Search Results (224)

Polymeric membranes are widely investigated for CO₂ separation; however, their performance is often limited by the permeability–selectivity trade-off. Incorporating metal–organic frameworks (MOFs) and designing composite membrane architectures are promising strategies to overcome these limitations. This study aims to evaluate the effect of incorporating MOF-74 (Cu and Ni variants) into a polydimethylsiloxane (PDMS) selective layer supported on a polysulfone (PSF) membrane for enhanced CO₂/N₂ separation performance. Dual-layer PDMS/PSF composite membranes were fabricated via phase inversion for the PSF support, followed by solution casting of the PDMS/MOF layer. The developed membrane architecture introduces a synergistic design that combines the mechanical robustness of PSF with the selective transport capability of PDMS and the strong CO₂ affinity of MOF-74, offering an effective strategy for improving gas separation efficiency. Gas permeation performance was assessed using single-gas CO₂ and N₂ measurements at feed pressures of 2–5 bar. The incorporation of MOF-74 improved CO₂ transport properties, with the 1 wt.% Cu-MOF-74 composite membrane achieving a CO₂ permeance of 912.5 GPU and a CO₂/N₂ ideal selectivity of 94.75. The dual-layer configuration significantly enhanced permeance compared with unsupported mixed-matrix membranes while maintaining selectivity. Additionally, the composite membranes exhibited improved mechanical strength due to the PSF support layer. The findings demonstrate that dual-layer PDMS/PSF composite membranes incorporating MOF-74 provide a promising proof-of-concept approach for improving CO₂ separation performance. Further studies involving mixed-gas testing and long-term stability are required to assess their practical applicability. Full article

We developed a multi-channel and multilayered polydimethylsiloxane (PDMS) microfluidic platform that integrates cyclic mechanical stimulation, independent reagent delivery, and real-time optical observation within a single device. The platform employs a four-layer architecture comprising a pneumatic valve control layer, an observation channel for cell culture and imaging (24 mm × 4 mm), a medium perfusion layer with independent inlet ports, and a vacuum actuation layer that deforms a 200 μm PDMS membrane under −20 kPa cyclic pressure at 1 Hz. Cyclic membrane strain of 10% was calibrated using fluorescent bead tracking and image analysis. Finite element analysis based on nonlinear Föppl–von Kármán plate theory confirmed that the central cell culture region (60% of membrane area) exhibits a mean von Mises strain of 14.2% with a uniformity of 81.3% (CV = 18.7%), validating relatively uniform mechanical stimulation across the culture surface. As a proof-of-concept, human aortic smooth muscle cells (CRL-1999) cultured under cyclic strain showed significant upregulation of HIF-1$\alpha$ expression (2.5-fold, $p<0.01$) and pronounced F-actin stress fiber alignment visualized by fluorescence microscopy, confirming the platform’s capability for mechanotransduction studies and real-time cellular observation. The multi-channel architecture enables multi-condition parallel testing by simultaneously introducing different reagent concentrations through independent inlet ports while maintaining identical mechanical parameters across all channels, providing a versatile tool for systematic investigation of cellular responses under controlled biomechanical conditions. Full article

Biofilms rapidly form on medical devices such as urinary catheters and surgical materials. These biofilms compromise patient safety and undermine infection prevention and control (IPC). Biofilms also reduce the effectiveness of antibiotics and disinfectants. As a result, they increase healthcare-associated infections and increase costs through device failure and the need for maintenance or replacement. Researchers are increasingly exploring biosurfactants (BSs) as surface coatings and cleaning additives to prevent microbial attachment and disrupt early biofilm formation on medical devices and healthcare-related surfaces. This review examines the translational potential of biosurfactants as preventive, disruptive, and adjunctive antibiofilm agents for medical devices and healthcare-related surfaces. Literature evidence on glycolipids (rhamnolipids, sophorolipids) and lipopeptides (surfactin) from static, flow-based, and microfluidic in vitro models that used clinically relevant materials, such as silicone and polydimethylsiloxane (PDMS), were examined. In our literature search, we focused on pathogens central to IPC, such as Staphylococcus aureus, Pseudomonas aeruginosa, Enterococcus spp., and Candida spp., and it was generally noted that BSs reduced microbial adhesion and delayed early biofilm formation on medical devices and healthcare-related surfaces. Significant evidence also suggests that they partially disrupt biofilms and improve antimicrobial penetration when co-applied, mainly through membrane disruption, destabilization of extracellular substances, interfering with quorum sensing, and synergistic and/or antagonistic interactions with other molecules. Their performance varied with class, formulation, hydrodynamic conditions, and microbial composition. BSs function better as preventive and adjunctive IPC tools than stand-alone antimicrobial agents and can help to reduce biofilm formation on devices and improve surface disinfection. However, translating this promise into practice demands more robust data on long-term safety, stability, and product quality. Full article

