azino-bis (3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) assay, and total phenolic content. AgNPs (3 mM and 6 mM silver nitrate) were characterized by UV-Vis spectroscopy, dynamic light scattering (DLS), zeta potential, transmission electron microscopy (TEM), and Fourier-transform infrared (FTIR) spectroscopy. Bacterial isolates were obtained from ICU surfaces and personal protective equipment (PPE). Results: The essential oil presented citral A, citral B, and β-myrcene as major components (97.5% of identified compounds). AgNPs at 3 mM showed smaller size (87 nm), lower Polydispersity Index (0.14), and higher colloidal stability (−23 mV). The 6 mM formulation (147 nm; PDI 0.91; −10 mV) was more effective against a strain of Enterococcus spp. resistant to all antibiotics tested. FTIR analysis indicated the presence of O–H, C=O, and C–O groups involved in nanoparticle stabilization. Discussion: The higher antimicrobial efficacy of the 6 mM formulation was attributed to the greater availability of active AgNPs. Conclusions: The green synthesis of AgNPs using C. citratus essential oil proved effective against MDR bacteria and represents a sustainable and promising alternative for microbiological control in healthcare environments. Full article

In this study, lanthanum–nitrogen co-doped titanium dioxide (La-N-TiO₂) thin films were fabricated using Ion Beam Assisted Deposition (IBAD) and subjected to accelerated ultraviolet (UV) aging experiments to systematically investigate the impact of co-doping on the films’ resistance to UV aging. X-ray diffraction (XRD) analysis revealed that La-N co-doping inhibits the phase transition from anatase to rutile, significantly enhancing the phase stability of the films. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) characterizations indicated that co-doping increased the density and surface uniformity of the films, thereby delaying the expansion of cracks and increase in roughness induced by UV exposure. Energy-dispersive X-ray spectroscopy (EDS) results confirmed the successful incorporation of La and N into the TiO₂ lattice, enhancing the chemical stability of the films. Contact angle tests demonstrated that La-N co-doping markedly improved the hydrophobicity of the films, inhibiting the rapid decay of hydrophilicity during UV aging. After three years of UV aging, the co-doped films maintained high structural integrity and photocatalytic performance, exhibiting excellent resistance to UV aging. These findings offer new insights into the long-term stability of photovoltaic self-cleaning materials. Full article

This review article focuses on the long-term durability challenges associated with bamboo fiber-reinforced polymer composites when subjected to various environmental aging conditions such as water immersion, hygrothermal fluctuations, ultraviolet (UV) radiation, soil burial, and refrigerated storage. The primary issue addressed is the degradation of mechanical and structural performance of bamboo fiber-reinforced polymer composites due to moisture absorption, fiber swelling, and fiber–matrix interface deterioration. To mitigate these aging effects, the study evaluates and compares multiple strategies, including chemical and physical fiber surface treatments, filler additions, and fiber hybridization, which aim to enhance moisture resistance and mechanical stability. These composites are relevant in automotive interiors, construction panels, building insulation, and consumer goods due to their eco-friendly nature and potential to replace conventional synthetic composites. This review is necessary to consolidate current knowledge, identify effective enhancement approaches, and guide the development of environmentally resilient bamboo fiber-reinforced polymer composites for real-world applications. Full article

