Search Results (537)

The influence of different heat treatment processes on the microstructure and mechanical properties of 18Ni350 maraging steel manufactured by selective laser melting and the corrosion resistance of TiB₂ ceramic coatings Electro-Spark-Deposited on its surface when immersed in high-temperature molten aluminum have been investigated in the present study. The microstructures and mechanical properties of the differently heat-treated samples were analyzed using various precision instruments. The results reveal that the as-built sample exhibits a microstructure composed of cellular and columnar dendritic grains. After solution treatment, the microstructure fully transforms into lath-like martensite. After direct aging treatment, the cellular structures diminish, while precipitates at grain boundaries proliferate with increasing aging temperature. SAT- treatment achieves full microstructural homogenization, featuring fine-lath martensite and a small amount of randomly distributed austenite particles. DA- and SAT- significantly improve the strength, hardness and modulus of samples and were found to reduce the toughness and plasticity. After solution treatment at 800 °C for 1 h followed by aging treatment at 520 °C for 6 h (SAT 800-520), the specimen achieved an UTS of 2476 MPa while maintaining an EL of 4.6%. The TiB₂ coating and the Cr interlayer deposited via ESD form a continuous interfacial bond with the substrate, demonstrating favorable adhesion. After 4 h of static immersion in high-temperature molten aluminum, the coating remains intact without complete delamination, delivering effective protection to the substrate. Full article

Quenched and tempered (Q+T) bolt steels are widely used in key load-bearing structures such as bridges, wind power equipment, pressure vessels and engineering machinery, but they are susceptible to hydrogen-induced cracking under applied stress during service. In this study, a bolt steel was subjected to Q+T heat treatment, including quenching at 850, 900, 950, 1000 and 1050 °C, followed by tempering at 500 °C. Microstructural characterization, hydrogen permeation tests, and slow strain rate tensile tests were conducted to investigate the effects of quenching temperature on microstructural evolution, hydrogen diffusion behavior and resistance to hydrogen-assisted cracking. As the quenching temperature increased from 850 °C to 1050 °C, the prior austenite grains, packets and blocks were gradually coarsened, the fraction of high-angle grain boundaries decreased from 64.7% to 54.2%, and although partial dissolution of primary carbides may occur during austenitizing, the number/area fraction and size of carbides observed in the final tempered martensitic microstructure increased after the subsequent tempering treatment. Meanwhile, the Nb/Ti-rich precipitates changed only slightly, and the dislocation density increased. The effective hydrogen diffusion coefficient, D_eff, increased with increasing quenching temperature, mainly because grain coarsening significantly reduced the high-angle grain boundary area and weakened the hydrogen-trapping effect of grain boundaries. This dominant effect masked the diffusion-retarding effects caused by increased dislocation density and coarser carbides. With increasing quenching temperature, the strength loss ratio increased from 7.3% to 12.0%, and the plasticity loss ratio increased from 10.0% to 13.6%, indicating enhanced hydrogen-assisted cracking susceptibility. The fracture morphology gradually changed from deep dimples to flat dimples and flattened ductile–brittle mixed features, while the crack propagation path became straighter. A higher quenching temperature weakened the blocking effect of grain boundaries on crack propagation and reduced the resistance of the quenched and tempered bolt steel to hydrogen-assisted cracking. Full article

