Search Results (3,534)

Dye wastewaters are produced in huge amounts every year world-widely and they pose serious threats to ecosystems and human health if not treated properly. High-concentration organic dye wastewaters are usually treated through multiple steps including pretreatment and advanced treatment. In this work, TiO₂ nanoparticles suspended in high-concentration rhodamine B (Rh B) solutions up to 500 mg/L have been subjected to magnetic stirring to initiate tribocatalytic degradation of Rh B. While 100 and 200 mg/L Rh B solutions can be rather thoroughly degraded in beakers with four kinds of bottom/coatings (glass, Al₂O₃, Ti, and PTFE), 300 mg/L Rh B solutions can only be degraded effectively in a beaker with PTFE coating. Even 400 and 500 mg/L Rh B solutions can also be degraded rather thoroughly by TiO₂ nanoparticles in a PTFE-coated beaker. EPR analyses revealed that PTFE coating enhanced the formation of both hydroxyl radicals and superoxide radicals by magnetic stirring-stimulated TiO₂ nanoparticles. These findings highlight the importance of the synergism between materials in friction pairs for tribocatalysis and demonstrate a one-step tribocatalytic degradation of Rh B solutions with concentrations of real Rh B wastewaters. Full article

Photocatalytic membrane reactors (PMRs) are an innovative technology for water treatment, effectively combining membrane filtration and photocatalysis to enhance contaminant removal while enabling the regeneration of fouled membranes. In this study, a new porous film of chitosan that was impregnated with TiO₂ was developed and coated onto a ceramic support by spin coating to form a new porous immobilized PMR. The formed membrane was tested for two reasons: the removal of methylene blue dye by a dead-end filtration process and to demonstrate its ability to self-regenerate under UV exposure. The selective layer of the membrane was characterized using FTIR spectroscopy, X-ray diffraction, scanning electron microscopy (SEM), and water permeability tests. The results confirmed the formation of an amorphous film with no chemical interaction between chitosan and TiO₂. The membrane exhibited an average water permeability of 10.72 L/m²·h·bar, classifying it as either ultrafiltration (UF) or nanofiltration (NF). Dead-end filtration of methylene blue (10 mg L⁻¹) achieved 99% dye removal based on UV–vis analysis of the permeate, while flux declined rapidly due to fouling. Subsequent UV irradiation removed the deposited dye layer and restored approximately 50% of the initial flux, indicating partial self-regeneration. Overall, spin-coated chitosan–TiO₂ layers on ceramic supports provide high dye removal and photocatalytically assisted flux recovery, and further work should quantify photocatalytic degradation during regeneration. Full article

Micro-arc oxidation (MAO) coatings were produced on commercially pure titanium Grade 2 using a composite electrolyte containing sodium phosphate (Na₃PO₄) and sodium silicate (Na₂SiO₃), while varying the applied voltage. The surface morphology, phase composition, and structural features of the coatings were examined using scanning electron microscopy (SEM) and X-ray diffraction (XRD). The coatings exhibited a characteristic crater-like microporous surface morphology associated with the micro-arc discharge process. XRD analysis confirmed the formation of mixed TiO₂ phases in the anatase and rutile modifications, with higher voltages promoting the growth of the thermodynamically stable rutile phase. Corrosion and tribological properties were evaluated in a 3.5 wt.% NaCl solution using potentiodynamic polarization and a ball-on-disc test configuration, respectively. The results revealed a substantial improvement in both corrosion resistance and wear performance compared with bare titanium. The coating formed at 300 V demonstrated the highest wear resistance due to its denser microstructure, whereas the coating produced at 350 V exhibited the lowest friction coefficient and the greatest corrosion resistance, attributed to the increased rutile content. Overall, MAO coatings fabricated in the phosphate–silicate electrolyte effectively enhance the combined operational properties of titanium and can be recommended for applications requiring improved wear and corrosion resistance. Full article