The superhydrophobic coatings for outdoor use need to be exposed to sunlight for a long time; therefore, their UV-aging resistances are crucial in practical applications. In this study, the primary product of titanium dioxide (P-TiO₂) was used as the raw material. Nano-silica (SiO₂) was coated onto the surface of P-TiO₂ by the acid precipitation method to prepare P-TiO₂-SiO₂ composite particles. Then, they were modified and sprayed simply to obtain a superhydrophobic P-TiO₂-SiO₂/HDTMS coating. The results indicated that amorphous nano-SiO₂ was coated on the P-TiO₂ surface, forming a micro–nano binary structure, which was the essential structure to form superhydrophobic coatings. Additionally, the UV-aging property of P-TiO₂ was significantly enhanced after being coated with SiO₂. After continuous UV irradiation for 30 days, the color difference (ΔE*) and yellowing index (Δb*) values of the coating prepared with P-TiO₂-SiO₂ increased from 0 to 0.75 and 0.23, respectively. In contrast, the ΔE* and Δb* of the coating prepared with P-TiO₂ increased from 0 to 1.68 and 0.74, respectively. It was clear that the yellowing degree of the P-TiO₂-SiO₂ coating was lower than that of P-TiO₂, and its UV-aging resistance was significantly improved. After modification with HDTMS, the P-TiO₂-SiO₂ coating formed a superhydrophobic P-TiO₂-SiO₂/HDTMS coating. The water contact angle (WCA) and water slide angle (WSA) on the surface of the coating were 154.9° and 1.3°, respectively. Furthermore, the coating demonstrated excellent UV-aging resistance. After continuous UV irradiation for 45 days, the WCA on the coating surface remained above 150°. Under the same conditions, the WCAs of the P-TiO₂/HDTMS coating decreased from more than 150° to 15.3°. This indicated that the retention of surface hydrophobicity of the P-TiO₂-SiO₂/HDTMS coating was longer than that of P-TiO₂/HDTMS, and the P-TiO₂-SiO₂/HDTMS coating’s UV-aging resistance was greater. The superhydrophobic P-TiO₂-SiO₂/HDTMS self-cleaning coating reported in this study exhibited outstanding UV-aging resistance, and it had the potential for long-term outdoor use. Full article

This study focuses on the influence of prolonged ultraviolet (UV) irradiation on the mechanical properties and surface microstructure of glass fiber-reinforced plastics (GFRPs) and basalt fiber-reinforced plastics (BFRPs), which are widely used in construction and transport infrastructure. The relevance of the research lies in the need to improve the reliability of composite materials under extended exposure to harsh climatic conditions. Experimental tests were conducted in a laboratory UV chamber over 2000 h, simulating accelerated weathering. Mechanical properties were evaluated using three-point bending, while surface conditions were assessed via profilometry and microscopy. It was shown that GFRPs exhibit a significant reduction in flexural strength—down to 59–64% of their original value—accompanied by increased surface roughness and microdefect depth. The degradation mechanism of GFRPs is attributed to the photochemical breakdown of the polymer matrix, involving free radical generation, bond scission, and oxidative processes. To verify these mechanisms, FTIR spectroscopy was employed, which enabled the identification of structural changes in the polymer phase and the detection of mass loss associated with matrix decomposition. In contrast, BFRP retained up to 95% of their initial strength, demonstrating high resistance to UV-induced aging. This is attributed to the shielding effect of basalt fibers and their ability to retain moisture in microcavities, which slows the progress of photo-destructive processes. Comparison with results from natural exposure tests under extreme climatic conditions (Yakutsk) confirmed the reliability of the accelerated aging model used in the laboratory. Full article

This study investigates the effect of accelerated aging on the microstructure and surface properties of synthetic sports surfaces, with the goal of developing a more representative laboratory simulation method. Three common types of polyurethane-based sports surfaces were examined: (1) a dual-layer SBR base with a thin EPDM spray topcoat; (2) a single-layer EPDM surface with a smooth finish; and (3) a dual-layer “sandwich” structure with a rough EPDM upper layer. Samples were tested for slip resistance (PTV), abrasion resistance, and surface morphology using SEM, as well as surface roughness and tensile properties before and after aging. Method combining UV radiation and water spray was introduced and evaluated. Microstructural analysis with roughness measurements revealed surface degradation in all materials, with more extensive damage observed in the UV + spray cycle. Slip resistance results showed reduced performance in dry conditions and improved values in wet conditions post-aging. The single-layer EPDM surface demonstrated the highest initial dry PTV, while the dual-layer with spray had the lowest. After aging, all surfaces exhibited smaller differences between dry and wet performance but no longer met dry condition standards. These results may guide future revisions of performance testing standards and contribute to the development of safer, longer-lasting synthetic sports surfaces. Full article

Honey, propolis or royal jelly are considered natural remedies with therapeutic properties since antiquity. Many papers explore the development of antimicrobial biomaterials based on individual bee products, but there is a lack of studies on their synergistic effects. Combining honey, propolis and royal jelly with silver nanoparticles in a biopolymer matrix offers a synergistic strategy to combat antibiotic-resistant bacterial infections. This approach supports progress in wound healing, soft tissue engineering and other domains where elimination of the microorganisms is needed like food packaging. In this study we have obtained antimicrobial films based on bee products and silver nanoparticles (AgNPs) incorporated in an alginate–chitosan blend. The novel biomaterials were analyzed by UV-Vis, fluorescence and FTIR spectroscopy or microscopy, SEM and thermal analysis. Antibacterial tests were conducted against both Gram-positive and Gram-negative bacteria, while the antifungal properties were tested against Candida albicans. The diameters for growth inhibition zones were up to 10 mm for bacterial strains and 8 mm for the fungal strain. Additionally, cytotoxicity assays were performed to evaluate the biocompatibility of the materials, the results indicating that the combination of honey, propolis, royal jelly and AgNPs does not produce synergistic toxicity. Full article