In the present work, four grades of austenitic stainless steels, namely AISI 321, AISI 316Ti, AISI 309, and AISI 310S, are investigated in terms of electrochemical hydrogenation effect on their room-temperature impact toughness. All the materials were studied in their as-received (AR), i.e., industrially manufactured, material condition. LOM and SEM microstructural analyses combined with phase XRD and EBSD phase analyses revealed in all steels the polygonal-grain austenitic matrix and varying minor amounts of elongated δ-ferrite grains. Moreover, the metastable AISI 321 and AISI 316Ti steels exhibited noticeable occurrence (16% and 10%, respectively) of the BCC-structured phases (i.e., the strain-induced α′-martensite and non-equilibrium δ-ferrite) and little occurrence of primary TiN nitrides (below 1%). The AISI 321 and AISI 316Ti steels exhibited average amounts of 2.95% and 6.32% of δ-ferrite, respectively. The stable AISI 309 steel exhibited the occurrence of intergranular (Cr,Fe)₂₃(C,N)₆ precipitates (below 3%), indicative of prolonged (slow) cooling from the warm working temperature during the material manufacturing. The individual steel grades exhibited variable values of hardness and impact toughness depending strongly on their solid solution alloying and the amounts of individual minor phases in their microstructures. The AISI 316Ti steel exhibited the highest average hardness (273 HV) and lowest impact toughness (160 J/cm²) due to Mo-alloying and having the highest amount of δ-ferrite. The AISI 310S steel showed the highest impact toughness (210 J/cm²) and the second highest hardness (245 HV) thanks to having the most stable austenitic microstructure with the highest Ni- and Cr-alloying. The AISI 321 and AISI 309 steels show similarly low hardness (195 HV vs. 196 HV) and medium values of impact toughness (202 J/cm² vs. 193 J/cm²). More importantly, all the steels under investigation exhibited detectable hydrogen-induced toughening effects, indicated by the negative HEI values. The metastable steels showed the lowest toughening effects (HEI: −2.0% and −3.8% for AISI 321 and AISI 316Ti, respectively), likely due to the adverse effect of α′-martensite. In contrast, the stable steels exhibited much higher toughening (HEI: −5.2% and −7.6% for AISI 309 and AISI 310S, respectively). Microstructural observations indicated that such toughening behavior might be related to the hydrogen-enhanced deformation banding and hydrogen-enhanced deformation twinning mechanisms, dividing the grains into smaller deformation zones, increasing the overall dissipation of deformation energy and consequently the materials’ impact toughness. Full article

xAl₃Zr/Al-5Cu-0.6Mn-0.15Ti composites were fabricated via an in situ reaction method, and the influence of Al₃Zr content on the microstructure and mechanical properties in both as-cast and T6-treated conditions was systematically investigated. The results reveal that the D0₂₃-Al₃Zr content increases in proportion to the K₂ZrF₆ addition level. Following T6 heat treatment, finely dispersed θ′-Al₂Cu precipitates were formed within the matrix, and the α-Al + θ-Al₂Cu eutectic network dissolved. The blocky Al₃Zr particles underwent spheroidization and could continuously exert a grain boundary pinning effect to suppress grain coarsening. After T6 heat treatment, the 4.5 wt.% Al₃Zr composite exhibited average ultimate tensile strengths of 324.44 MPa at room temperature and 123.38 MPa at 350 °C, corresponding to improvements of 8.56% and 23.31%, respectively, relative to the unreinforced base alloy. Following thermal exposure at 350 °C for 24 h, the composite exhibited less pronounced coarsening of the θ′-Al₂Cu precipitates compared with the base alloy, while the Al₃Zr particles retained their morphological and dimensional stability. Consequently, the reductions in both tensile strength and hardness were smaller than those observed for the base alloy. Analysis indicates that Al₃Zr particles significantly refine the α-Al grains and enhance the alloy’s thermal stability. The superior property retention is attributed primarily to the high thermal stability of the Al₃Zr particles, which preserve their dispersion-strengthening contribution at 350 °C, with the reduced θ′ coarsening as a contributing factor. The overall strengthening of the composite arises from the combined and largely independent contributions of Al₃Zr particle strengthening and θ′-Al₂Cu precipitation strengthening. Full article