This work presents a green chemistry route to obtain titanium dioxide TiO₂ nanoparticles with an average size of about 13.25 nm using lemongrass (Cymbopogon citratus) extract. For these assessments, TiO₂ nanoparticles were added to the coating at concentrations of 1% and 5% w/w on fiber-cement sheets. Self-cleaning evaluation was analyzed by the photodegradation of methylene blue (MB) dye at concentrations of 5, 10, and 20 mg/L applied to the coated sheet, and then exposed to simulated sunlight. The coating containing 5 wt% TiO₂ nanoparticles showed the highest photodegradation, reaching 93.3% after 4 h under simulated sunlight exposure at the lowest MB concentration (5 mg/L). Additionally, average contact angles of 80.4°, 92.03°, and 104.25° were determined for coatings containing 0%, 1%, and 5 wt% TiO₂, respectively. Moreover, the modified 5 wt% TiO₂ exhibited up to 30.9% greater hydrophobicity than the control. Antifungal efficacy against Aspergillus niger and Penicillium was evaluated using the Poisoned Food method with nanoparticles at concentrations of 1 and 3 mg/mL showing a moderate growth inhibition. In conclusion, the versatility demonstrated suggests potential applications such as a nano-additive for aqueous acrylic coatings, improving hydrophobicity, self-cleaning and antifungal properties, which could be attractive to the construction industry. Full article

In this work, samples of 30KhGS steel coated by thermal spray were investigated. The coating procedure consisted of two stages. At the first stage, a powder mixture of Cu + Al (mass ratio 4:1) was deposited. At the second stage, under the same process parameters, TiC powder was applied. After each spraying stage, the structure, elemental composition and stress state of the coatings were examined. Following the second deposition, hardness and wear resistance of the sample were measured. The results showed that the hardness and wear resistance of the test specimen increased on average by 40% compared to the corresponding properties of 30KhGS steel subjected to quenching and tempering. The residual stress level in the first (lower) coating was higher than in the upper layer; this difference is related to the distinct mechanisms of layer formation. The lower layer forms through melting and subsequent solidification, whereas the top layer forms by liquid-phase sintering. The obtained results demonstrate the effectiveness of the two-layer coating for increasing the hardness and wear resistance of 30KhGS steel, which broadens the possibilities for surface restoration and repair of parts. Full article

Early oxidative stress caused by titanium implants can impair osseointegration. Manganese dioxide (MnO₂) nanozyme coatings have the potential to scavenge H₂O₂ and simultaneously generate O₂ to alleviate hypoxia, but their activity is mostly static, and the ion release is detrimental. A nano-MnO₂/Ti/P(VDF-TrFE) sandwich-structured composite was fabricated, and ferroelectric polarization was applied to preset a tunable surface potential. Kelvin probe force microscopy (KPFM) verified a presettable potential within ±500 mV. Steady-state kinetics confirmed an enhancement in overall catalytic efficiency (higher V_max and lower K_m). This translated to a faster initial decomposition rate at a low, physiologically relevant H₂O₂ concentration (300 μM). Correspondingly, under these oxidative stress conditions, cell survival in the polarized group was higher than that in the unpolarized group, indicating that the enhanced initial rate can have a positive effect in such conditions. Overall, this study demonstrates a proof-of-concept strategy to tune MnO₂ nanozyme catalysis using a polarization-preset surface potential, targeting implantation-relevant ROS-rich conditions. Full article