Skin cancers are associated with a significant psychological burden across all age groups, particularly as their global incidence continues to rise. Ultraviolet (UV) radiation—primarily UVA and UVB—remains the leading etiological factor, inducing DNA mutations in key genes such as TP53 and BRAF. Among skin cancers, basal cell carcinoma (BCC) is the most prevalent and typically indolent. In contrast, squamous cell carcinoma (SCC) tends to be more invasive, while melanoma is the most aggressive and prone to metastasis. Melanoma is especially concerning due to its rapid dissemination and its occurrence not only on the skin but also in ocular, mucosal, and nail tissues. These challenges, along with rising treatment resistance and mortality, underscore the urgent need for novel anticancer agents. Berberine—a plant-derived isoquinoline alkaloid—has attracted increasing attention for its broad-spectrum anticancer potential, including against skin cancers. In this review, we summarize current evidence regarding berberine’s mechanisms of action in melanoma and SCC, emphasizing both its preventive and therapeutic effects. We further explore its potential as an adjuvant agent in combination with conventional treatments, offering a promising avenue for enhancing the clinical outcomes of skin cancer therapy. Full article

Prolonged ultraviolet (UV) exposure accelerates aging and degradation, while conventional constant-intensity UV simulations do not reflect the variable nature of outdoor radiation. Aging duration and film thickness are both key factors affecting Rubber-Modified Asphalt (RMA), but how their combination influences RMA remains unclear. To address this limitation, this research employed accelerated aging experiments under variable-intensity UV radiation to investigate the performance and aging mechanism of RMA across different aging durations and asphalt film thicknesses. Rheological properties were analyzed through rheological tests, and the UV aging mechanisms of RMA were revealed using FTIR and SEM. The results revealed that crumb rubber improved RMA’s UV aging resistance, including high-temperature performance, fatigue life, and low-temperature cracking resistance. Aging effects were more influenced in RMA with thinner films under prolonged UV exposure. After nine cycles of ultraviolet aging, the rutting resistance, elastic recovery, fatigue life, and low-temperature cracking resistance of RMA with a 1 mm film thickness were 1.33, 1.11, 0.54, and 0.67 times, respectively, those of RMA with a 2 mm film thickness subjected to three UV aging cycles. RMA demonstrated comparable high-temperature performance and elastic recovery under UV aging conditions corresponding to a 1.5 mm film thickness aged for three cycles and a 2.0 mm film thickness aged for six cycles, as well as a 1.0 mm film thickness aged for six cycles and a 1.5 mm film thickness aged for nine cycles. FTIR showed that the increased activity of C=C and C-H under photo-oxidative aging caused a greater impact on the carbonyl groups than the sulfoxide groups. Under high-intensity UV radiation, RMA with thinner films exhibited greater rubber powder detachment, increased surface oxidation, and a substantial widening of cracks. The rubber powder absorbed UV radiation, enhancing the stability of RMA. The maximum crack width of the 1 mm NA was twice that of RMA. These provided insight into the microstructural pattern of cracking resistance degradation caused by aging. This research provides theoretical support for the optimization of the anti-aging performance of RMA. Full article