Developing environmentally friendly, multifunctional waterproof and breathable membranes (WBMs) has attracted extensive attention and is of great significance but remains challenging. Herein, an environmentally friendly and multifunctional waterborne polyurethane WBM with self-healing and self-cleaning properties is developed in two steps. Firstly, by using polydimethylsiloxane (PDMS) as a hydrophobicity giver and tannic acid (TA) as a crosslinker, a dual-modified waterborne polyurethane (PTWPU) is prepared, which has high surface hydrophobicity due to the surface enrichment of siloxane segments and self-healing performance from the formation of a dynamic phenolic carbamate network. Secondly, by incorporating titanium dioxide (TiO₂) photocatalyst nanoparticles to increase internal porosity and establish hydrophilic pathways, a multifunctional waterborne polyurethane WBM (TPTWPU) is developed. This membrane features further enhanced surface hydrophobicity from generated micro-roughness and effective self-cleaning performance, because TA acts as an electron trap to promote the photocatalytic activity of TiO₂. The TPTWPU membrane shows good hydrophobicity (water contact angle of 115.3°) and satisfactory moisture permeability of 135.0 g/(m²·24 h), which is 61.2% higher than unmodified membranes. Furthermore, it exhibits efficient self-healing, with a recovery rate exceeding 80% within 2 h. This feasible strategy will provide guidance for materials design in multifunctional coatings for textiles and leather. Full article

Myogenic mechanobiology governs how mechanical cues regulate myocyte organization, alignment, and functional maturation; however, in vitro platforms that enable quantitative control and real-time readout of myogenic mechanical microenvironments remain limited. Here, we engineered a pneumatic-driven organ-on-a-chip platform integrating six parallel culture units and a bead-embedded flexible PDMS membrane to deliver cyclic mechanical strain and enable quantitative stress–strain mapping in cardiomyocytes and skeletal muscle cells. Finite element-guided optimization ensured effective membrane deformation, and the platform generated stable and tunable cyclic strain with a strong linear relationship between applied negative pressure (50–700 mbar) and membrane stress and strain. Plasma treatment combined with type I collagen coating restored myogenic cell adhesion and growth on PDMS to levels comparable to standard culture conditions. Under 13% cyclic strain, both cardiomyocytes and skeletal muscle cells exhibited pronounced and highly uniform alignment, with cellular polarity oriented perpendicular to the stretch axis. Moreover, cyclic loading significantly enhanced the expression of contractile maturation markers, including MYH7 in cardiomyocytes and MYH6 in skeletal muscle cells (all p < 0.05), whereas expression of the differentiation regulator MyoG remained unchanged, indicating that mechanical stimulation preferentially promotes structural organization and contractile maturation rather than lineage commitment. Collectively, this quantitatively programmable organ-on-a-chip represents a bioengineered microdevice for studying myogenic mechanobiology, revealing conserved mechanosensitive alignment and maturation responses across myogenic lineages and providing a versatile framework for biomedical engineering research, disease modeling, and mechanotherapeutic screening. Full article