Background/Objectives: Laser has a prominent place in pharmaceutical industry, especially in the marking of solid dosage forms (SDFs). To combat falsified medicines, this study evaluates QR code marking on the surface of tablets as a supplement to serialization on packaging, using an ultrafast laser to achieve industrially relevant marking speeds while preserving the functional integrity of double film-coated ibuprofen tablets. Methods: Tablets were directly compressed and coated with a double film: the inner layer was a gastro-resistant coating (Acryl-EZE^® MP), while the outer one was a coloured, TiO₂-containing (TC) or TiO₂-free (TF) immediate-release coating (Opadry^®). QR codes were ablated on the tablet surface using various laser parameters (e.g., pulse energy and scanning speed), and the effects were physically, chemically, and microscopically examined to evaluate their properties after this processing. Results: No significant differences were observed between TC and TF coatings. In addition, the readability of QR code is strongly influenced by laser settings and coating types. Furthermore, the used laser has achieved the expected fast marking speed and high-precision coding, which may be economically feasible for pharmaceutical companies. According to the profilometry findings, the ablation depth could be compensated for with an appropriate coating thickness to enable the desired release properties. This was confirmed by the results of SEM, Raman analysis, and in vitro dissolution test. Conclusions: Ultrafast Ti:Sa laser-based QR code marking directly onto the dosage form offers increasing benefits in the healthcare field. However, it may undesirably affect the behavior of the dosage form. This requires careful consideration of formulation and laser processing conditions before application, especially in the case of delayed-release (DR) systems. Full article

Titanium dioxide (TiO₂) thin films were deposited by DC magnetron sputtering and subsequently treated in hot water at 50, 70, and 95 °C for 72 h to investigate the influence of low temperature on their structural optical and functional properties. XRD analysis revealed a progressive transformation from amorphous to anatase phase with increasing treatment temperature, accompanied by an increase in crystallite size from 5.2 to 15.1 nm. FT-IR spectroscopy confirmed enhanced surface hydroxylation and contact angle measurements showed a decrease from 77.4° to 19.7°, indicating a significant improvement in superior wettability. The transmittance spectroscopy revealed a slight narrowing of the optical band gap from 3.34 to 3.21 eV, consistent with improved visible-light absorption. Photocatalytic tests using the Resazurin indicator demonstrated that the film treated at 95 °C exhibited the highest activity, achieving a bleaching time of 245 s three times faster than treated at 50 °C and twice as fast as treated at 70 °C. Under low-intensity solar irradiation, the same sample achieved complete E. coli inactivation within 90 min. These improvements are attributed to increased crystallinity, surface hydroxyl density, and enhanced ROS generation. Overall, this study demonstrates that mild hot-water treatment is an effective, substrate-friendly route to enhance TiO₂ film wettability and multifunctional performance, enabling the fabrication of self-cleaning and antibacterial coatings on fragile materials such as plastics and textiles. Full article

Electrochemical deposition of gold from a sulfite-thiosulfate electrolyte was studied on GaAs–TiAu substrates using polarization curve measurements, gold layer morphology analysis (AFM), and current efficiency determination in the temperature range of 20–65 °C. It was found that increasing the temperature to 50–65 °C makes it possible to raise the gold deposition current density from 2 to 7 mA/cm² while maintaining a current efficiency close to 100% and obtaining compact coatings with a surface root mean square roughness Sq of 6–8 nm. The activation energy of the process is 20–25 kJ/mol. It was shown that electrochemical conditioning of the electrolyte prevents sulfur precipitation, whereas the introduction of excess sulfite ions dissolves the sediment but leads to poorer coating quality. Thus, the feasibility of electrolyte regeneration has been demonstrated, and optimal gold deposition regimes have been determined: 7 mA/cm² at 50 °C and 10 mA/cm² at 65 °C. Full article