In this study, we examined the mineralogy, geochemistry and origin of Fe–Mn mineralization occurring as lenses within siliceous mudstones of the Middle Eocene Maden Complex (Durmuştepe, Elazığ, Türkiye) using multivariate statistical methods and Compositional Data Analysis (CoDA). Major-oxide, trace-element and REE analyses were performed on 21 samples (n = 21), comprising 11 ore and 10 host-rock samples. Ore microscopy, discrimination diagrams, PAAS-normalized REE patterns, Principal Component Analysis (PCA), Hierarchical Cluster Analysis (HCA), factor analysis, Kendall correlation and CLR-transformed CoDA-PCA were applied. The ore consists of pyrolusite, braunite, manganite, magnetite and hematite. Massive and felty textures indicate rapid precipitation linked to abrupt physicochemical changes near the vents. Fe/Mn ≈ 1.62 and Co/Ni = 0.03–0.04 support an exhalative origin; Ce/Ce* = 0.10–0.15 (mean 0.11) records a pronounced negative Ce anomaly; and Eu/Eu* = 1.06–1.18 suggests vent-fluid temperatures below ~250 °C. CoDA-PCA shows that Ce is decoupled from the other lanthanides; HCA separates ore from host-rock populations; and factor analysis indicates that Ti–Al–K detrital input diluted ore accumulation. Integrating these results, we interpret Durmuştepe as a proximal volcano-sedimentary hydrothermal-exhalative Fe–Mn system that formed during magmatism in the Maden marginal basin under oxic seawater mixing and contemporaneous detrital sedimentation. The multivariate workflow also provides a reproducible approach for source characterization in similar mixed-origin deposits. Full article

This review focuses on the effects of trace and residual rare-earth elements on inclusion evolution and Nb–Ti–V precipitation behavior in microalloyed steels. Existing studies indicate that trace rare-earth elements can transform conventional Al₂O₃- and MnS-type inclusions into rare-earth oxides, oxysulfides, and sulfides, while also modifying local interfacial states and solute distributions through segregation and interfacial activity. These changes further affect the nucleation sites, growth behavior, coarsening tendency, and spatial distribution of NbC, TiN, VC, and related carbonitrides. To explain the seemingly contradictory precipitation responses reported in the literature, this review examines rare-earth effects from the perspectives of inclusion inheritance, heterogeneous nucleation, interfacial energy modification, local solute redistribution, and thermomechanical processing history. The available evidence suggests that the metallurgical role of trace rare-earth elements cannot be attributed solely to inclusion modification. Instead, their effects arise from the combined influence of inclusion evolution, interfacial activity, local chemical heterogeneity, and precipitation kinetics under specific processing conditions. These insights provide practical guidance for alloy and process design by linking rare-earth addition, inclusion control, and Nb–Ti–V precipitation regulation in microalloyed steels. Full article

Vanadium–titanium magnetite is a critical strategic polymetallic mineral resource in China, and blast furnace smelting represents the dominant large-scale industrial process for its utilization. The melting and fluidity properties of titanium-bearing blast furnace slags (TBFS) directly govern stable blast furnace operation and the recovery efficiency of vanadium–titanium resources. This paper systematically reviews research progress on the melting and flow characteristics of TBFS. The influences of main components (TiO₂, CaO/SiO₂, MgO, Al₂O₃), trace oxides, and strongly reduced products TiC and TiN on slag mineral phases, break point temperature (T_Br) and viscosity are summarized. Combined with X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Raman characterizations and FactSage thermodynamic calculations, the inherent mechanisms are revealed from the perspectives of microstructural network polymerization and crystalline phase precipitation. TiO₂ exerts dual effects: it depolymerizes the silicate network to reduce slag viscosity while promoting the precipitation of high-melting-point perovskite. Al₂O₃ intensifies network polymerization and impairs slag fluidity. MgO, basicity, MnO and BaO can decrease slag viscosity. Solid particles of TiC and TiN generated under the strong reducing atmosphere inside blast furnaces drastically increase slag viscosity and Tbr. This paper proposes that future research should focus on slag systems with higher TiO₂ contents, so as to provide theoretical support for the high-efficiency blast furnace smelting of VTM and resource utilization of titanium-bearing slags. Full article