Oily substances (oils, greases, lubricants, etc.) are among the most persistent pollutants for water. They mix with water to form emulsions that contaminate large volumes. Therefore, this project evaluated the use of porous systems (polyurethane foam) modified with polydimethylsiloxane-modified silica (SiO₂/DMS) hybrid ceramics as filtration membranes at the laboratory scale for vegetable oil. The polyurethane foam was modified using sol solutions with various SiO₂/PDMS ratios obtained via the sol–gel method. Tetraethyl-orthosilicate (TEOS) was used as the silica precursor. Three different polydimethylsiloxane chains were employed as the organic fragment: polydimethylsiloxane hydroxyl terminated (DMS-CH₃), aminopropyl-terminated polydimethylsiloxane (DMS-N), and copolymer polydiphenylsiloxane-polydimethylsiloxane hydroxyl terminated (PDS). The siloxane chain was added at a concentration of 20–40% w/w. The modification of the porous system was determined using different characterization techniques, including infrared spectroscopy, which was used to observe the main functional groups. Optical microscopy and SEM were used to identify the hybrid ceramic deposited into the pore structure of the polyurethane sponge. Contact angle measurements revealed the hydrophobic character of the modified material. The removal capacity was evaluated by using vegetable oil as a representative oily contaminant, with values ranging from 43.42 to 96.78 g of oil per gram of adsorbent. In the case of gasoline, removal capacities between 27 and 54 g were observed. This study demonstrated the influence of hydrophobicity on vegetable oil removal, confirming that higher hydrophobicity leads to greater adsorption capacity. Nevertheless, the use of a viscous contaminant introduced challenges in the extraction process from the PS/SiO₂-DMS system. Despite this limitation, the material maintained adequate removal performance for up to five reuse cycles. On the other hand, the removal capacity depends on the amount of polysiloxane chain in the ceramic, as well as the functional group, exhibiting the following behavior: DMS-N < DMS-CH₃ < PDS. This study demonstrates that hydrophobicity is a key property for enhancing the removal capacity of oily substances. Moreover, the control of intermolecular interactions further strengthens this effect, as evidenced in the PS/SiO₂–PDS system. Full article

An organophilic composite membrane, ZIF-67@PDMS, was fabricated to enhance the isolation of natural aromatic compounds. The as-prepared composite membrane was characterized using SEM, EDS, FTIR, XRD, and contact angle measurement. In comparison to pure PDMS, ZIF-67@PDMS, featuring a loading capacity of 2.5 wt% of PDMS and a membrane thickness of 15 μm, demonstrated markedly improved separation performance for the characteristic aroma compounds of strawberries, namely linalool, benzaldehyde, and ethyl acetate. Under optimal conditions, the permeation fluxes of the three compounds were 628.02 mg∙m⁻²∙h⁻¹, 294.82 mg∙m⁻²∙h⁻¹, and 254.14 mg∙m⁻²∙h⁻¹, along with separation factors of 26.48, 7.94, and 6.32, respectively. ZIF-67@PDMS was then employed to isolate aromatic compounds from freshly squeezed strawberry juice. By backfilling the permeate, both the variety and the content of aromatic compounds in strawberry concentrate were notably restored, and its aroma profile also closely resembled that of fresh strawberry juice. Full article

A carbon nanotube (CNT)-integrated microfluidic electrochemical sensor was developed for sensitive nanoparticle detection using gold nanoparticles (AuNPs) as the model analyte. The device incorporated screen-printed polyethylene terephthalate (PET) electrodes, a polydimethylsiloxane (PDMS) microchannel, and a CNT membrane that simultaneously served as a filtration layer and working electrode. This configuration enhanced analyte trapping, increased the electroactive surface area, and accelerated electron transfer under convective flow. The CNT membrane was fabricated by vacuum filtration and torch-assisted bonding, ensuring strong adhesion without adhesives or plasma treatment. Electrochemical analysis showed that the filter-integrated CNT sensor exhibited an oxidation current of 63 µA compared to 11 µA for the non-filter sensor, representing a fifteen-fold sensitivity enhancement. The detection limit improved from 1.0 × 10⁻³ to 7.5 × 10⁻⁴ mol·L⁻¹ with excellent reproducibility (RSD < 5%) and ∼90% accuracy. These findings validated the filtration-assisted accumulation mechanism and demonstrated the effectiveness of CNT-integrated microfluidic sensors for enhanced nanoparticle detection, while highlighting their potential for future adaptation to biosensing applications. Full article