The purpose of current study was the green synthesis of bioactive silver nanoparticles (AgNPs) using Brevibacillus sp. MAHUQ-41 and the exploration of their role in controlling drug-resistant bacterial pathogens Listeria monocytogenes and Yersinia enterocolitica. The culture supernatant of strain MAHUQ-41 was employed for a simple and eco-friendly synthesis of biofunctional silver nanoparticles (AgNPs). The resulting nanoparticles were analyzed using several techniques, including UV–Visible spectroscopy, XRD, FE-TEM, FTIR, and DLS. The UV–Vis spectral analysis of the AgNPs synthesized via Brevibacillus sp. MAHUQ-41 revealed a prominent absorption peak at 400 nm. FE-TEM results confirmed spherical-shaped 15–60 nm sized nanoparticles. XRD results indicated that the synthesized AgNPs were crystalline in nature. The FTIR spectrum determined various functional groups on the surface of synthesized nanoparticles. Potent antibacterial properties were observed in green-synthesized AgNPs against tested pathogens. The MIC value of extracellular synthesized AgNPs for both pathogenic bacteria was 6.2 µg/mL, and the MBCs were 25.0 µg/mL and 12.5 µg/mL for L. monocytogenes and Y. enterocolitica, respectively. Treatment by synthesized AgNPs resulted in morphological alterations and structural damages in both L. monocytogenes and Y. enterocolitica. These alterations can interfere with regular cellular activities, potentially resulting in cell death. This study is the first to report the antimicrobial properties of silver nanoparticles synthesized using Brevibacillus sp. MAHUQ-41. The findings obtained in the present study supported the role of Brevibacillus sp. MAHUQ-41-mediated synthesized AgNPs in controlling drug-resistant bacterial pathogens L. monocytogenes and Y. enterocolitica. Full article

Recently, the urgency of combating antibiotic-resistant bacteria, viruses, and other pathogens has dramatically increased. With the development of nanotechnology, significant hopes are placed on nanoparticles with antimicrobial properties. The efficiency of such materials can be significantly enhanced through light-activated processes. In this study, we prepared composite ZnO-Ag nanoparticles and tested their ability to inhibit Staphylococcus aureus bacteria. The composite ZnO-Ag nanoparticles were fabricated using pulsed laser ablation of Zn and Ag targets in water using a nanosecond pulsed laser. During antibacterial tests, light-enhanced activation of the nanoparticles was achieved using low-power near UV (375 nm) and blue visible (410 nm) LED irradiation. For comparison, similar laser-fabricated ZnO nanoparticles were also tested. The combined use of nanoparticles and LED irradiation significantly increased the generation of reactive oxygen species. As a result, low nanoparticle concentrations (0.05 g/L) and low-power LED irradiation (0.17–0.22 W) significantly reduced the concentration of Staphylococcus aureus bacteria, including experiments with visible light irradiation. Compared to their ZnO counterparts, the use of ZnO-Ag composite particles led to an additional increase in antimicrobial activity. Full article

Sheep wool is a natural fiber from various sheep breeds, mainly used in clothing for its insulation properties. It makes up a small share of global fiber production, which is declining as synthetic fibers replace wool and meat farming becomes more profitable. Wool from slaughter sheep, often unsuitable for textiles, is treated as biodegradable waste. The aim of the study was to develop a fully biodegradable composite of natural origin from a polylactide (PLA) matrix reinforced with sheep wool and to select the optimal modifications (chemical) of sheep wool fibers to obtain modified properties, including mechanical properties. The behavior of the composites after exposure to aging conditions simulating naturally occurring stimuli causing biodegradation and thus changes in the material’s performance over its lifespan was also examined. Dynamic thermal analysis was used to describe and parameterize the obtained data and their variables, and the mechanical properties were investigated. The research culminated in a microscopic analysis along with changes in surface properties. The study demonstrated that wool-reinforced composites exhibited significantly improved resistance to UV degradation compared to pure PLA, with samples containing 15% unmodified wool showing a 54% increase in storage modulus at 0 °C after aging. Chemical modifications using nitric acid, iron compounds, and tar were successfully implemented to enhance fiber–matrix compatibility, resulting in increased glass transition temperatures and modified mechanical properties. Although wool fiber is not a good choice for modifications to increase mechanical strength, adding wool fiber does not improve mechanical properties but also does not worsen them much. Wool fibers are a good filler that accelerates degradation and are also a waste, which reduces the potential costs of producing such a biocomposite. The research established that these biocomposites maintain sufficient mechanical properties for packaging applications while offering better environmental resistance than pure polylactide, contributing to the development of circular economy solutions for agricultural waste valorization. So far, no studies have been conducted in the literature on the influence of sheep wool and its modified versions on the mechanical properties and the influence of modification on the degradation rate of PLA/sheep wool biocomposites. Full article