Photovoltaic mounting structures operate in harsh environments, demanding high strength and elongation. However, a strength–graded product series within the same composition is lacking. Through Ti microalloying and heat treatment, we developed steels with strengths of 500–800 MPa and studied annealing effects at 640–740 °C. Scanning Electron Microscope (SEM) shows ferrite and cementite: with increasing temperature, ferrite changes from elongated to equiaxed via recovery and recrystallization, while cementite remains finely dispersed along grain boundaries. Transmission Electron Microscope (TEM) reveals TiC precipitates, which decrease in number but increase in size at higher temperatures. Grain refinement strengthening, dislocation strengthening, and precipitation strengthening are the primary strengthening mechanisms, contributing 91.2% and 94.4% to the yield strength after annealing at 640 °C and 720 °C, respectively. Within a wide annealing temperature range, the tensile strength fully covers the 550–650–750–800 MPa grades, with the corresponding elongation fluctuating between 12.4% and 25.3%, achieving a good strength–ductility balance. In summary, simply adding a single Ti element and adjusting the annealing temperature allows for the production of test steels with strengths ranging from 500 to 800 MPa and matched elongation. This approach not only reduces costs but also provides experimental evidence for the process development of a series of new steels for photovoltaic mounting brackets. Full article

Heat-treatable aluminum alloys are widely used in aerospace and automotive industries for high-performance structural applications. However, their processing through conventional fusion-based additive manufacturing is limited by solidification-related defects, such as hot cracking, porosity, and elemental segregation. To overcome these limitations, friction-based additive manufacturing (FBAM) has emerged as a promising solid-state alternative. FBAM primarily includes friction stir additive manufacturing (FSAM), additive friction stir deposition (AFSD), friction screw extrusion additive manufacturing (FSEAM), and friction rolling additive manufacturing (FRAM), which differ in feedstock form and process configuration. In these processes, feed material is consolidated through frictional heat generated below the melting temperature, enabling the formation of refined equiaxed microstructures while minimizing solidification defects. Despite these advantages, significant challenges persist in processing heat-treatable aluminum alloys, particularly the 2xxx, 6xxx, and 7xxx series. These include non-uniform microstructure and mechanical properties along the build direction; precipitation instability; process-induced defects, such as tunnel formation; and mechanical properties that are often inferior to those of the corresponding base materials (BMs). Reported FBAM builds generally exhibit equiaxed ultrafine grains below 1 μm; however, the strength and microhardness of heat-treated alloy builds commonly remain around 70–75% of the corresponding BM. Following post-heat treatment, microhardness can be nearly fully recovered, whereas UTS typically reaches about 80–85% of BMs, often with an associated ductility reduction of nearly 50%. This review critically analyzes research reported over the past decade on FBAM processing of heat-treatable aluminum alloys, covering FSAM, AFSD, FSEAM, and FRAM. The key challenges related to microstructural evolution and mechanical performance are systematically discussed for each alloy series. Furthermore, mitigation strategies proposed in the literature, including process parameter optimization, in-process cooling, post-heat treatment, and nanoparticle reinforcement (e.g., SiC, TiC, Ni and ZrO₂), are evaluated. Finally, existing research gaps are identified, and future directions are proposed to support the development of robust, scalable, and high-performance FBAM processes for heat-treatable aluminum alloys. Full article

The coupled effects of Ni and Ti additions on amorphization, spark plasma sintering (SPS) response, and hardness evolution were investigated in Al-rich Al–Fe–Nb-based metastable alloys. Mechanically alloyed Al₈₂Fe₁₄Nb₂Ni₂, Al₈₂Fe₁₄Nb₂Ti₂, and Al₈₂Fe₁₂Nb₂Ni₂Ti₂ powders showed progressive loss of long-range order, with the quinary alloy exhibiting the strongest amorphization tendency, consistent with its higher configurational entropy (5.420 J·mol⁻¹·K⁻¹) and more negative mixing enthalpy (−9.36 kJ·mol⁻¹). SPS displacement analysis revealed that primary displacement contribution occurs during heating and is progressively limited by crystallization-induced stiffening. Consolidation at 500 °C produced amorphous–nanocrystalline composites containing Al₁₃Fe₄ and Al₃Nb, whereas increasing the temperature to 550 °C promoted further devitrification. The highest hardness, 445.4 HV, was obtained for Al₈₂Fe₁₄Nb₂Ni₂, despite its lower amorphous-forming ability than the quinary alloy. This demonstrates that hardness is controlled not by maximum amorphization, but by the kinetic balance between amorphous retention, fine intermetallic precipitation, and densification efficiency. The results identify SPS as a coupled densification–transformation route for designing high-strength Al-based amorphous–nanocrystalline alloys. Full article