Polydimethylsiloxane (PDMS) is commonly used in gas-separation studies because of its high CO₂ permeability and stable mechanical properties. In this work, mixed matrix membranes (MMMs) were prepared by incorporating the bimetallic MOFs Ni-Cu-MOF-74, Ni-Co-MOF-74, and Ni-Zn-MOF-74 into a PDMS matrix. The membranes were fabricated by solution casting and characterized by SEM, XRD, FT-IR, and BET analyses, which confirmed uniform filler dispersion and the successful incorporation of the MOF-74 structures. Single-gas permeation tests showed clear performance improvements with MOF loading. The best results were obtained for the membrane containing 1 wt.% Ni-Cu-MOF-74, which reached a CO₂ permeability of 3188.25 Barrer and a CO₂/N₂ selectivity of 35.10. The improvement is attributed to the accessible metal sites and high surface area provided by the MOF-74 framework, which enhanced adsorption–diffusion pathways for CO₂ transport. These results show that PDMS/MOF-74 mixed-matrix membranes are effective for CO₂/N₂ separation, with Ni-Cu-MOF-74 achieving the highest performance. Full article

Microfluidic oxygenators promise to advance extracorporeal membrane oxygenation (ECMO) devices with enhanced hemodynamics and low prime volume. We are developing a silicon-based membrane oxygenator that will offer improved gas transfer and fluid flow control. Polyethylene glycol (PEG) has been used to improve hemocompatibility by providing excellent resistance to protein adsorption. Here, we characterized a polyethylene glycol surface modification of composite silicon–PDMS membranes to evaluate their effects on microfluidic oxygenator properties. X-ray photoelectron spectroscopy (XPS) and water contact angle goniometry confirmed successful PEG attachment, evidenced by the presence of characteristic C-O bonds and increased hydrophilicity, which was stable for 2 weeks. Oxygen flux tests demonstrated gas transfer rates as high as 89.6 ± 17.9 mL/min/m² and 50.8 ± 11.7 mL/min/m² for unmodified and PEG-coated membranes, respectively. Protein adsorption studies with human serum albumin (HSA) demonstrated a significant reduction in nonspecific protein binding on PEG-coated membranes with values as low as 14 ± 6 μg/cm². These studies expand on the characterization of our engineered oxygenator membranes and provide insight for the development of future surface optimization strategies to enhance hemocompatibility. Full article

Zero-depth nanopores present a promising solution to the challenges associated with ultrathin membranes used in solid-state resistive pulse sensors for DNA sequencing. Most existing fabrication methods are either complex or lack the nanoscale precision required. In this study, we introduce a cost-effective approach that combines PDMS molding at the intersection of silicon micro-blades with an innovative high-resolution nano-positioning technique. These blades are created through photolithography and a two-step KOH wet etching process, allowing for the formation of sub-50 nm 3D rhombic zero-depth nanopores featuring large vertex angles. To address the limitations of SEM imaging—such as dielectric charging and deformation of PDMS membranes under electron beam exposure—we devised a finite element model (FEM) that correlates electrical conductance with pore size and electrolyte concentration. This model aligns closely with experimental data, yielding a mean absolute percentage error of 3.69%, thereby enabling real-time indirect sizing of the nanopores based on the measured conductance. Additionally, we identified a critical channel length beyond which pore resistance becomes negligible, facilitating a linear relationship between conductance and pore diameter. The nanopores produced using this method exhibited a 2.4-fold increase in conductance compared to earlier designs, highlighting their potential for high-precision DNA sequencing applications. Full article