WC-based cermet coatings with a CoCrNiAlTi binder were fabricated on 04Cr13Ni5Mo stainless steel substrates using the atmospheric high-velocity air–fuel (HVAF) spraying process. The influence of the air-to-fuel ratio (AFR) on the microstructure, mechanical properties, and wear resistance of the WC-CoCrNiAlTi coatings was systematically investigated. The results indicate that the WC-CoCrNiAlTi coatings primarily consisted of WC, (Co, Ni)₃W₃C and a face-centered cubic (FCC) binder phase. As the AFR increased, the formation of the (Co, Ni)₃W₃C phase gradually decreased. Concurrently, the coating density improved, which was attributed to the enhanced particle melting state and increased flight velocity, leading to better flattening upon impact. The average microhardness of the WC-CoCrNiAlTi coatings gradually increased with an increasing AFR. The coating produced at an AFR of 1.130 exhibited the highest microhardness of 1355.68 HV_0.2. Both the friction coefficient and the wear rate of the coatings decreased progressively as the AFR increased. At the optimal AFR of 1.130, the coating demonstrated the lowest friction coefficient (0.6435) and wear rate (1.15 × 10⁻⁶ mm³·N⁻¹·m⁻¹), indicating a wear resistance 34.85 times that of the stainless steel substrate. Furthermore, the slurry erosion weight loss rate of the WC-CoCrNiAlTi coatings decreased gradually with increasing AFR. The coating sprayed at an AFR of 1.130 showed the minimum erosion rate (1.70 × 10⁻⁶ g·cm⁻²·min⁻¹), which was 24.04 times lower than that of the substrate. The erosion mechanism of the WC-CoCrNiAlTi coatings was identified as the fatigue-induced removal of WC particles under alternating stress. The ductile high-entropy alloy (HEA) binder effectively protects the brittle WC phase through adaptive deformation, thereby significantly mitigating coating damage. Full article

Antibacterial thin-film coatings are of increasing interest for enhancing hygiene in controlled environments such as commercial greenhouses. Phytopathogens including Pseudomonas syringae, and human pathogens such as Escherichia coli, Micrococcus luteus, and Staphylococcus aureus, frequently contaminate greenhouse environments. The present study aimed to develop and evaluate multifunctional magnetron-sputtered glass coatings with strong antimicrobial performance, deposited by physical vapor deposition to achieve precise control of film composition and uniform coverage of large substrates (≥0.25 m²), ensuring industrial-scale applicability. Thin films were fabricated by magnetron sputtering using multi-alloy targets composed of Cu, Sn, Zn, Al, Ni, Fe, Ti, Mn, Nb, or Co. Fourteen distinct coating compositions were characterized using high-resolution transmission electron microscopy, scanning transmission electron microscopy, and energy-dispersive X-ray spectroscopy. Antibacterial performance was evaluated against the following strains: E. coli (PCM 2560), M. luteus (PCM 525), S. aureus (PCM 2602), and P. syringae pv. tomato (IOR2146). Coatings prepared from 90%Cu-10%Sn, 90%Cu-10%Zn, and 80%Cu-20%Ti targets exhibited one of the highest antibacterial efficiencies. These coatings also showed strong mechanical durability and corrosion resistance. Our results indicate that coatings obtained from Cu-based multi-alloy targets by magnetron sputtering are promising candidates for use as durable, antimicrobial inner glass surfaces in future greenhouse applications. Full article

This study evaluated the surface functionalization of a non-equiatomic TiZrNbTaMo high-entropy alloy (HEA) by micro-arc oxidation (MAO) in Cu-rich electrolytes to tailor its performance for biomedical implants. The Cu content was varied, and the resulting coatings were investigated for their morphology, phase constitution, chemical structure, wettability, and cytocompatibility. X-ray diffraction (XRD) measurements of the substrate indicated a body-centered cubic (BCC) matrix with minor HCP features, while the MAO-treated samples depicted amorphous halo with sparse reflections assignable to CaCO₃, CaO, and CaPO₄. Chemical spectroscopic analyses identified the presence of stable oxides (TiO₂, ZrO₂, Nb₂O₅, Ta₂O₅, MoO₃) and the successful incorporation of bioactive elements (Ca, P, Mg) together with traces of Cu, mainly as Cu₂O. MAO treatment increased surface roughness and rendered a hydrophilic behavior, which are features typically favorable to osseointegration process. In vitro cytotoxic assays with MC3T3-E1 cells (24 h) showed that Cu addition did not induce harmful effects, maintaining or improving cell viability and adhesion compared to the controls. Collectively, MAO in Cu-rich electrolyte yielded porous, bioactive, and Cu-incorporated oxide coatings on TiZrNbTaMo HEA, preserving cytocompatibility and supporting their potential for biomedical applications like orthopedic implants and bone-fixation devices. Full article