The microstructural characteristics and precipitate features of titanium matrix composites (TMCs) are critical to tribological performance. In this study, TiCp/TA15 composites were fabricated via laser powder bed fusion (LPBF). The as-built composite was then heat-treated at 750 °C for 2 h to obtain a uniform duplex (α + β) microstructure with enhanced TiC precipitation, which was labeled as HT-750. The influence of the microstructural evolution on the tribological performance was systematically investigated. Compared to the as-built composite, the HT-750 composite exhibited a microhardness increase from 360.2 ± 6.4 HV to 459.2 ± 3.1 HV, a reduction in the friction coefficient from 0.649 ± 0.167 to 0.581 ± 0.111, and a decrease in the wear rate from 8.24 ± 0.44 × 10⁻⁴ mm³/(N·m) to 4.81 ± 0.39 × 10⁻⁴ mm³/(N·m), indicating a significant enhancement in wear resistance. This improvement is primarily attributed to the synergistic strengthening effect of the duplex matrix and TiC particles, which enhanced the load-bearing capability and suppressed surface plastic deformation. During the friction process, the dominant wear mechanisms of as-built and HT-750 composites evolved over time but exhibited distinct differences. The as-built composites were prone to continuous plastic deformation and damage accumulation, resulting in severe delamination, oxidative, and abrasive wear. Conversely, the HT-750 composites demonstrated higher resistance to plastic deformation and crack propagation, effectively mitigating interfacial shear and inhibiting damage evolution, with the wear mechanism being dominated by oxidative wear accompanied by abrasive wear and minor delamination. This work provides deep insights into the wear mechanisms of additively manufactured TMCs. Full article

GH4141 + 0.2 wt.% Y₂O₃ superalloy was fabricated using laser powder bed fusion (LPBF) technology and subjected to solution and ageing heat treatments. The effects of laser power (1100, 1300, 1500 W) on the microstructure and mechanical properties of the ODS nickel-based superalloy were investigated. The results indicate that as the laser power increased from 1100 W to 1300 W, defects such as cracks and pores in the specimens decreased, the grains were refined, and the microstructure became more uniform; when the laser power was further increased to 1500 W, the grain size coarsened significantly, precipitation phases at the grain boundaries became coarser or locally aggregated, and crack sensitivity increased. EDS analysis revealed enrichment of C, Cr, Mo and Ti in the dark phases at the grain boundaries, which may be associated with MC-type and M₂₃C₆-type carbides; no significant agglomeration of Y₂O₃ particles was observed in the matrix. Room-temperature tensile properties exhibited a pattern of initially increasing and then decreasing with increasing laser power. The tensile strength and elongation after fracture of the specimens were relatively similar under 1100 W and 1500 W conditions, whilst the specimen tested at 1300 W achieved the optimal balance of strength and toughness, with a tensile strength of 1460 MPa and an elongation after fracture of 14.3%, representing increases of approximately 9.8% and 54% compared to the 1100 W and 1500 W conditions, respectively. At 760 °C, the 1300 W specimens still maintained excellent high-temperature strength. Full article