In recent years, the development of stretchable electronic devices with mechanical properties similar to those of human tissues has attracted increasing research interest in biomedical engineering, wearables, and other fields. These devices have demonstrated, and some other researchers have already shown, promising advancements towards applications that span from measurements of the disruption of model barrier tissues to wearable or implantable devices, soft robotics, and the development of flexible and stretchable batteries. For example, models of barrier tissues, consisting of two compartments separated by a porous membrane, have been used to measure their integrity as well as to investigate the passage of drugs, toxins, and cancer cells through these tissues. Some of these models include an elastomeric membrane which can be stretched to model processes such as breathing and gut peristalsis, while others include electrodes for real-time measurement of barrier tissue integrity. However, to date, microelectrodes have not been fabricated directly on a porous elastomeric membrane. Here, we present lithographically patterned gold electrodes on porous PDMS membranes that enable electronic sensing capabilities in addition to mechanical manipulation. These membranes are incorporated into vacuum-actuated devices which impart cyclic mechanical strain, and their suitability for electrical impedance measurements, even after 1000 stretching cycles under fluids similar to cell culture media, is demonstrated. In the future, we expect to use these electrodes to measure the disruption in model cell barriers as well as to dielectrophoretically trap cells in a region of interest for more rapid assembly of a model tissue. Other areas like wearables, robotics, and power sources will greatly benefit from the further development of this technology. Full article

Conventional thermoplastic polyurethane (TPU) films are commonly used in the field of waterproof and moisture-permeable textiles because of their excellent mechanical properties and flexibility. However, the high water absorption of TPU films limits their application in sophisticated waterproof and moisture-permeable products, particularly in extremely humid environments, where it may compromise the waterproof performance of textiles and negatively affect the wearing comfort. Therefore, to enhance the durability of these films, TPU was hydrophobically modified with end-hydroxy polydimethylsiloxane (PDMS). Because of its unique low-surface-energy properties and excellent hydrophobicity, PDMS substantially reduces the surface energy of the films and provides them with excellent water repellency, effectively addressing the excessive water absorption issue of TPU films. On this basis, a microporous film featuring waterproof and moisture-permeable properties is produced using phase conversion technology. Compared with that of the unmodified sample, the surface energy of silicone-modified TPU (Si-TPU) decreased by 10.56 mJ/m². Furthermore, the water contact angle increased from 83° to 105°, whereas the water absorption rate considerably reduced after the modification. Moreover, Si-TPU was employed for the fabrication of a microporous membrane, which displayed exceptional moisture permeability (8651.34 g/(m²⸱24 h)). Full article

In this study, hydrophilic covalent organic framework (COF) nanosheets with triazine structures and hydrophobic COF nanosheets with fluorinated imine skeletons were designed to enhance the membrane separation process for ethanol pervaporation. The mass transfer of ethanol–water mixtures within the confined structures of COF nanosheets was investigated through experimental characterization and computational simulations, establishing a quantitative relationship between mass transfer performance and the pore size/chemical properties of COF nanosheets. These COF nanosheets were employed to optimize the confined architecture of mixed matrix membranes (MMMs), effectively regulating the critical parameters of MMMs and improving their separation performance. Through systematic investigation of formation mechanisms and modulation principles, we revealed the correlation between confined structural parameters and membrane separation efficiency. This work develops methodologies and foundational theories to overcome the permeability-selectivity trade-off effect, providing theoretical guidance for designing novel membrane materials with ethanol-permelective COF-based MMMs. Full article

High-throughput biological and chemical assays increasingly require parallel sample manipulation using arrays of micronozzle apertures. Liquid-to-liquid ejection avoids air–liquid interfaces, thereby reducing sample evaporation and mechanical stress while simplifying device operation. However, existing microfluidic platforms for parallel handling suffer from high dead volume, limited optical access, and poor scalability due to thick structural layers. Here, we present a transparent three-layer 4 × 4 micronozzle array with 40 μm diameter openings and a photolithographically fabricated SU-8 membrane. Our sacrificial layer process yields a 30 µm SU-8 membrane—approximately a 70% reduction in thickness—thereby lowering vertical channel dead volume and eliminating the need for costly glass etching. The resulting architecture enables parallel particle and nanoliter liquid manipulation with real-time optical clarity and enables water-to-water ejection, avoiding air–liquid interfaces. This work demonstrates the water-to-water ejection of 0.5–10 µm microparticles using a transparent, low-dead volume SU-8/PDMS micronozzle array and provides a basis for future studies on substrate deposition and cell handling workflows. Full article