Star polymers—macromolecules featuring multiple arms radiating from a central core—offer unique potential for biomedical applications due to their tunable architecture, multifunctionality and ability to incorporate stimuli-responsive and biocompatible components. In this study, functional star polymers with oligo (ethylene glycol) methyl ether methacrylate (OEOMA) arms and 2-(dimethylamino)ethyl methacrylate (DMAEMA) core units were synthesized via atom transfer radical polymerization (ATRP) using the “arm-first” strategy. The star polymers were used as nanoreactors for the in situ reduction of silver nitrate to form silver nanoparticles (AgNPs) without additional reducing agents. UV–Vis spectroscopy confirmed the formation of spherical AgNPs with absorption maxima around 430 nm, and transmission electron microscopy revealed uniform particle morphology. These hybrid nanomaterials (STR-AgNPs) were incorporated into polymethyl methacrylate (PMMA)-based bone cement to impart antibacterial properties. Mechanical testing showed that the compressive strength remained within acceptable limits, while antibacterial assays against E. coli demonstrated a significant inhibition of bacterial growth. These findings suggest that STR-AgNPs serve as promising candidates for infection-resistant bone implants, providing localized antibacterial effects while maintaining mechanical integrity and biocompatibility. Full article

This study presents the successful fabrication of lead zirconate titanate (PZT) thin films on silicon (Si) substrates using a hybrid deposition method combining spin-coating and RF sputtering techniques. Initially, a PZT layer was deposited through four successive spin-coating cycles, followed by an additional layer formed via RF sputtering. The resulting multilayer structure was annealed at ${700 }^{°}$C for 2 h to improve crystallinity. Comprehensive material characterization was conducted using XRD, SEM, cross-sectional SEM, EDX, and UV–VIS absorbance spectroscopy. The analyses confirmed the formation of a well-crystallized perovskite phase, a uniform surface morphology, and an optical band gap of approximately 3.55 eV, supporting its suitability for sensing applications. Building upon these findings, a multilayer PZT-based touch sensor was fabricated and electrically characterized. Low-frequency I–V measurements demonstrated consistent and repeatable polarization behavior under cyclic loading conditions. In addition, $\left|Z\right|$–f measurements were performed to assess the sensor’s dynamic electrical behavior. Although expected dielectric responses were observed, the absence of distinct anti-resonance peaks suggested non-idealities linked to ${\mathrm{Ag}}^{+}$ ion diffusion from the electrode layers. To account for these effects, the classical Butterworth–Van Dyke (BVD) equivalent circuit model was extended with additional inductive and resistive components representing parasitic pathways. This modified model provided excellent agreement with the measured impedance and phase data, offering deeper insight into the interplay between material degradation and electrical performance. Overall, the developed sensor structure exhibits strong potential for use in piezoelectric sensing applications, particularly for tactile and pressure-based interfaces. Full article

This study investigates the effects of destructive climatic factors on the mechanical and performance properties of various structural materials, encompassing both polymers and metals. Over recent decades, the growing adoption of synthetic polymers has revolutionized engineering applications, yet their susceptibility to environmental degradation poses significant challenges. This research emphasizes the need for comprehensive testing under both operational and environmental stressors, including extreme temperatures, UV radiation, and moisture, to assess material durability and performance. Mechanical tests were conducted at ambient (25 °C) and low temperatures (−50 °C) to evaluate the strength and strain responses of selected materials. Additionally, a 12-month accelerated aging process using UV radiation and elevated temperatures was performed to simulate long-term environmental exposure. Parameters such as Shore D hardness, gloss, and mass were measured at regular intervals to quantify material degradation. The results revealed significant differences in performance across material types. Among polymers, laser-extruded and milky plexiglass, as well as solid polycarbonate, exhibited satisfactory resistance to aging, with minimal changes in mechanical properties. However, high-impact polystyrene displayed substantial deformation and hardness loss after prolonged UV exposure. For metals, aluminum and stainless steel (304 and 316) demonstrated exceptional durability, retaining structural and aesthetic properties after 12 months of accelerated aging, whereas galvanized steel exhibited pronounced corrosion. The study highlights the critical interplay between mechanical loading and environmental factors, stressing the importance of material selection tailored to specific climatic conditions. It further underscores the value of integrating experimental findings with predictive models, such as finite element analysis, to enhance the design and longevity of engineering materials. The findings provide actionable insights for industries operating in temperate climates, where materials are subjected to diverse and cyclic environmental stressors. Recommendations are offered for selecting resilient materials suitable for protective housings and structural components. Full article