Reverse electrodialysis (RED) enables the efficient conversion of the chemical potential difference between seawater and freshwater into electricity while simultaneously facilitating hydrogen production for integrated energy utilization. Nevertheless, the widespread deployment of RED remains constrained by the reliance on ruthenium–iridium-coated electrodes, which are expensive and resource-limited. This study proposes the adoption of titanium-based redox electrodes as a replacement for traditional precious metal electrodes and employs a novel spike structure to accelerate hydrogen bubble detachment. The electrochemical performance of titanium electrodes in an RED hydrogen production system was systematically evaluated experimentally. The influences of several parameters on the RED system performance were systematically examined under these operating conditions, including the ruthenium–iridium catalytic layer, operating temperature (15 to 45 °C), electrode rinse solution (ERS) concentration (0.1 to 0.7 M), and flow rate (50 to 130 mL·min⁻¹). Experimental results demonstrate that optimized titanium redox electrodes maintain high electrocatalytic activity while significantly reducing system costs. Under optimal conditions, the hydrogen yield of the Ti redox electrode reached 89.7% of that achieved with the mesh titanium plate coated oxide iridium and oxide ruthenium as electrodes, while the electrode cost was reduced by more than 60%. This is also one of the cost-cutting solutions adopted by RED for its development. Full article

The wear performance of coated and uncoated harrow discs was evaluated under real agricultural field conditions in order to assess the long-term effectiveness of three atmospheric plasma spraying (APS) systems: a Cr₂O₃–SiO₂–TiO₂ ceramic coating, a WC/W₂C–Co carbide coating, and a Co–Cr–Ni–W–C alloy coating. In contrast to most previous studies focused on laboratory testing or short-term trials, the present work provides a comparative long-term field evaluation over 50 ha per disc (1000 ha total) under identical operating conditions in quartz-rich Argic Luvisol soil. Disc wear was quantified through periodic mass-loss and diameter measurements, complemented by microstructural and SEM analyses. The uncoated disc exhibited the most severe degradation, with a total mass loss of approximately 700 g and rapid acceleration of wear after the first 5–10 ha. The ceramic-coated disc showed the highest durability, limiting mass loss to approximately 390 g, corresponding to a reduction of about 44%, and maintaining the largest residual diameter after field operation. The Co-based alloy provided intermediate performance (~16% mass-loss reduction), while the carbide coating showed limited improvement (~7% reduction) due to microcracking and weak carbide–binder interfaces. The results demonstrate that, under real field conditions, coating microstructural integrity is more critical than nominal hardness, and highlight the superior effectiveness of ceramic APS coatings for extending disc service life in abrasive agricultural soils. Full article

Recent studies show that titanium (Ti)-based alloys combine established mechanical strength, corrosion resistance, and biocompatibility with emerging electrical and electrochemical properties relevant to bioelectronics. The main goal of the present manuscript is to give a wide-ranging overview on the use of Ti-alloys in electronics and biomedicine, focusing on a comprehensive analysis and synthesis of the existing literature to identify gaps and future directions. Concurrently, the identification of possible correlations between the effects of the manufacturing process, alloying elements, and other degrees of freedom influencing the material characteristics are put in evidence, aiming to establish a global view on efficient interdisciplinary efforts to realize high-added-value smart devices useful in the field of biomedicine, such as, for example, implantable apparatuses. This review mostly summarizes advances in surface modification approaches—including anodization, conductive coatings, and nanostructuring that improve conductivity while maintaining biological compatibility. Trends in applications demonstrate how these alloys support smart implants, biosensors, and neural interfaces by enabling reliable signal transmission and long-term integration with tissue. Key challenges remain in balancing electrical performance with biological response and in scaling laboratory modifications for clinical use. Perspectives for future work include optimizing alloy composition, refining surface treatments, and developing multifunctional designs that integrate mechanical, biological, and electronic requirements. Together, these directions highlight the potential of titanium alloys to serve as foundational materials for next-generation bioelectronic medical technologies. Full article