Seismic-resistant reinforcing steels play a key role in structures subjected to earthquake loading, requiring an optimal balance between strength, ductility, and weldability. Microalloying with vanadium (V), niobium (Nb), and titanium (Ti) is widely used to improve these properties through precipitation strengthening and grain refinement. This work aims to contribute to the development of seismic-resistant reinforcing steels for the Moroccan construction sector. A literature review identified key international requirements, including a tensile-to-yield strength ratio (Rm/Re) of 1.15–1.35 and a total elongation at maximum force (Agt ≥ 7%). In parallel, Moroccan reinforcing bars were mechanically and microstructurally characterized. A conventional steel containing 0.65 wt.% Mn and no vanadium was used as a reference. This steel exhibited limited strain-hardening capacity, with Rm/Re ratios between 1.12 and 1.15. To improve this behavior, steels containing 1.1 wt.% Mn with different vanadium additions were investigated. Preliminary results indicate that vanadium microalloying improves mechanical performance through combined precipitation strengthening and ferrite grain refinement. The increase in strength is likely associated with fine V(C,N) precipitates formed during cooling, while ferrite grain refinement appears to contribute to maintaining ductility. This synergistic effect results in a more favorable strength–ductility balance, supporting the development of seismic-resistant reinforcing steels for structural applications. Full article

The present work compares the corrosion performance of additively manufactured (AM) Ti-6Al-4V ELI (Extra-Low Interstitials) alloy manufactured by Laser-Powder Bed Fusion (L-PBF) using virgin powder (Cycle 1/C1 sample) and reused powder feedstock after up to 34 cycles (Cycle 34/C34 sample) of manufacturing. The effect of powder reuse is also evaluated for anodizing and Flash-PEO-coated specimens in Harrison’s (25 °C) and Hanks’ solutions (37 °C), representing simulated atmospheric precipitation and physiological conditions, respectively. Specimens were characterized using common metallographic techniques, X-ray diffraction, scanning electron microscopy and optical profilometry. Corrosion resistance was evaluated using cyclic potentiodynamic polarization (PDP) tests. The oxygen content in the Ti-6Al-4V reaches 0.14 wt.% after 34 cycles (C34) of powder reuse, enhancing its passivity in both Harrison’s and Hanks’ solutions. Both virgin and reused powder builds are susceptible to localized corrosion in Hanks’ solution at potentials above 1.75 V. Melt pool borders are thought to be the preferential sites for localized corrosion, as indicated by Volta potential measurements (ΔV = 100 mV). The number of cycles does not significantly affect the current–voltage responses for anodizing and flash-Plasma Electrolytic Oxidation (Flash-PEO) treatments, although anodizing is slightly more responsive to variations in surface roughness (i.e., real specimen area). Anodizing and Flash-PEO reduce the passive current density by nearly two orders of magnitude. Even after surface treatment, the alloy printed with reused powder revealed better passivity. Flash-PEO coatings yielded significant protection against localized corrosion. This unlocks Flash-PEO processing as a successful protection approach for AM biomedical components. Full article

In this study, the thermodynamic conditions governing TiC formation were systematically investigated based on Gibbs free energy and interaction parameter theory. The effects of temperature and furnace atmosphere on interaction parameters were explicitly incorporated, enabling an improved thermodynamic description of TiC formation under realistic blast furnace conditions. Furthermore, compared with conventional two-dimensional equilibrium analyses, a three-dimensional Ti-C-temperature thermodynamic precipitation surface was established to quantitatively evaluate the effects of temperature, titanium content, and carbon content on TiC precipitation behavior. The results indicate that titanium is the dominant controlling factor for TiC formation, while carbon plays a secondary synergistic role. Compared with dissolved carbon, solid carbon provides more favorable thermodynamic conditions, suggesting that TiC preferentially forms via interactions with high-activity carbon sources such as coke or refractory materials. Based on the modified thermodynamic framework and boundary conditions, a quantitative precipitation criterion was established as 100 × w[Ti]_% + w[C]_% ≥ 10, which ensures TiC precipitation prior to molten iron solidification under representative blast furnace hearth conditions. The proposed criterion provides a practical guideline for titanium addition and carbon regulation in blast furnace ironmaking and improves the thermodynamic prediction capability for titanium-bearing protective phase formation in complex high-temperature metallurgical environments. Full article